X10 Wireless Technology Home Security System MS10A User Manual

Motion Detector, Model MS10A Set Up and Operating Instructions  
Installation  
If the Console is NOT armed and in the RUN2 mode, you  
will hear a chime. If the Console IS armed the Motion  
Detector will trip the alarm and sound the siren.  
1. Install four AA alkaline batteries in the battery  
compartment on the MS10A. Observe polarity.  
4. Set the slide switch on the back of the MS10A to 1 to  
trip the alarm if only one movement is detected (most  
sensitive). Set to 2 to trip the alarm only after 2  
movements are detected (helps prevent false alarms).  
4. Press the CODE button on the back of the MS10A  
with the point of a pencil.  
After you walk past the Motion Detector, it will not see  
motion again for about a minute (conserves battery power).  
Replacing batteries  
Slide the battery compartment cover off and replace the  
battery with a 9V alkaline type.After replacing the battery,  
the following steps are necessary to determine that the  
Console still recognizes the MS10A.  
5. Set the INSTALL/RUN switch on the Security  
Console to INSTALL.  
6. PressTEST on the MS10A.The Console emits a tone  
and the next unused zone indicator lights up.  
7. Set the Console's slide switch back toRUN1 orRUN2.  
8. To set up additional Motion Detectors (up to 16*)  
repeat the above steps.  
1. Place the Console’s slide switch to RUN2.  
2. Press TEST on the MS10A. If the Console chimes, it  
recognizes the MS10A and no further action is  
necessary.  
*Note: you can install a total of 16 zones in the Console.  
This can be a combination of Door/Window Sensors and  
Motion Detectors. E.G. 8 Door/Window Sensors AND 8  
Motion Detectors. See your Security System Owner’s  
Manual for more information.  
If the Console did not chime:  
1. Place the Console’s slide switch to INSTALL.  
2. PressTESTon the MS10A.The MS10A’s red indicator  
light flashes, and MS10A transmits a random code to  
the console.The Console acknowledges this with a beep  
and logs in the MS10A to the next available zone. To  
make sure the Console logs the MS10A back into the  
same zone it was allocated to before you changed the  
battery, wait 4 hours after removing the old battery  
before reinstalling (until the zone indicator on the  
Console starts flashing).  
X-10 (USA) INC. LIMITED 1-YEAR WARRANTY  
X-10 (USA) Inc. warrants X-10 products to be free from  
defective material and workmanship for a period of one (1)  
year from the original date of purchase at retail. X-10  
(USA)Inc.agreestorepairorreplace,atit’ssolediscretion,  
a defective X-10 product if returned to X-10 (USA) Inc.  
within the warranty period and with proof of purchase.  
P.I.R MOTION DETECTOR  
Operation  
When the Security System is armed using a Key Chain  
Remote the Motion Detector will always trip the alarm  
when it sees motion. When the system is armed using an  
SH624 Remote Control it can be armed in the Home or  
Away mode. When armed in the Home mode, Motion  
Detectors will NOT trip the alarm.  
If service is required under this warranty:  
1. Return the defective unit postage prepaid to X-10  
(USA) Inc. at the address below.  
2. Enclose a check for $4.00 to cover postage and  
handling.  
3. Enclose a dated proof of purchase.  
4. X-10 is not responsible for shipping damage.  
Place the Motion Detector on a bookshelf, or attach it to a  
wall about 6 feet off the ground, using the supplied  
mounting bracket. Wait about 45 seconds for the Motion  
Detector to settle then walk past it.  
X-10 (USA) Inc., 91 Ruckman Rd., Closter, NJ 07624. http://www.x10.com  
MS10A-998DR  
 

Weed Eater Trimmer 530163751 User Manual
Western Digital Computer Drive WD10EADS User Manual
Westinghouse Flat Panel Television LTV 32W3 User Manual
Westinghouse Outdoor Ceiling Fan UL ES Crusader WH09 User Manual
Whirlpool Air Conditioner ACPS82 User Manual
Whirlpool Microwave Oven W10249249A User Manual
Woodstock Sander W1678 User Manual
Yamaha Electronic Keyboard DC1516V User Manual
Zanussi Washer Dryer WDL 1282 User Manual
Zebra Technologies Printer Z4Mplus User Manual