Xyron Adhesive Application &
Laminating System
®
User's Guide
XYRON 850
®
XYRON 1200
The Xyron 850 / Xyron 1200 is designed to be used with one of
the following replacement cartridges:
Important Notice :
Your Xyron 850 / Xyron 1200 system is designed to permanently
attach a clear film or adhesive to the front and/or back of any
substrate that is run through the machine. The lamination film and
adhesive are not designed to be removed without substantial
damage to the laminated substrate. This process is NOT
recommended for any precious or single source documents.
SL/DL: Double- and single sided lamination.
LAT: Front lamination with adhesive transfer on the reverse.
AT: Single - sided adhesive transfer.
Please follow the attached directions carefully.
GB
Cartridge Replacement
Remove feed tray by
lifting upward and
gently pulling
Remove used
supply cartridge by
pulling outward. If
there is film
away from
between the
dispenser.
rollers, turn handle
counter-clockwise.
To Install New Cartridges
To Install Part-used Cartridges
Position cartridge leader
between the rubber rollers in
dispenser.
Attach reusable cartridge
starter tool to partially
used supply cartridge.
Turn handle clockwise to
advance film
Insert partially used
supply
cartridge
into
dispenser.
Note: tool
should be
positioned
between rubber
rollers in dispenser.
Insert new supply cartridge.
Turn handle clockwise until tool has exited
dispenser and film is aligned and wrinkle-free.
Continue to turn
handle until film is
aligned and wrinkle-
free.
Store reusable
cartridge starter
tool for later use.
Install feed tray
and trim off
excess film
Install feed tray
and trim off
excess film
using cut blade.
using cut blade.
Supplies available for:
®
®
XYRON 850
XYRON 1200
Laminating Cartridges (DL Series)
Laminating Cartridges (DL and SL Series)
Xyron Technical Hotline
1-800-793-3523 - USA
+45-7594-5866 - Europe
DL1101-100 Two-Sided Lamination
DL201-100 Two-Sided Lamination General use - Gloss Finish
SL201-100 One-Sided Lamination General use - Gloss Finish
DL601-200 2 x Two-Sided Lamination General use 4 inch (106mm)
SL601-200 4” w - One-Sided Lamination General Use - Gloss Finish
General use - Gloss Finish
SL1101-100 One-Sided Lamination
General use - Gloss Finish
Adhesive Application Cartridges (AT Series)
Adhesive Application Cartridges (AT Series)
AT1101-50 Adhesive Application -
AT201-50 Adhesive Application - Permanent High Tack
AT202-50 Adhesive Application - Permanent Low Tack
AT205-50 Adhesive Application - Permanent Acid Free
AT206-50 Adhesive Application - Non Permanent Repositionable
Permanent High Tack
¤
®
AT1105-50 Adhesive Application -
Permanent Acid Free
Xyron, Inc.
AT1106-50 Adhesive Application -
15820 North 84th Street
Scottsdale, AZ 85260, USA
1-800-793-3523
Non Permanent Repositionable
AT601-100 2 x Adhesive Application - Permanent High Tack
4 inch (106mm)
Combination One Side Lamination /
Combination One Side Lamination /
One Side Adhesive Application (LAT Series)
One Side Adhesive Application (LAT Series)
FAX: 480-443-0118
LAT1101-50
LAT201-50 1 Side Laminate / 1 Side Adhesive Application
www.xyron.com
1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Permanent High
Tack Adhesive)
(General Use Laminate / Permanent High Tack Adhesive)
LAT202-50 1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Permanent Low Tack Adhesive)
LAT1106-50
1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Non Permanent
Repositionable Adhesive)
LAT206-50 1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Non-permanent Repositionable Adhesive)
®
Combination One Side Lamination /
One Side Magnet (LM Series)
Combination One Side Lamination /
One Side Magnet (LM Series)
Xyron, Inc. USA
Xyron Europe A/ S
Xyron Asia
LM201-12 1 Side Laminate / 1 Side Magnet
LM1101-10 1 Side Laminate / 1 Side Magnet
(General Use Laminate / Magnet Backing)
(General Use Laminate / Magnet Backing)
© 2001 Xyron, Inc.
|