VSP-45 ohm
Issue 6
45 OHM TALKBACK INTERIOR SPEAKERS WITH LED
V-1060B
V-1062B, V-1064B, V-1066B
V-1064B Corner Speaker - wood grain with
light brown open weave grille –
10.5”H x 9.75”W x 6.3”D
INTRODUCTION
These instructions contain the specifications and
guidelines necessary to install, operate, and maintain
the 45 Ohm Talkback Interior Speaker Assemblies
with LED.
(26.7cmH x 24.1cmW x 16cmD)
3.6 lbs. (1.63 kg)
V-1066B Corridor Speaker - wood grain with
light brown open weave grille -
10.3"H x 10.3"W x 4.2"D
The 45 Ohm Talkback Interior Speaker Assemblies
with LED are for use with the Valcom "handsfree"
talkback page control units and provide both
loudspeaker and talkback functions with LED
indication in the monitor condition. These speakers
are for interior use only.
(26.2cmH x 26.2cmW x 10.7cmD)
5.7 lbs (2.59 kg)
Power Requirements
SPECIFICATIONS
45 mA @ -24 Vdc max (for powering the LED)
Features
•
•
•
•
45 Ohm Impedance
8 Inch Speaker
LED indicator
Easy Hook-up (2 connections using house cable
or station wire)
Environment
Temperature
Humidity
-20 to +55oC
0-95% non-precipitating
SYSTEM DESIGN
Dimensions/Weights
V-1060B 8" Ceiling Speaker w/LED
13" Dia. X 2.5" D
General
The 45 Ohm Talkback Speakers are designed to be
used with the Valcom "handsfree" talkback control
units. In combination with these units, they will
provide both loudspeaker and talkback functions with
LED indication.
(33.02cm Dia. x 6.35cm D)
2.4 lbs. (1.09 kg)
V-1062B Wall Speaker - wood grain with
light brown open weave grille –
10.6” H x 9.7” W x 5.2” D
(26.9cmH x 24.6cmW x 13.2cmD)
5.3 lbs. (2.41 kg)
1
947067
V-1066B: Unscrew mounting bracket and baffle
from speaker assembly. Using appropriate hardware,
mount the bracket to the wall. After making the
required connections, reattach the baffle to the
speaker and the speaker to the mounting bracket.
INSTALLATION
Connections
Two conductor twisted wire is required for the 45
ohm talkback speakers. Standard 22 or 24 gauge
station wire is acceptable. Shielded wire is not
required or recommended. Connections are as
follows:
TECHNICAL ASSISTANCE
When trouble is reported, verify the unit is properly
connected and there are no broken connections
leading to this unit.
•
•
•
•
Speaker out from page control to speaker tip.
Speaker common to speaker ring.
Switched –24 Vdc to –24 Vdc (LED).
Power supply Ground to GND (LED).
Assistance in troubleshooting is available from the
factory. When calling, you should have a volt-ohm
meter and a lineman's test set and be calling from the
job site. Call (540) 427-3900 and ask for Technical
Support, or (540) 427-6000 for Valcom 24-hour
Automated Support or visit our website at
Mounting
V-1060B: Cut an 8.5" dia. hole in ceiling tile. After
connections have been made to the speaker, attach
speaker to ceiling tile using the mounting hardware
provided. NOTE: Where extra speaker support is
needed, a V-9916 or V-9916M Valcom Bridge and
Backbox should be used.
Valcom equipment is not field repairable. Valcom,
Inc. maintains service facilities in Roanoke, VA.
Should repairs be necessary, attach a tag to the unit
clearly stating company name, address, phone
number, contact person, and the nature of the
problem. Send the unit to:
V-1062B: After making the required connections,
fasten a suitable mounting screw (#10 sheet metal
screw or similar) to the wall at the desired location
for mounting of the speaker. Hang the speaker on
the screw using the keyhole on the speaker bracket.
Repair and Return Dept.
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019-5056
V-1064B: After making the required connections to
the speaker, use appropriate hardware such as an 8d
finishing nail and hang the speaker in the corner.
Typical mounting height would be 8 feet.
TROUBLESHOOTING CHART
SYMPTOM
ACTION
Check tip and ring for audio at speaker.
Check tip and ring for audio at control unit.
•
No sound in page mode.
•
•
•
•
•
•
Low sound in page mode.
Check volume controls at page control.
Poor listening in talkback
mode.
Check talkback volume control at page control. Set
control where audio is clearly audible.
•
No LED indication.
•
Check presence and polarity of LED input signal.
3
947067
VALCOM LIMITED WARRANTY
Valcom, Inc. warrants its products to be free from defects in materials and workmanship under conditions of normal use and service
for a period of one year from the date of shipment. The obligation under this warranty shall be limited to the replacement, repair or
refund of any such defective device within the warranty period, provided that:
1.
2.
3.
inspection by Valcom, Inc. indicates the validity of the claim,
the defect is not the result of damage, misuse, or negligence after the original shipment.
the product has not been altered in any way or repaired by others and that factory sealed units are unopened (A service
charge plus parts and labor will be applied to units defaced or physically damaged),
freight charges for the return of products to Valcom are prepaid,
all units ‘out of warranty’ are subject to a service charge. The service charge will cover minor repairs (Major repairs will
be subject to additional charges for parts and labor).
4.
5.
This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Valcom, Inc. be
liable for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection
with the purchase, operation, or use of the product.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the
carrier should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the
F.O.B. point.
Headquarters:
Valcom, Inc.
In Canada
CMX Corporation
1111 Industry Avenue
Roanoke, VA 24013
Phone: (540) 427-3900
FAX: (540) 427-3517
35 Van Kirk Drive #11 and 12
Brampton, Ontario L7A1A5
Phone: (905) 456-1072
FAX: (905) 456-2269
4
947067
|