VIP-800
NETWORKED PAGING ZONE EXTENDER
INTRODUCTION
The VIP-800 enables voice access to a single zone of
one-way paging over an IP-based LAN/WAN. This will
allow page zone extension anywhere on the network.
SPECIFICATIONS
Access Methods
Dimensions/Weight
· 1.88" H x 5.50" W x 4.15" D
(4.78cm H x 13.97cm W x 10.54cm D)
· PABX (VIP-820 connected to a station port)
· VIP-110 Easy PC paging software
· VIP-810 plus POTS phone
· Weight: 0.55 lbs. (0.25 kg)
· 600 Ohm Supervised Page Port
· Any of Valcom’s distributed amplified
one-way paging units (V-2003A, V-2006A,
Nominal Specifications
Input Impedance:
Input Level:
600 Ohms
-10dBm nominal
-21dBm
V-2924A)
Voice Switch Sensitivity:
Music Source Input Impedance: 8 to 600 Ohms
Features
· RJ45 for network connection
· Front panel activity LED
· Network activity LED’s on RJ45
· Provides audio for up to 150 Valcom
one-way amplified speaker assemblies
· Background music input
· Contact closure or VOX operation of input
· Removable screw terminal connectors provided
for both inputs and outputs
Music Input Level:
Output Impedance:
Output Level:
-10dBm nominal
8 Ohms
-10dBm nominal
Nominal Power Requirements
Voltage:
Current:
24VDC
325mA
Environment
Temperature:
Humidity:
0 to +40 Degrees C
0 to 85% non-precipitating
· Page with music output, music mutes
during page
· Output control contact closure provided during
paging output
· May be used with 25 or 70 Volt amplifiers
· 2.5mm jack for DC power (115VAC TO 24VDC
adapter provided)
· NOTE: Even after assigning a static ID address the
unit will not respond to a “Ping” test.
1
947051
CONNECTIONS
PABX Access
Operation
When using the VIP-800 with an electronic key Follow the telephone system manufacturer’s
system C. O. line position or PABX trunk port, a instructions for access to external paging. Make the
VIP-810 must be used to interface the telephone announcement and hang up. The VIP-800
system with the network.
automatically disconnects from page.
When using the VIP-800 with a PABX station port, The VIP-800 voice switching circuit is activated
a VIP-820 must be used to interface the telephone when the person making the page begins to speak.
system with the network.
When the page is completed or the person stops
speaking for more than two seconds, the paging
circuit turns off. Other functions of the unit remain
the same.
Operation
Press line key (electronic key system) or dial trunk
access code (PABX) to connect to the paging
speakers. Make announcement. The VIP-800
Background Music
automatically disconnects from page when you Background music may be connected to the VIP-
hang up.
800 when using either access method. Background
music mutes when a page is made. Background
music is specific to each unit.
Page Port Access
When accessing the VIP-800 from a telephone
system page port, either VOX or switch closure may
be used to activate the unit.
Connect the output of a low level music source to
the screw terminals marked “Music” on the input
terminal strip on the VIP-800. Adjust music volume
control on the music source to the desired level.
Volume Adjustments
The page volume is set by the speakers. Adjust
speakers 1/3 - 1/2 volume initially, test and reset if
necessary for correct page volume.
3
Application Examples
When using the VIP-800 with an electronic key system C. O. line position or PABX trunk port, a VIP-810
must be used to interface the telephone system with the network. When the electronic key system C. O.
line position or PABX trunk port is accessed, the VIP-810 will activate the VIP-800.
Network
VIP-800
VIP-810
PBX
OR
KEY SYSTEM
LAN
OR
WAN
When using the VIP-800 with a PABX station port, a VIP-820 must be used to interface the telephone
system with the network. When the PABX station port is accessed, the VIP-820 will activate the VIP-800.
Network
VIP-800
VIP-820
PBX
OR
KEY SYSTEM
LAN
OR
WAN
In this example, the VIP-810 and VIP-800 are connected to the data network as stand alone paging. This
could be installed where network access is available, but not paging.
Network
VIP-800
VIP-810
LAN
OR
WAN
4
In these examples, two VIP-800’s are connected to the data network to extend a paging zone to a
remote location.
Telephone
V-2003A
Network
VIP-800
LAN
OR
WAN
Building 1
V-2003A
Zone 1 Audio
Network
VIP-800
LAN
OR
WAN
5
In this example, the VIP-810 is connected to the data network jack already installed and now the network
connected telephone can reach into the existing Valcom V-2924A to access all call priority paging. This
configuration could be used at a guard shack where network access is available, but not a telephone.
LAN
OR
WAN
Page Input
PBX
Network
V-2924A
VIP-800
Override Audio
VIP-810
There are many buildings or areas with existing 70 Volt paging speakers and amplifiers installed.
Often times these systems are not operational or do not provide adequate coverage. The VIP-800 is
ideally suited for integration with conventional paging products. They can be used to interconnect
buildings for paging without the need of additional wire runs. Once connected through the LAN or
WAN, the VIP-800 provides line level outputs and auxiliary contact closures that can be interfaced
with conventional amplifiers. The illustration shown below depicts how integration is accomplished.
From a central location, paging can be accomplished either by specific zone or all call mode.
70 VOLT SYSTEM
Zone 1 Audio
V-1095
Network
VIP-800
VIP-8
LAN
OR
WAN
Note: During initial SETUP, the “Sub-NetAddress” and the “Gateway MAC Number (address) of
the Sub-Net Power” must be programmed in the software of each unit locally - on the SubNet on
which the unit resides.
6
TECHNICAL ASSISTANCE
When requesting assistance, you should include all
available information. It is strongly suggested that you
go to the web site and follow the trouble resolution
When trouble is reported, verify power is being supplied
to the unit and there are no broken connections.
Check voltages for proper polarity to the one-way
amplified speakers. Table 1 identifies symptoms of
some possible problems with solutions. If a spare unit is
available, substitute a spare unit for the suspected
defective unit.
Valcom equipment is not field repairable. Valcom, Inc.
maintains service facilities in Roanoke, VA. Should
repairs be necessary, attach a tag to the unit clearly stating
your company name, address, phone number, contact
person and the nature of the problem. Send the unit to:
Valcom, Inc.
Assistance in troubleshooting is available from the factory.
Call (540) 563-2000 and ask for Technical Support, or
call (540) 767-1555 for Valcom 24-hour Faxback System
Repair & Return Dept.
5614 Hollins Road
Roanoke, VA 24019-5056
TABLE 1: TROUBLESHOOT
PROBABLE
SYMPTOM
1. No output to speakers
A. Check for the presence of au
during a page using a test set
information.
B. Check the DC voltage at the ou
A. Using a test set, check for mu
B. Check that speakers are conn
2. No music output
VALCOM LIMITED WARRANTY
Valcom, Inc. warrants its products to be free from defects in materials and workmanship under conditions of normal use and service for a
period of one year from the date of shipment. The obligation under this warranty shall be limited to the replacement, repair or refund of
any such defective device within the warranty period, provided that:
1. inspection by Valcom, Inc. indicates the validity of the claim;
2. the defect is not the result of damage, misuse or negligence after the original shipment;
3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (Aservice charge
plus parts and labor will be applied to units defaced or physically damaged);
4. freight charges for the return of products to Valcom are prepaid;
5. all units ‘out of warranty’are subject to a service charge. The service charge will cover minor repairs (Major repairs will be
subject to additional charges for parts and labor).
This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Valcom, Inc. be liable
for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the
purchase, operation or use of the product.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier
should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.
7
|