S E R I E S
STARFIRE-10
10-Inch Powered Subwoofer
STARFIRE-12
12-Inch Powered Subwoofer
w w w . c h r y s a l i s a c o u s t i c s . c o m
w w w . c h r y s a l i s a c o u s t i c s . c o m
TABLE OF CONTENTS
Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Crossovers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Interconnect Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Care of Your Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Protection Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Troubleshooting and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Chrysalis Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Starfire Series Manual
ii
w w w . c h r y s a l i s a c o u s t i c s . c o m
CONGRATULATIONS
Congratulations on your purchase of a Chrysalis Starfire™ subwoofer system. This system represents the state-of-the-art in home audio
reproduction and will provide you with years of listening pleasure when properly cared for. Read and follow this instruction manual to
insure safe and proper system connection and operation.
Caution!
Please observe the following instructions to insure safe and proper system operation.
Note: Do not leave unit in direct sunlight or use in high humidity environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or
amp chassis cover. Please observe all warnings on the equipment itself. There are no user serviceable parts inside. Please refer all service
questions to your authorized Chrysalis dealer.
Prior to Installation:
Please unpack the system carefully. This unit is heavy. Use caution when lifting or moving to avoid injury. Please save the carton and all
packaging materials for future use. Packing this unit in any other carton may result in severe damage when shipping. Record the serial
number in the space provided on page 13 for future reference.
Product Features
• A single driver consisting of either:
- 10” (8.2” piston diameter) subwoofer with 2.0” high-temp voice coil and 89.6 ounce (5.6 lb) motor structure or,
- 12” (9.7” piston diameter) subwoofer with 2.0” high-temp voice coil and 89.6 ounce (5.6 lb) motor structure
• Adjustable (50 to 200 Hz) low-pass crossover with a 12 dB/octave slope
• Line-level (RCA) inputs
• Speaker-level inputs and outputs with spring loaded terminals
• Signal sensing auto turn on/off
• Variable volume control
• Selectable phase control (0° or 180°)
• Green power on/ Red power standby mode indicator LED
Prepare for Installation
Your new Chrysalis subwoofer provides for a number of installation options. Read all the installation information below in order to
determine which installation option is best for your system. Remember to perform all installation procedures with system power turned
off to prevent possible damage.
Starfire Series Manual
1
w w w . c h r y s a l i s a c o u s t i c s . c o m
Placement
The first step in installing your new Starfire is to determine where it will be placed in the room. Unpack the system carefully and use the
following guidelines in order to find the best room placement option.
True subwoofers operate at extremely low frequencies which are primarily omni-directional. Keep in mind that frequency response and
output level can be drastically influenced by placement, depending on the acoustic properties of the listening room. To obtain optimum
output from your subwoofer, place it within a foot of a corner. This location will offer the greatest output levels and optimum low frequency
extension. If at all possible, your subwoofer should be placed along a wall. The worst location for a subwoofer is typically far away from any
walls and close to the center of your room. Avoid these locations when possible. When using a pair of Chrysalis subwoofers in stereo, it is
preferable to place each subwoofer near the satellite of the same channel.
Depending on the size and type of furnishings in the room, perfect placement may not be possible. Finding the best location within your
environment will likely require some experimentation. We suggest you experiment with the location during setup to find what sounds best to
you when seated in your typical listening position.
Regardless of where you install your Chrysalis subwoofer, it must remain in an upright position (woofer facing forward). Using, shipping or
storing the subwoofer in any other position for an extended period of time may result in damage to the unit not covered by warranty.
Caution!
This subwoofer has electronics built into the cabinet. Do not place the cabinet next to sources of heat such as furnace registers, radiators, etc.
Do not place the unit near sources of excessive moisture, such as evaporative coolers, humidifiers, etc. The power cord should be routed in such
a way that it will not be walked on, pinched or compressed in any way that could result in damaging the insulation or wire.
Your Chrysalis Starfire subwoofer is NOT magnetically shielded, primarily for use with modern video monitors. Should you find it necessary
to use it with an older CRT monitor or TV, keep it at least two feet from the monitor. Experiment for correct distance by minimizing
distortion of the picture and colors.
INSTALLATION
Inputs
Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when connecting your subwoofer to a
pre-amp, signal processor (such as LFE out), line-level crossover, or receiver with pre-amp level outputs. When using the line level jacks, some
receivers may not provide enough signal to have the unit’s auto-on feature operate properly. Additionally, this lack of signal may also cause the
subwoofer to produce less output than it is capable of.
Starfire Series Manual
2
w w w . c h r y s a l i s a c o u s t i c s . c o m
To alleviate this condition, we recommend the following steps:
1) If using line level jacks, BOTH THE LEFT AND RIGHT INPUT SHOULD ALWAYS BE USED – never use just the left
or just the right input. If the subwoofer’s input comes from the LFE channel of your receiver, use a “Y” splitter to supply the
single input to both connectors for the Left and Right subwoofer inputs. If using line level connections from a preamp or signal
processor, use both Left and Right inputs from your preprocessor or preamp and connect them to the Left and Right inputs on
your subwoofer.
2) If using a receiver with LFE out, be sure the LFE channel is sending adequate signal to the subwoofer. We recommend setting
the subwoofer’s level to the 9 o’clock position (the 1/4 volume setting) and then adjust the LFE channel on your receiver or
processor to achieve the desired bass output. See your receiver or processor’s owner’s manual for more information.
The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplifier, integrated amplifier, or receiver. Your amplifier section
will notice no additional loading effects when you use these inputs due to their very high impedance. If using the SPEAKER LEVEL inputs,
you DO want to connect both channels, since different bass information might be present in each channel going to your main speakers.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections simultaneously!
Caution!!!
To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections - red (positive) to red, and black
(negative) to black. Be sure all connections are tight, and that there are no loose strands or frayed wires.
Volume Control
This control allows you to balance the output from the subwoofer to the main speakers in your system. This control should be set to achieve
similar output levels from both the main speakers and subwoofer when listening to music. A good starting point for the volume control is
two or three graduations from minimum.
Warning:
Some manufacturers preset their receivers with the Sub-Out channel signal at a minimum level. It is very important to verify that your receiver
Sub-Out channel is set to the same output level as your front right and left channels. Refer to your receiver manual for the individual channel level
adjustment procedure. If your receiver Sub-Out channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or
distorted, and the Auto On/Off feature may not operate properly.
Low-pass Crossover - 50 to 200 Hz
As noted above, all inputs sum the left and right channels together, with the resulting signal passing through an adjustable low-pass crossover
before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer’s frequency response from 50 to 200 Hz.
The subwoofer’s response will begin rolling off above the frequency you set this control to. You should set the crossover frequency to obtain a
smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with limited
low frequency output, you may wish to choose a higher frequency (such as 100 - 120 Hz) than you would with larger speakers which have
greater low frequency output. With larger speakers, you might start with this control set lower, such as 80 Hz.
Starfire Series Manual
3
w w w . c h r y s a l i s a c o u s t i c s . c o m
Phase Adjustment - 0°/180°
This control allows you to “reverse” the phase of the subwoofer’s output signal 180° to correct for any possible mismatch and resulting
cancellation between the subwoofer and your main speakers/amplifier. To adjust, simply listen to the system with music playing, then depress
the phase switch from one position to the other and listen for a change in mid-bass frequency output. The correct position will have a greater
amount of apparent mid-bass frequency output.
For all installations, experiment with the phase switch to determine the setting (0 or 180 degrees) that produces the most mid-bass. If the
settings sound similar, we recommend the “0” position.
Auto Turn on Function
The subwoofer will turn itself on automatically when an audio signal is present. If no signal is present for approximately eight minutes, the
unit will switch to standby mode (Red LED). While in standby mode, your subwoofer will draw very minimal power.
Warning:
If the Sub-Out channel signal level from your receiver is too weak, this feature will not operate properly. See VOLUME CONTROL section
on previous page.
Starfire Series Manual
4
w w w . c h r y s a l i s a c o u s t i c s . c o m
REAR PANEL CONNECTIONS
Figure 1.Starfire Rear Panel Connections
Figure 1 shows the connections on the rear panel of the Starfire. Following are brief descriptions of the connections described in Figure 1.
More detail of these connections can be found below:
(1)
SPEAKER LEVEL INPUT terminals - Connect these input terminals to the speaker output terminals of your amplifier
or receiver.
(2)
(3)
(4)
SPEAKER LEVEL OUTPUT terminals - The speaker-level signal to the front speakers is output from these terminals.
LINE INPUT jacks - Connect these jacks to the LINE OUT jacks of the amplifier.
LOW-PASS CROSSOVER - Use this knob to select the high-frequency range at which you wish to cut-off the signal to
the subwoofer.
Starfire Series Manual
5
w w w . c h r y s a l i s a c o u s t i c s . c o m
(5)
Power indicator - Red: Unit is in standby mode. Green: Unit is in operation mode. (automatically turns to STANDBY mode if
no signal for eight minutes)
(6)
(7)
PHASE switch - Select the switch position at which you hear a louder mid-bass sound.
VOLUME LEVEL knob - Use this knob to adjust the output level of the subwoofer.
CROSSOVERS
Receiver/Processor Subwoofer Outputs
The Chrysalis subwoofer is designed to operate using the full range audio signal for input when using the built-in crossover. Many home
theater processors/receivers (Dolby Digital™, DTS™, THX™) have a “subwoofer out” jack (sometimes labeled “LFE”) that is internally filtered,
settable at the receiver/processor, and designed to be used with a powered subwoofer. In some installations, it may be beneficial to use
BOTH the Chrysalis crossover and the receiver/processor crossover, resulting in a steeper ultimate crossover slope. In some rare cases,
combining both an external crossover and the one internal to the subwoofer may result in low output and increased noise. In these
installations you may need to bypass the crossover in either the processor or your Starfire subwoofer, or simply setting one crossover to a
higher frequency (such as 120 Hz) will restore maximum performance.
(Refer to Figure 2a Line-Level Subwoofer Connection Diagram and Figure 2b Speaker-Level Subwoofer Connection Diagram, pages 7 and 8 for
connection diagrams.)
Starfire Series Manual
6
w w w . c h r y s a l i s a c o u s t i c s . c o m
Figure 2a. Line-Level Subwoofer Connection Diagram
Starfire Series Manual
7
w w w . c h r y s a l i s a c o u s t i c s . c o m
Figure 2b. Speaker-Level Subwoofer Connection Diagram
Starfire Series Manual
8
w w w . c h r y s a l i s a c o u s t i c s . c o m
INTERCONNECT CABLES
When installing your new Chrysalis subwoofer using the line level connections, you should always use shielded phono cables. There are
many high quality cables available today. It is recommended that you keep the length of cable as short as possible to avoid any potential
noise problems.
When using speaker level connections, use a high quality speaker cable that mates well with the connectors. Be very careful to avoid any loose
strands or frayed wires that may result in a short, which may damage your equipment. Cables of extremely large size are typically not
required. Extremely large gauge wire may not properly fit in the binding posts, resulting in a poor connection and possible short circuits.
CARE OF YOUR SUBWOOFER
Your Chrysalis subwoofer does not require any regular maintenance. Normal dusting or cleaning of the surface for appearance purposes is all
that is required. We suggest you avoid any harsh detergents or chemicals when cleaning the cabinet. Abrasives, detergents, or cleaning
solutions may damage the finish on the cabinet. We recommend using only a damp cloth to clean the cabinet.
During normal conditions, your new subwoofer may be left on continuously without any problems. The unit is equipped with a signal-
sensing turn on/off that will automatically turn on the unit when a signal is present at the inputs and turn off the unit after several minutes
when there is no longer any signal at the inputs.
PROTECTION CIRCUITRY
Your new subwoofer is equipped with circuitry to provide maximum performance with greatest reliability.
The unit is protected against:
1) Overheating the amplifier.
2) Excessive drop in power line voltage.
If either of the above should happen, you should reduce the volume setting or shut the unit off until normal operating conditions return. You
may also want to plug the unit into a different wall outlet, as dropping power line voltage will be most noticeable under strenuous conditions
and may result in the unit shutting down intermittently.
Starfire Series Manual
9
w w w . c h r y s a l i s a c o u s t i c s . c o m
TROUBLESHOOTING AND SERVICE
Before seeking service for your amplifier or subwoofer, please re-check all systems. Following is a simple troubleshooting guide to assist you.
1. Verify that the unit is plugged in and power outlet used is active.
2. Is the power switch on?
3. Is the unit receiving an input signal from your source?
4. Have all controls (volume, crossover, phase, etc.) been properly set?
5. If the unit has been running at high levels, one of the protection circuits may be engaged. Has the amplifier overheated?
6. Make sure the speaker wires are fully inserted into the spring clip connectors and that no wires are touching
from one terminal to another.
If the protection circuitry is active, the unit may cycle on and off until operating parameters return to normal. Under more serious conditions,
the unit may shut off completely. Normal operation should return upon cooling, but you may be required to turn the power off and then on
again to reset the unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged
2. The unit does not appear to operate normally or exhibits a marked change in performance
3. The unit has been exposed to water
4. Some part of the chassis or circuitry is physically damaged
Starfire Series Manual
10
w w w . c h r y s a l i s a c o u s t i c s . c o m
SPECIFICATIONS
SPECIFICATIONS
STARFIRE-10
STARFIRE-12
Woofer
10” (24.5 cm)
12” (30.5 cm)
forward firing
foward firing
(8.2” piston diameter)
(9.7” piston diameter)
Amplifier:
Class D
150 watts Dynamic/
250 watts RMS Power
165 watts Dynamic/
275 watts RMS Power
Cabinet Design
Acoustically neutral,
downward-firing port
Acoustically neutral,
downward-firing port
Frequency Response
32 -140 Hz
(+/-3 dB)
29 - 140 Hz
(+/-3 dB)
Voice Coil
2” copper-wound
Coated Fiber
89.6 oz. (5.6 lbs)
Full Range
2” copper-wound
Coated Fiber
89.6 oz. (5.6 lbs)
Full Range
Cone
Magnet Structure
Speaker-Level Pass-Through
Low-Pass Crossover
Outputs
50 - 200 Hz
50 - 200 Hz
Left and right speaker
level pass-through
Left and right speaker
level pass-through
Inputs
RCA Line Level, LFE and
Speaker Level inputs
RCA Line Level, LFE and
Speaker Level inputs
Phase
0° or 180°
0° or 180°
Yes
Auto On/Off
Removable Grill
Video Shielding
LED Power Indicator
Input Impedance
Yes
Yes
Yes
No
No
Yes
Yes
65K ohm (for LINE INPUT jacks)
1.2K ohm (for SPEAKER LEVEL INPUT terminals)
Sensitivity Speaker-Level
Line
1.0V
100 mV
1.0V
100 mV
Power Supply
120V, 60 Hz AC
120V, 60 Hz AC
Cabinet (H,W,D)
(cm) with grille
13.75” x 12.75” x 14.4”
35 x 32 x 37
15.4” x 14.4” x 17.9”
39 x 37 x 46
Warranty (parts/labor)
Three years (electronics - parts and labor)
Five years (drivers - parts and labor)
Shipping Weight (approx.)
30 lbs. (17 Kg)
36 lbs. (20 Kg)
Specifications are subject to change without notice.
Starfire Series Manual
11
w w w . c h r y s a l i s a c o u s t i c s . c o m
CHRYSALIS PRODUCTS
BassMatrix™ Series
BassMatrix-10
BassMatrix-12
Photon™ Series
Photon-8
Photon-10
Starfire™ Series
Starfire-10
Starfire-12
Starfire Series Manual
12
w w w . c h r y s a l i s a c o u s t i c s . c o m
FOR YOUR RECORDS. . .
Date Purchased____________________________________________________________________________
Dealer__________________________________________________________________________________
Serial #_________________________________________________________________________________
*NOTE: Please complete and return your warranty card within ten (10) days or
LIMITED WARRANTY - U.S. AND CANADA ONLY
CHRYSALIS ACOUSTICS (“CHRYSALIS”) warrants all electronics for a period of three years, drivers for a period of five years, and full
range speakers for a period of five years. All CHRYSALIS products have a warranty from the date of purchase against defects in materials and
workmanship subject to the following conditions:
1. CHRYSALIS is not responsible for defects which result from the use of an amplifier or controller other than the one originally
supplied with the unit (subwoofer) or defects which result from modifications or repairs made by any component of the system by
anyone other than a CHRYSALIS factory authorized service representative.
2. This warranty is void if any repairs or service covered by the terms of this warranty are made to any component of the system by
anyone other than a CHRYSALIS factory authorized service representative.
3. CHRYSALIS is not responsible for damage caused by accidents, abuse, misuse, natural or personal disaster or unauthorized
modification. The CHRYSALIS products are not intended for professional or commercial use and CHRYSALIS is not responsible
for damage resulting from such use.
4. The CHRYSALIS product warranty is limited to units that are purchased from authorized CHRYSALIS dealers and finalized
within authorized dealer locations.
5. This warranty is nontransferable under any condition.
6. Use of this product outside the U.S. and Canada voids this warranty.
TO OBTAIN SERVICE
Information regarding service may be obtained from the dealer from whom you purchased the unit, or by contacting CHRYSALIS customer
service. Warranty service must be performed by a CHRYSALIS factory authorized service representative within the warranty period set forth
above. If CHRYSALIS determines the unit is defective, CHRYSALIS will, at CHRYSALIS’s option, repair or replace the product at no
charge if the product is forwarded prepaid to a factory authorized service representative. Products forwarded to the factory authorized service
representative should be shipped securely and properly packaged, insured and freight prepaid.
WARRANTY OUTSIDE THE UNITED STATES AND CANADA
The Warranty of this product if it is sold to a consumer outside of the United States or Canada shall comply with applicable law and shall be
the sole responsibility of the distributor that supplied this product. To obtain any applicable warranty service, please contact the dealer from
which you purchased this product, or the distributor that supplied this product.
Starfire Series Manual
13
C h r y s a l i s A c o u s t i c s
A Velodyne Company
345 Digital Drive
Morgan Hill, CA 95037
408.465.2888 voice
408.779.9227 fax
408.779.9208 service fax
w w w . c h r y s a l i s a c o u s t i c s . c o m
63-STARFIRE Rev D NOV08
|