Xantech Switch HDMI4X1 User Manual

HDMI4X1  
User Manual  
- 1 -  
 
INSTRUCTIONS  
1 Connect the supplied cables from the HDTV HDMI sources into the 4x1 HDMI Switcher  
inputs.  
2 Connect the cables from your display (monitor or projector) into the HDMI out of the 4x1 HDMI  
Switcher.  
3 Plug the 5VDC power supply into the 4x1 HDMI Switcher.  
* Adjust the EQ knob to remove signal noise resulting from longer input cables  
How to Control the 4x1 HDMI Switcher  
Use the RMT4-IR remote control to toggle between sources.  
RMT4-IR INSTRUCTIONS  
1. Remove battery cover from the back of the RMT4-IR remote.  
2. Verify that dip switches 1 & 2 are in the down (OFF) position.  
3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is  
not marked must be facing down.  
4. Test the RMT4-IR remote by pressing ONLY one button at a time. The indicator light on the remote  
will flash once each time you press a button. WARNING: Do not press multiple buttons  
simultaneously and do NOT press buttons rapidly. These actions will cause the remote to reset and  
steps 1-4 will have to be repeated.  
Note: The RMT4-IR ships with two batteries. One battery is required for operation, the second battery  
is complimentary.  
The optional IR extender allows you to relocate your HDMI Switcher and still have IR control of the  
HDMI Switcher  
IREXTENDER  
1 Plug the IR extender into the Remote port on the front of the Switcher Unit  
2 Flip the Dip Switch 1 underneath the unit to the ON position  
RMT4-IR CODE CONFLICTS  
There are matching pairs of dip switches underneath the Switcher unit and under the  
remote battery cover. Switch 1 & 2 on the Remote and Switch 1 & 2 underneath the unit  
are the matching switches. These switches need to be matched for the remote to  
communicate with the switcher. There are 4 possible sets of IR codes and at least one of  
these sets should be able to resolve any IR conflicts with other home theater devices.  
- 3 -  
 
- 4 -  
 
RS232 INTERFACE  
Binary Table  
ASCII  
Input  
Binary  
1
2
3
4
1
2
3
4
0011 0001  
0011 0010  
0011 0011  
0011 0100  
Terminal Settings  
Bits per second  
Data bits  
19200  
8
Parity  
Stop bits  
None  
1
Flow Control  
None  
SPECIFICATIONS  
Video Amplifier Bandwidth  
Input Video Signal  
Input DDC Signal  
Single Link Range  
Input Connector Type  
Output Connector Type  
Remote Control Port  
Power Consumption  
Power Supply  
1.65 GHz  
1.2 volts p-p  
5 volts p-p (TTL)  
1080p / 1920 x 1200  
HDMI  
HDMI  
Male RS232  
15 Watts (max.)  
5VDC  
Dimensions  
Shipping Weight  
8.25”W x 1.125”H x 2.75”D  
5 Lbs  
- 5 -  
 
Technical Support  
Mailing Address  
Hours:  
Phone:  
7AM-5PM Pacific  
800.843.5465  
press 2 for Tech Support  
800.492.6832  
Xantech Corporation  
13100 Telfair Avenue, 2/F  
Sylmar, CA 91342  
Fax:  
email:  
HDMI4X1 User Manual © 2007 Xantech Corporation  
This document is copyright protected. No part of this manual may be copied or reproduced in any  
form without prior written consent from Xantech Corporation.  
Document Number 08905128A  
- 6 -  
 

Weider Home Gym 9940 User Manual
Weider Home Gym WESY74090 User Manual
Whirlpool Double Oven BMVE 8200 User Manual
Whirlpool Refrigerator 3ET16NK User Manual
WiLife Security Camera V 15 User Manual
Williams Sound Switch MOD 232 User Manual
Xerox Copier 7655 User Manual
Zanussi Freezer ZVR 45 R User Manual
Zanussi Microwave Oven ZM266 User Manual
Zanussi Washer ZWG 7120 P User Manual