Viking Ventilation Hood DIL1200 User Manual

VIKING MODEL DIL1200  
INLINE FAN  
ONLY FOR USE WITH: VCWH, VCIH, DBCV, DICV, DCWH, DCIH, DCWL,  
DCWN, DTWS, DSWB 30"W to 66"W WALL AND ISLAND HOODS  
CAUTION  
WARNING  
1. For general ventilating use only. Do not use to exhaust  
hazardous or explosive material and vapors.  
2. To avoid motor bearing damage and noisy and/or  
unbalanced impellers, keep drywall spray, construction  
dust, etc. off power unit.  
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-  
JURY TO PERSONS, OBSERVE THE FOLLOWING:  
1. Use this unit only in the manner intended by the manufac-  
turer. If you have questions, contact the manufacturer or  
your distributor.  
3. Please read specification label on product for additional  
information and requirements.  
4. Unit has an unguarded impeller. Do not use in locations  
where the impeller is readily accessible to people or ani-  
mals.  
5. Screen guards must be installed if impeller is within reach  
of personnel, and less than 7 feet above the floor.  
6. When handling fan wear hand protection and stay  
clear of sharp edges.  
7. Because this unit has rotating parts, safety should be  
exercised during all phases of installation, operation and  
maintenance.  
2. Before servicing or cleaning unit, switch power off at ser-  
vice panel and lock the service disconnecting means to pre-  
vent power from being switched on accidentally. When the  
service disconnecting means cannot be locked, securely  
fasten a prominent warning device, such as a tag, to the  
service panel.  
3. Installation work and electrical wiring must be done by  
a qualified person(s) in accordance with all applicable  
codes and standards, including fire rated construction  
codes and standards.  
4. Sufficient air is needed for proper combustion and ex-  
hausting of gases through the flue (chimney) of fuel  
burning equipment to prevent backdrafting. Follow the  
heating equipment manufacturer’s guidelines and safety  
standards such as those published by the National Fire  
Protection Association (NFPA), and the American Society  
for Heating, Refrigeration and Air Conditioning Engineers  
(ASHRAE), and the local code authorities.  
8. The motor is permanently lubricated. Do not oil or disas-  
semble motor.  
9. Electrical circuit, including speed control, (if used), must  
be rated 5.0 AMPS minimum.  
SPECIFICATIONS  
5
When cutting or drilling into wall, or ceiling, do not  
damage electrical wiring or other hidden utilities.  
MODEL  
VOLTS  
115  
AMPS  
4.84  
CFM  
DUCT SIZE  
10” DIA.  
6. Ducted fans must always be vented to the outdoors.  
7. To reduce risk of fire, use only metal ductwork.  
8. This unit must be grounded.  
DIL1200  
1200  
INSTALLER: Leave this Manual With The Homeowner  
HOMEOWNER: Use And Care Information On Page 4  
1
 
CONNECT WIRING TO DIL1200 INLINE FAN  
CONNEC
T
W
IRIN
G
T
O
T
H
E
R
ANG
E
H
OO
D
R
OUG
H
I
N
B
OX  
1. The opposite end of this wiring will be connected to the 1. Run 115VAC electrical power cable from the service panel  
range hood rough in box in the next step.  
2. Remove wiring box cover from the inline fan.  
3. Attach an appropriate UL approved cable connector to  
the wiring hole in the wiring box.  
4. Bring electrical wiring through the cable connector in the  
electrical box.  
and from the inline fan to the range hood rough in box.  
2. Remove appropriate knockouts from the range hood rough  
in box.  
3. Attach appropriate UL approved cable connectors to the  
wiring holes in the range hood rough in box.  
4. Feed 6” of power cable through the cable connectors in  
the range hood rough in box.  
5. Make electrical connections per the diagram shown below  
5. Using the diagram below make all electrical connec-  
tions to the range hood rough in box including the  
Cordset Assembly part number PV300207 supplied  
with DIL1200.  
6. Attach wiring box cover to range hood rough in box.  
6. Attach wiring box cover to rough in box.  
7. Connect the plugin power cables of the rough in box to  
the range hood.  
3
 
CONNECTING DUCT WORK TO DIL1200 INLINE FAN  
USE AND CARE  
Two duct clamps part number 001377-000 are included  
with this unit and are intended to simplify fan installation  
and isolate fan vibration from the rigid metal duct.  
Disconnect electrical power supply and lock out service panel  
before cleaning or servicing this unit.  
CLEANING  
Note: The duct clamps are  
convenient in installations  
where regular removal of the  
fan in necessary for inspec-  
tion and cleaning.  
Periodic inspection and cleaning is recommended. The fre-  
quency of inspection and cleaning should be adjusted accord-  
ing to the type and amount of cooking.  
8mm  
neoprene pad  
The interior of the fan can to accessed by removing the duct  
The built in hanger tab of the duct clamps are not intended to clamp and gently moving the duct work away from the inlet  
support the weight of the inline fan. The inline fan should be of the fan.  
supported with the integral brackets of the inline fans.  
If excess build up is present it should be removed from the  
If special supports are required in anticipation of earthquakes interior of the fan and from the impeller of the fan.  
the duct clamps that are supplied with the DIL1200 are not  
intended to meet these requirements.  
MOTOR LUBRICATION  
To minimize vibration, leave a 1/4” gap between the inline fan  
collars and rigid duct.  
semble motor.  
The motor is permanently lubricated. Do not oil or disas-  
Tighten the two screws until the fan and duct are snugly attached.  
The duct work at the inlet of the inline fan is to be connected  
to the range hood.  
The duct work at the out box of the inline fan is to be con-  
nected to a roof or wall cap.  
A inline butterfly damper part number PV300006 is included  
with the DIL1200. The damper can be installed anywhere  
in the duct system. Damper must be installed so that the  
airflow direction will open the butterfly blades. Mounting the  
damper in an inverted position may prevent the blades from  
closing completely. The preferred installation position is ver-  
tical as shown below.  
Damper  
Airflow  
Direction  
RSK  
Damper  
Duct  
Collar  
RANGE  
HOOD  
VIKING RANGE CORPORATION  
GREENWOOD, MISSISSIPPI 38930 USA  
Item #:450353  
Date: 060707  
4
 

Taylor Computer Hardware CONROE1333 DVI H User Manual
Teac Computer Drive CD W28PU User Manual
Toshiba Cash Register MA 227 User Manual
Tripp Lite Surge Protector MT 6PLUS User Manual
Tripp Lite TV Cables B118 002 User Manual
Victory Refrigeration Refrigerator RSA 1D S7 EW User Manual
Vienna Acoustics Speaker Schonberg Series User Manual
ViewSonic Flat Panel Television VS11857 User Manual
ViewSonic Projector VS12617 User Manual
Wachsmuth Krogmann Hot Beverage Maker XB6168 User Manual