by
XPower Pocket Inverter 100
t
1-800-394-0440 (toll free in North America)
1-604-422-2777 (direct)
f
1-604-420-2145
e
Owner's Guide
975-0205-01-01 REV. A
Printed in China
About Xantrex
Xantrex Technology Inc. is a world-leading supplier of advanced
power electronics and controls with products from 50 watt mobile
units to one MW utility-scale systems for wind, solar, batteries, fuel
cells, microturbines, and backup power applications in both grid-
connected and stand-alone systems. Xantrex products include
inverters, battery chargers, programmable power supplies, and
variable speed drives that convert, supply, control, clean, and
distribute electrical power.
Trademarks
XPower by Xantrex is a trademark of Xantrex International.
Xantrex is a registered trademark of Xantrex International.
Other trademarks, registered trademarks, and product names are the
property of their respective owners and are used herein for
identification purposes only.
Notice of Copyright
XPower Pocket Inverter 100 Owner’s Guide
© March 2005 Xantrex International. All rights reserved.
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX
TECHNOLOGY INC. (“XANTREX”)
(a) MAKES NO WARRANTY AS TO THE ACCURACY,
SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER
INFORMATION PROVIDED IN ITS MANUALS OR OTHER
DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR
DAMAGE, WHETHER DIRECT, INDIRECT, CONSEQUENTIAL OR
INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH
INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE
ENTIRELY AT THE USER’S RISK.
Date and Revision
March 2005 Revision A
Part Number
975-0205-01-01
Contact Information
Telephone: 1 800 394 0440 (toll free North America)
1 360 925 5097 (direct)
Fax:
1 800 994 7828 (toll free North America)
1 360 925 5143 (direct)
Email:
Web:
Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Important Safety Information . . . . . . . . . . . . . 3
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 3
Additional Safety Guidelines . . . . . . . . . . . . . . . . . 7
3. Safety Features. . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Inverter Features . . . . . . . . . . . . . . . . . . . . . . . . 9
5. Using the Inverter . . . . . . . . . . . . . . . . . . . . . . 10
Using the DC Cable with Cigarette Lighter Plug . 10
Using the DC Cable with Airplane Power Plug . . 11
Airline Compatibility . . . . . . . . . . . . . . . . . . . . . . . 12
6. Inverter Operation. . . . . . . . . . . . . . . . . . . . . . 13
Operating Guidelines . . . . . . . . . . . . . . . . . . . . . . . 13
Battery Operating Time . . . . . . . . . . . . . . . . . . . . 15
Interference with Electronic Equipment . . . . . . . . 15
Buzzing sound in audio systems and radios. . . . . . 16
Television interference. . . . . . . . . . . . . . . . . . . . . . 16
7. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 17
Replacing the Fuse . . . . . . . . . . . . . . . . . . . . . . . . 19
1
8. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 20
AC Power Output . . . . . . . . . . . . . . . . . . . . . . . . . 20
USB Power Output . . . . . . . . . . . . . . . . . . . . . . . . 20
DC Power Specifications . . . . . . . . . . . . . . . . . . . 21
Physical Specifications . . . . . . . . . . . . . . . . . . . . . 21
9. Warranty and Return . . . . . . . . . . . . . . . . . . . 22
2
1 Introduction
Thank you for purchasing the XPower Pocket Inverter
100. The XPower inverter is part of a family of
advanced high-performance power inverters from
Xantrex, the leader in high-frequency inverter design.
Connected to the 12 volt outlet in your vehicle, the
XPower inverter efficiently and reliably powers a
wide variety of loads through both the AC outlet and
USB port.
The XPower inverter uses reliable solid state power
electronics for years of safe, trouble-free operation
and includes automatic safety monitoring circuitry to
protect it, and your battery, from inadvertent overload
conditions.
Read this guide before connecting or using the
XPower inverter, and save it for future reference. The
main topics in the guide are:
•
•
•
•
Safety information (page 3)
XPower inverter features (page 9)
Instructions for connecting the inverter (page 10)
Operating guidelines (page 13)
1
•
•
•
Troubleshooting information (page 17)
Specifications (page 20)
Warranty and service information (page 22)
2
2 Important Safety Information
Misusing or incorrectly connecting the XPower
inverter may damage the equipment or create
hazardous conditions for users. Read the following
safety instructions and pay special attention to all
Caution and Warning statements in the guide.
Warnings identify conditions that may result in
personal injury or loss of life.
Cautions identify conditions or practices that may
damage the unit or other equipment.
Warnings and Cautions
WARNING
Keep children away from the XPower inverter. The
inverter generates the same potentially lethal AC
power as a normal household wall outlet. Treat the
outlet with respect!
3
WARNING
The XPower inverter housing may become
uncomfortably warm, reaching 140° F (60° C) under
extended high power operation. During operation,
keep it away from materials that may be affected by
high temperatures.
WARNING
Do not use the XPower inverter in the presence of
flammable fumes or gases, such as in the bilge of a
gasoline powered boat, or near propane tanks. Do
not use the XPower inverter in an enclosure
containing automotive-type, lead-acid batteries.
These batteries, unlike sealed batteries, vent
explosive hydrogen gas, which can be ignited by
sparks from electrical connections.
4
WARNING: Shock hazard
Use caution when inserting an AC plug into the
three-prong AC outlet. The prongs of an AC plug
can become bent from misuse. If an AC plug is
improperly inserted into the AC outlet, a bent prong
can slip outside the inverter and become a shock
hazard.
WARNING: Shock hazard
Grip the inverter carefully when inserting or
removing an AC plug. Keep your fingers clear of
the AC outlet. Ensure that your fingers do not
contact the prongs of an AC plug when the plug is
partially inside the inverter.
5
CAUTION: Output non-sinusoidal
Some chargers for small nickel-cadmium batteries
can be damaged if connected to the XPower
inverter. Do not use the inverter with the following
appliances:
•
Small battery-operated appliances like
rechargeable flashlights, some rechargeable
shavers, and night lights that are plugged
directly into an AC receptacle to recharge.
Battery chargers used in hand power tools.
These chargers display a warning label stating
that dangerous voltages are present at the
charger battery terminals.
•
CAUTION
Do not connect live AC power to the XPower
inverter’s AC outlets. This will damage the inverter,
and the damage is not covered by warranty.
Do not connect any AC load that has its neutral
conductor connected to ground to the XPower
inverter.
6
Additional Safety Guidelines
•
•
•
•
Do not insert foreign objects in the XPower
inverter outlets or other openings.
Never connect the inverter to power utility AC
distribution wiring.
Do not use the XPower inverter in temperatures
over 100° F (40° C).
Do not expose the XPower inverter to water, rain,
snow, or spray.
Failure to follow these safety guidelines may cause
personal injury and/or damage to the XPower inverter.
It may also void your product warranty.
7
3 Safety Features
These advanced safety features are built into the
XPower inverter:
•
Electronic overload protection with automatic
shutdown
•
•
•
User-replaceable 10 A fuse
Low battery voltage shutdown
High-input voltage protection with automatic
shutdown
•
•
Overheat protection with automatic shutdown
Output short circuit protection
8
4 Inverter Features
Pocket Inverter 100
Ventilation
openings
Fuse
DC cable port
Power/Fault light
USB power port
AC outlet
DC Cable
Airplane
power plug
Cigarette lighter
plug adapter
Figure 1
9
5 Using the Inverter
Through its AC outlet, the XPower inverter is capable
of continuously powering most 120 V AC products
that use 100 W or less. The XPower inverter can also
power or charge most consumer electronics that have
USB power ports.
The XPower inverter’s AC output waveform, called
“modified sine wave,” is designed to function
similarly to the sine wave shape of utility power.
Using the DC Cable with Cigarette
Lighter Plug
Due to the limitations of 12 V outlets in vehicles or
boats, the XPower inverter should only be used to
supply AC power to products that require 100 W
(about 0.8 A) or less.
1. Attach the cigarette lighter plug adapter to the DC
cable.
2. Plug the DC cable into the DC cable port on the
XPower inverter. See Figure 1.
3. Insert the plug of this cable into the 12 V outlet.
10
4. Plug the device you want to operate into the
XPower inverter. See “Inverter Operation” on
page 13.
5. When the power inverter is not in use, unplug it
from the 12 V outlet to prevent slight discharge of
the battery.
Using the DC Cable with Airplane Power
Plug
1. Plug the DC cable into the DC cable port on the
XPower inverter. See Figure 1.
2. Insert the plug of this cable into the 12 V outlet.
3. Plug the device you want to operate into the
XPower inverter. See “Inverter Operation” on
page 13.
11
Airline Compatibility
Table 1 provides a list of airlines, aircraft, and
passenger classes that have DC power sockets
compatible with the XPower Pocket Inverter 100.
Table 1 Airline Compatibility
Airline
Aircraft
Passenger Class
Business Class
Air Canada
Air China
Air France
American
American
A330, A340
747-400
A330-200
DC-10
Business Class
1st Class, Business
1st Class, Business
727-200, 737-800, 767-300, All Classes
MD-80, MD-11
Cathay Pacific 747-400, 777-200, A330
All Classes
Continental
Delta
767-200, 767-400
737-800, 767-400
747-400
Business Class
All Classes
Qantas
1st Class, Business
1st Class, Business
1st Class
Swiss Air
United
MD-11
767-300
Virgin
747-200, A340-300
1st Class
12
6 Inverter Operation
1. When properly connected to a 12 V outlet, the
light will glow blue, indicating the inverter is
ready.
2. Plug the product(s) you want to operate into the
AC outlet or USB port and switch them on (if
necessary).
Operating Guidelines
•
As the battery is used, voltage begins to fall.
When the XPower inverter senses that the voltage
at its DC input has dropped to 10.5 V, the inverter
automatically shuts down and the light glows red,
indicating a fault. This prevents the battery from
being damaged. Turn off any devices that the
XPower inverter is powering.
Important: Vehicle batteries are designed to provide
brief periods of very high current needed for engine
starting. They are not intended for constant deep discharge.
Regularly operating the XPower inverter from a vehicle
battery until low-voltage shutdown occurs will shorten the
life of the battery.
13
•
•
If an AC product rated higher than 100 W is
plugged into the XPower inverter, the inverter
will shut down. The red fault light comes on.
If the XPower inverter exceeds a safe operating
temperature, due to insufficient ventilation or a
high-temperature environment, it automatically
shuts down. The red fault light comes on.
•
Should a defective battery charging system cause
the battery voltage to rise to dangerously high
levels, the XPower inverter automatically shuts
down. The red fault light comes on.
CAUTION
Although the XPower inverter incorporates
protection against over-voltage, it may still be
damaged if the input voltage exceeds 16 V.
•
In the event of an overload, low battery voltage or
overheating, the XPower inverter automatically
shuts down.
14
Battery Operating Time
Operating time will vary depending on the charge
level of the battery, its capacity and the power level
drawn by the particular AC load, USB load, or
combination of both. With a typical vehicle battery
and a 80 W load, an operating time of 4 to 5 hours or
more can be expected.
When using a vehicle battery as a power source, it is
strongly recommended to start the vehicle every hour
or two to recharge the battery before its capacity drops
too low. The XPower inverter can operate while the
engine is running, but the normal voltage drop that
occurs during starting of the engine may trigger the
inverter’s low voltage shutdown feature.
Interference with Electronic Equipment
Generally, most AC products operate with the XPower
inverter just as they would with household AC power.
Below is information concerning two possible
exceptions.
15
Buzzing sound in audio systems and radios
Some inexpensive stereo systems and AM-FM radios
have inadequate internal power supply filtering and
“buzz” slightly when powered by the XPower
inverter. Generally, the only solution is an audio
product with a higher quality filter.
Television interference
The XPower inverter is shielded to minimize its
interference with TV signals. However, with weak TV
signals interference may be visible in the form of lines
scrolling across the screen. The following should
minimize or eliminate the problem:
•
•
•
Increase the distance between the XPower
inverter and the TV, antenna and cables.
Adjust the orientation of the XPower inverter,
television, antenna and cables.
Maximize TV signal strength by using a better
antenna and use shielded antenna cable where
possible.
16
7 Troubleshooting
PROBLEM: AC product will not operate, no inverter
lights are ON.
Possible cause
Remedy
Battery is defective. Check battery and replace if
required.
Loose connections.
Fuse is blown.
Check connections.
Replace fuse (see page 19).
PROBLEM: Measured inverter output is too low.
Possible cause
Remedy
Standard “average-
reading” AC voltmeter
used to measure output
voltage, resulting in an
apparent reading 5 to 15 V
too low.
Inverter’s “modified sine
wave” output requires “true
RMS” voltmeter for accurate
measurements.
Battery voltage is too low. Recharge battery.
17
PROBLEM: AC product will not operate, red FAULT
light ON.
Possible cause
Remedy
AC product(s) connected Use a product with a power
are rated at more than the rating less than the inverter’s
inverter’s continuous
power rating; overload
shutdown has occurred.
continuous power rating.
AC product is rated less Product exceeds inverter’s
than the inverter’s surge capability. Use a product
continuous power rating; with starting surge power
high starting surge has
caused overload
shutdown.
within the inverter’s capability.
Battery is discharged.
Recharge battery.
18
Possible cause
Remedy
The inverter has
Unplug inverter from DC
overheated due to poor
socket and allow to cool for 15
ventilation and has shut minutes. Remove objects
down.
covering unit. Move the
inverter to a cooler place.
Reduce load if continuous
operation is required. Restart.
Replacing the Fuse
The XPower inverter has a replaceable 10 A fuse.
Remove the blown fuse from the back of the unit and
®
replace it with a Littelfuse Mini fuse, Littelfuse
catalog number 297 010.
CUSTOMER SERVICE HOTLINE: 1-800-394-0440
19
8 Specifications
Specifications are subject to change without notice.
AC Power Output
AC output voltage (nominal)
Continuous AC output power
5 minutes AC output power
Maximum AC output surge power
AC output frequency
120 V AC
80 W
100 W
160 W
60 ± 4 Hz
Modified sine wave
AC output waveform
USB Power Output
DC output voltage
5 V DC
DC output current (max.)
0.5 A DC
20
DC Power Specifications
DC input voltage range
10.5–15.5 VDC
Battery drain with no AC load
(at 12 V input)
0.25 A
90%
Efficiency (maximum)
Low battery shutdown point (nominal) 10.5 V
High battery shutdown point
(nominal)
15.5 V
Physical Specifications
Ambient operating temperature range
0 °C–40 °C (32 °F–104 °F)
Dimensions (L × W × H)
5 1/2 × 3 1/8 × 3/4"
(140 × 80 × 20 mm)
Weight
0.5 lb. (227 g)
21
9 Warranty and Return
Warranty
What does this warranty cover? This Limited Warranty
is provided by Xantrex Technology, Inc. ("Xantrex") and
covers defects in workmanship and materials in your
XPower inverter. This warranty period lasts for 1 year from
the date of purchase at the point of sale to you, the original
end user customer. You require proof of purchase to make
warranty claims.
What will Xantrex do? Xantrex will, at its option, repair
or replace the defective product free of charge, provided that
you notify Xantrex of the product defect within the
Warranty Period, and provided that Xantrex through
inspection establishes the existence of such a defect and that
it is covered by this Limited Warranty.
Xantrex will, at its option, use new and/or reconditioned
parts in performing warranty repair and building
replacement products. Xantrex reserves the right to use parts
or products of original or improved design in the repair or
replacement. If Xantrex repairs or replaces a product, its
warranty continues for the remaining portion of the original
Warranty Period or 90 days from the date of the return
22
shipment to the customer, whichever is greater. All replaced
products and all parts removed from repaired products
become the property of Xantrex.
Xantrex covers both parts and labor necessary to repair the
product, and return shipment to the customer via a Xantrex-
selected non-expedited surface freight within the contiguous
United States and Canada. Alaska and Hawaii are excluded.
Contact Xantrex Customer Service for details on freight
policy for return shipments outside of the contiguous United
States and Canada.
How do you get service? If your product requires
troubleshooting or warranty service, contact your merchant.
If you are unable to contact your merchant, or the merchant
is unable to provide service, contact Xantrex directly at:
Telephone: 1 800 394 0440 (toll free North America)
1 360 925 5097 (direct)
Fax:
1 800 994 7828 (toll free North America)
1 360 925 5143 (direct)
Email:
Direct returns may be performed according to the Xantrex
Return Material Authorization Policy described in your
product manual. For some products, Xantrex maintains a
23
network of regional Authorized Service Centers. Call
Xantrex or check our website to see if your product can be
repaired at one of these facilities.
What proof of purchase is required? In any warranty
claim, dated proof of purchase must accompany the product
and the product must not have been disassembled or
modified without prior written authorization by Xantrex.
Proof of purchase may be in any one of the following forms:
•
•
•
The dated purchase receipt from the original purchase
of the product at point of sale to the end user, or
The dated dealer invoice or purchase receipt showing
original equipment manufacturer (OEM) status, or
The dated invoice or purchase receipt showing the
product exchanged under warranty
24
What does this warranty not cover? This Limited
Warranty does not cover normal wear and tear of the product
or costs related to the removal, installation, or
troubleshooting of the customer's electrical systems. This
warranty does not apply to and Xantrex will not be
responsible for any defect in or damage to:
a) the product if it has been misused, neglected, improp-
erly installed, physically damaged or altered, either
internally or externally, or damaged from improper use
or use in an unsuitable environment;
b) the product if it has been subjected to fire, water,
generalized corrosion, biological infestations, or input
voltage that creates operating conditions beyond the
maximum or minimum limits listed in the Xantrex
product specifications including high input voltage
from generators and lightning strikes;
c) the product if repairs have been done to it other than by
Xantrex or its authorized service centers (hereafter
"ASCs");
d) the product if it is used as a component part of a prod-
uct expressly warranted by another manufacturer;
e) the product if its original identification (trade-mark,
serial number) markings have been defaced, altered, or
removed.
25
Disclaimer
Product
THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE
WARRANTY PROVIDED BY XANTREX IN CONNECTION
WITH YOUR XANTREX PRODUCT AND IS, WHERE
PERMITTED BY LAW, IN LIEU OF ALL OTHER
WARRANTIES, CONDITIONS, GUARANTEES,
REPRESENTATIONS, OBLIGATIONS AND LIABILITIES,
EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE IN
CONNECTION WITH THE PRODUCT, HOWEVER ARISING
(WHETHER BY CONTRACT, TORT, NEGLIGENCE,
PRINCIPLES OF MANUFACTURER'S LIABILITY,
OPERATION OF LAW, CONDUCT, STATEMENT OR
OTHERWISE), INCLUDING WITHOUT RESTRICTION ANY
IMPLIED WARRANTY OR CONDITION OF QUALITY,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE TO THE EXTENT REQUIRED UNDER
APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE
LIMITED IN DURATION TO THE PERIOD STIPULATED
UNDER THIS LIMITED WARRANTY.
IN NO EVENT WILL XANTREX BE LIABLE FOR ANY
SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSSES, COSTS OR
26
EXPENSES HOWEVER ARISING WHETHER IN CONTRACT
OR TORT INCLUDING WITHOUT RESTRICTION ANY
ECONOMIC LOSSES OF ANY KIND, ANY LOSS OR
DAMAGE TO PROPERTY, ANY PERSONAL INJURY, ANY
DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF
MISUSE OR ABUSE, OR THE INCORRECT INSTALLATION,
INTEGRATION OR OPERATION OF THE PRODUCT.
Exclusions
If this product is a consumer product, federal law does not
allow an exclusion of implied warranties. To the extent you
are entitled to implied warranties under federal law, to the
extent permitted by applicable law they are limited to the
duration of this Limited Warranty. Some states and
provinces do not allow limitations or exclusions on implied
warranties or on the duration of an implied warranty or on
the limitation or exclusion of incidental or consequential
damages, so the above limitation(s) or exclusion(s) may not
apply to you. This Limited Warranty gives you specific
legal rights. You may have other rights which may vary
from state to state or province to province.
Warning: Limitations On Use
Please refer to your product manual for limitations on uses
of the product.
27
SPECIFICALLY, PLEASE NOTE THAT THE XPOWER
INVERTER SHOULD NOT BE USED IN CONNECTION WITH
LIFE SUPPORT SYSTEMS OR OTHER MEDICAL
EQUIPMENT OR DEVICES. WITHOUT LIMITING THE
GENERALITY OF THE FOREGOING, XANTREX MAKES NO
REPRESENTATIONS OR WARRANTIES REGARDING THE
USE OF THE XANTREX XPOWER INVERTER IN
CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER
MEDICAL EQUIPMENT OR DEVICES.
Please note that the XPower inverter is not intended for use
as an uninterruptible power supply and Xantrex makes no
warranty or representation in connection with any use of the
product for such purposes.
28
Return Material Authorization Policy
Before returning a product directly to Xantrex you must
obtain a Return Material Authorization (RMA) number and
the correct factory "Ship To" address. Products must also be
shipped prepaid. Product shipments will be refused and
returned at your expense if they are unauthorized, returned
without an RMA number clearly marked on the outside of
the shipping box, if they are shipped collect, or if they are
shipped to the wrong location.
When you contact Xantrex to obtain service, please have
your instruction manual ready for reference and be prepared
to supply:
•
•
•
The serial number of your product
Information about the installation and use of the unit
Information about the failure and/or reason for the
return
•
A copy of your dated proof of purchase
29
Return Procedure
1. Package the unit safely, preferably using the original
box and packing materials. Please ensure that your
product is shipped fully insured in the original
packaging or equivalent. This warranty will not apply
where the product is damaged due to improper
packaging.
2. Include the following:
•
The RMA number supplied by Xantrex
Technology, Inc. clearly marked on the outside of
the box.
•
•
•
A return address where the unit can be shipped.
Post office boxes are not acceptable.
A contact telephone number where you can be
reached during work hours.
A brief description of the problem.
3. Ship the unit prepaid to the address provided by your
Xantrex customer service representative.
If you are returning a product from outside of the USA
or Canada In addition to the above, you MUST include
return freight funds and are fully responsible for all
documents, duties, tariffs, and deposits.
30
If you are returning a product to a Xantrex Authorized
Service Center (ASC) A Xantrex return material
authorization (RMA) number is not required. However, you
must contact the ASC prior to returning the product or
presenting the unit to verify any return procedures that may
apply to that particular facility.
Out of Warranty Service
If the warranty period for your XPower inverter has expired,
if the unit was damaged by misuse or incorrect installation,
if other conditions of the warranty have not been met, or if
no dated proof of purchase is available, your inverter may be
serviced or replaced for a flat fee.
To return your XPower inverter for out of warranty service,
contact Xantrex Customer Service for a Return Material
Authorization (RMA) number and follow the other steps
outlined in “Return Procedure” on page 30.
Payment options such as credit card or money order will be
explained by the Customer Service Representative. In cases
where the minimum flat fee does not apply, as with
incomplete units or units with excessive damage, an
additional fee will be charged. If applicable, you will be
contacted by Customer Service once your unit has been
received.
31
|