R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
EBV VS
FOR HOUSEHOLD USE ONLY
PARA USO CASERO SOLAMENTE
POUR UTILISATION À DES FINS
DOMESTIQUES SEULEMENT
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
WEED EATER
1030 Stevens Creek Road
Augusta, GA 30907
WEED EATER
5855 Terry Fox Way
Mississauga, Ontario L5V 3E4
545117528
8/8/06
let only one way. If plug does not fit fully
into the wall outlet, reverse the plug. If it
still does not fit, contact a qualified electri-
cian to install the proper wall outlet. Do not
change the equipment plug, extension
cord receptacle, or extension cord plug in
any way.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help pro-
tect against electric shock. Double insula-
tion construction consists of two separate
“layers” of electrical insulation instead of
grounding. Tools and appliances built with
a double insulation system are not in-
tended to be grounded. No grounding
means is provided on this unit, nor should
a means of grounding be added to this
unit. As a result, the extension cord used
with your unit can be plugged into any
standard 120 volt electrical outlet. Safety
precautions must be observed when op-
erating any electrical tool. The double in-
sulation system only provides added pro-
tection against injury resulting from an
internal electrical insulation failure.
STo reduce the risk of electrical shock, use
extension cords specifically marked as
suitable for outdoor appliances. The elec-
trical rating of the cord must not be less
than the rating of the unit. The cord must
be marked with the suffix “W-A” (in Cana-
da, “W”). Make sure your extension cord
is in good condition. Inspect extension
cord before use and replace if damaged.
An undersized extension cord will cause
a drop in line voltage resulting in loss of
power and overheating. If in doubt, use
the next heavier gauge. The smaller the
gauge number, the heavier the cord.
(NOTE: The correct size to be used de-
pending on the cord length is shown in
this manual. See SELECT AN EXTENSION
CORD in the ASSEMBLY section).
S Do not use multiple cords.
S Keep the extension cord clear of operator
and obstacles at all times.
S Tie cord to cord retainer and connect to
recessed plug as shown in this manual to
prevent damage to unit and/or extension
cord and to reduce the possibility of the
extension cord disconnecting from the
unit during operation.
S Do not attempt to repair unit. Inspect the
insulation and connectors on the unit
and extension cord before each use. If
there is any damage, do not use until
damage is repaired by your authorized
service dealer.
S Do not use the unit if the switch does not
turn the unit on and off properly. Have the
unit repaired by your authorized service
dealer.
S Avoid accidental starting. Be sure the
switch is in the OFF position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit con-
nected to the power source.
S Avoid any body contact with any
grounded conductor, such as metal
fences, or pipes, to avoid the possibility of
electric shock.
WARNING:
All electrical repairs to this unit, including
housing, switch, motor, etc., must be diag-
nosed and repaired by qualified service
personnel. Replacement parts for
a
double insulated appliance must be iden-
tical to the parts they replace. A double in-
sulated appliance is marked with the
words “double insulation” or “double insu-
lated”. The symbol
(square within a
square) may also be marked on the ap-
pliance. Failure to have the unit repaired
by an authorized service dealer can
cause the double insulation construction
to become ineffective and result in serious
injury.
UNIT/MAINTENANCE SAFETY
S Do not set the unit on any surface ex-
cept a clean, hard area while the unit is
running. Debris such as gravel, sand,
dust, grass, etc., could be picked up by
the air intake and thrown out through the
discharge opening, damaging the unit,
property, or causing serious injury to by-
standers or operator.
S Do not overreach or use from unstable
surfaces such as ladders, trees, steep
slopes, rooftops, etc. Use extra care
when cleaning on stairways. Keep firm
footing and balance at all times. Keep
hands out of tubes.
S Inspect the entire unit before each use
for worn, loose, missing, or damaged
parts. Do not use until the unit is in
proper working order.
S This unit is double insulated. See the
DOUBLE INSULATION CONSTRUCTION
section. Have all internal service per-
formed by qualified service repair per-
sonnel to avoid creating a hazard or
voiding your warranty.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the cir-
cuit or outlet to be used for this unit. Re-
ceptacles are available having built-in
GFCI protection and may be used for this
measure of safety.
S Stop the motor immediately if you are ap-
proached.
3
S Have all maintenance other than the VACUUM SAFETY
recommended procedures described in
the instruction manual performed by
your authorized service dealer.
S Stop the motor and disconnect the pow-
er source before opening the air inlet
door or attempting to insert or remove
the vacuum tubes. The motor must be
stopped and the impeller blades no
longer turning to avoid serious injury
from the rotating blades.
S Always see your authorized service
dealer to replace a damaged impeller.
Parts that are chipped, cracked, broken,
or damaged in any other way can fly
apart and cause serious injury. Replace
damaged parts before using the unit.
S Never place any object in the air intake
opening as this could restrict proper air
flow and cause damage to the unit.
S Never douse the unit with water or other
liquids or squirt with a water hose. Clean
the unit using a damp cloth. Wipe off
with a clean dry cloth. See MAINTE-
NANCE.
S Hard objects can be thrown through the
collection bag or the housing and be-
come dangerous missiles which can
cause serious injury to the operator or
others.
S When using the vacuum attachment, the
unit is designed to pick up dry material
such as leaves, grass, small twigs, and
bits of paper. Do not vacuum stones,
gravel, metal, broken glass, etc., to avoid
severe damage to the impeller. To avoid
the possibility of electrical shock, do not
attempt to vacuum water or other liquids.
S Never run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes and
collection bag assembly. Make sure the
collection bag assembly is completely
zipped when unit is running to avoid flying
debris. Use only recommended attach-
ments.
S Avoid situations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits, brush
piles, etc. To avoid spreading fire, do not
use blower near leaf or brush fires, fire-
places, barbecue pits, ashtrays, etc.
S Always use the collection bag shoulder
strap when vacuuming to avoid loss of
control.
S Check air intake openings and tubes
frequently, always with the unit stopped
and power source disconnected. Keep
vents and tubes free of debris which can
accumulate and restrict proper air flow.
S Do not burn, incinerate, or expose this
unit to extreme heat.
S Store the unit unplugged in a high, cool,
dry, indoor area out of the reach of chil-
dren.
S Use only recommended attachments
and replacement parts to avoid creating
a hazard and/or voiding warranty.
S Maintain the unit according to recom-
mended procedures.
S Use only for jobs explained in the OP-
ERATION section of this manual.
BLOWER SAFETY
S Use only in daylight or in good artificial
light.
S Inspect the area before using the unit.
Remove all debris and hard objects
such as rocks, glass, wire, etc., that can
ricochet, be thrown, or otherwise cause
injury or damage during operation.
S Never run the unit without the proper
equipment attached. When used as a
blower, always install a blower tube. Use
only recommended attachments.
S To avoid spreading fire, do not use blow-
er near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
S Check air intake openings, elbow tube,
and vacuum tubes frequently, always with
the unit stopped and the power source
disconnected. Keep vents and tubes free
of debris which can accumulate and re-
strict proper air flow. Do not use with any
opening blocked, Keep free of dust, lint,
hair and anything that may reduce air
flow.
CAUTION: To avoid causing damage to
the unit, DO NOT attempt to use the vari-
able speed control during vacuum use.
S Never place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automo-
biles, walls, etc. The force of air can
cause rocks, dirt, or sticks to be thrown
or to ricochet which can hurt people or
animals, break glass, or cause other
damage.
STANDARDS
This product is listed by Underwriters Lab-
oratories, Inc., in accordance with UL
Standard 1017.
If situations occur which are not covered
in this manual, use care and good judg-
ment. If you need assistance, contact
your authorized service dealer or call
1--800--554--6723. Failure to follow all
Safety Rules and Precautions can result
in serious injury.
S Never use for spreading chemicals, fer-
tilizers, or any other substances which
may contain toxic materials.
4
SAVE THESE INSTRUCTIONS
ASSEMBLY
1. Ensure unit is stopped and extension
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover or attempting to in-
sert or remove the inlet restrictor, blower
tube, or vacuum tubes. The motor must
be stopped and the impeller blades no
longer turning to avoid serious injury from
the rotating blades.
cord is unplugged.
2. Open the inlet cover by inserting the
tip of a screwdriver into the latch area
on the blower unit. Gently tilt handle
of screwdriver toward the front of the
unit to release the latch while pulling
up on the vacuum inlet cover with
your other hand.
Bottom view
Latch Area
of unit
WARNING: If received assembled,
ensure your unit is properly assembled
and all fasteners are secure.
S A standard screwdriver is required for
assembly.
BLOWER ASSEMBLY
NOTE: Assembly instructions for using
your unit as a vacuum follow this section.
Vacuum Inlet Cover (closed)
Impeller
Attaching the blower tube
h Area
If you have already assembled your unit
for use as a vacuum, refer to the section
HOW TO CONVERT UNIT FROM VAC-
UUM USE TO BLOWER USE.
To attach blower tube:
1. Align the grooves on the blower tube
with the grooves on the bloweroutlet.
2. Push the blower tube onto theblower
outlet until it snaps into place (tube is
secured by red tube release button).
3. To remove the blower tube, press the
tube release button while pulling on
tube.
Vacuum Inlet Cover (opened)
3. Turn the inlet restrictor counterclock-
wise and remove it from the unit. Do
not close the inlet door. You will next
attach the vacuum tubes.
Vacuum
Inlet Cover
Tube Release Button
Blower Tube
Inlet
Restrtr
Blower outlet
VACUUM ASSEMBLY
Attaching the vacuum tubes
NOTE: Assembly instructions for using
your unit as ablower areexplained inthe
previous section.
There are 2 vacuum tubes, an upper
tube and a lower tube. The upper tube
has a vacuum assist handle attached to
one end and is cut straight on both ends.
The upper tube attaches to the blower
unit. The lower tube has an angled end
that you point toward the ground during
vacuum use. The lower tube attaches to
the upper tube.
If you have already assembled your unit
for use as a blower, remove the blower
tube.
CAUTION: To avoid causing damage to
the unit, DO NOT attempt to use the vari-
able speed control during vacuum use.
Remove the inlet restrictor
1. Ensure unit is stopped and exten-
sion cord is unplugged.
An inlet restrictor is used when using your
unit as a blower. This restrictor is not used
during vacuum use and must be removed
during assembly for vacuum use.
2. While holding inlet cover open, place
the hooks of the vacuum assist handle
on the retaining posts of the unit.
NOTE: Be sure to keep the inlet re-
strictor for using your unit as a blower.
3. Raise the tube until it is secured to the
blower unit by the red inlet cover latch.
5
Upper Vacuum Tube
Vacuum Assist Handle
Last In
First In
Hook
2. Position the unit on your right-hand
side, blower outlet and bag pointing
toward the rear. Hold the unit in an
upright position with the lower vacu-
um tube on the ground to support it.
3. Place the shoulder strap over your
head and onto your left shoulder.
4. Adjust the strap to allow a free flow of
air from the blower. If the collection
bag is kinked, the unitwill notoperate
properly.
Retaining Post
4. To attach the lower vacuum tube to
the upper vacuum tube, first align the
arrows on the two tubes. Then, press
the two tubes together until the lower
tube is securely seated in the upper
tube (about 3 inches).
NOTE: The strap is designed to posi-
tion the collection bag on your shoulder
without kinks. The strap is not intended
to support the weight of the unit.
Upper Tube
Lower Tube
Align arrows on upper
and lower tubes
Shoulder strap
on left shoulder
COLLECTION BAG ASSEMBLY
1. Open the zipper on the collection
bag and insert the elbow tube.
2. Push the small end of the elbow tube
through the small opening in the bag.
NOTE: Make sure edge of the small
opening is flush against the flared area
of the elbow tube and the hole for the
tube release button is on top.
No kinks in bag
allows free air flow
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Stop unit and unplug the extension
cord.
2. Remove the vacuum tubes by insert-
ing the tip of a screwdriver into the
latch area on the vacuum assist han-
dle. Gently tilt handle of screwdriver
toward the front of the unit to release
the latch while pulling up on the vacu-
um assist handle with your other hand.
Tube
Elbow Tube
Release
Button
Hole
Zipper
Opening
Small
Opening
3. Close the zipper on the bag. Make
sure the zipper is closed completely.
4. Align the grooves on the elbow tube
with the grooves on the bloweroutlet.
5. Push the elbow tube onto the blower
outlet until it snaps into place (elbow
tube is secured by red tube release
button).
Vacuum
Assist
Handle
ADJUSTING THE SHOULDERSTRAP
ON THE COLLECTION BAG
1. Carefully loop the shoulder strap
through the buckle as shown in the il-
lustration below.
3. Install the inlet restrictor that was re-
moved when assembling forvacuum
use.
6
NOTE: If you are unable to locate the
inlet restrictor, the unit will still operate.
This restrictor improves the blower
function.
4. Remove the collection bag.
5. Close the inlet cover and make sure
it is latched closed.
6. Re-install the blower tube. Refer to AT-
TACHING THE BLOWER TUBE for
instructions on how to attach this item.
SELECT AN EXTENSION CORD
Use only a 120 A.C. voltage supply as
shown on nameplate of the unit to
power your blower.
The extension cord used to reach the
power source must be:
MINIMUM WIRE GAUGE
RECOMMENDATIONS
VOLTS
120
25 FT.
50 FT.
100 FT.
16
A.W.G.*
16
A.W.G.*
14
A.W.G.*
*American Wire Gauge
Secure the extension cord to the unit by
threading the cord through the cord re-
tainer (see illustration). Insert the cord
receptacle into the recessed plug.
CAUTION: Failure to use cord retain-
er could result in damage to the unit,
extension cord, or both.
D Specifically marked as suitable for out-
door use. The cord mustbe marked with
the suffix “W-A” (in Canada “W”).
D Heavy enough to carry full current from
the power source to the unit. Otherwise,
loss of power and overheating can oc-
cur causing damage to unit. Refer to
table for minimum wire gauge recom-
mendations. The cord must be marked
with the proper wire gauge. (Appropriate
extension cords are available.) Do not
use multiple cords.
D In good condition. Cord insulation must
be intact with no cracks or deterioration.
Plug connectors must be undamaged.
DO NOT use multiple cords.
Cor
Rec
sed
lug
Unit
Co
Re
7
USING YOUR UNIT
KNOW YOUR ELECTRIC BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations to your unit to familiarize yourself with the location of
the various controls and adjustments. Save this manual for future reference.
ON/OFF Switch
Variable Speed Control
Collection Bag
Air Vents
Cord
Retainer
Elbow
Tube
Upper Vacuum Tube
Retaining Post
Rear
Handle
Inlet Cover
Latch
Va
Upper Va
Tube Release Button
Blower Tube
Lowe
Inlet Restrictor
ON/OFF SWITCH
TUBE RELEASE BUTTON
The ON/OFF SWITCH is used to activate
The TUBE RELEASE BUTTON secures the
blower tube or elbow tube to the blower
unit during operation. Also, pressing the
tube release button allows removal of the
blower tube or elbow tube.
the motor.
INLET COVER LATCH
The INLET COVER LATCH is used toopen
and close the inlet cover and to secure
the upper vacuum tube to the blower
unit.
VARIABLE SPEED CONTROL
The VARIABLE SPEED CONTROL is de-
signed to allow an increase or decrease
in motor speed as necessary during
blower use only. To avoid causing dam-
age to the unit, DO NOT attempt to use
the variable speed control during vacu-
um use.
BLOWER TUBE
The BLOWER TUBE is designed to direct
the flow of air.
INLET RESTRICTOR
The INLET RESTRICTOR improves the
blower function.
SWITCH POSITIONS
WARNING: You MUST make sure
the tubes are secure before using the unit.
WARNING: Do not use the unit
without the tubes or collection bag proper-
ly attached to avoid flying debris and/or
impeller contact which can cause serious
injury. Always wear eye protection to pre-
vent rocks or debris from being blown or
ricocheting into the eyes and face which
can result in blindness or serious injury.
OFF
VARIABLE
SPEED
HIGH
SPEED
STARTING YOUR UNIT
Your unit has two run positions, HIGH
(high speed) and VAR (variable speed).
Slide the switch to one of these
positions to turn on the unit.
STOPPING YOUR UNIT
To stop your unit, slide the ON/OFF switch
to the OFF position.
8
NOTE: The variable speed control
will not function with the switch in the
HIGH (high speed) position.
With the switch in the VAR (variable
speed) position, the motor speed can be
increased by moving the control toward
the + position or decreased by moving
the control toward the -- position.
D Blowing grass clippings, straw, or
leaves into piles, or removing debris
from corners, around joints, or between
bricks.
Direct air flow by directing the blower
tube down or to one side. Always work
away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and
moving outward. This will help prevent
an accumulation of debris which could
fly into your face.
Be careful when working near plants.
The force of the air could damage
tender plants.
Variable
ON/OFF
Switch
Speed
USING YOUR UNIT AS A VACUUM
Control
WARNING:
Do not vacuum
CAUTION: To avoid causing damage to
the unit, DO NOT attempt to use the
variable speed control during vacuum
use.
OPERATING POSITION
Eye Protection
stones, gravel, metal, broken glass,
etc., to avoid severe damage to the im-
peller. To avoid the possibility of electri-
cal shock, do not attempt to vacuum wa-
ter or other liquids.
Use your unit as a vacuum to pick up
dry material such as leaves, grass,
small twigs, and bits of paper.
Eye Protection
D
For best results during vacuum use,
operate your unit at high speed.
CAUTION: To avoid causing damage to
the unit, DO NOT attempt to use the vari-
able speed control during vacuum use.
D
Move slowly back and forth over the
material as you vacuum. Avoid forc-
ing the unit into a pile of debris as
this can clog the unit.
Keep the vacuum tube about an inch
above the ground for best results.
Blower
Vacuum
USING YOUR UNIT AS A BLOWER
D
WARNING: Inspect the area be-
fore using the unit. Remove all debris
and hard objects such as rocks, glass,
wire, etc., that can ricochet, be thrown,
or otherwise cause injury or damage
during operation.
WARNING: If the unit becomes
clogged, stop the unit andunplug theex-
tension cord. Wait until the impeller has
completely stopped turning, then re-
move the vacuum tubes. Carefully
reach into the vacuum opening and
clear out the clogged debris.
Use your unit as a blower for:
D Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
MAINTENANCE
BEFORE EACH USE
CHECK FOR LOOSE
FASTENERS AND PARTS
S Inlet Cover
WARNING: Disconnect power
source before performing maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to opera-
tor abuse or negligence. To receive full
value from the warranty, the operator must
maintain unit as instructed in this manual.
Various adjustments will need to be made
periodically to properly maintain your unit.
S Blower Tube
S Vacuum Tubes
S Collection Bag
CHECK FOR DAMAGED OR
WORN PARTS
Contact your authorized service dealer
for replacement of damaged or worn
parts.
9
S ON/OFF Switch -- Ensure switch func-
tions properly by moving the switch to
the OFF position. Make sure motor
stops; then restart motor and continue.
S Inlet Cover -- Discontinue use of unit if
inlet cover fails to latch properly or if it is
damaged in any way.
CLEAN COLLECTION BAG
IMPORTANT: THE COLLECTION BAG
MUST BE PROPERLY EMPTIED.
D You must properly empty and maintain
the collection bag to avoid deterioration
and obstruction of air flow.
D Remove the collection bag from the unit
and empty after each use. Do not store
bag without emptying the bag of all con-
tents (grass, leaves, etc.).
D Wash the bag once a year. Remove the
bag from the blower and turn the bag in-
side out. Wash the bag with a water
hose. Allow the bag to hang and dry
completely before you reuse the bag.
AFTER EACH USE
INSPECT AND CLEAN UNIT & LABELS
Stop unit and unplug extension cord.
S After each use, inspect complete unit
for loose or damaged parts. Clean the
unit using a damp cloth.
S Wipe off unit with a clean dry cloth.
SERVICE
HOW TO REMOVE AN OBJECT
FROM THE AIR INTAKE
1. While holding the inlet cover open,
remove the vacuum tubes. The inlet
cover must be held open through all
remaining steps.
2. Carefully reach into the vacuum
opening and clear out the air intake
area. Clear all debris from impeller.
3. Inspect the impeller for cracks. If
cracked or damaged, do not use the
unit. Have parts replaced by your au-
thorized service dealer. Do not at-
tempt to replace them yourself.
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover. The motor must
be stopped and the impeller blades no
longer turning to avoid serious injury
from the rotating blades.
STORAGE
If your blower is to be stored for a period
of time:
WARNING: Perform the following
steps after each use:
S Stop unit and disconnect from the pow-
er source.
S Stop unit and disconnect from the pow-
er source.
S Clean the entire unit before lengthy stor-
age.
S Allow motor to cool before storing or
transporting.
S Open inlet cover and clean any dirt,
grass, or debris that has collected. In-
spect the blower and all tubes. Close
and make sure the cover is latched.
S Clean air vents and air inlet of debris.
S Store your unit and extension cord in a
well ventilated area and covered, if pos-
sible, to prevent dust and dirt accumula-
tion. Do not cover with plastic. Plastic
cannot breathe and may cause con-
densation and eventual rust or corro-
sion.
S Store unit with all guards in place. Posi-
tion unit so that any sharp object cannot
accidentally cause injury.
S Store unit unplugged, well out of the
reach of children.
SEASONAL STORAGE
Prepare unit for storage at the end of
the season or if it will not be used for
30 days or more.
S Check entire unit for loose screws. Re-
place any damaged, worn, or broken
parts.
10
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power sourcebefore
performing all of the recommended remedies below except remedies that re-
quire unit to be operating.
REMEDY
SYMPTOM CAUSE
Unit fails to
operate.
1. Switch in the OFF position.
1. Slide switch to HIGH or VAR
position.
2. Extension cord discon--
nected.
3. Circuit breaker tripped, or
fuse blown.
2. Reconnect extension cord.
3. Reset circuit breaker or
fuse.
4. Contact your authorized
service dealer.
4. Mechanical failure
Unit
vibrates
abnormally.
1. Mechanical failure
1. Contact your authorized
service dealer.
Impeller will
not turn
freely.
1. Debris in air intake area.
2. Mechanical failure.
1. Clean unit. Remove any
debris.
2. Contact your authorized
service dealer.
LIMITED WARRANTY
WEED EATER warrants to the original
purchaser that each new WEEDEATER
brand electric or cordless product is free
from defects in material and workman-
ship and agrees to repair or replace un-
der this warranty any defective WEED
EATER brand electric or cordless prod-
uct within two (2) years from the original
date of purchase.
If your WEED EATER brand electric or
cordless product should fail within the
limited warranty period, return it, com-
plete, prepaid, with proof of purchase, to
the dealer from whom it was purchased
for repair or replacement at the option of
WEED EATER.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically rec-
ommended by WEED EATER for this
tool. Additionally, this warranty does not
cover parts that will wear and require re-
placement with reasonable use during
the warranty period. This warranty does
not cover predelivery setup or normal
adjustments explained in the instruction
manual.
The policy of WEED EATER is to con-
tinuously improve its products. There-
fore, WEED EATER reserves the right to
change, modify, or discontinue models,
designs, specifications, and accesso-
ries of all products at any time without
notice or obligation to any purchaser.
11
|