THREE SPEED
ELECTRONIC WASHER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service call: 1-800-253-1301
In Canada, for assistance call: 1-800-461-5681,
for installation and service call: 1-800-807-6777
or visit our website at
Table of Contents.............................................................2
3953949B
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic
precautions, including the following:
ꢀꢀꢀRead all instructions before using the washer.
ꢀ
ꢀ
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is
used near children.
ꢀ
Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
discarded,
Before the washer is removed from service or
remove the door or lid.
ꢀ
ꢀ
Do not reach into the washer if the drum, tub or agitator
is moving.
ꢀꢀꢀDo not add gasoline, dry-cleaning solvents, or
other flammable, or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode.
Do not install or store the washer where it will be
exposed to the weather.
ꢀ
ꢀ
Do not tamper with controls.
ꢀ
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not
been used for such a period, before using the
washing machine, turn on all hot water faucets
and let the water flow from each for several
minutes. This will release any accumulated
hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
Do not repair or replace any part of the washer or
attempt any servicing unless specifically recommended
in this manual or in published user-repair instructions
that you understand and have the skills to carry out.
ꢀ
See “Electrical Requirements” for grounding instructions.
SAVE THESE INSTRUCTIONS
3
PARTS AND FEATURES
1. Control panel
7. Detergent dispenser
2. Model and serial number label
3. Liquid chlorine bleach dispenser
4. Liquid fabric softener dispenser
5. XTRA ROLL ACTION™ PLUS agitator
6. Lid
8. DURASMOOTH™ white porcelain basket
9. Tub
Additional features
CATALYST® cleaning action
ACCUWASH™ temperature control system
Control panel
4
Loading
WASHER USE
Loading suggestions
For these suggested full-sized loads, set the LOAD SIZE selector
to the highest setting.
Understanding Washer Cycles
SUPER CAPACITY PLUS WASHERS
When a cycle is selected, the washer lid is closed, and Start is
pushed, the washer fills (to the selected load size) before
agitation and timing start. The washer begins agitating
immediately after filling. If CATALYST® cleaning action is selected,
the washer spins and sprays detergent solution for a brief period
before filling with water.
Heavy Work Clothes
3 pair pants
3 shirts
1 coverall
1 overall
4 pair jeans
During agitation, the agitator creates a continuous rollover action
that provides a thorough cleaning of the wash load.
Delicates
3 camisoles
1 quilted robe
4 slips
6 undergarments
2 sets of sleepwear
1 child’s outfit
Towels
10 bath towels
10 hand towels
14 wash cloths
1 bath mat
Mixed Load
3 double sheets
4 pillowcases
8 T-shirts
NOTES:
2 shirts
ꢀ
The washer pauses briefly throughout each cycle. These
pauses are normal for washer operation.
2 blouses
8 handkerchiefs
6 pair shorts
ꢀ
Follow the progress of your wash cycle with the Washing
Status indicator lights.
WASH
RINSE
Normal Sounds
Your new washer may make sounds your old one didn’t. Because
the sounds might be unfamiliar, you may be concerned about
them. These sounds are normal.
1. Spin-Spray
(detergent
mixture)†
1. Fill
During washing
When you select a small load size setting, your washer has a
lower water level. This can cause a clicking sound from the upper
part of the agitator.
If you select CATALYST® cleaning action, you will hear a spin/
spray noise at the start of the cycle.
2. Fill
2. Rinse
3. Drain
3. Wash
selected
time
No agitation
During drain
If water is drained quickly from your washer (depending on your
installation), you may hear air being pulled through the pump
during the end of draining.
4. Drain
No agitation*
4. Spin-Spray
rinse
After drain and before spin
When the cycle changes from draining to spinning, you may hear
gears engaging.
5. Spin
5. Spin
6. Off
When selecting a cycle or an option
A tone sounds whenever a selection is made. The sound level of
the tones is not adjustable.
† When the CATALYST option is
selected, the washer spins and
sprays a detergent solution for a
brief period prior to filling.
ꢀ
A single tone sounds whenever a selection is accepted.
Three short tones sound if an unavailable selection is made.
ꢀ
* The Permanent Press/Casual
cycle partially drains, fills,
agitates briefly, and drains.
5
3. Pour measured liquid chlorine bleach into the liquid chlorine
bleach dispenser, if desired. Bleach is diluted and
automatically dispensed during the wash cycle. See “SMART
BLEACH™ Timed Bleach Dispenser.”
Starting Your Washer
ꢀ
Never use more than 1 cup (250 mL) for a full load. Use
less for a smaller load size.
Fire Hazard
ꢀ
ꢀ
Follow the manufacturer’s directions for safe use.
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
To avoid spilling, use a cup with a pouring spout. Do not
let bleach splash, drip, or run down into the washer
basket.
ꢀ
Use only liquid chlorine bleach in this dispenser.
No washer can completely remove oil.
4. Pour measured liquid fabric softener into the fabric softener
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
dispenser, if desired.
Doing so can result in death, explosion, or fire.
WARNING
ꢀ
Do not overfill. The dispenser holds 3 oz (94 mL), or a
standard capful of fabric softener.
ꢀ
ꢀ
ꢀ
The fabric softener is dispensed in the final rinse.
Do not spill or drip any fabric softener on the clothes.
Use only liquid fabric softener in this dispenser.
5. Close the washer lid.
6. Select a Cycle. The preset Soil Level, Load Size, and Water
Temperature for the selected cycle will glow. See “Selecting a
Cycle.”
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
ꢀ
The preset settings provide the recommended fabric care
for your selected cycle.
ꢀ
You can change the preset settings by pressing the
“Select” pad of each option until the desired setting
glows.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
1. Drop a load of sorted clothes loosely into the washer.
ꢀ
ꢀ
ꢀ
Load evenly to maintain washer balance. Mix large and
small items.
ꢀ
Your washer uses ACCUWASH™ temperature control
system. When you select a cycle, the washer selects the
recommended ACCUWASH setting for the type of fabric
and soils being washed. See “ACCUWASH Temperature
Control System.” For best fabric care, follow garment
label instructions. See the Temperature Guide for more
information.
Items should move easily through the wash water.
Overloading can cause poor cleaning.
To reduce wrinkling of permanent press clothes and some
synthetic knits, use a large load size to provide more
space (see step 6).
2. Pour measured powdered or liquid detergent into the
detergent dispenser.
6
10. Press Start. The wash cycle begins.The total cycle time (in
Temperature Guide
Water Temp
minutes) glows in the Estimated Time Remaining display.
Use For
Hot
111°F (44°C)
or above
Whites and pastels
Heavy soils
NOTE: If you do not press Start within 5 minutes of selecting
the cycle, the cycle and settings are automatically cancelled.
Warm
90°-110°F
(32°-43°C)
Bright colors
Moderate to light soils
Pausing or restarting your washer
To pause the washer at any time, press Pause/Cancel once.
Cold
70°-90°F
(21°-32°C)
Colors that bleed or fade
Light soils
NOTE: In wash water temperatures colder than 70ºF
(21ºC), detergents do not dissolve well. Soils can be difficult
to remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like balls on the
surface of garments).
To restart the washer and resume the wash cycle, press Start.
7. (OPTIONAL STEP) To select or cancel CATALYST® cleaning
action, press On/Off. To learn how CATALYST cleaning action
works, see “Selecting Options.”
Changing or Cancelling Cycles and Options
The cycles and options (CATALYST cleaning action, Soak, Rinse/
Spin or Spin) may be changed any time before Start is pressed. A
single short tone will sound when a selection is made. If an
unavailable combination is selected, three short tones will sound
and the last selection will not be accepted.
The options can be changed any time after Start is pressed and
before the start of the selected option. Follow the progress of
your wash cycle with the Washing Status indicator lights.
ꢀ
ꢀ
CATALYST cleaning action is pre-selected in the Heavy
Duty and Whitest Whites cycles. When these cycles are
selected, the CATALYST option light glows. If CATALYST
cleaning action is not desired, you may cancel any time
before Start is pressed.
CATALYST cleaning action is automatically added to the
Quick Wash and Hand Wash cycles to help ensure the
best cleaning results. The CATALYST option light does not
glow until after Start is pressed.
To change an option after the cycle has started
1. Press Pause/Cancel once.
2. Select the desired option.
3. Press Start to resume the cycle.
To cancel a cycle
NOTE: CATALYST cleaning action cannot be cancelled in
the Quick Wash and Hand Wash cycles.
The CATALYST option can be added to any wash cycle.
ꢀ
8. (OPTIONAL STEP) To add an extra Rinse and Spin or an extra
Spin only to a wash cycle, press On/Off until the desired
option glows.
1. Press Pause/Cancel twice.
2. Select desired wash cycle.
3. Select options.
4. Press Start to restart the washer at the beginning of the new
cycle.
To select a Rinse and Spin only or a Spin only, see “Selecting
Options.”
9. (OPTIONAL STEP) The End of Cycle Signal is helpful when
you are washing items that should be removed from the
washer as soon as the cycle ends.
Press the Bell to select a Softer or Louder signal or to turn the
End of Cycle Signal Off.
7
Normal
Use this 8-12 minute cycle for moderately soiled cottons and
linens. The cycle starts with high speed agitation for deep
cleaning, then automatically steps to a lower speed to help
ensure gentle fabric care. High spin speed shortens drying time.
The preset agitation time is 10 minutes.
Selecting a Cycle
This section describes the available wash cycles and will help
you make the best cycle selections for your wash loads. Each
cycle is designed for different types of fabric and soil levels.
Preset cycle settings provide the recommended fabric care for
your selected cycle.
Perm. Press/Casual
For improved fabric care at water levels below medium, the
washer automatically lowers the agitation speed. This change
takes place in all cycles except Extra Delicate and Hand Wash.
For most loads, use the soil level (agitation time) recommended in
the preset settings.
Use this 6-10 minute cycle for cleaning lightly to moderately
soiled casual business clothes, permanent press blends and
synthetic fabrics. The cycle uses low speed agitation for
thorough cleaning and gentle fabric care for your no-iron fabrics.
To minimize wrinkling, this cycle features a cool down rinse and a
low-speed final spin. The preset agitation time is 8 minutes.
ꢀ
ꢀ
ꢀ
Select more time for heavy soils and sturdy fabrics.
Select less time for light soils and delicate fabrics.
Quick Wash
The washer pauses briefly throughout each cycle. These
pauses are normal. Refer to “Normal Sounds” to learn more
about the sounds you may hear during a wash cycle.
Use this 4-8 minute cycle for small, lightly soiled loads that need
refreshing. CATALYST cleaning action is automatically added to
this cycle to help ensure the best cleaning results. For the fastest
cycle, select a small load size and less soil level. The preset
agitation time is 6 minutes.
ꢀ
Refer to “Understanding Washer Cycles” to learn what
happens during a wash cycle.
Extra Delicate
Use this 4-8 minute wash cycle for sheer fabrics and lingerie. The
cycle features extra low speed agitation followed by a deep rinse
and a low speed spin. The preset agitation time is 6 minutes.
Hand Wash
Use this 4-8 minute cycle for hand washable garments. The cycle
features a series of brief, low speed agitations and short soaks to
gently clean special-care items. CATALYST cleaning action is
automatically added to this cycle to help ensure the best cleaning
results. Low spin speeds minimize wrinkling. The preset
agitation/soak time is 6 minutes.
NOTE: Wash small loads. If items appear to be floating (due to
trapped air), pause the washer by pressing Pause/Cancel once.
Push items down into the washer. Press Start.
Heavy Duty
Favorite Cycle
Use this 10-15 minute wash cycle for sturdy, colorfast fabrics
such as work clothes. The cycle combines high speed agitation
and high speed spin, to shorten drying times. This cycle also
includes CATALYST® cleaning action to help ensure removal of
heavy soils and stains. The preset agitation time is 15 minutes.
Favorite Cycle allows you to customize a favorite cycle and store
it for future use.
To store a Favorite Cycle
1. Select a cycle. If desired, change the preset cycle settings.
2. Select options.
Whitest Whites
3. Press and hold the Heart about 2 seconds until it beeps and
Use this 10-15 minute wash cycle for loads of white fabrics that
need improved whitening. The cycle combines high speed
agitation and high speed spin, to shorten drying times. This cycle
also includes CATALYST cleaning action, hot wash water and an
automatic second rinse. Bleach is recommended in this cycle to
provide outstanding whitening. The preset agitation time is
12 minutes.
the Favorite Cycle light glows.
4. Press Start.
To reuse Favorite Cycle
1. Press the Heart.
2. Press Start.
8
To select or cancel CATALYST cleaning action
Preset cycle settings
Your washer has preset soil levels, load sizes and water
temperatures based on the cycle selected. The preset settings
provide the recommended fabric care for your load. See chart.
Press On/Off to select or cancel CATALYST cleaning action. The
CATALYST option must be selected or cancelled before Start is
pressed.
Cycle
Soil Level
Load Size
Water
Temperature
Heavy Duty
More
Super Plus
Super Plus
Warm/Cold
Hot/Cold
Whitest
Whites
Normal
Soak
Normal
Normal
Normal
Super Plus
Super Plus
Warm/Cold
Warm/Cold
Use Soak for heavy soils and stains that need additional time for
removal. You can add Soak to a wash cycle, or you can select a
Soak only.
Perm. Press/
Casual
Quick Wash
Extra Delicate
Hand Wash
Soak
Normal
Normal
Normal
Normal
None
Medium
Warm/Warm
Warm/Cold
Cold/Cold
Medium
Medium
To add Soak to a wash cycle
Super Plus
Super Plus
Warm/Cold
Warm/Cold
When Soak is added to a wash cycle, the washer fills to the
selected water level, agitates briefly and soaks for a few minutes
before the wash cycle begins. The amount of soak time varies
with each cycle, but is not longer than 12 minutes.
Rinse/Spin
To change the preset cycle settings
1. Select a cycle.
Press the Select pad of each setting until the desired setting
glows.
2. Press On/Off until the Soak light glows.
3. Press Start.
To select a Soak only
Selecting Options
When a Soak only is selected, the washer fills to the selected
water level, agitates briefly and soaks. The preset soak time is 30
minutes. If a different soil level is selected, the soak time
increases or decreases, depending on the selection. After
soaking, the washer agitates briefly, drains and spins. Soak only
should be followed by a wash cycle, as there is no rinse.
You can customize your wash cycle by adding one or more of the
following options to your wash: CATALYST® cleaning action,
Soak, Rinse/Spin or Spin.
ꢀ
A single tone sounds when a selection is accepted.
ꢀ
Three short tones sound if an unavailable selection is made.
1. Place a sorted load of clothes into the washer. Add detergent
to the detergent dispenser.
®
CATALYST Cleaning Action
2. Press On/Off until the Soak light glows. The preset settings
Your washer uses CATALYST cleaning action to help ensure
better soil and stain removal from your wash load. CATALYST
cleaning action reduces the need for pretreatment and is safe for
all fabrics. CATALYST cleaning action is pre-selected in the
Heavy Duty and Whitest Whites cycles and is automatically
added to the Quick Wash and Hand Wash cyles. The CATALYST
option can be added to any wash cycle.
will glow. If desired, change settings.
3. Close washer lid. Press Start.
How CATALYST cleaning action works
1. Before agitation begins, detergent is automatically released
into a special chamber that mixes the detergent with a small
amount of water to create a sudsy cleaning solution.
2. Spinning spreads out the clothes.
3. The cleaning solution showers onto the top of the fabrics. The
solution is pulled through the clothes, and the detergent
enzymes attach to soils and stains, lifting them away.
4. A sensor alerts the washer when the cleaning solution
completely penetrates the stains and soils and a rich, sudsy
lather covers the clothes. The washer fills to the selected
water level and completes the selected cycle.
NOTES:
ꢀ
For best results, the load should be dry at the start of the
cycle.
ꢀ
Stubborn and set-in stains might require additional
pretreatment.
9
Rinse/Spin or Spin only
When using extra detergent for heavily soiled clothes, or washing
special-care items, you may find an extra rinse and spin is
needed. The Rinse/Spin option may also be used for items that
need rinsing only or for completing a cycle after a power failure.
SMART BLEACH™ Timed Bleach Dispenser
The timed bleach dispenser automatically dispenses liquid
chlorine bleach to the wash load at the appropriate time during
the cycle to help ensure the cleanest and brightest loads. Bleach
is dispensed into the wash load a few minutes after agitation
begins in order to give the detergent time to achieve the best soil
and stain removal.
An extra drain and spin may help shorten drying times for some
heavy fabrics or special-care items by removing excess water.
The Spin option may also be used for draining the washer after
canceling a cycle or completing a cycle after a power failure.
NOTE: Do not use this dispenser to add powdered chlorine or
color-safe bleach to your wash load. The dispenser is for liquid
chlorine bleach only.
Self-Cleaning Lint Filter
Your washer has a self-cleaning lint filter at the bottom of the
basket. Wash and rinse water flow over the filter during agitation,
separating the lint from the water. The lint spins out of the system
during the spin part of the cycle. If your washer drains into a tub,
remove any lint collected in the tub or strainer.
To add an extra Rinse/Spin or Spin to a cycle
1. Select a cycle.
2. Press On/Off until the light glows for the desired option.
3. Press Start.
To select a Rinse/Spin or a Spin only
1. Place a load of clothes into the washer.
2. Press On/Off until the light glows for the desired option.
3. Press Start.
WASHER CARE
Cleaning Your Washer
Cleaning the exterior
Use a soft, damp cloth or sponge to wipe up any spills such as
detergent or bleach. Occasionally wipe the outside of your
washer to keep it looking new.
ACCUWASH™ Temperature Control System
Your washer uses ACCUWASH temperature control system. The
ACCUWASH feature maintains a uniform water temperature by
regulating incoming hot and cold water. This helps eliminate
undissolved detergent and ensures consistent cleaning results.
The cold wash is regulated at approximately 75ºF (24ºC). The
warm wash is maintained at approximately 100ºF (38ºC).
Cleaning the interior
When you select a cycle, the washer selects the recommended
ACCUWASH setting for the type of fabric and soils being
washed.
Clean your washer interior by mixing 1 cup (250 mL) of chlorine
bleach and 2 cups (500 mL) of detergent. Pour this into your
washer and run it through a complete cycle using hot water.
Repeat this process if necessary.
NOTES:
NOTE: Remove any hard water deposits using only cleaners
labeled as washer safe.
ꢀ
Make sure that both hot and cold water faucets are turned on
or the ACCUWASH feature will not work properly.
ꢀ
The wash and rinse water temperature for Hot/Cold are not
regulated with the ACCUWASH feature.
Cleaning the dispensers
The dispensers are self-cleaning. If the liquid fabric softener
dispenser needs cleaning, scrub with a brush using a liquid
laundry detergent solution.
The ACCUWASH feature can be turned Off by pressing On/Off.
IMPORTANT:
ꢀ
Remove hard water deposits using only cleaners labeled as
washer safe.
ꢀ
Never use any cleaning fluids on dispenser parts. This can
cause damage to the plastic.
10
Water Inlet Hoses
TROUBLESHOOTING
Replace inlet hoses after five years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
First try the solutions suggested here and possibly avoid
the cost of a service call...
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
Washer displaying code message
ꢀ
“LF” (Long Fill)
Are the water inlet hoses kinked or clogged?
Vacation, Storage,
and Moving Care
Are the water inlet valve screens clear?
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
ꢀ
ꢀ
“LD” (Long Drain)
Is the drain hose kinked or clogged?
“FF” (Fill Failure)
There is a problem with the water level sensing system. Call
for service.
Non-use or vacation care
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
ꢀ
ꢀ
ꢀ
“OL” (Open Lid)
Is the lid open?
ꢀ
Unplug washer or disconnect power.
“OB” (Off Balance)
Is the load unbalanced? Redistribute the load.
ꢀ
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
“F” Variables (F1, F2, ...F9)
A washer operation failure has occurred. Do the following:
To winterize washer
1. Press Pause/Cancel twice.
1. Shut off both water faucets.
2. Open and close the washer lid.
3. Reset the cycle and press Start.
2. Disconnect and drain water inlet hoses.
If the problem persists, press Pause/Cancel twice to clear the
display. Call for service.
3. Put 1 quart (1 L) of R.V.-type antifreeze in the basket.
4. Run washer on a drain and spin setting (see “Selecting
Options”) for about 30 seconds to mix the antifreeze and
water.
Washer won’t fill, rinse or agitate
5. Unplug washer or disconnect power.
ꢀ
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
To use washer again
1. Flush water pipes and hoses.
Is there power at the plug? Check electrical source or call
electrician.
2. Reconnect water inlet hoses.
3. Turn on both water faucets.
4. Plug in washer or reconnect power.
Are the water inlet valve screens clogged?
Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
5. Run the washer through a complete cycle with 1 cup (250 mL)
of detergent to clean out antifreeze.
Is there oversudsing? Spin load; restart cycle. Do not add
detergent.
ꢀ
Does the water level seem too low, or does the washer
appear to not fill completely?
The top of the agitator is much higher than the highest water
level. This creates a perception that the washer is not filling
completely. This is normal.
Washer stops
ꢀ
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Did you press Pause/Cancel? To restart the washer, press
Start.
Are the water inlet valve screens clogged?
Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
ꢀ
Is there power at the plug?
Check electrical source or call electrician.
11
ꢀ
ꢀ
ꢀ
Has a fuse blown or has the circuit breaker tripped?
If problem continues, call electrician.
Washer leaks
Are you using an extension cord?
Do not use an extension cord.
ꢀ
Check the following:
Are the fill hoses tight? Are the fill hose washers properly
seated? Is the drain hose clamp properly installed? See the
Installation Instructions.
Is the washer in a normal pause in the Perm. Press/
Casual or Hand Wash cycle?
The washer pauses for about 2 minutes in the Perm. Press/
Casual cycle. Allow the cycle to continue.
ꢀ
ꢀ
Is the sink or drain clogged?
Sink and standpipe must be able to handle 17 gal. (64 L) of
water per minute.
The Hand Wash cycle features periods of agitation and soak.
ꢀ
ꢀ
Is the washer overloaded?
Wash smaller loads.
Is water deflecting off the tub ring or the load?
Center the tub before starting the washer.
The wash load should be balanced and not overloaded. The
fill or spray rinses can deflect off the load.
Washer won’t drain or spin
Is the drain hose clogged, or the end of the drain hose
more than 96 in. (244 cm) above the floor?
See the Installation Instructions for proper installation of drain
hose.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
ꢀ
Check household plumbing for leaks.
ꢀ
ꢀ
Is the lid open?
The lid must be closed during operation.
Washer basket is crooked
Is there excessive sudsing?
ꢀ
ꢀ
Was the washer basket pulled forward during loading?
The wash load should be balanced and not overloaded. Push
the basket to the center before starting wash.
Always measure detergent. Follow manufacturer’s directions.
If you have very soft water, you might need to use less
detergent.
Is the load balanced and the washer level?
The wash load should be balanced and not overloaded.
ꢀ
Is your voltage low?
Check electrical source or call electrician. Do not use an
extension cord.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
Washer continues to fill or drain, or the cycle seems stuck
ꢀ
ꢀ
The washer basket moves while washing.
This is normal.
ꢀ
ꢀ
Is the top of drain hose lower than the water level in
washer?
The top of the hose must be higher than the water level in the
washer for proper operation. See the Installation Instructions.
Agitator operation
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. See the
Installation Instructions.
The top of the agitator is loose, or moves in only one
direction.
This is normal.
Dispensers clogged or bleach leaking
Washer makes noise
ꢀ
ꢀ
Did you follow the manufacturer’s directions when adding
detergent and fabric softener to the dispensers?
Measure detergent and fabric softener. Carefully pour into the
dispensers. Wipe up all spills.
ꢀ
Is the load balanced and the washer level?
The wash load should be balanced and not overloaded.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
Dilute fabric softener in the fabric softener dispenser.
Did you put powdered or liquid, color-safe bleach in the
liquid chlorine bleach dispenser?
Add powdered or liquid color-safe bleach to the detergent
dispenser. Do not use the chlorine bleach dispenser for color-
safe bleach.
Did you completely remove the yellow shipping strap with
cotter pins? See the Installation Instructions.
ꢀ
Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash?
These are normal washer noises.
Load too wet
ꢀ
ꢀ
Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed.
Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. This is
normal.
12
Residue or lint on load
Gray whites, dingy colors
ꢀ
ꢀ
ꢀ
Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
ꢀ
ꢀ
ꢀ
Did you properly sort the load?
Dye transfer can occur when mixing whites and colors in a
load. Sort dark clothes from whites and lights.
Did you overload the washer?
The wash load must be balanced and not overloaded. Lint
can be trapped in the load if overloaded. Wash smaller loads.
Was the wash temperature too low?
Use hot or warm washes if safe for the load. Hot water should
be at least 111°F (44°C) to clean heavy soils.
Check the following:
Was paper or tissue left in pockets?
Did you use enough detergent, or do you have hard
water?
Use more detergent for washing heavy soils in cold or hard
water.
Did you use enough detergent? Follow manufacturer’s
directions. Use enough detergent to hold the lint in the water.
ꢀ
ꢀ
Are the hot and cold water hoses reversed?
Check to be sure the hot and cold water hoses are connected
to the right faucets. See the Installation Instructions.
Is your water colder than 70°F (21°C)? Wash water colder
than 70°F (21°C) may not completely dissolve the detergent.
Stains on load
Garment damage
ꢀ
ꢀ
Did you follow the manufacturer’s directions when adding
detergent and fabric softener?
Measure detergent and fabric softener. Use enough detergent
to remove soil and hold it in suspension.
Check the following:
Were sharp items removed from pockets before washing?
Empty pockets, zip zippers, snap or hook fasteners before
washing.
Did you add fabric softener directly to the load? Use your
fabric softener dispenser, if available. Do not drip fabric
softener on clothes.
Were strings and sashes tied to prevent tangling?
Were items damaged before washing? Mend rips and broken
threads in seams before washing.
ꢀ
ꢀ
ꢀ
Is there above average iron (rust) in water?
You may need to install an iron filter.
ꢀ
ꢀ
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
Did you properly sort the load?
Sort dark clothes from whites and lights.
Did you unload the washer promptly?
Did you properly add chlorine bleach?
To avoid dye transfer, unload the washer as soon as it stops.
Do not pour chlorine bleach directly on load. Use your liquid
chlorine bleach dispenser, if available. Wipe up bleach spills.
Undiluted bleach will damage fabrics.
Load is wrinkled
ꢀ
Did you follow the manufacturer’s care label instructions?
ꢀ
ꢀ
Did you unload the washer promptly?
Unload the washer as soon as it stops.
Did you use the right cycle for the load being washed?
Use the Perm. Press/Casual cycle or another cycle with a low
spin speed to reduce wrinkling.
ꢀ
ꢀ
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
Was the wash water warm enough to relax wrinkles, or
are you using warm rinses?
If safe for the load, use warm or hot wash water. Use cold
rinse water.
ꢀ
Are the hot and cold water hoses reversed?
Check to be sure the hot and cold water hoses are connected
to the right faucets. See the Installation Instructions.
Load is tangled or twisted
ꢀ
ꢀ
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
Did you wrap items around the agitator?
Drop items loosely into the washer. Do not wrap items around
the agitator.
13
In Canada
ASSISTANCE OR SERVICE
Call the Whirlpool Canada Inc. Customer Interaction Center toll
free:
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
1-800-461-5681 8:30 a.m. - 5:30 p.m. EST.
Our consultants provide assistance with:
ꢀ
Features and specifications on our full line of appliances
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help Whirlpool Assistance or Service to better respond to your
request.
ꢀ
Referrals to local dealers
For service in Canada
Call 1-800-807-6777. Whirlpool Canada Inc. designated service
technicians are trained to fulfill the product warranty and provide
after-warranty service anywhere in Canada.
If you need replacement parts
If you need to order replacement parts, Whirlpool recommends
that you only use FSP® factory specified parts. These parts will fit
right and work right because they are made with the same
precision used to build every new WHIRLPOOL GOLD®
appliance.
For further assistance
If you need further assistance, you can write to Whirlpool Canada
Inc. with any questions or concerns at:
To locate FSP® replacement parts in your area:
Customer Interaction Center
Whirlpool Canada Inc.
1901 Minnesota Court
In the U.S.A., call the Customer Interaction Center at
1-800-253-1301, or your nearest Whirlpool designated service
center.
Mississauga, Ontario L5N 3A7
In Canada, call 1-800-807-6777, or your nearest Whirlpool
designated service center.
Please include a daytime phone number in your correspondence.
Gearcase assembly covered by your warranty
In the U.S.A.
Call the Whirlpool Customer Interaction Center toll free:
1-800-253-1301.
Our consultants provide assistance with:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Features and specifications on our full line of appliances
Installation information
Use and maintenance procedures
Accessory and repair parts sales
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
ꢀ
Referrals to local dealers, repair parts distributors, and
service companies
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service anywhere in
the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Brand Home Appliances
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
14
WHIRLPOOL GOLD® WASHER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this washer is operated and maintained according to instructions attached to or furnished with
the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or workmanship. Service
must be provided by a Whirlpool designated service company.
FIVE-YEAR LIMITED WARRANTY ON TOP, LID, GEARCASE ASSEMBLY AND ELECTRONIC CONTROL BOARD
For five years from the date of purchase, when this washer is operated and maintained according to instructions attached to or furnished with
the product, Whirlpool Corporation will pay for FSP® replacement parts for the following, if defective in materials or workmanship: porcelain top
and lid (against chipping and rust); any part of the gearcase assembly; the electronic control board.
TEN-YEAR LIMITED WARRANTY ON OUTER TUB
For ten years from the date of purchase, when this washer is operated and maintained according to instructions attached to or furnished with
the product, Whirlpool Corporation will pay for FSP® replacement parts for the outer tub should it crack or fail to contain water, if defective in
materials or workmanship.
LIFETIME LIMITED WARRANTY ON WHITE PORCELAIN BASKET
For the lifetime of the washer, when this washer is operated and maintained according to instructions attached to or furnished with the product,
®
Whirlpool Corporation will pay for FSP replacement parts for the white porcelain basket should it chip or rust due to defects in materials or
workmanship.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your washer, to instruct you how to use your washer, or to replace house fuses or correct house
wiring or plumbing.
2. Repairs when your washer is used in other than normal, single-family household use.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with
local electrical and plumbing codes, or use of products not approved by Whirlpool Corporation.
4. Any labor costs during the limited warranty periods.
5. Replacement parts or repair labor costs for units operated outside the United States and Canada.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. In Canada, travel or transportation expenses for customers who reside in remote areas.
WHIRLPOOL CORPORATION AND WHIRLPOOL CANADA INC.
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Outside the 50 United States and Canada, this warranty does not
apply. Contact your authorized Whirlpool dealer to determine if
another warranty applies.
Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages, so this exclusion or limitation
may not apply to you. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state or
province to province.
If you need service, first see “Troubleshooting.” Additional help can
be found by checking “Assistance or Service,” or call our Customer
Interaction Center at 1-800-253-1301 from anywhere in the U.S.A. or
write: Whirlpool Corporation, Customer Interaction Center, 553
Benson Road, Benton Harbor, MI 49022-2692. In Canada, call
Whirlpool Canada Inc. at 1-800-807-6777.
4/00
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Keep this book and your sales slip together for future reference.
You must provide proof of purchase or installation date for in-
warranty service.
Write down the following information about your washer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number. You
can find this information on the model and serial number label/plate,
located on your appliance as shown in “Parts and Features.”
3953949B
© 2002 Whirlpool Corporation.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.,
Whirlpool Canada Inc. Licensee in Canada
1/02
Printed in U.S.A.
|