R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
FL1500 LE
For Household Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
WEED EATER
1030 Stevens Creek Road
Augusta, GA 30907
545137215 11/30/06
D Empty the fuel tank before storing the unit.
Use up fuel left in carburetor by starting the
engine and letting it run until it stops.
D Do not use any accessory or attachment
other than those recommended by the
manufacturer for use with your unit.
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped witha spark arresting screen. If you
operatein alocalewhere such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler beservicedor replacedby your autho-
rized service dealer.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from water heaters, electric mo-
tors or switches, furnaces, etc.
D Store in a dry area out of reach of children.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has beenlinked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti- vibration system
ASSEMBLY
NOTE: It is normal for the fuel filter to rattle in
BLOWER TUBE
the empty fuel tank.
D
Push the blower tube into the blower out-
let until it snaps into place.
ASSEMBLY
Blower Outlet
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Follow all safety information in the manual
and on the unit.
D
No tools are required for assembly.
Blower Tube
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with locations of the various
controls and adjustments. Save this manual for future reference.
Fuel Cap
Primer Bulb
Throttle Lever
Blower Tube
Choke
Lever
-- 3 --
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
THROTTLE LEVER
The throttle lever is used to select the desired
engine speed and to stop the engine. To stop
engine, move the throttle lever to the STOP
position.
CHOKE LEVER
TheCHOKE helps tosupply fuelto the engine
to aid in cold starting. The CHOKE OFF posi-
tion is used for full speed operation. The 1/2
position is used for a brief initial warm-up peri-
od and to set the engine at idle speed.
PRIMER BULB
The PRIMER BULB removes air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
OPERATING POSITION
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2 -cycle synthetic oil into
one gallon of fresh gas.
tion
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/WEED EATER
brand synthetic oil is recommended. Mix gaso-
line and oil at a ratio of 40:1. A 40:1ratio is ob-
tainedby mixing3.2ounces (95ml) of oil with 1
gallon (4 liters) of unleaded gasoline. DO NOT
USE automotive oil or boat oil. These oils will
cause engine damage. When mixing fuel, fol-
low instructions printed on container. Once oil
is added to gasoline, shake container mo-
mentarily to assure that the fuel is thoroughly
mixed. Always read and follow the safety
rules relating to fuel before fueling your unit.
OPERATING TIPS
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S Use rakes and brooms to loosen debris be-
fore blowing.
S In dusty conditions, slightly dampen sur-
faces when water is available.
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watchout for children, pets, openwindows,
or freshly washed cars. Blow debris away
safely.
S Use the full blower tube extension so the air
stream can work close to the ground.
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
TO STOP THE ENGINE
D To stop the engine, move the throttle lever
to the STOP position.
STARTING YOUR ENGINE
WARNING: You MUST make sure
the tube is secure before using the unit.
D Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fuel your unit. Call
1-800-554-6723.
-- 4 --
4. Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls.
5. Move choke lever to 1/2 CHOKE. Pull
starter rope sharply until engine runs.
NOTE: If engine has not started after 5 pulls,
repeat all of the above steps.
G
N
6. After a 10 second warm-up, move the
choke lever to CHOKE OFF.
NOTE:Move throttle lever to the
position
for low speed.
7. To stop engine, move the throttle lever to
the STOP position.
WARNING: When starting engine,
hold the unit as illustrated. Do not set unit on
any surface except a clean, hard area when
starting engine or while engine is running.
Debris such as gravel, sand, dust, grass, etc.
could be picked up by the air intake and
thrown out through the discharge opening,
damaging the unit or property, or causing
serious injury to bystanders or the operator.
NOTE: If engine does not stop, move choke
lever to FULL CHOKE.
STARTING A WARM ENGINE
1. Move throttle lever to the
position.
2. Move the choke lever to the CHOKE OFF
position.
3. Pull starter handle sharply until engine
runs.
NOTE: If engine does not run after 5 pulls,
repeat STARTING A COLD ENGINE proce-
dure.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1-800-554 -6723.
DIFFICULT STARTING (or starting a
flooded engine)
Flooded engines can be started by placing the
choke lever in the CHOKE OFF position and the
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
throttle lever to the
position; then, pull the
starter handle sharply to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly the
unit is flooded. If the unit still does not start, refer
to TROUBLESHOOTING TABLE or call
1-800-554-6723.
1. Move throttle lever to the
position.
2. Move choke lever to the FULL CHOKE
position.
3. Slowly press the primer bulb 6 times.
Primer
Bulb
Throttle
Choke Lever
Lever
MAINTENANCE
We recommend all maintenance, service and
adjustments not listed in this manual be per-
formed by an authorized service dealer.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, WEED EATER may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
-- 5 --
1. Clean the cover and the area around it to
keep debris from falling into the carbure-
tor chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
3. Wash the filter in soap and water.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
S Air Filter
S Housing Screws
CHECK FOR DAMAGED OR
WORN PARTS
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Throttle Lever -- Ensure throttle lever func-
tions properly by moving the throttle lever to
the STOP position. Make sure engine
stops; then restart engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
INSPECT AND CLEAN UNIT AND
DECALS
4. Reinstall the spark plug boot.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit us-
ing a damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
WARNING: The muffler on this
product contains chemicals known to the
State of California to cause cancer.
CLEAN AIR FILTER
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire haz-
ard or affecting engine performance.
Air Filter
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recom-
mend that your muffler be serviced or re-
placed by your authorized service dealer.
CARBURETOR ADJUSTMENTS
There is no screw for idle adjustment on your
blower. The throttle lever is used to control
engine speed. The throttle lever can be
placed in one of four positions: STOP, IDLE
Screw
Air Filter Cover
or
, FULL THROTTLE or
, and one
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
intermittent position. If your enginewill not run
properly or you require further assistance,
contact an authorized service dealer or call
1--800--554--6723.
STORAGE
SEASONAL STORAGE
WARNING: Perform the following
steps after each use:
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.If your
unit is to be stored for a period of time:
S Clean the entire unit before lengthy stor-
age.
S Allow engine to cool, and secure the unit
before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
S Store unit and fuel well out of the reach of
children.
-- 6 --
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel
tank or fuel storage container. Follow the mix
instructions found on stabilizer container. Run
engine at least 5 minutes after adding stabilizer.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
HELPFUL TIP
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
1. Engine flooded.
REMEDY
1. See “Starting a Flooded Engine”
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
5. Compression low.
1. Fuel not reaching
1. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Engine will not
idle properly.
carburetor.
2. Carburetor requires
adjustment.
3. Crankshaft seals worn.
4. Compression low.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer
4. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Air filter dirty.
2. Fuel not reaching
carburetor.
Engine will not
accelerate,
lacks power, or
dies under a
load.
3. Clean or replace spark plug
and re-gap.
3. Spark plug fouled.
4. Contact an authorized service dealer.
4. Carburetor requires
adjustment.
5. Carbon build up.
6. Compression low.
5. Contact an authorized service dealer.
6. Contact an authorized service dealer.
1. Choke partially on.
1. Adjust choke.
Engine smokes
excessively.
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs hot.
1. See “Fueling Engine” in Operation
section.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
4. Carbon build up.
-- 7 --
LIMITED WARRANTY
WEED EATER warrants to the original pur-
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
chaser that each new WEED EATER brand
gasoline tool or attachment is free from defects
in material and workmanship and agrees to re-
pair or replace under this warranty any defective
gasoline product or attachment as follows from
the original date of purchase.
2 YEARS--Parts and Labor, when used for
household purposes.
90 DAYS--Parts and Labor, when used for com-
mercial, professional, or income producing pur-
poses.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of WEED EATER is to continuously
improve its products. Therefore, WEED EATER
reserves the right to change, modify, or discon-
tinue models, designs, specifications, and ac-
cessories of all products at any time without no-
tice or obligation to any purchaser.
30 DAYS--Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by WEED EATER for this tool.
Additionally, this warranty does not cover tune-
ups, spark plugs, filters, etc., that will wear and
require replacement with reasonable use during
the warranty period. This warranty does not
cover predelivery setup or normal adjustments
explained in the instruction manual.
U.S. EPA/CALIFORNIA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency/California Air Resources
Board and WEED EATER are pleased to ex-
plain the emissions control system warranty
on your year 2007 and later small off--road en-
gine. In California, all small off--road engines
must bedesigned, built, andequipped to meet
the State’s stringent anti--smog standards.
WEED EATER must warrant the emission
control system on your small off--road engine
for the periods of time listed below provided
there has been no abuse, neglect, or improp-
er maintenance of your small off--roadengine.
Your emission control system includes parts
such as the carburetor, the ignition system and
the fuel tank (California only). Where a warrant-
able condition exists, WEED EATER will re-
pair your small off--road engine engine at no
cost to you. Expenses covered under warran-
ty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions relatedpart onyour
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of suchan emissionrelated
part, the part will be repaired or replaced by
WEED EATER. OWNER’S WARRANTY
RESPONSIBILITIES: As the small off--road
engine engine owner, you are responsible for
the performance of the required maintenance
listed in your instruction manual. WEED EATER
recommends that you retain all receipts cover-
ing maintenance on your small off--road en-
gine, but WEED EATER cannot deny warran-
ty solely for the lack of receipts or for your fail-
ure to ensure the performance of all sched-
uled maintenance. As the small off--road en-
gine engine owner, you should be aware that
WEED EATER may deny you warranty cov-
erage if your small off--road engine engine or
a part of it has failed due to abuse, neglect, im-
proper maintenance, unapproved modifica-
tions, or the use of parts not made or ap-
proved by the original equipment manufactur-
er. You are responsible for presenting your
small off--road engine to a WEED EATER au-
thorized repair center as soon as a problem
exists. Warranty repairs should be completed
in a reasonable amount of time, not to exceed
30 days. If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized ser-
vice center or call WEED EATER at
1--800--554--6723. WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off--road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years from the initial date of purchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved WEED
EATER servicing center. If you have any
questions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized service center or call
WEED EATER at 1--800--554--6723. WAR-
RANTY PERIOD: Any warranted part which
is not scheduled for replacement as required
maintenance, or which is scheduled only for
regular inspection to the effect of “repair or re-
-- 8 --
place as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
for replacement as required maintenance
shall be warranted for the period of time up to
the first scheduled replacement point for that
part. DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is de-
fective if the diagnostic work is performed at
an approved WEED EATER servicing center.
CONSEQUENTIAL DAMAGES: WEED
EATER may be liable for damages to other
engine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD -ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. WEED EATER is not liableto cover fail-
ures of warranted parts caused by the use of
add--on or modified parts. HOW TO FILE A
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized ser-
vice center or call WEED EATER at
1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all WEED EATER
service centers. Call 1--800--554--6723.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION RELATED PARTS:
Any WEED EATER approved replacement
part used in the performance of any warranty
maintenance or repair on emission related
parts will be provided without charge to the
owner if the part is under warranty. EMIS-
SION CONTROL WARRANTY PARTS
LIST: Carburetor, Ignition System: Spark
Plug (covered up to maintenance schedule),
Ignition Module, Muffler including Catalyst,
Fuel Tank (California only). MAINTENANCE
STATEMENT: The owner is responsible for
the performance of all required maintenance
as defined in the instruction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 9 --
|