R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
FeatherLitet LE
FeatherLitetPlus LE
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
530163077
3/19/02
Copyright E2002 Electrolux Home Products, Inc.
CUTTING SAFETY
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your right to your left. Cutting on left
side of the shield will throw debris away from
the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbure-
tor by starting the engine and letting it run until
it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the 50 hours of use, we recommend that your
tube.
muffler be serviced or replaced by your autho-
rized service dealer.
S Store unit out of reach of children.
ASSEMBLY
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section. Assemble your shield as shown.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
4. Securely tighten wing nut onto bolt.
ADJUSTING THE HANDLE
Slot
Shield
WARNING: When adjusting the han-
dle, be sure it remains between the trigger
and the safety label.
Bracket
1. Loosen wing nut on handle.
2. Rotate the handle on the tube to an upright
position; retighten wing nut.
Wing
Nut
ATTACHING SHIELD
Line Limiter Blade
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
3
OPERATION
KNOW YOUR TRIMMER
REOUR UNIT.
Corious controls
and
Assist Handle
Tube
Trimmer
Head
Throttle
Trigger
Muffler
ON/OFF
Switch
Spark Plug
Choke Lever
Primer Bulb
Starter
Handle
Shield
Line
Limiter
Blade
Fuel Mix
Fill Cap
ON/STOP SWITCH
CHOKE
The ON/STOP switch is used to stop engine. To
stop the engine, push and release the engine
ON/STOP switch.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
read and follow the safety rules relating to fuel
before fueling your unit.
BEFORE STARTING ENGINE
IMPORTANT
WARNING: Be sure to read the fuel
information in the safety rules before you
begin. If you do not understand the safety
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
rules, do not attempt to fuel your unit. Call methanol) can attract moisture which leads to
1-800-554-6723.
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage.
FUELING ENGINE
To avoid engine problems, empty the fuel sys-
tem before storage for 30 days or longer.
Drain the gas tank, start the engine and let it
run until the fuel lines and carburetor are
empty. Use fresh fuel next season.
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/Weed Eater brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 ounces of oil with 1 gallon of
unleaded gasoline. DO NOT USE automotive
oil or boat oil. These oils will cause engine
damage. When mixing fuel, follow instructions
printed on container. Once oil is added to
gasoline, shake container momentarily to
assure that the fuel is thoroughly mixed. Always
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage may
occur. See the STORAGE section for addi-
tional information.
HOW TO STOP YOUR UNIT
S To stop the engine, push and release the
engine ON/STOP switch. The switch will
automatically return to the ON position.
Wait 5 seconds before attempting to restart
unit to allow switch to reset.
S If engine does not stop, move choke to the
FULL CHOKE position.
4
flooded. Proceed to STARTING
FLOODED ENGINE.
8. Once the engine starts, allow it to run 10
seconds, then move the choke lever to the
OFF CHOKE position. Allow the unit to run
for 30 more seconds at OFF CHOKE be-
fore releasing the throttle trigger.
A
Engine
ON/STOP
Switch
Choke Lever
HALF
FULL
OFF
NOTE: If engine dies with the choke lever
in the OFF CHOKE position, move the
choke lever to the HALF CHOKE position
and pull the rope until engine runs, but no
more than 6 pulls.
HOW TO START YOUR UNIT
STARTING A WARM ENGINE
1. Move the choke lever to the HALF CHOKE
position.
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
2. Squeeze and hold the throttle trigger. Keep
throttle trigger fully squeezed until the engine
runs smoothly.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
3. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
4. Allow engine to run 15 seconds, then move
the choke lever to OFF CHOKE.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
Starting Position
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE posi-
tion.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
Starter Handle
Choke
Lever
OPERATING POSITION
ALWAYS WEAR:
Eye Protection
Muffler
Long Pants
Primer Bulb
Heavy Shoes
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not pull
rope more than 6 times.
Cut from your right to your left.
6. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL CHOKE
position and press the primer bulb 6 times.
Squeeze and hold the throttle trigger and
pull the starter rope 2 more times. Move
the choke lever to the HALF CHOKE posi-
tion and pull the starter rope until the en-
gine runs, but no more than 6 pulls. If the Always release the throttle trigger and allow the
engine still doesn’t start, it is probably engine to return to idle speed when not cutting.
5
To stop engine:
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch.
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
in. (5 cm) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
S For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
The most efficient line length is the maximum
length allowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
To advance line:
S Operate the engine at full throttle.
S Hold the trimmer head parallel to and above
the grassy area.
Trimming
S Tap the bottom of the trimmer head lightly
on the ground one time. Approximately 2 in.
(5 cm) of line will be advanced with each
tap.
3 in. (8 cm)
Above Ground
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient line length.
SCALPING -- The scalping technique re-
moves unwanted vegetationdown to the
ground. Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground and at an
angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
WARNING: Use only 0.065” (2 mm)
diameter line. Other sizes and shapes of line
will not advance properly and will result in im-
proper cutting head function or can cause se-
rious injury. Do not use other materials such
as wire, string, rope, etc. Wire can break off
during cutting and become a dangerous mis-
sile that can cause serious injury.
Scalping
CUTTING METHODS
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Mowing
Tip of the Line
Line Crowded Into
Does The Cutting Work Area
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
Wrong
Swee
S The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4--5 in. (10--13 cm) and use
at less than full throttle.
6
MAINTENANCE
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
3. Wash the filter in soap and water.
4. Allow filter to dry.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Assist Handle Screws
S Debris Shield
5. Add a few drops of oil to the filter; squeeze
the filter to distribute oil.
6. Replace parts.
er
Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by pushing and
releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
Air Filter Cover
MUFFLER AND SPARK ARREST-
ING SCREEN
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire haz-
ard or affecting engine performance.
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recom-
mend that your muffler be serviced or re-
placed by your authorized service dealer.
INSPECT AND CLEAN UNIT AND
LABELS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed and nonadjustable.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and 1. Twist, then pull off spark plug boot.
harmful emissions. Always clean after every
5 hours of operation.
2. Remove spark plug from cylinder and dis-
card.
1. Clean the cover and the area around it to 3. Replace with Champion RCJ-6Y spark plug
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
and tighten securely with a 3/4 inch socket
wrench.
4. Reinstall the spark plug boot.
7
SERVICE AND ADJUSTMENTS
5. Wind the line evenly and tightly onto the
LINE REPLACEMENT
spool. Wind in the direction of the arrow
found on the spool.
1. Remove spool by firmly pulling on tap button.
2. Clean entire surface of hub and spool.
3. Replace with pre--wound spool, or cut a
length of 20 feet of 0.080! (2 mm) diameter
Weed Eaterr brand line.
6. Push the line into the notche, leaving 3 to 5
inches (7 -- 12 cm) unwound.
7. Insert the line into the the exit holebin the hub
as shown in the illustration.
8. Align the notch with the line exit hole.
9. Push spool into hub until it snaps into place.
10.Pull the line extending outside of the hub to
release it from the notch.
CARBURETOR ADJUSTMENT
Your carburetor is equipped with limiter caps.
Carburetor adjustment is a complicated task.
We recommend that you take your unit to an
authorized service dealer. Damage will occur
if you turn the needles beyond the limiter
stops.
WARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
4. Insert one end of the line about 1/2 inch (1
cm) into the small hole on the inside of spool.
Small
Hole
Spool
Line in Notch
Line exit hole
STORAGE
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
S Lightly oil external metal surfaces.
FUEL SYSTEM
OTHER
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la- S Do not store gasoline from one season to
beled IMPORTANT regarding the use of ga-
sohol in your engine.
another.
S Replace your gasoline can if it starts to rust.
8
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. See “Carburetor Adjustment” in
Service and Adjustments Section.
5. Carburetor requires
adjustment.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
and regap.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
1. Adjust choke.
smokes
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. See “Carburetor Adjustment” in
Service and Adjustments Section.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
9
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
not cover predelivery setup or normal
warrants to the original purchaser that each new adjustments explained in the instruction manual.
Weed Eaterr brand gasoline tool or attachment
is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES
EXCEPT
THOSE
EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
30 DAYS -- Parts and Labor, if used for rental WARRANTY LASTS OR THE EXCLUSION
purposes.
OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically The policy of ELECTROLUX HOME
recommended by ELECTROLUX HOME
PRODUCTS, INC., is to continuously improve
PRODUCTS, INC., for this tool. Additionally, its products. Therefore, ELECTROLUX HOME
this warranty does not cover tune--ups, spark
PRODUCTS, INC., reserves the right to
plugs, filters, starter ropes, starter springs, change, modify, or discontinue models,
cutting line, or rotating head parts that will wear designs, specifications, and accessories of all
and require replacement with reasonable use products at any time without notice or obligation
during the warranty period. This warranty does to any purchaser.
U.S. EPA/CALIFORNIA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
your small off--road engine, but POULAN/
TIONS: The U.S. Environmental Protection WEED EATER cannot deny warranty solely for
Agency/California Air Resources Board and the lack of receipts or for your failure to ensure
POULAN/WEED EATER, DIVISION OF WCI
OUTDOOR PRODUCTS are pleased to ex-
the performance of all scheduled maintenance.
As the small off--road engine engine owner, you
plain the emissions control system warranty on should be aware that POULAN/WEED EATER
your year 2000--2003 small off--road engine. In may deny you warranty coverage if your small
California, all new small off--road engines must off--road engine engine or a part of it has failed
be designed, built, and equipped to meet the due to abuse, neglect, improper maintenance,
State’s stringent anti--smog standards. POU- unapproved modifications, or the use of parts
LAN/WEED EATER must warrant the emission not made or approved by the original equipment
control system on your small off--road engine for manufacturer. You are responsible for present-
the periods of time listed below provided there ing your small off--road engine to a POULAN/
has been no abuse, neglect, or improper main- WEED EATER authorized repair center as
tenance of your small off--road engine engine. soon as a problem exists. Warranty repairs
Your emission control system includes parts should be completed in a reasonable amount of
such as the carburetor and the ignition system. time, not to exceed 30 days. If you have any
Where a warrantable condition exists, POU- questions regarding your warranty rights and re-
LAN/WEED EATER will repair your small off-- sponsibilities, you should contact your nearest
road engine engine at no cost to you. Expenses authorized service center or call POULAN/
covered under warranty include diagnosis, WEED EATER at 1--800--554--6723. WAR-
parts and labor. MANUFACTURER’S WAR-
RANTY COVERAGE: If any emissions related
RANTY COMMENCEMENT DATE: The war-
ranty period begins on the date the small
part on your engine (as listed under Emissions off--road engine is purchased. LENGTH OF
Control Warranty Parts List) is defective or a de- COVERAGE: This warranty shall be for a peri-
fect in the materials or workmanship of the en- od of two years from the initial date of purchase.
gine causes the failure of such an emission re- WHAT IS COVERED: REPAIR OR RE-
lated part, the part will be repaired or replaced PLACEMENT OF PARTS. Repair or replace-
by POULAN/WEED EATER.
OWNER’S
ment of any warranted part will be performed at
no charge to the owner at an approved POU-
WARRANTY RESPONSIBILITIES: As the
small off--road engine engine owner, you are re- LAN/WEED EATER servicing center. If you
sponsible for the performance of the required have any questions regarding your warranty
maintenance listed in your instruction manual. rights and responsibilities, you should contact
POULAN/WEED EATER recommends that
your nearest authorized service center or call
you retain all receipts covering maintenance on POULAN/WEED EATER at 1--800--554--6723
10
WARRANTY PERIOD: Any warranted part
failures of warranted parts caused by the use of
which is not scheduled for replacement as re- add--on or modified parts. HOW TO FILE A
quired maintenance, or which is scheduled only CLAIM: If you have any questions regarding
for regular inspection to the effect of “repair or your warranty rights and responsibilities, you
replace as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
should contact your nearest authorized service
center or call POULAN/WEED EATER at
for replacement as required maintenance shall 1--800--554--6723. WHERE TO GET WAR-
be warranted for the period of time up to the first RANTY SERVICE: Warranty services or re-
scheduled replacement point for that part. pairs shall be provided at all POULAN/WEED
DIAGNOSIS: The owner shall not be charged
EATER service centers. call: 1--800--554--6723
for diagnostic labor which leads to the deter- MAINTENANCE, REPLACEMENT AND RE-
mination that a warranted part is defective if the PAIR OF EMISSION RELATED PARTS: Any
diagnostic work is performed at an approved POULAN/WEED EATER approved replace-
POULAN/WEED EATER servicing center.
CONSEQUENTIAL DAMAGES: POULAN/
ment part used in the performance of any war-
ranty maintenance or repair on emission related
WEED EATER may be liable for damages to parts will be provided without charge to the own-
other engine components caused by the failure er if the part is under warranty. EMISSION
of a warranted part still under warranty. WHAT CONTROL WARRANTY PARTS LIST: Car-
IS NOT COVERED: All failures caused by
buretor, Ignition System: Spark Plug (covered
abuse, neglect, or improper maintenance are up to maintenance schedule), Ignition Module,
not covered. ADD--ON OR MODIFIED
Muffler including catalyst. MAINTENANCE
PARTS: The use of add--on or modified parts STATEMENT: The owner is responsible for the
can be grounds for disallowing a warranty claim. performance of all required maintenance as de-
POULAN/WEED EATER is not liable to cover fined in the instruction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
11
|