Venturer Digital Photo Frame VPF1010DL BLK User Manual

Dig ita l Pic ture Fra m e  
with128MB  
Inte rna l Me m o ry  
O p e ra ting Instruc tio ns  
VPF810DL-C HER  
VPF1010DL-BRW / VPF1010DL-BLK  
Need More Help?  
DO NOT RETURN THIS PRODUCT TO THE STORE  
DPolweansloeadvifsroitmonWliwnew.hSeolmpaantuhatlstp.c:/o/wmw. Awl.l1M8a0n0ucaulsstoSmeaerrcshuApnpdorDt.ocwomnlo/Va7d.  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s  
instructions.  
8. Donotinstallnearanyheatsourcessuchasradiators, heatregisters, stoves, orotherapparatus  
(including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has  
two blades with one wider than the other. A grounding type plug has two blades and a third  
grounding prong. The wide blade or the third prong is provided for your safety. When the  
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete  
outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with a cart, stand, tripod, bracket, or table specified by the  
manufacturer, or sold with the apparatus. When a cart is used, use  
Portable  
Cart Warning  
cautionwhenmovingthecart/apparatuscombinationtoavoidinjury  
from tip-over.  
13. Unplug this apparatus during lightning storms or when unused for long periods.  
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has  
beendamagedinanyway, suchasthepower-supplycordorplugisdamaged, liquidhasspilled  
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,  
does not operate normally, or has been dropped.  
FCC Statements  
This device complies with the Part 15 of the FCC rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference that may cause  
undesirable operation.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates, uses  
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television reception, which can be determined  
by turning the equipment off and on, the user is encouraged to try to correct the interference by one  
or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an AC power outlet on a circuit different from that to  
which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Warning: Changes or modifications to this unit not expressly approved by the party responsible for  
compliance could void the user's authority to operate the equipment.  
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.  
 
- 3 -  
QUICK START GUIDE  
ENTER  
EXIT  
SETUP  
MENU  
MODE  
Press the Slide Show button (  
displayingphotos.  
)to start  
Insert a memory card.  
For easy removal, Memory Devices will  
stick out a bit.  
Switch to ON  
position.  
2
To AC outlet  
1
To DC IN 9V jack  
TABLE OF CONTENTS  
SafetyPrecautions ........................ 2  
ImportantSafetyInstructions ....... 3  
Quick Start Guide .......................... 4  
TableofContents ........................... 4  
Accessories ................................... 5  
RemoteControl .............................. 5  
ControlReferenceGuide .............. 6  
ControlFunction&DisplayIcon... 7  
PhotoViewingSetupMenu ......... 12  
FullScreen................................ 12  
Photo Slide Show Effect .......... 12  
Photo Slide Show Speed .......... 12  
On-screenLanguage ................ 12  
ListeningtoMusic ....................... 13  
Listening to Music .................... 13  
MusicRepeat ............................ 13  
WatchingVideoFiles ................... 14  
Watching Video Files ................ 14  
VideoRepeat ............................ 14  
Installation ..................................... 8  
Using the Stand ......................... 8  
Mounting on the Wall .................. 8  
Copying/DeletingMediaFiles ... 15  
CopyingFiles ............................ 15  
Deleting Files ............................ 15  
PowerSupply ................................. 9  
InsertingMemoryDevices .......... 10  
TroubleshootingGuide ................ 18  
ViewingPhotos ............................ 11  
Viewing Photos Slide Show ...... 11  
Viewing Photos ......................... 11  
Maintenance ................................. 16  
Cleaning the Unit ...................... 16  
Cleaning the LCD Screen ......... 16  
 
- 4 -  
ACCESSORIES  
Please check and identify the supplied accessories.  
To order accessories visit web site (http://www.1800customersupport.com/V7)  
AC Power Adapter .................................................................................... x 1  
RemoteControl ......................................................................................... x 1  
REMOTE CONTROL  
UsingtheRemoteControl  
Point the remote control at the REMOTE SENSOR located on the unit.  
When there is a strong ambient light source, the performance of the infrared  
REMOTE SENSOR may be degraded, causing unreliable operation.  
The recommended effective distance for remote operation is about 16 feet (5  
meters).  
Remove the plastic sheet before using the remote control.  
TO CHANGE REMOTE BATTERY  
1. Open the battery door.  
2. Insert one CR2025 (3V) size battery.  
BATTERY REPLACEMENT  
When the battery becomes weak, the operating distance of the remote control will  
be greatly reduced and you will need to replace the battery.  
NOTE:  
If the remote control is not going to be used for a long time, remove the battery  
to avoid damage caused by battery leakage corrosion.  
PLACEMENT  
rear of the unit  
WARNING:  
Do not dispose of the battery in a  
fire. It may leak and/or explode.  
CAUTION:  
Danger of explosion if battery is  
incorrectly replaced. Replace only  
with the same or equivalent type.  
 
- 5 -  
CONTROL REFERENCE GUIDE  
 
- 6 -  
CONTROL FUNCTION & DISPLAY ICON  
 
- 7 -  
INSTALLATION  
UsingtheStand  
The unit can be placed either horizontally or vertically to fit the photos on display.  
You can rotate the stand as shown below to stand the unit vertically.  
MountingontheWall  
The unit can be mounted either horizontally or vertically on the wall by the  
mounting holes on the back of the unit.  
100mm  
155mm  
Caution:  
Mounting the unit requires special skills that should only be performed by  
qualified personnel. You should not attempt to do the work yourself.  
Make sure that the wall mount is being fixed securely enough so that it meets  
safety standards.  
 
- 8 -  
POWER SUPPLY  
RIGHT SIDE OF UNIT  
AC power adapter  
AC between 100V and 120V  
3
Turn the Power  
switch to ON  
position  
2
To AC outlet  
1
To DC IN 9V jack  
After turning on the unit, if there is no memory card or USB flash drive connected  
to the unit, it will display media files stored on the internal memory (  
unit.  
) of the  
When a memory card or/and USB flash drive is/are inserted, it will display media  
files from the recently connected media or device in a last-in, first-display order.  
You can press the SOURCE (  
) button to switch among different Memory  
Devices.  
Caution:  
The AC power adapter included with this unit is for its use only. Do not use it with  
other equipment.  
Turn off the unit before unplugging the AC power adapter from the unitto avoid  
the unit being damaged.  
When the unit is not going to be used for a long time, disconnect the AC power  
adapter from the AC power outlet.  
Important:  
Be sure to use it near the wall outlet. If a malfunction occurs, disconnect the  
plug from the wall outlet at once.  
When the AC power adapter is plugged in, the apparatus is not completely  
disconnected from the main power source, even when the unit is turned off.  
Warning:  
The AC power adapter is used as the disconnect device. It shall remain readily  
operable and should not be obstructed during intended use. To completely  
disconnect the apparatus from the main power supply, the AC power adapter of  
the apparatus should be disconnected from the AC power outlet completely.  
 
- 9 -  
INSERTING MEMORY DEVICES  
Stop the unit before connecting or disconnecting a memory card or  
USB flash drive. Do NOT connect or disconnect external equipment  
when the unit is playing, coping or deleting files.  
The unit is compatible with the following Memory Devices (sources):  
• USB Flash Drive  
• Compact Flash (CF)  
• Secure Digital Card (SD)  
• Multi Media Card (MMC)  
• Memory Stick Pro (MS Pro)  
• Extreme Digital (xD)  
USBFlashDrive  
CF  
SD/MMC  
MS Pro  
xD  
Foreasyremoval,Memory  
Deviceswillstickoutabit.  
Note:  
You can insert one USB flash drive, one CF card and one SD/MMC/MS Pro/xD  
card at the same time. Select different source by pressing the SOURCE (  
)
button in stop mode.  
If you cannot easily insert the memory card, you may have inserted it incorrectly.  
Flip over the card and try again.  
It does not support a USB hard disk mass storage device, multi-card reader or  
other USB computer peripheral.  
Insert any compatible memory card/USB flash drive with the front label facing the  
rear of the product. Do not force the memory card into the memory card slot.  
 
- 10 -  
VIEWING PHOTOS  
SlideShow  
1.Press the SOURCE (  
) button to select photo source.  
2.Start slide show: press the SLIDE SHOW (  
) button.  
3.Stop slide show: press the ENTER or EXIT button.  
Slide Show with Music background  
1.Press the SOURCE (  
2.Press the MUSIC button to select music mode.  
3.Use the buttons to highlight a music file, then press the ENTER button  
) button to select music source.  
/
to start music playback.  
4. Press the SLIDE SHOW (  
) button to enter slide show with the music background.  
5.Stop slide show: press the ENTER or EXIT button.  
Press the - VOL + buttons to adjust volume.  
You can only playback music and photos storing on same Memory Device only.  
ViewingPhotos  
1.Press the SOURCE (  
) button to select photo source.  
Thumbnail screen  
Note:  
JPEG and BMP photos  
are supported.  
2.Use the  
to playback the photo.  
3.Press the EXIT button to return to thumbnail display.  
/
/
/
buttons to select the photo, then press the ENTER button  
Press the WIDE / NORMAL (  
) button to change screen size between full  
screen or original screen.  
Press the ROTATE (  
Press the ZOOM (  
) button to rotate the photo by 90o  
) button to enlarge in the photo.  
 
- 11 -  
PHOTO VIEWING SETUP MENU  
1. Press the EXIT button to stop photo playback.  
2. Press the SETUP MENU button to enter setup menu.  
3. Use the  
/
buttons to highlight your selection, then press the ENTER button to confirm.  
4. Use the  
/
buttons to select the options, press the ENTER button to confirm the selection.  
5. Press the EXIT button to exit the setup menu.  
FullScreen  
SlideShowSpeed  
This option allows you to choose how your  
photos fit on the display.  
• On: to display photos in full screen  
automatically.  
• Off: to display photos in its original aspect  
ratio.  
This option allows you to choose the  
time elapsed between each photo  
during slide show playing.  
You are able to set the slide show  
speed to: 3, 5,10 or 20 seconds  
You can press the WIDE / NORMAL (  
)
button to change between full screen and original  
screen.  
SlideShowShuffle  
This option allows you to choose the  
shuffle On or Off for slide show.  
Slide Show Effect  
This option allows you to choose the  
animation effect during slide show  
mode:  
Off, Fade, Shutter, Cross Comb, Mask, Brick,  
Dissolve, Bar, Expansion or Random.  
On-screenLanguage  
Choose your preferred language.  
You are able to set the language to:  
English, French, Spanish or German.  
 
- 12 -  
LISTENING TO MUSIC  
Listening to Music  
1. Press the SOURCE (  
) button to select music source.  
2. Press and hold (few seconds) the MUSIC button to select MUSIC mode.  
Music files appear.  
Note:  
Support .mp3 music file.  
3. Use the  
/
buttons to highlight a music file, then press the ENTER button to start playback.  
During music playback:  
Press the  
Press the ENTER button to pause playback, press the ENTER button again to resume playback.  
Press the SLIDE SHOW ( ) button to enter photo slide show mode with the music background.  
Press the PHOTO button to enter photo mode with the music background.  
Press the EXIT button to stop music playback.  
/
buttons to perform fast forward/reverse.  
Press the SETUP MENU button to enter setup menu. (In the setup menu, you can customize  
the settings, copy or delete files, etc.)  
Music Repeat  
1. Press the EXIT button to stop music  
playback.  
2. Press the SETUP MENU button to enter  
setup menu.  
3. Press the  
Repeat.  
/
buttons to highlight Music  
4. Press the ENTER button to display the  
selections.  
5. Press the  
All or Off.  
/
buttons to highlight One,  
6. Press the ENTER button to confirm the selection.  
7. Press the EXIT button to exit the setup menu.  
 
- 13 -  
WATCHING VIDEO FILES  
WatchingVideoFiles  
1.Press the SOURCE (  
)button to select video source.  
2.Press and hold (few seconds) the VIDEO button to select VIDEO mode.  
Video files appear.  
Note:  
Support .avi video file.  
3.Use the  
/
buttons to highlight a video file you want to play, then press the  
ENTER button to start playback.  
During video playback:  
Press the  
/
buttons to perform fast forward/reverse.  
Press the ENTER button to pause playback, press the ENTER button again to  
resume playback.  
Press the EXIT button to stop video playback.  
Press the SETUP MENU button to enter setup menu. (In the setup menu, you  
can customize the settings, copy or delete files, etc...)  
Video Repeat  
1. Press the EXIT button to stop video playback.  
2. Press the SETUP MENU button to enter  
setup menu.  
3. Press the  
Repeat.  
/
buttons to highlight Video  
4. Press the ENTER button to display the  
selections.  
5. Press the  
or Off.  
/
buttons to highlight One, All  
6. Press the ENTER button to confirm the  
selection.  
7. Press the EXIT button to exit the setup menu.  
 
- 14 -  
COPYING / DELETING MEDIA FILES  
CopyingFiles  
You can copy media files among the internal memory, memory card or USB device.  
1. Press the EXIT button to stop photo, music or video playback.  
2. Use the  
3. Press the SETUP MENU button to enter setup menu.  
4. Press the buttons to highlight Copy File.  
,
,
,
buttons to highlight copy media file.  
/
5. Press the ENTER button to display the available device for copying file to (Make sure to  
connect the other memory card or USD device first.)  
6. Press the  
/
buttons to select an available device for coping file to, then press the  
ENTER button again to confirm the selection.  
7. Press the ENTER button to confirm "Yes". The selected file will be copied to the internal  
memory. (If select "No", then press the ENTER button to abort copying.)  
8. Repeat steps 2 - 7 to copy more files.  
9. Press the EXIT button to exit the setup menu.  
"To NAND" means copy file to the internal memory (  
).  
Note:  
When copying media files from other source to a memory card, make sure the memory card  
is not in writing-protect mode (or it is not locked).  
When copying files to the internal memory, if a warning message shows up indicating no free  
space for more media files, you may need to remove some already stored media files first  
before copying more media files. Please see the Deleting Files section below.  
Deleting Files  
1. Press the EXIT button to stop music, video  
playback or photo slide show.  
2. Use the  
,
,
,
buttons to highlight the  
media file that you want to delete.  
3. Press the SETUP MENU button to enter  
setup menu.  
4. Press the  
/
buttons to highlight the  
File to be deleted.  
5. Press the ENTER button to confirm. Then  
press the ENTER button again to confirm "Yes". The selected file will be deleted (or press the  
/
buttons to select "No", and then press the ENTER button to abort deleting).  
6. Repeat steps 2 - 5 to delete more files.  
7. Press the EXIT button to exit the setup menu.  
 
- 15 -  
TROUBLESHOOTING GUIDE  
SYMPTOM CAUSE(ANDREMEDY)  
Screen freezes.  
Turn off the unit and unplug the AC power adapter , then reinsert the AC  
power adapter and turn on the unit again.  
No power.  
Ensure that the AC power adapter is connected correctly.  
Cannot read the  
memory card.  
Ensure the memory card is not damaged.  
Ensure the media files are under the root directory of the memory card.  
Ensure the memory card is inserted to the unit correctly.  
Pull out the memory card and insert it again.  
Cannot read the USB  
flash drive.  
Ensure the USB flash drive is not damaged.  
Ensure the media files are under the root directory of the USB drive drive.  
Ensure the USB flash drive is connected to the unit correctly.  
Pull out the USB flash drive and insert it again.  
Cannot play photos.  
Ensure there are photos stored in the memory card / USB flash drive  
or internal memory.  
The size of the photo is too large.  
Photo display is not  
correct.  
Press the WIDE / NORMAL button to adjust the screen aspect ratio.  
Many digital cameras take photos in 4:3 aspect ratio but some in 16:9  
aspect ratio. Select a proper screen aspect ratio to view your photo.  
MAINTENANCE  
Cleaning the Unit  
Be sure to turn off the unit, disconnect the power adapter and remove all external connections  
before cleaning the unit.  
Wipe the unit with a dry soft cloth.If the surfaces are extremely dirty, wipe clean with a cloth that  
has been dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry  
cloth.  
Never use alcohol, benzene, thinner, cleaning fluid or other chemicals. Do NOT use compressed  
air to remove dust.  
Cleaning the LCD Screen  
Be sure to turn off the unit, disconnect the power adapter and remove all external connections  
before cleaning the LCD screen.  
Take good care of the LCD screen.The LCD screen is made of glass and is sensitive to abnormal  
force or hardware with sharp edges.  
If fingerprints or dust accumulate on the LCD screen, use a soft, non-abrasive cloth (such as a  
camera lens cloth) to clean the LCD screen.  
If the LCD screen is extremely dirty, and you want to use the LCD Cleaning Kit sold at various retail  
outlets, do NOT apply the cleaning liquid directly to the LCD screen. Moisten the cleaning cloth  
with the cleaning solution and wring out thoroughly, then clean the LCD screen, and wipe with a  
dry cloth again.  
Printed in China  
811-PF8191W010  
 
- 16 -  

Tekkeon Bluetooth Headset DVP5960 User Manual
Timex Heart Rate Monitor 811 095000 02 User Manual
Toastess Food Warmer TWT20 User Manual
Toshiba Laptop U305 S7449 User Manual
Tripp Lite Power Supply 3 Phase 10kVA User Manual
Uniden Cordless Telephone DECT1588 Series User Manual
Universal Electronics Universal Remote ITP100 User Manual
Vinotemp Refrigerator VT34 User Manual
Weber Gas Grill 43267 User Manual
W Linx Technology Satellite Radio TXE 315 KH User Manual