ViewEra Flat Panel Television V202 User Manual

20.1" WIDE SCREEN  
TFT-LCD MONITOR  
V202 Series  
USER MANUAL  
Rev. 1.0  
 
EMC COMPLIANCE  
This device has been tested and found to comply with the standards for a class B digital device,  
pursuant to Part 15 of FCC Rules. Those standards are designed to provide reasonable protection  
against harmful interference in a residential installation. This device generates and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications.  
If this device does cause harmful interference to radio or television reception, which can be determined  
by turning the device off and on, user is encouraged to try to correct the interference by one or more of  
the following measures:  
> Reorient or relocate the receiving antenna  
> Increase the separation between the device and receiver  
> Plug the device into a wall outlet different from that connected to the receiver.  
> Consult the dealer or an experienced technician for help.  
CAUTION: any change or modification not expressly illustrated in this manual may void the warranty.  
NOTE: any unshielded cable is not allowed to be used in the device.  
1
 
IMPORTANT PRECAUTIONS  
1. Before using this device, please read all the instructions in this manual carefully.  
2. Please keep the manual carefully for future reference.  
3. Unplug this device from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.  
Use a damp or wet cloth to clean. Please use LCD screen detergent for cleaning if it is still dirty.  
4. Do not use the parts not recommended by the manufacturer, otherwise it may cause a hazard.  
5. When unplugging the power cord of the display, please hold the plug with your hands. Do not pull the  
cord directly.  
6. Do not place any object on the power cord. Do not trample it either.  
7. Do not use the device near water sources, e.g. bathtub, basin, kitchen sink, or washing machine. Do  
not place the device on a wet floor, or near a swimming pool etc. Do not touch the screen with your  
fingers or other hard objects.  
8. Slots and openings on the housing and its back or bottom are provided for ventilation. To ensure  
reliable operation of the components and to protect them from overheating, these openings must not  
be blocked or covered placing the device on a bed, sofa, rug, or other similar surface. The device  
should never be placed near or over a radiator or heater and should not be placed in a built-in  
installation unless proper ventilation is provided.  
9. Make sure that the device is at least 5 cm distance from the wall or other objects around when it is in  
use.  
10. As a safeguard measure, the display is equipped with a power cord with three-terminal  
plug, the third terminal is grounded. If the plug can not be inserted into the outlet, please contact an  
electrical technician for replacing the original outlet while keeping the safeguard measure in effect.  
11. Ensure that the power socket and cord in use are able to take the sum of the rated currency of all the  
products.  
12. Do not put the device at the place where user is subject to mal-operation.  
13. Observe all the warnings and instructions described in the manual.  
14. Do not overload the power outlet or use any extension cord, otherwise it may cause fire or electric  
shock.  
15. Do not attempt to repair this device yourself since opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer servicing to qualified service personnel.  
16. Unplug this display from the wall outlet and refer servicing to qualified service personnel under the  
following conditions:  
a. When the power cord or plug is damaged or worn.  
b. If the device has been dropped or its housing has been damaged.  
c. When the performance of the device deteriorates distinctly.  
17. The power cord is the main facility to turn on/off the device; unplug it if the device is not used for a  
long period of time.  
18. Store the device at a place of good ventilation; avoid strong sunlight, high temperature or humidity.  
19. Store the device at a place at -20~55 Celsius degree room temperature.  
2
 
1. Package Contents  
Unpack the package and check you have the following items.  
20.1"TFT-LCD monitor  
VGA signal cable  
Power cord  
User manual  
DVI signal cable  
Audio cable  
If any of the items is missing, please contact with your dealer at which you  
purchased the monitor.  
2. Installation  
2.1 Rear Panel  
1. Power supply: AC 100-240 V, 60/50 Hz.  
2. Audio: Connecting one end of the PC audio cable to AUDIO on the monitor and the other end to  
the sound card audio in on a computer.  
3. DVI: Connecting one end of DVI cable to DVI connector on the monitor and the other end to a  
video/ graphic card on a computer, if your video/ graphic card supports DVI.  
4. VGA: Connecting one end of VGA cable to VGA connector on the monitor and the other end to a  
video/ graphic card on a computer.  
3
 
2.2 Installation  
The monitor is equipped with an automatic sensing AC power adapter for a voltage range from 100 to  
240 VAC at a frequency of 50 to 60 Hz. Before connecting the cables, please make sure that the  
monitor and the computer power are both turned off. Please follow the steps to install your monitor.  
2.2.1 Connecting the signal cable  
Plug one end of the VGA cable or DVI cable to the computer and the other end to the video signal  
connector on the monitor, and then tighten the two screws on the cable connector.  
2.2.2 Connecting power cord  
Plug one end of the power cord into the input port of the monitor power supply and then insert the  
other end into the socket of the electrical source.  
2.2.3 Connecting the audio cable  
Plug one end of the audio cable to audio jack on either computer or video device and the other end  
to audio jack on the monitor.  
2.2.4 Installing the monitor base  
1. Take the monitor and the base out of the box and place its side on the table.  
2. Align the monitor base with the monitor arm and then push the base into the knighthead on the  
monitor arm until the monitor base is securely connected to the monitor arm.  
2.2.5 Power on  
Turn on your monitor and computer. The LED indicator will light green (or blue) when the screen is  
under normal condition. If the LED indicator lights red, please check if the signal cable is securely  
connected between the computer and the monitor.  
4
 
2.3 Resolution setup  
For the best display quality, please set the monitor type in Windows.  
Control Panel > Display > Settings > Advanced > List All Modes  
For V202 series, please set to 1680 × 1050 @ 60Hz.  
Note: If your video/ graphic card does not support the resolution of 1680 x 1050, then you can try to  
set the resolution to 1280 x 960 or 1280 x 768 to avoid picture stretching.  
5
 
3. Control Functions  
3.1 User Controls  
The monitor digital control functions are located on the front panel. They are shown in the figure  
below and described in the following paragraphs.  
1. Power switch with LED indicator key: It is used to turn on or off the monitor. When the monitor is  
turned on, the LED is lit up in green (or blue). When the monitor is in power saving mode, the LED  
will turn red and flashing.  
2. OSD Menu key: When it is pressed, the OSD menu appears on the screen. It is also used to  
confirm the function selection.  
3. +key: It is used to move the cursor clockwise or increase the value of the control function. It is  
also a shortcut key to enter Brightness adjustment.  
4. - key: It is used to move the cursor counterclockwise or decrease the value of the control  
function. It is also a shortcut key to enter Contrast adjustment.  
5. AUTOkey: It is used to adjust the picture to the best display quality in VGA mode. If the picture is  
shifted to one side, especially at the first time the monitor is connected to a new system, you can  
correct the display position by pressing this key.  
3.2 OSD menu  
a. OSD menu with VGA connection  
b. OSD menu with DVI connection  
1. Auto Adjustment: Adjust geometry of the picture automatically. (for VGA mode only)  
2. Brightness: Adjust the brightness level of the picture.  
3. Contrast: Adjust the difference in luminance between light and dark areas of the picture.  
4. H. Position: Adjust the horizontal position of the picture.  
5. V. Position: Adjust the vertical position of the picture.  
6. Clock: Adjust the frequency of the signal.  
7. Phase: Adjust the phase of the signal.  
6
 
8. Signal Source: Change the signal mode between VGA and DVI on OSD.  
9. Color: Adjust the color temperature of the picture.  
9300K - Select the color temperature of 9300K.  
7800K - Select the color temperature of 7800K.  
6500K - Select the color temperature of 6500K.  
User mode: Adjust R. G. B. gain levels.  
W-B: Auto color balance.  
10. Volume: Adjust the speaker volume.  
11. Sharpness: Adjust the picture to be in focus.  
12. OSD Position/ Transparency: Adjust the OSD display position and transparency.  
13. Recall: Reset the factory default settings.  
14. Language: Set the language of the OSD windows.  
15. Exit: Close the OSD menu.  
16. Resolution in use  
17. Horizontal frequency in use  
18. Vertical frequency in use  
19. OSD Timer: Set the OSD menu display time. (It appears when Signal Sourceis selected.)  
7
 
4. Specifications  
Model  
V202 Series  
Active TFT-LCD  
Features  
Panel Type:  
Size:  
20.1"diagonal  
Pixel Pitch:  
Brightness:  
Contrast Ratio:  
0.258 (W) × 0.258 (H) mm  
270 cd/m2 (min), 300 cd/ m2 (typical)  
500:1 (min,),800:1 (typical)  
5 ms (typical)  
Response Time:  
Viewing Angle(H / V)  
Max. Resolution:  
Display Color  
160°/160° (typical)  
1680 (W) x 1050 (H)  
16.7M  
Supported resolution  
640 x 480 @ 60/ 72/ 75 Hz  
800 x 600 @ 60/ 72/ 75 Hz  
1024 x 768 @ 60/ 70/ 75 Hz  
1280 x 768 @ 60 Hz  
1280 x 960 @ 60 Hz  
1280 x 1024 @ 60/ 75 Hz  
1600 x 1200 @ 60 Hz  
1680 x 1050 @ 60 Hz  
Video Input  
Analog:15-pin, D-sub connector  
Digital: DVI connector  
Display Area  
17.06 (W) x 10.67 (H) inches  
[433.44 (W) x 270.90 (H) mm]  
100-240V /60-50Hz  
Power Supply Input voltage:  
Power Consumption  
Audio  
50 watts (maximum), 5 watts (standby)  
Built-in speakers, 2W x 2  
Horizontal:30-80KHz; Vertical: 55-75Hz  
21.85 (W) x 16.54 (H) x 6.50 (D) inches  
[555 (W) x 420 (H) x 165 (D) mm]  
FCC, CE, CB  
Frequency  
Dimensions (pack size)  
Safety & EMI  
Weight  
N.W.: 14.3 lbs (6.5 Kg)  
G.W.: 17.6 lbs (8.0 Kg)  
5°C ~ 40°C; 10%-85% RH  
-20°C ~ 55°C; 5%-95% RH  
VESA 100 bracket  
Operating Conditions  
Storage Conditions:  
Wall mount  
8
 
5. Dead Pixel Policy  
Dead pixels on the TFT LCD panel are sometimes inevitable. The replacement policy varies with  
different models. Please refer to the product specification on ViewEras website.  
6. Warranty & Customer Service  
a. Warranty  
ViewEra warrants the V202 series TFT-LCD monitors for 1 year on LCD panel, parts and labor. For  
detailed information, please refer to our website.  
(http:// www.viewera.com/warranty.htm)  
b. Customer Service  
Contact your ViewEra retailer or ViewEra for after sale service.  
You may contact ViewEra Customer Service for technical support or RMA:  
By Mail: 328 Paseo Tesoro, Walnut, CA 91789  
2. By Telephone: (800)900-6098  
3. By Fax: (909)595-3526  
4. By E-mail: Tech. Support-- [email protected]  
The business hours are 9:00 am 6:00 pm PST, Mon Fri.  
7. Registration  
To receive the full warranty applicable to your purchase, you need to get on our website to fill out the  
online registration form in Support - http://www.viewera.com/registration.htm , and then email or fax us  
your purchase invoice. (Email: [email protected] ; Fax: (909)595-3526 )  
9
 
8. Troubleshooting  
1) No image  
Check if the power cordthe monitor and the power plug are well connected.  
Check if the monitor is off, please contact [email protected] for assistance.  
2) No Input Signalappears.  
Check if the VGA cable is tightly connected between the video output connector on the video  
card and the video input connector on the monitor.  
Check if your video card driver is correctly installed. If possible, please re-install or update your  
video card driver.  
3) The image is blurry or not positioned correctly.  
Enter the Image menu in the OSD and then select Auto Adjustto adjust the display to optimum.  
Refer to Chapter 2.6, set your monitor to its native resolution of 1680 by 1050.  
4) The color is abnormal  
Check the connection of signal cable and make sure the two screws on the connector are  
securely tightened.  
Chick if there is any pin on the signal cable bent or broken off. If there is, it is required to replace  
the signal cable.  
Enter the Color Temperature menu and select AUTO Color to recall the factory settings for color  
hue.  
10  
 

Tripp Lite Network Cables P580 010 User Manual
Tripp Lite Switch B022 002 KT R User Manual
Troy Bilt Blower TBTB User Manual
VBrick Systems Satellite TV System MPEG 1 User Manual
Victory Refrigeration Refrigerator VM 1 User Manual
ViewSonic Personal Computer SCZ55BKUS0 User Manual
ViewSonic Projector PRO8400 User Manual
Vizio Car Satellite TV System E320i BO User Manual
Waves Network Card Trans X User Manual
Weber Charcoal Grill 3994601 User Manual