Model No. 831.150290
Serial No.
Write the serial number in the
space above for reference.
WEIGHT BENCH EXERCISER
User’s Manual
Serial Number Decal (under seat)
• Assembly
• Adjustments
• Troubleshooting
• Part List and Drawing
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
10. The weight bench is designed to support a
maximum user weight of 300 pounds, and a
maximum total weight of 410 pounds. Do not
place more than 110 pounds, including a bar-
bell and weights, on the weight rests. Do not
place more than 50 pounds on the leg lever.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
11. Always be sure there is an equal amount of
weight on each side of your barbell when
you are using it. Always keep some weight
on both ends of the barbell when adding or
removing weights to prevent the barbell from
tipping.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Use the weight bench only on a level sur-
face. Cover the floor beneath the weight
bench to protect the floor.
12. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
5. Make sure all parts are properly tightened
each time the weight bench is used. Replace
any worn parts immediately.
13. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
6. Keep children under 12 and pets away from
the weight bench at all times.
7. Always wear athletic shoes for foot protec-
tion while exercising.
14. When using the backrest in an inclined posi-
tion, make sure that the support rod is
inserted completely through both uprights,
and that the support rod is turned to the
locked position.
8. Keep hands and feet away from moving
parts.
9. Do not use a barbell that is longer than six
feet with the weight bench. Note: The weight
bench does not include a barbell or weights.
15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® PRO
reading this manual, call 1-800-4-MY-HOME®
220 weight bench. The weight bench offers an impres- (1-800-469-4663). To help us assist you, please note
sive array of weight stations designed to develop
every major muscle group of the body. Whether your
goal is to tone your body, build dramatic muscle size
and strength, or improve your cardiovascular system,
the weight bench will help you to achieve the specific
results you want.
the product model number and serial number before
calling. The model number is 831.150290. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
ASSEMBLED
DIMENSIONS:
Height: 47 in.
Width: 30 in.
Depth: 62 in.
Weight Rests
Upright
Backrest
Support Rod
Seat
Leg Lever
Weight Tube
4
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part, from the PART LIST on page 14 of this manual. Important:
Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts
bags, check to see if it has been pre-assembled. If a part is missing, call toll-free 1-800-999-3756.
50mm Square
Inner Cap (16)
25mm Round Angle Cap (17)
M4 x 16mm Screw (29)
38mm Square
Inner Cap (18)
25mm Round Inner Cap (20)
M6 x 16mm Screw (24)
M10 x 50mm Bolt (28)
19mm Round Inner Cap (21)
M10 x 60mm Bolt (25)
25mm Square Inner Cap (19)
M6 Washer (22)
M10 x 60mm Carriage Bolt (26)
M10 Washer (30)
M10 Nylon Locknut (31)
M10 x 68mm Bolt (27)
M10 x 142mm Bolt (23)
5
ASSEMBLY
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by anyone. However, it is important to
realize that the versatile weight bench has many
parts and that the assembly process will take
time. Most people find that by setting aside plen-
ty of time, assembly will go smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two people.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Before assembling the weight bench, be sure
that you have read and understand the infor-
mation in the box above.
1
16
Press three 50mm Square Inner Caps (16) into
the Upright (1) without the warning decal.
1
Attach two Joint Plates (11) to the Upright (1) with
two M10 x 68mm Bolts (27) and two M10 Nylon
Locknuts (31). Do not tighten the Locknuts yet.
Warning
Decal
Repeat this step with the other Upright (1).
Make sure the Joint Plates (11) are oriented as
shown in the inset drawing.
11
31
11
27
16
1
16
6
2. Attach the Crossbar (2) to an Upright (1) with two
M10 x 68mm Bolts (27), two Joint Plates (11),
and two M10 Nylon Locknuts (31). Do not tight-
en the Locknuts yet.
2
Repeat this step with the other Upright (1).
1
1
31
11
27
2
3. Press three 50mm Square Inner Caps (16) into
the Front Leg (4) and the Stabilizer (5).
3
16
31
Attach the Front Leg (4) to the Stabilizer (5) with
two M10 x 60mm Carriage Bolts (26) and two
M10 Nylon Locknuts (31). Do not tighten the
Locknuts yet.
4
31
16
5
16
26
4. Attach the Front Leg (4) to the Bench Frame (3)
with two M10 x 50mm Bolts (28), two M10
Washers (30), and two M10 Nylon Locknuts (31).
Do not tighten the Locknuts yet. Make sure
the bolt heads fit inside the hexagon holes in
the Bench Frame.
4
31
30
3
30
28
4
Hexagon
Holes
7
5. Attach the Bench Frame (3) to the Crossbar (2)
with two M10 x 68mm Bolts (27) and two M10
Nylon Locknuts (31).
5
27
2
Tighten the M10 Nylon Locknuts (31) used in
steps 1–5.
3
31
6. Press a 25mm Round Inner Cap (20) into the indi-
cated end of the weight tube on the Leg Lever
(6). Press a 25mm Round Angled Cap (17) onto
the other end of the weight tube.
6
31
Tap two 38mm Square Inner Caps (18) into the
Leg Lever (6).
18
25
4
6
Lubricate the M10 x 60mm Bolt (25) with grease.
Attach the Leg Lever (6) to the Front Leg (4) with
the Bolt and an M10 Nylon Locknut (31). Do not
overtighten the Locknut; the Leg Lever must
be able to pivot easily.
17
Lubricate
20
18
6
7. Press two 25mm Square Inner Caps (19) into a
Pad Tube (12). Slide the Pad Tube into the Leg
Lever (6). Slide two Foam Pads (13) onto the
ends of the Pad Tube. Make sure the Foam
Pads are oriented as shown.
7
13
19
12
Repeat this step with the other Pad Tube (12).
19
13
12
8. Press a 25mm Round Inner Cap (20) into a
Weight Rest (15). Insert the Weight Rest into an
Upright (1). Turn the Weight Rest so the locking
pin is wrapped around the Upright.
8
15
Repeat this step with the other Weight Rest
(15).
Locking
Pin
20
1
15
8
9. Press two 19mm Round Inner Cap (21) into the
Support Rod (14). Insert the Support Rod into a
set of holes in the Uprights (1). Turn the Support
Rod so the locking pin is wrapped around the
Upright.
9
14
21
1
Locking
Pin
21
10. Press four 25mm Square Inner Caps (19) into the
two Backrest Tubes (7).
10
8
Attach the Backrest Tubes (7) to the Backrest (8)
with four M6 x 38mm Screws (32) and four M6
Washers (22). Do not tighten the Screws yet.
19
22
7
22
19
32
32
11. Lubricate an M10 x 142mm Bolt (23) with grease.
Attach the Backrest Tubes (7) to the welded tube
on the Bench Frame (3) with the Bolt, two M10
Washers (30), and an M10 Nylon Locknut (31).
Do not overtighten the Locknut; the Backrest
Tubes must be able to pivot easily.
11
30
31
Tighten the M6 x 38mm Screws (32) used in
step 10.
7
3
30
23
Lubricate
Tube
9
12. Attach the Seat (9) to the Bench Frame (3) with
four M6 x 16mm Screws (24).
12
3
13. Make sure that all parts are properly tightened
before you use the weight bench. The use of
all remaining parts will be explained in ADJUST-
MENTS, beginning on the following page.
24
24
9
ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information
and refer to the accompanying exercise guide to see the correct form for each exercise. Refer also to the
exercise information accompanying your weight set for additional exercises.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
1
The Backrest (8) can be used in a decline position, a
level position, or two incline positions. To use the
Backrest in the decline position, remove the Support
Rod (14) and lay the Backrest on the Crossbar (2).
1
To use the Backrest (8) in the level position, lift the
Backrest and insert the Support Rod (14) through the
bottom set of holes in the Uprights (1). Rotate the
locking pin into place around the Upright.
8
14
To use the Backrest (8) in an incline position, lift the
Backrest and insert the Support Rod (14) through an
upper set of holes in the Uprights (1). Rotate the lock-
ing pin into place around the Upright.
WARNING:
When using the
2
Backrest (8) in a level or incline position,
insert the Support Rod (14) completely
through both Uprights (1) and turn it to the
locked position.
6
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (6), slide the desired weights
(not included) onto the weight tube.
Weight
Tube
WARNING:
Do not place more
than 50 pounds on the Leg Lever (6).
Weight
ADJUSTING THE WEIGHT RESTS
To change the weight of the Weight Rests (15),
remove the them from the Uprights (1) and insert them
into the desired set of holes. Rotate the Weight Rests
so that the locking pins wrap around the Uprights.
15
Locking
Pin
Locking
Pin
15
1
WARNING:
Always set both
Weight Rests (15) at the same height.
1
10
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
ing it during the first few months of your exercise pro-
gram. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
right for you. Begin with 3 sets of 8 repetitions for each your body for more strenuous exercise by increasing
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-
erate percentage of their capacity. Select a moderate
amount of resistance and increase the number of rep-
etitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by com-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
pleting more sets rather than by using high amounts of Schedule your workouts for the time of day when your
resistance.
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
Cross Training
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an exercise bike,
on Tuesday and Thursday.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
• Rest from both strength training and aerobic exercise The repetitions in each set should be performed
for at least one full day each week to give your body
time to regenerate.
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
The combination of strength training and aerobic exer-
cise will reshape and strengthen your body, plus devel- during the return stroke. Never hold your breath.
op your heart and lungs.
11
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on page 13 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the resistance
used, and the numbers of sets and repetitions com-
pleted. Record your weight and key body measure-
ments at the end of every month. Remember, the key
to achieving the greatest results is to make exercise a
regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
B
Q
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
C
D
E
R
S
T
F
M
N
U
G
H
I
V
W
X
J
K
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
12
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
13
PART LIST—Model No. 831.150290
R0803A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2
1
1
1
1
1
2
1
1
2
4
2
4
1
2
9
1
2
Upright
Crossbar
Bench Frame
Front Leg
Stabilizer
Leg Lever
Backrest Tube
Backrest
Seat
Upright Cover
Joint Plate
19
20
21
22
23
24
25
26
27
28
29
30
31
32
#
8
3
2
4
1
4
1
2
10
2
4
4
16
4
1
25mm Square Inner Cap
25mm Round Inner Cap
19mm Round Inner Cap
M6 Washer
M10 x 142mm Bolt
M6 x 16mm Screw
M10 x 60mm Bolt
M10 x 60mm Carriage Bolt
M10 x 68mm Bolt
M10 x 50mm Bolt
M4 x 16mm Screw
M10 Washer
M10 Nylon Locknut
M6 x 38mm Screw
User’s Manual
Pad Tube
Foam Pad
Support Rod
Weight Rest
50mm Square Inner Cap
25mm Round Angled Cap
38mm Square Inner Cap
#
#
1
1
Exercise Guide
Grease Pack
“#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
this manual for information on ordering replacement parts.
14
EXPLODED DRAWING—Model No. 831.150290
R0803A
8
16
19
29
15
21
7
31
30
19
22
23
20
10
29
7
32
14
22
30
21
16
32
31
10
29
15
1
16
11
20
31
29
11
2
11
11
16
13
13
19
19
27
27
12
12
9
19
27
16
13
13
1
16
31
30
19
3
31
16
4
31
25
18
24
28
24
6
17
31
20
31
18
16
5
16
26
15
WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States
and Sears will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for
rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Part No. 199258 R0803A
Printed in China © 2003 Sears, Roebuck and Co.
|