VEC259
CORDED, CORDLESS,
RECHARGEABLE COMPRESSOR, INFLATOR
AND LANTERN LIGHT COMBO
OWNER’S MANUAL
& WARRANTY INFORMATION
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ
AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN INJURY AND/OR PROPERTY DAMAGE.
4140 SW 28th Way, Ft. Lauderdale, FL 33312
PH: 954-584-4446 • TOLL FREE: 866-584-5504 • Fax: 954-584-5556.
4140 SW 28th Way, FT. LAUDERDALE, FL 33312
Tel 954-584-4446 • TOLL FREE: 866-584-5504 • Fax 954-584-5556
MS062703
The compressor on/off switch controls operation of the compressor. It can be
conveniently depressed and released to control inflation. An exact pressure is obtained
by observing the gauge and releasing the trigger when the correct pressure is
achieved. For longer inflation operations, the trigger lock can be moved laterally to
lock the trigger in the ON position. Pushing the trigger lock to the opposite direction
releases the trigger and stops inflation.
1.
INTRODUCTION
Congratulations on selecting the Vector AirPro™ Model VEC259 Compressor/Inflator
and Lantern Light combo. This system is an advanced, high-pressure (up to 260 PSI),
multi-use air compressor system with unique features that set it far above the value and
utility of ordinary compressors for mobile use. It is supplied with a standard tire valve
chuck for filling auto, truck, bike, and motorcycle tires. Additionally, two different
adapters are supplied to inflate soccer balls, footballs, and popular inflatables. These
adapters are conveniently stored in a hatch in the compressor body. It is powered
from its own snap-on/off powerful battery, to be used anywhere it is needed. It can
also operate from a standard 12 volt DC electrical system found on: trucks, cars, boats,
airplanes, RVs and tractors, using the supplied DC power adapter. A supplied stan-
dard 120 volt AC charger recharges the battery when required. Typically, up to three
completely flat tires can be inflated before the battery pack has to be recharged.
2.
ADDITIONAL KEY FEATURES
• Trigger switch with lock to allow hands free operation
• Corded - includes a DC power adapter for use with standard 12 volt DC power
supply
• Battery pack includes non-spillable, maintenance-free, heavy duty, sealed,
high-density, lead-acid battery
• Requires no maintenance (other than recharging and cleaning) for optimum
operation
The inflator and light share the battery pack and DC power adapter. The inflator
is used to inflate and deflate air beds, balls, rafts, etc. The lantern is versatile and
provides a spotlight, fluorescent area light, and emergency flasher.
•
Supplied 120 volt AC charger is Underwriter Laboratories (UL) safety tested and listed
• Battery charging LED on battery automatically activated during AC recharge
• Analog pressure gauge to 260 PSI compressor
• Nozzle hatch for storing nozzles in compressor
• 3 nozzles for inflator
Extra battery packs can be purchased, if completely cordless operation is required
(part VEC194). Operating these appliances with the DC power adapter is ideal for
use with Vector 12 volt DC cordless, portable, rechargeable DC power supplies, if
extended operating time in the field is required.
FIGURE 2
NOZZLE HATCH COVER
NOZZLE HATCH COVER
HOSE RETAINING RING
NOZZLES
COMPRESSOR OUTLET
RIBBED BRASS FITTING
TRIGGER LOCK
TRIGGER SWITCH
PRESSURE GAUGE
COMPRESSOR HOSE
CAUTION:
This battery pack is delivered in a partially charged state - you must fully charge
it before using it for the first time. Initial AC charge should be for 24 hours. Refer
to Section 6 for use of AC adapter and detailed charging instructions.
TIRE CHUCK
3
4
The DC power adapter has a fused DC plug and connecting cord stored inside the DC
power adapter. To use the DC power adapter, first remove the DC plug from it’s
storage in the adapter. Remove the cord from storage, and connect the DC power
adapter to the compressor. Make sure it snaps into position. Connect the DC plug to a
12 volt DC source. To remove the DC power adapter, press the release buttons. Put the
DC plug and cord in the adapter for storage after use.
3.
ATTACHING THE COMPRESSOR’S AIR HOSE
The air hose is supplied as a separate item from the compressor body. The hose has
a ribbed brass fitting at one end and a standard tire chuck at the other end. To use the
hose it must first be connected to the compressor outlet. Loosen the hose retaining ring
(counterclockwise), insert the hose fitting into the short, rubber sealing sleeve. Make
sure the hose fitting is inserted fully into the sleeve. Partially tighten (clockwise) the
hose-retaining ring and push the fitting in further. Do this two or three times until the
fitting is firmly attached and the ring is firmly tightened.
FIGURE 3
CONTACT
WARNING:
Improperly attached hoses or nozzles can fly out under compressor pressure.
Make sure the connections are tight.
WARNINGS:
FUSED DC PLUG
1. There is risk of dust or dirt being released if the compressor hose or nozzles
are not clean when the compressor is turned on.
2. Wearing protective goggles while operating this compressor can protect
eyes from flying particles of dust and dirt. Failure to follow instructions may
cause property damage, and/or personal injury.
3. Keep out of reach of children.
RELEASE BUTTON
4.
POWERING THE COMPRESSOR, INFLATOR OR LAMP
5.
CHARGING/RECHARGING THE BATTERY PACK
The appliances can be powered either from a supplied battery pack or from a
supplied DC power adapter.
Lead acid batteries require periodic charging to maintain a full charge and to ensure
good battery life. All lead acid batteries suffer from self-discharge over time, and more
rapidly when they are at higher temperatures. Therefore, these types of batteries need
periodic charging to replace energy lost through self-discharge. When the battery pack
is not in use, Vector recommends that the battery is recharged at least every 60 days.
4.1
POWERING FROM THE BATTERY PACK
The supplied battery pack powers the compressor or inflator for a short duration,
cordless operation. The battery pack should be fully charged initially before use (see
paragraph 5 for charging instructions.
All batteries must be recharged as soon as possible after each use. If a battery is allowed
to remain in a discharged state, battery life will be reduced.
To connect the charged battery pack to either the compressor or lamp, align the
battery pack so the battery release buttons snap onto the appropriate appliance. The
battery pack fits only one way to ensure correct polarity of the contacts. To remove the
battery pack, press the battery pack release buttons.
NOTE:
Recharging battery after each use will prolong battery life; frequent heavy
discharges between recharges will reduce battery life. Overcharging will reduce
battery life. Never charge for more than 24 hours.
4.2
DC POWER ADAPTER USE
The time required to fully recharge the battery pack depends on the charge status
of the battery after it’s use. If the battery is discharged from recent use, recharge the
battery for 8 hours.
The DC power adapter can power an appliance for a longer period of time from an
external 12 volt DC power source.
5.1
AC RECHARGE OF BATTERY PACK
AC recharge requires the use of the supplied AC/DC adapter. The AC adapter
must be powered from 110/120 volt AC, 60 Hz North American standard AC recep-
tacles. The battery pack must be removed from the compressor (applicance) body to
gain access to the recharge port.
5
6
CONTACT
FIGURE 4
IMPORTANT:
Always leave the tire chuck thumb latch in the open position when storing unit.
RECHARGE PORT
RECHARGE LED
6.2
INFLATE OTHER ARTICLES (WITHOUT VALVE STEM)
Inflation of items, others than tires, requires use of one of the nozzles (adapters).
A nozzle can be attached to the tire chuck, or it can directly be connected to the
compressor’s outlet, if the hose is removed.
To attach a nozzle to the tire chuck, open the nozzle hatch cover and remove the
required nozzle. Place the tire chuck over the nozzle fitting and secure by moving the
chuck thumb latch so it is parallel with the hose. Make sure the nozzle is clean and
secure before turning on the compressor. After use, release the nozzle from the chuck
by lifting the latch. Return the nozzle to the nozzle hatch.
RELEASE BUTTON
110/120 VOLT AC WALL
ADAPTER WITH CORD
To attach a nozzle directly to a compressor.
1. Remove the hose from the compressor outlet by loosening (counterclockwise) the
hose retaining ring and sliding out the ribbed brass fitting.
To remove the battery pack from the appliance body for charging, make sure the
trigger switch is OFF. Press both battery pack release buttons at the same time. Pull the
battery pack down away from the appliance body. Insert the barrel connector of the
AC adapter into the battery pack’s receptacle (recharge port). Plug the AC adapter
into a 120 volt AC standard household receptacle. Observe the red LED lights. Charge
for the recommended time. Do not overcharge! Disconnect and store the AC recharge
adapter from the battery pack and AC source when not in use.
2. Insert the selected nozzle into the compressor outlet and secure it by tightening the
hose retaining ring.
3. After using the compressor, remove and store the nozzle in the nozzle hatch.
Refer to “Typical Inflation Times” for approximate pressure and time. Small items like
volleyballs, footballs, etc. inflate very rapidly.
4. Insert nozzle (e.g needle) into item to be inflated and inflate to desired pressure.
5. Turn on compressor switch - inflate to desired pressure or fullness.
6.
COMPRESSOR/TIRE INFLATOR
7.
TYPICAL INFLATION TIMES FOR COMPRESSOR USE
This 12 volt DC compressor is the ultimate compressor for all vehicles, trailer tires and
recreational inflatables. Three different sized nozzles are supplied.
The following are approximate pressure and inflation times for various items:
IMPORTANT:
WARNINGS:
Read safety instructions carefully to avoid possible injury or property damage.
Always follow tire manufacturers recommendations for pressure on item to be inflated.
WARNINGS:
The compressor is capable of inflating to 260 pounds per square inch (PSI)
pressure (approximately 18 kg/cm). To avoid over-inflation, carefully follow
instructions on articles to be inflated. Never exceed recommended pressures.
Bursting articles can cause serious injury. Always check pressure with the
pressure gauge. Never leave compressor unattended while in use. Allow unit to
cool for five minutes after 10 minutes of continuous operation.
VEHICLE AND TRAILER TIRES
TIRE SIZE
PRESSURE
26 psi
30 psi
30 psi
50 psi
TIME FROM “0” PRESSURE
2.50 min.
155/80R 13"
185/70R 14"
235/75R 15"
235/85R 16"
4.50 min.
6.50 min.
16.00 min.
BICYCLE TIRES
TIRE SIZE
6.1
TIRE INFLATION OR PRODUCTS WITH A VALVE STEM
PRESSURE
10 psi
TIME FROM “0” PRESSURE
40 sec.
1. Place connector (chuck) on valve stem.
27 x 1" racing
2. Push connector toward valve stem and close thumb latch.
3. Make sure connector is pushed onto valve stem as far as possible before closing
thumb latch.
INFLATABLE ARTICLES
ITEMS
PRESSURE
13 psi
9 psi
TIME FROM “0” PRESSURE
24 seconds
Football
4. Turn on the compressor (for larger items the trigger can be latched).
5. Observe pressure with the pressure gauge.
6. When desired pressure is reached, open thumb latch and remove connector from
valve stem.
Basketball
20 seconds
6 seconds
Volleyball
5 psi
7. Turn off compressor power switch.
7
8
FIGURE 6
SPOTLIGHT
8.
INFLATING
1. Connect the inflator/deflator to either the battery pack or the DC power adapter.
2. Be sure the appropriate nozzle head is attached to the tapered inflating port of the
inflator/deflator unit. Push the nozzle onto the inflation port to attach. The inflat-
ing port can be identified by location. It is on the side of the unit.
3. Position the nozzle against the valve of the inflatable item. Turn on the unit, and
inflate the item to desired firmness. After inflation, move the nozzle away from the
valve and turn the switch OFF.
SPOTLIGHT TRIGGER SWITCH
(LATCHING)
SCREW
SLIDE SWITCH
FLUORESCENT/OFF/
EMERGENCY FLASHER
8.1
DEFLATING
1. Pull off the nozzle from the inflating port of the unit and reinstall it at the
deflating port of the inflator/deflator (on the top of the unit). Press the
nozzle to attach.
2. Power the Inflator with either the battery pack or the DC adapter.
3. Position the nozzle against the valve of the inflated item. Turn on the
unit and deflate the item.
EMERGENCY FLASHER
FLUORESCENT LAMP
12V DC
ACCESSORY OUTLET
NOTE: If the inflatable item’s air valve is equipped with a safety flap, it maybe
necessary to hold the flap open with a pencil or similarly shaped object
to deflate the item.
9.
LANTERN LIGHT
The lantern light is actually three lights in one. The spotlight provides a bright focused
light; a bright, long lasting fluorescent lamp provides general area lighting, and a 3
light LED flashes on and off for emergencies.
The main quartz-halogen spotlight is controlled on and off by a latching trigger switch
on the handle. The lantern light is powered by either the 12 volt battery pack or the
12 volt DC power adapter.
BATTERY PACK OR
DC POWER ADAPTER
Approximate continuous runtimes on a fully charged battery are:
A 12 volt DC accessory outlet is located on the side of the unit. This permits cell phone
recharging or operation of other 12 volt DC appliances. If the battery pack is installed
(3 amp hour, 12 volt battery or 36 watt hours), appliance wattage should be limited
to prevent rapid battery rundown.
Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 hours
Fluorescent light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 hours
Emergency flasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 hours
Recharge the battery pack after each use. (Refer to Section 5 for details.)
9.1
PARTS REPLACEMENT LANTERN LIGHT
Replaceable parts for the lantern light are:
The quartz halogen bulb and the fluorescent tube.
9
10
4. Push the pins on the new bulb into the socket and make sure the bulb is
fully inserted.
FIGURE 6 - LANTERN LIGHT PARTS REPLACEMENT
5. Replace the lens and bezel.
6. Tighten (clockwise) the bezel until it is snug.
7. Test the light for proper operation by turning it on and then off.
BULB
REFLECTOR
9.3
FLUORESCENT LAMP REPLACEMENT
The bulb type is a standard 4 watt, F4T5/D fluorescent tube. A replacement bulb can be
purchased from local lighting, hardware or camping stores. The fluorescent lamp tube
can be replaced after the front vertical lens is removed. The procedure follows:
BEZEL
LENS
1. Remove the battery pack or DC adapter. Using a small Phillips screwdriver,
unscrew (counterclockwise) the small screw at the top of the lens.
2. Slide the lens down from the top of the unit and remove the lens. Set the lens aside.
3. Remove the fluorescent tube by turning one-quarter turn so pins at both ends of
the tube are released from the sockets.
SCREW HOLE
(SCREW REMOVED)
4. Set the defective tube aside for proper disposal.
5. Put in a new tube, being careful to keep the bulb pins from bending.
6. Rotate the tube one-quarter turn to lock the pins into the sockets.
7. Check the new tube to make sure it is secure in the sockets.
8. Replace the lens, and slide it towards the top of the unit. The screw holes should
align.
9. Replace the small screw and carefully tighten with the Phillips screwdriver.
10. Follow local ordinances for fluorescent bulb disposal.
REMOVE LENS
10.
MAINTENANCE/REPLACEMENT PARTS
For replacement parts (batteries, DC power adapters, AC charging adapters, cables,
etc.), contact Vector technical support: (954) 584-4446 or toll free (866) 584-5504.
Periodically, cables, hose, nozzles, and connectors should be inspected for damage,
corrosion, dust and dirt. If surfaces are dirty, they can be wiped clean with a cloth
moistened with water and a drop of detergent. Battery pack contacts can be wiped
clean with a dry cloth.
9.2
QUARTZ HALOGEN BULB REPLACEMENT
The bulb is a 15 watt, 12 volt, G4 projection type. This type bulb has two connector
pins that plug into a socket. The procedure follows:
1. Unscrew the bezel (counterclockwise) and remove the bezel and lens.
2. Hold the reflector in place against the body of the lamp and pull the bulb straight out.
Note the location of two socket holes that accept the bulb pins.
11.
BATTERY REPLACEMENT
3. Using a clean cloth, remove the new bulb from the packing material.
The battery in the battery pack should be replaced with a new one when the operating
capacity is reduced to about one half or the ability to inflate one and one half
average sized automobile tires. Make sure that the battery is fully charged before
determining that the battery pack should be replaced. Contact Vector technical
support and ask for part VEC194. This battery pack is also used with other Vector
products that include portable inflators and spotlights. For more details, please contact
our technical support department toll free (866) 584-5504.
NOTE: Do not touch the new bulb with bare hands; oil from fingers can cause
premature failure of these bulbs. If the bulb is touched, clean the bulb
with alcohol and a clean cloth after the bulb is installed.
11
12
11.
SPECIFICATIONS
FOR COMPRESSOR:
1 YEAR LIMITED WARRANTY PROGRAM
Battery . . . . . . . . . . . .12 volt, 3 Amp hour, non-spillable, sealed lead acid
Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260 PSI maximum
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.82 lbs (.83 kg)
Height w/battery . . . . . . . . . . . . . . . . . . . . . . . . .11.25 inches (28.57 cm)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.0 inches (10.16 cm)
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 inches (17.78 cm)
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty,
other than those described herein.
This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of
defects in materials and workmanship for one year from the date of purchase without additional
charge. The warranty does not extend to subsequent purchasers or users. Vector Manufacturing,
Ltd. will not be responsible for any amount of damage in excess of the retail purchase price of the
product under any circumstances. Incidental and consequential damages are specifically excluded
from coverage under this warranty.
LANTERN LIGHT:
Quartz Halogen Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15W, G4
Fluorescent Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F4T5/D
This product is not intended for commercial use. This warranty does not apply to accessories or
damage to units from misuse or incorrect installation. Misuse includes wiring or connecting to
improper polarity power sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage
prepaid to Vector Manufacturing. Any defective product, other than accessories, that is returned
to Vector Manufacturing within 30 days of the date of purchase will be replaced free of charge. If
such a product is returned more than 30 days but less than one year from the purchase date,
Vector Manufacturing will repair the unit or, at its option, replace it free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at Vector
Manufacturing’s option. A unit may be replaced with a new or reconditioned unit of the same or
comparable design. The repaired or replaced unit will then be warranted under the terms of the
remainder of the warranty period. The customer is responsible for the shipping charges on all
returned items after 30 days. During the warranty period, Vector Manufacturing, Ltd. will be
responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting
from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due
to usage or exposure to sunlight), accidents, damage during shipping to our service facility,
alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions for
care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department (954) 584-
4446 or toll free (866) 584-5504 for general repair information and charges if applicable.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow
limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the exclusions or limitations stated herein may not apply. This warranty
gives the purchaser specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing technical support
by telephone, fax or mail. We suggest that you keep the original packaging in case you need to
ship the unit. When returning a product, include your name, address, phone number, dated sales
receipt (or copy) and a description of the reason for return and product serial number. After
repairing or replacing the unit, we will make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector
Manufacturing. Enter “VEC259” as Model and "Corded, cordless, rechargeable compressor and
lantern light combo" as Product Type. All Vector Manufacturing, Ltd. products must be registered
within 10 days of purchase to activate this warranty. Mail the completed registration form, along
with a copy of the original sales receipt to:
ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.
4140 SW 28th Way, Ft. Lauderdale, FL 33312
PH: 954-584-4446 • TOLL FREE: 866-584-5504 • Fax: 954-584-5556.
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.
13
14
|