®
ViewSonic
- Quick Start Guide
Digital Photo Frame
- Guide de démarrage rapide
- Guía de Inicio Rápido
DPX802
Model No. : VS12075
Important Safety Instructions
1.
2.
3.
4.
5.
6.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this unit near water.
Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in
this guide for further instructions.
7.
8.
9.
Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade and
the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs. Convenience receptacles and the point where they exit from the
unit. Be sure that the power outlet is located near the unit so that it is easily
accessible.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the unit. When a cart is used,
use caution when moving the cart/unit combination to avoid
injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the unit has been damaged in any way, such as: if the power-supply cord or
plug is damaged, if liquid is spilled onto or objects fall into the unit, if the
unit is exposed to rain or moisture, or if the unit does not operate normally
or has been dropped.
Quick start guide
ꢁ
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive
2002/95/EC of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS
Directive) and is deemed to comply with the maximum concentration values
issued by the European Technical Adaptation Committee (TAC) as shown below:
Proposed Maximum
Concentration
Actual
Concentration
Substance
Lead (Pb)
0.1%
0.1%
0.01%
0.1%
0.1%
< 0.1%
< 0.1%
< 0.01%
< 0.1%
< 0.1%
Mercury (Hg)
Cadmium (Cd)
6+
Hexavalent Chromium (Cr
)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers
(PBDE)
0.1%
< 0.1%
Certain components of products as stated above are exempted under the Annex of
the RoHS Directives as noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in
other lamps not specifically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes,
and electronic ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight,
aluminium containing up to 0.4% lead by weight and as a cooper alloy
containing up to 4% lead by weight.
ꢂ
Quick start guide
Package contents
Check your Digital Photo Frame package for the following items.
•
•
•
•
•
•
Digital Photo Frame
Power adapter
Stand
Quick Start Guide
USB cable
Replacement front panel*
* The bundled front panel varies depending on the model you purchase.
Replacing front panel
If your Digital Photo Frame package contains a spare front panel, follow these
instructions to replace the front panel for personal preference.
1. Locate the indent on the edge
near the memory card socket.
2. Follow the direction of the figure
and gently lift the front panel.
2
1
3. To install a new front panel, align
the panel edge to the Digital
Photo Frame and gently place the
panel on the device.
3
Quick start guide
ꢃ
Connect
1. Align the head of the stand with the
socket, then rotate clockwise until the
stand locks into place.
2. Plug the power adapter from the device to a power outlet.
Locate control keys (in the back panel)
Locate the control buttons in the back panel according to the following
table.
Button
OK
Function
Enter or confirm the selection
Move to the previous or left selection
Left
Right
Up
Move to the next or right selection
Move upward
Down
Move downward
Power On/Off
Turn ON/OFF the device
Turn on the device
Press
turn on the device, then the main
screen appear. The LED will light up in blue
color.
Turn off the device
Hold
for 2 seconds then release to turn off
the device.
Tips: If you can’t turn on the device normally, please try to turn off the device
then turn it on again.
ꢄ
Quick start guide
Remote Control
Refer to the following image and table for details of the remote control.
1
2
3
4
5
6
7
8
26
25
24
23
22
21
20
19
9
10
11
12
View
18
13
Setting
14
15
17
16
No.
1
2
Item
POWER
MUSIC
VIDEO
MUTE
Description
Disabled on this model
Shortcut to the Audio menu 15 ROTATE
No.
14 EXIT
Item
Description
Go back one menu level
Rotate photo 90° clockwise
Navigate down in menus/
skip to next available media
3
Shortcut to the Video menu 16 DOWN/NEXT
4
5
6
7
Mute audio output
17 FULL SCREEN Enlarge image to full screen
LEFT/
REWIND
Navigate left in menus/
rewind audio playback
VOLUME UP Increase audio volume
18
SOURCE
VOLUME
DOWN
Shortcut to Source menu
Decrease audio volume
19 OK
Select/accept selected item
Display advanced media
options in media menus
Navigate up in menus/skip
to previous available media
20 View
Stop Video or Audio
playback
8
9
STOP
21 UP/PREV.
22 PLAY
Start slide show of available
photos
SLIDE SHOW
Play selected media
10 CALENDAR Disabled on this model
11 MAIN MENU Display Main Menu
23 PAUSE
24 ZOOM IN
Pause current media
Enlarge photo image size
RIGHT/
FORWARD
Navigate right in menus/fast
forward audio playback
12
25 ZOOM OUT Reduce photo image size
26 PHOTO Shortcut to Photo menu
13 Setting
Shortcut to Settings menu
• POWER and CALENDAR functions are disabled on this model.
• ZOOM IN/OUT are only available using the remote control.
Quick start guide
ꢅ
Settings
Brightness
Allows you to adjust the screen brightness.
Language
Allows you to select the language you need.
Default
Go to SETTINGS > Default, then select Yes to retore to the factory default
setting or No to discard the selection.
Set Beep
Allows you to turn on/off the key control sound.
Status
Displays the software version and the current memory size.
Auto Tilt
Automatically adjusts the orientation of the screen when you rotate the frame.
The default value is On.
Auto Tilt does not compensate if the frame is placed upside
down—only 90° rotation clockwise or counter clockwise is
supported.
Volume
Allows you to adjust the volume between 0 and 16. The default value is 8.
You will see Low battery please plug-in the power adapter
on the screen when the batterty is low. Plug the power adapter
immediately, or the device will be turned off soon.
ꢆ
Quick start guide
View Photos
From the main screen, press the Up and Down navigation keys to select
PHOTO, then select the photo source you want to display.
Photos pre-stored in the device will appear when no memory card or USB
flash disk is connected.
When photo source is selected, press OK to switch between 3 view modes:
•
•
Browse mode: manual viewing of photos one-by-one
Thumbnail mode: list of all photos
When viewing photos in Thumbnail mode, hold the Down navigation
key
for 2 seconds then release to quickly enter the setting menu for
photo-related settings, or press View on the remote control.
•
Slideshow mode: automatically shifting display of photos
To exit the PHOTO function, switch to Thumbnail mode, then press the Up
navigation key.
View photos from your memory card or USB flash
disk
1. Insert your memory card
with photos into the
Compact Flash card
(Right side)
corresponding slot,
OR: insert your USB
flash disk into the USB
port.
Memory Stick/ XD/
Secure Digital/ MMC card
USB flash disk
2. Photos on your memory
card will appear after a
few seconds.
Copy photos from your photo source
1. In Thumnail mode, press the navigation keys to select one photo.
2. Hold the Down navigation key
for 2 seconds then release to quickly
enter the setting menu, or press View on the remote control.
3. Select Copy to or Copy all to, then press OK.
4. Select the source where you want to store the selected photos.
5. Press OK to copy.
Quick start guide
ꢇ
Copy multi-photos
1. In Thumnail mode, select one photo, then press the Down navigation
key
. The selected photo is labeled with a "+" mark.
2. Repeat step 1 to other photos you want to copy to a source.
3. Finishing selection, repeat step 2–5 in section Copy photos from your
photo source.
Delete photos from your photo source
1. In Thumnail mode, press the navigation keys to select one photo.
2. Hold the Down navigation key
for 2 seconds then release to quickly
enter the setting menu, or press View on the remote control.
3. Select Delete or Delete all, then press OK.
Delete multi-photos
1. In Thumnail mode, select one photo, then press the Down navigation
key
. The selected photo is labeled with a "+" mark.
2. Repeat step 1 to other photos you want to delete.
3. Finishing selection, repeat step 2–3 in section Delete photos from your
photo source.
Photo Setting menu
While in Thumnail mode, hold the Down navigation key
for 2 seconds
then release to enter the photo setting menu You can adjust the screen view,
slideshow sequence/effect/speed, copy or delete photos, effect, rotate photos,
and set background music from the photo setting menu.
•
Full Screen: sets the displayed photo to full screen.
When set to Full Screen, the displayed photo is automatically cropped to
fit the screen.
•
•
•
•
•
•
•
•
Slideshow Sequence: sets the photo transition sequence.
Slideshow Effect: sets the photo transition effect.
Slideshow Speed: sets the photo transition frequency.
Copy/Copy all to: copy one or all photos to a selected source.
Delete/Delete all: delete one or all photos.
Effect: displays photos in black and white.
Rotate: rotate the displayed photo 0/90/180/270 degrees
Background Music: display photos with background audio. Default value
is Off.
Photo and Audio files must be from the same Source, for example,
USB flash disk.
10
Quick start guide
Supported format
JPEG: JPEG Baseline (4:4:4/4:2:2/4:2:0, support up to 8000x8000 pixels),
Progressive JPEG (Support up to 1024x1024 pixels)
BMP: MS Windows V3.1/4/8/16/24 uncompressed Bitmap. (Support up to
1024x1024 pixels)
The system allows you to display 4000 photos at most from your own memory
card or USB flash disk.
Quick start guide
11
View Video
From the main screen, press the navigation keys to select VIDEO, then select
the video source you want to play.
Videos pre-stored in the device will appear when no memory card or USB
flash disk is connected.
1. Insert your memory card containing video into the corresponding slot, or
insert your USB flash disk into the USB port. Videos on your memory
card will appear after a few seconds. See page 9 for memory card and
USB port locations.
2. Press the navigation keys to select the desired video, then press OK to
view.
3. The selected video begins to play.
To exit the VIDEO functions, press Main Menu on the remote control.
Advanced video functions
Press View on the remote control or hold the Right navigation key
for two seconds to enter the video settings menu.
Repeat video
1. Press the navigation keys to select one video.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the video settings menu.
3. Select Video Repeat, then press OK.
4. Select All to repeat all videos, or One to repeat only the selected video.
5. Press OK to play.
Copy video from your video source
1. Press the navigation keys to select one video.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the video settings menu.
3. Select Copy to or Copy all to, then press OK.
4. Select the source where you want to store the selected video.
5. Press OK to copy.
1ꢀ
Quick start guide
Copy multi-video
1. Select one video, then press the Right navigation key. The selected video
is labeled with a "+" mark.
2. Repeat step 1 for the other videos you want to copy to a source.
3. Finishing selection, repeat step 2–5 in section Copy videos from your
video source.
Delete video from your video source
1. Press the navigation keys to select one video.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the video settings menu.
3. Select Delete or Delete all, then press OK.
Delete multi-video
1. Select one video, then press the Right navigation key. The selected video
is labeled with a "+" mark.
2. Repeat step 1 for any other videos you want to delete.
3. Finishing selection, repeat step 2–3 in section Delete videos from your
video source.
Volume adjustment
1. Press the navigation keys to select one video.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the video settings menu.
3. Select Volume, then press OK.
4. Select the desired volume from 0 to 16.
5. Press OK to set the volume.
The volume can also be set through the Setting and Audio menus.
Supported format
The following video formats are supported:
•
•
•
M-JPEG
MPEG1
MPEG4 (SP)
Quick start guide
1ꢁ
Play Audio
From the main screen, press the navigation keys to select AUDIO, then select
the audio source you want to play.
Audio pre-stored in the device will appear when no memory card or USB flash
disk is connected.
1. Insert your memory card containing audio into the corresponding slot,
or insert your USB flash disk into the USB port. Audio on your memory
card will appear after a few seconds. See page 9 for memory card and
USB port locations.
2. Press the navigation keys to select the desired audio, then press OK to
view.
3. The selected audio begins to play.
To exit the AUDIO functions, press Main Menu on the remote control.
Advanced audio functions
Press View on the remote control or hold the Right navigation key
for two seconds to enter the audio settings menu.
Repeat audio
1. Press the navigation keys to select one audio.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the audio settings menu.
3. Select Music Repeat, then press OK.
4. Select All to repeat all audio, or One to repeat only the selected audio.
5. Press OK to play.
Copy audio from your audio source
1. Press the navigation keys to select one audio.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the audio settings menu.
3. Select Copy to or Copy all to, then press OK.
4. Select the source where you want to store the selected audio.
5. Press OK to copy.
1ꢂ
Quick start guide
Copy multi-audio
1. Select one audio, then press the Right navigation key. The selected audio
is labeled with a "+" mark.
2. Repeat step 1 for the other audio you want to copy to a source.
3. Finishing selection, repeat step 2–5 in section Copy audio from your
audio source.
Delete audio from your audio source
1. Press the navigation keys to select one audio.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the audio settings menu.
3. Select Delete or Delete all, then press OK.
Delete multi-audio
1. Select one audio, then press the Right navigation key. The selected audio
is labeled with a "+" mark.
2. Repeat step 1 for any other audio you want to delete.
3. Finishing selection, repeat step 2–3 in section Delete audio from your
audio source.
Volume adjustment
1. Press the navigation keys to select one audio.
2. Press View on the remote control or hold the Right navigation key
for two seconds to enter the audio settings menu.
3. Select Volume, then press OK.
4. Select the desired volume from 0 to 16.
5. Press OK to set the volume.
The volume can also be set through the Setting and Video menus.
Supported format
The following audio formats are supported:
•
•
MP3 layer 1
MP3 layer 2
Quick start guide
1ꢃ
Customer Support
For technical support or product service, see the table below or contact your
reseller.
Note : You will need the product serial number.
T=Telephone
F=Fax
Country/Region Web Site
E-mail
AUS=1800 880 818
NZ=0800 008 822
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-1202
Canada
Europe/Middle East/
Baltic countries/North
Africa
Contact your reseller
Hong Kong
India
T= 852 3102 2900
T= 1800 11 9999
T= 080 265 9080
Korea
Latin America
(Argentina)
T= 0800 666 0194
T= 0800 891 6984
T= 800 440 303
Latin America
(Brazil)
Latin America
(Chile)
Latin America
(Columbia)
T= 01 800 915 6588
T= 001 800 514 6518
Latin America
(Mexico)
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Latin America
(Peru)
T= 0800 53458
T= 853 700 303
Macau
T= 1-800-688-6688 (English)
T= 1-866-379-1304 (Spanish)
F= 1-909-468-1202
Puerto Rico &
Virgin Islands
Singapore/Malaysia/
Thailand
T= 65 6461 6044
South Africa
United Kingdom
T (Toll-Free)= 1-800-688-6688
United States
T (Toll)= 1-424-233-2530
F= 1-909-468-1202
1ꢄ
Quick start guide
|