WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page a
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 1
Precautions!
Before you read anything else, please observe the following:
Rechargeable Nickel-Metal-Hydride Battery Warning
•
•
This equipment contains a rechargeable Nickel-Metal-Hydride battery.
The rechargeable Nickel-Metal-Hydride battery contained in this equipment may
explode if disposed of in a fire.
•
•
Do not short-circuit the battery.
Do not charge the rechargeable Nickel-Metal-Hydride battery used in this equipment
in any charger other than the one designed to charge this battery as specified in the
owner’s manual. Using another charger may damage the battery or cause the
battery to explode.
Rechargeable Nickel-Metal-Hydride
Batteries Must Be Disposed
of Properly
Ni-MH
Additional Battery Safety Precautions
Caution! To reduce the risk of fire or injury to persons by the battery, read and follow
these instructions:
1.
2.
Use only the Uniden battery pack (BT-446) specified in the owner’s manual.
Do not dispose of the battery pack in a fire. The cell may explode.
Check the Nickel Metal Hydride battery disposal package insert for
disposal instructions.
3.
4.
Do not open or mutilate the battery pack. Released electrolyte is corrosive and
may cause damage to the eyes or skin. It may be toxic if swallowed.
Exercise care in handling the battery in order not to short the battery with
conducting materials such as rings, bracelets, and keys. The battery or conductor
may overheat and cause burns.
5.
6.
Charge the battery pack provided with or identified for use with this product only in
accordance with the instructions and limitations specified in the owner’s manual
provided for this product.
Observe proper polarity orientation between the battery pack and battery charger.
SAVE THESE INSTRUCTIONS!
The FCC Wants You To Know
Changes or modifications to this product not expressly approved by Uniden, or operation
of this product in any way other than as detailed by the owner’s manual, could void your
authority to operate this product.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
1
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 2
Introduction
WHAM is an accessory of the POLARIS™. The Uniden WHAM 900
MHz analog wireless mic is designed to provide you with years of
trouble-free service. Its rugged components and materials are easily
capable of withstanding the harsh marine environment. As it has a JIS7
waterproof housing to protect the electronics.
We are certain that you will enjoy your WHAM. To ensure that you get
the most from its features, please read this operating guide carefully
before using the unit.
Features
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Geographical Call
Standby
Call Wait
Position Send
Group Call
Position Request
Auto Channel Change
High/Low Function
FIPS
WX Alert
MMSI
U.I.C
Directory
DSC Call
Individual
All Ships
Features, specifications and availability of optional accessories are all
subject to change without notice. The color of your WHAM may vary.
Note:
“POLARIS radio is the device that actually transmits and
receives on the VHF Marine frequencies. The WHAM
communicates with the POLARIS radio through a 900MHz link.”
WHAM meets JIS7 requirements.
Be sure to visit our website: www.uniden.com
Uniden® is a registered trademark of Uniden America.
POLARIS™ is a trademark of Uniden America.
2
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 3
Included with your WHAM
WHAM Owner’s Manual
WHAM
Control Unit
(UAZZ01466ZZ)
Drop-in Charger
(WH85)
AC Adapter
(AD-168)
DC Adapter
(WZ1244)
Mounting Hardware Kit
Alkaline
Battery Tray
Battery
(BT-446)
Belt Clip
(GBCT4A2561Z)
Screw
(MSCW4A2560Z)
Wrist Strap
(RECT484647Z)
3
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 4
Controls and Indicators
10
11
12
6
1
7
2
3
4
8
9
13
14
5
1.
SCAN/MEM - Select Scan mode and setup Memory channels.
Press this key to activate the Scan operation. Press and hold this
key for 2 seconds to place a channel into Scan Memory or remove
a channel from Scan Memory.
2.
3.
4.
POWER/VOL - This is to control the wireless mic power and
speaker volume.
L/M - Change the channel number up/down. These buttons are used to
adjust the volume for Hail mode and to move the cursor in Menu mode.
MENU/HAIL - It is used to access the Menu. Press and hold the
key for 2 seconds to activate the Hail feature.
Microphone
DISTRESS - Send a signal of distress in case of emergency.
WX/ALERT - Select Weather Channel and Weather Alert mode.
Press this key to listen to active NOAA Weather Channels.
Press and hold this key for 2 seconds to place the radio into the
Weather Alert mode.
5.
6.
7.
8.
9.
16/9/TRI - Instantly change to Channel 16, Channel 9, and Triple
Watch mode.
H/L/SELECT - Change transmit power HI/LO and make selections in
the menu. Press this key to change the transmit power to either High
or Low.
10. LIGHT/LOCK – Change the LCD backlight HI/MID/LO, and turn the
Key Lock On/Off.
11. PTT (Press – to – talk) Switch - Press to transmit and release to
receive.
12. Belt Clip
13. Battery Compartment Lock
14. Battery Cover
4
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 5
1
2
3
TX HI USA
4
MEM WX ALT
5
88
6
7
1.
TX (Transmit) - Indicates transmitting.
TRI (Triple Watch) - Indicates Triple Watch Mode and Triple
Watch Scan Mode.
2.
3.
HI (High) - Indicates transmit output is 25 Watts.
LO (Low) - Indicates transmit output is 1 Watt.
USA - Indicates US Channel Mode.
CAN - Indicates Canada Channel Mode.
INT - Indicates International Channel Mode.
4.
MEM (Memory) - Indicates Memory Scan Mode status for each
channel selected.
5.
6.
7.
Channel Display - Indicates Channel Number in use.
WX - Indicates Weather Channel Mode has been activated.
ALT - Indicates Weather Alert Mode has been activated.
DSC CALL
SETUP
REV.CH.MEM
EXIT
88
Menu Display
5
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 6
Getting Started
Mounting the Drop-in Charger
1.
Mount the drop-in charger to either a bulk head or dash.
2.
Plug one end of the AC adapter into a wall outlet, or the DC
adapter into a cigarette lighter socket, and the other end into the
drop-in charger.
* Please turn the power Off on the WHAM before charging.
6
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 7
Installation
Installing the Battery Pack
1.
2.
3.
Use a coin or screw driver to loosen the
screw on the cover.
Unlock both sides of the battery
compartment.
Open the cover.
4.
Connect the battery pack (BT-446)
connector observing the correct
polarity (black and red wires) to the
jack inside the battery
compartment. Do not exert any
force on this connection. It could
cause damage to the battery or
handset.
The plastic connector will fit
together only one way. Once you
are certain that you have made a
good connection, then insert the
battery pack into the battery
compartment. Do not pinch the
wires.
5.
Tighten the screw on the cover.
7
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 8
Or
1.
Put the alkaline battery tray inside,
and install the 3 AAA batteries in
the tray.
2.
Replace the cover.
3.
4.
Lock both sides of the battery
compartment.
Tighten the screw on the cover.
Installing the Beltclip
1.
Place the beltclip on the mounting area
on the back of the WHAM, making sure
the hole in the clip lines up with the
notch on the back of the WHAM.
2.
Insert the screw into the corresponding
hole and tighten.
8
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 9
Control Unit Connection and Installation
1.
2.
Connect the Control Unit cable and the Remote Connector.
Choose the best location for the POLARIS and the Control Unit.
• Away from the vessels compass.
• Away from metal objects that might interfere or obstruct the
signal.
3.
Make sure the WHAM icon appears on the POLARIS’ LCD.
Note:
Register the WHAM to the POLARIS (See page 12). Test the
POLARIS and WHAM before mounting the POLARIS and
Control Unit.
9
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 10
Operation
Power On/Off
Press and hold POWER/VOL for 2 seconds
to turn the WHAM On. You can turn the
WHAM Off by pressing and holding
POWER/VOL for 2 seconds again.
* If you are not able to turn the WHAM Off,
press and hold POWER/VOL for more than
15 seconds.
When you turn the unit On, you will hear
UNIDEN
a beep and the following greeting
message appears on the LCD for more
than 2 seconds.
MARINE RADIO
WIRELESS
88
MICROPHONE
Note:
The POLARIS radio must be
turned On in order for the
WHAM to work.
Triple Watch
Triple Watch monitors Channel 16, Channel 9, and the current Marine
Channel or Weather Channel.
To activate Triple Watch, press and hold 16/9/TRI for 2 seconds. TRI
appears on the LCD, indicating Triple Watch mode is in effect. If a signal
is received on either Channel 16 or Channel 9, the radio remains on that
channel until the signal ends.
TRI HI CAN
MEM
88
Press and hold 16/9/TRI for 2 seconds to cancel the Triple Watch mode.
Note:
While in Triple Watch mode, you can change the currently
selected channel using the L/M keys.
A momentary press of the 16/9/TRI button interrupts Triple
Watch mode and remains on channel 16, or on channel 9 if
you press 16/9/TRI once more. To return to the Triple Watch
mode, simply press the button again.
10
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 11
Weather Channels
To select Weather Channels 0-9, press
WX/ALERT. The radio will go to the last
selected Weather Channel. Press L or M
to select a different Weather Channel.
To exit from Weather Channel:
G Press WX/ALERT. The radio returns
to the previous Marine channel.
WX
8
MEM (Entering channel numbers into Memory Scan)
You can enter channels into Memory Scan for instant scanning at any
time. When a channel is selected for Memory Scan, MEMappears on the
LCD display.
To enter a channel into Memory Scan,
select the channel you want to store by
pressing L/M on the WHAM, and then
press and hold SCAN/MEM for 2 seconds.
The channel is stored in Memory Scan and
MEMappears on the LCD display.
HI CAN
MEM
88
Volume Adjusting
1.
When you press POWER/VOL, the
volume indicator appears on the
display.
Press L to turn the volume up,
press M to turn the volume down.
TRI LO CAN
VOL ¡¡¡
88
2.
3.
When you finish adjusting the volume, press the POWER/VOL to
exit from the volume-adjusting mode.
11
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 12
Registering the WHAM to the POLARIS
Note:
When you use the WHAM in addition to the POLARIS wired
mic, please set the BASE ID for the POLARIS the same as the
WHAM. (Please refer to the Owners Manual for the POLARIS).
1.
When the WHAM is turned On for
Base ID->_
the first time, the following screen
Hand set ID->
appears.
2.
Press L to increase the number, or
press M to decrease the number.
The number will be entered when
the H/L/SELECT is pressed, and the blinking digit moves to the
right. (You can select any number between 0000 and 9999.)
3.
4.
After the Base ID is entered, the Handset ID blinks.
You can select the Hand set IDby pressing L or M, and then
press H/L/SELECT to enter the number.
5.
Turn the WHAM Off to confirm the data.
Note:
When the following screen
appears, the transceiver may not
Now
have the correct Base ID or the
WHAM is too far from the
Linking
POLARIS. Confirm whether the
Base ID is right. If the screen
does not change, move closer to the POLARIS. In order to
register the WHAM to the POLARIS, you have to turn the
POLARIS Off once. In case you need to rewrite the ID, you
need to press and hold MENU/HAIL and turn the WHAM On.
When you rewrite the ID, press and hold MENU/HAIL for
2 seconds and turn the WHAM On to change the Base ID and
Handset ID.
* Please refer to the POLARIS’ Owners Manual for menu
operation. The key names may vary.
12
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 13
Hail
To access the Hail mode, press and hold
MENU/HAIL for more than 2 seconds on
HAIL VOL
¡¡¡
the WHAM. The HA icon appears on the
display. Press the PTT switch on the
microphone, hold the microphone
HA
approximately two inches away from your mouth, and speak clearly in a
normal voice. To cancel Hail mode, press and hold MENU/HAIL for
more than 2 seconds on the WHAM.
Hail Volume adjust
While the POLARIS is in the Hail mode, you
can adjust the out going volume by pressing
the L/M keys on the WHAM.
Low Battery Alert
When the battery pack (or batteries) are
very low and need to be charged (or
changed), the following screen appears.
Battery Low
Complete the conversation as quickly as
possible and return the handset to the
charger unit for charging (or replace the
batteries).
Backlight Adjust
You can adjust the backlight in 3 stages by pressing LIGHT/LOCK
continuously (LO→MID→HI). When you push any key (except PTT),
the backlight turns On for 5 seconds.
Key Lock On/Off
You can turn the Key Lock On by pressing and holding LIGHT/LOCK
when the Key Lock is Off. When it is set to On, "--" appears.
If you want to turn the Key Lock Off, you can press and hold
LIGHT/LOCK for 2 seconds.
TRI HI CAN
Note:
Key Lock is invalid while the WX
ALERT is sounding or WX
ALERT CH is receiving.
MEM
13
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 14
Distress
Note:
You must set the user MMSI in order to send a Distress call.
Please see the POLARIS Owner’s Manual on page 40 to set
the MMSI.
This feature will allow you to transmit a Distress call.
1.
In order to transmit a Distress call,
press and hold DISTRESS for
5 seconds. Then, the following
screen appears and select SEND
or CANCEL. If you select
DISTRESS
SEND
70
CANCEL
CANCEL, the display returns to
the channel display screen.
2.
3.
Press H/L/SELECT to send.
The Distress call is transmitted
and it waits for about 210 - 270
seconds. This is continued
internally . The transceiver alert
will be sounding, and it also
"shadow-watches" for a
DISTRESS ACK
WAITING
CANCEL
transmission between CH16 and
CH70 until an acknowledgment
signal is received from the Coast
Guard shore station.
4.
5.
To cancel the Distress call, press
H/L/SELECT.
When the WHAM receives a
Distress call, the following screen
appears. If an acknowledgment is
not received, the Distress call is
repeated until an acknowledgment
is received from the Coast Guard
shore station.
DISTRESS
06/15 10:30A
JUNE BRAWLEY
FIRE
70
Note:
If the POLARIS receives a Distress call, it will also be
displayed on the WHAM LCD display. An emergency alert will
sound. The name will be displayed if it is the name registered
in the directory. Otherwise, sender’s MMSI is displayed.
Latitude, longitude, and time information will also be displayed
only on the POLARIS, if the GPS module is carried in the
vessel that transmitted a DSC Distress call.
14
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 15
Troubleshooting
If the WHAM does not perform to your expectations, try the suggestions
listed below, If you cannot get satisfactory results, call Uniden Technical
Support at (800) 586-0409, 8:00 a.m. to 5:00 p.m., Central Standard
Time, Monday through Friday.
CAUSE
REMEDY
SYMPTOM
No or low voltage.
Check for proper voltage.
Recharge or replace the
batteries.
Won’t power On.
Bad mic element.
Send in for repair.
When the PTT is
pressed - TX icon
comes on and
another radio can
hear a “click” but no
audio is heard.
A source of noise
is nearby.
Eliminate the source of
the noise or delete the
channel from the
While scanning, the
radio stops on a
particular channel all
of the time.
Scan Memory.
An external noise is Either turn off the
being generated by offending device or
There is noise on
the receiver that the
squelch will not
eliminate.
some device.
contact that Mfg.
Regarding FCC part 15
“unintentional radiator”.
POLARIS is
turned Off.
Turn the POLARIS On.
WHAM won’t control
the POLARIS.
Care and Maintenance
Your WHAM is a precision piece of electronic equipment and you should
treat it accordingly. Due to the rugged design, very little
maintenance is required. However, a few precautions should be
observed:
• You are responsible for continued FCC technical compliance of
your radio.
• You are urged to arrange for periodic performance checks with
your Uniden Marine dealer.
15
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 16
Specification
General
Standard Voltage
:
Portable Unit 3.6 V DC 0.1 V
Base Unit 13.8 V DC 0.1 V
Operating Temperature
Channel
Standard Deviation
Buttons
:
:
:
:
:
–10 °C to + 50 °C
20 (from 902.244203 MHz to 927.698745 MHz)
1 kHz 40 kHz Dev.
POWER, SCAN, WX, 16/9, MENU, H/L, L/M
H 117.1 mm x W 63.1 mm x L 34.5 mm
H 4.61 inches x W 2.48 inches x L 1.36 inches
200 g / 0.44 lbs / 7.05 oz (include batteries)
Meets JIS 7 requirements
Size
Weight
Water Protect Class
:
:
Receiver
UNIT
NOMINAL LIMIT
Sensitivity 12 dB SINAD (at 40 kHz Dev.)
with CCITT Filter
dBm
–106
< –100
Frequency Response (Ref: 1kHz) 0.3 kHz
3.0 kHz
dB
dB
W
%
dB
–43
–5
0.17
1.0
70
< –30
–10 to –3
0.15 <
< 5
Audio Output Level (8 ohms)
Distortion at 1 mV RF Input
Vol Max
Vol Lv:5
Hum & Noise Ratio at 1 mV RF Input
with CCITT Filter Vol Lv:5
50 <
Selectivity
6 dB Bandwidth + kHz
80
80
50 <
50 <
(NQ20dB at DISCRI point) 6 dB Bandwidth – kHz
Image Rejection Ratio
SINAD 12 dB with CCITT Filter
1st Image (f0 - 21, 0795428 MHz)
dB
35
25 <
Transmitter
UNIT
NOMINAL LIMIT
RF Power (50 Ω Load)
Modulation Sensitivity
Frequency Response (Ref: 1kHz) 0.3 kHz
3.0 kHz
dBm
mV
dB
–4.2
13
–15
4
–7.0 to –2.0
<16
< –10
0 to 8
dB
Frequency Tolerance (25°C)
Distortion
Hum & Noise Ratio with CCITT Filter
Hi Speed Data Deviation
Lo Speed Data Deviation
Hz
%
dB
KHz
KHz
0
–2500 to +2500
< 5
30 <
35 to 55
10 to 20
1.5
38
45
15
Trickle Charger
Charge Time
: 15 hour (Typical)
Other
Battery
: Ni-MH Battery 800 mAH BT-446
3 AAA Alkaline Batteries
Battery Life (TX:5%, RX:5%, Stand-by:90%) : 10 hour (Typical) BT-446
16
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page 17
Warranty
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for three years, to the original
retail owner, this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and
be of no further effect 36 months after the date of original retail sale. The
warranty is invalid if the Product is (A) damaged or not maintained as
reasonable or necessary, (B) modified, altered, or used as part of any
conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any
system not manufactured by Uniden, or (F) installed or programmed by anyone
other than as detailed by the Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to
this warranty at any time while this warranty is in effect, warrantor will repair the
defect and return it to you without charge for parts, service, or any other cost
(except shipping and handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. THE LIMITED WARRANTY
SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING
TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER
WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT
COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this
exclusion or limitation of incidental or consequential damages so the above
limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state. This warranty is void
outside the United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in this Operating Guide you are certain that the Product
is defective, pack the Product carefully (preferably in its original packaging).
Include evidence of original purchase and a note describing the defect that has
caused you to return it. The Product should be shipped freight prepaid, by
traceable means, or delivered, to warrantor at:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd.
Ft. Worth, TX 76155
(800) 235-3874, 8 AM to 5 PM Central,
Monday through Friday
17
WHAM_UA466ZL UA01466ZA_0 9/20/02 12:50 PM Page b
|