Install the AA Batteries
Charge the AA batteries for at least 17-20 hours before
completing the installation or using the handset.
Press down on the battery cover
release and slide the cover down
until it comes off.
1
Install the batteries supplied
with your phone. Check for
correct (+ -) polarity.
2
Securely close the battery
compartment cover by sliding
it until it snaps into place.
3
“Please Register” appears in
the display.
Place the handset in the charging
cradle with the keypad facing forward.
4
The DCX520 will only work with
“AA” Ni-MH rechargeable batteries.
If you use any other type of
batteries, the display will show “Use
rechargeable battery only”.
• Use only “AA” rechargeable Ni-MH
batteries. Do Not use Alkaline, Lithium,
or non-rechargeable batteries. To insure
maximum performance and safety, use
replacement batteries specifically matched for
Using incorrect batteries could damage or
limit the performance of the handset and
could cause bodily injury.
• Recharge your handset on a regular basis by
returning the handset to the charger after
each phone call.
– 3 –
Battery Information
Battery use time (per charge)
From fully charged (17-20 hours charge time)
• Up to 7 hours continuous use
(up to 5 hours when the Clarity Booster is On)
• Up to 14 days when the handset is in the standby mode
(up to 24 hours in the DirectLink mode)
Low battery alert
When the batteries are very low and need to be charged, the phone
is programmed to eliminate functions in order to save power.
The batteries need to be charged when:
- The battery icon
appears.
- “Low Battery” appears in the display.
If the phone is in the standby mode, none of the keys will operate.
If you are on a call, complete your conversation as quickly as
possible, and return the handset to the charging cradle.
Cleaning the battery charging contacts
To maintain a good charge, it is important to clean the charging
contacts on both the handset and the
charger once a month. Use a dry cloth
or pencil eraser to clean. If the contacts
become very dirty, use water only, dampen
a cloth to clean the charging contacts.
Then make sure to go back over the charging
contacts with a dry cloth before returning
the handset to the charger to charge.
contacts
Connect the Charger
Connect the AC adapter
1
to the DC IN 9V jack
and to a standard 120V
AC wall outlet.
Set the charger on a
2
desk or tabletop, and
place the handset in
the charger with the
keypad facing forward.
– 4 –
Make sure the charge LED illuminates. If the LED does not
illuminate, check to see that the AC adapter is plugged in
and that the handset makes good contact with the charger
charging contacts.
3
• Use only the supplied AD-310
AC adapter. Do not use any
Polarity of the plug
other AC adapter.
• Place the charger close to the AC
outlet so that you can unplug the
AC adapter easily.
Register the Handset
YOU NEED TO REGISTER THE DCX520 BEFORE USE.
After placing the batteries in the handset and charging the
batteries, remove the handset from the charger and place it
in the main base.
1
Registration starts automatically. While registering,
“Handset Registering” appears in the display.
2
When the registration is complete,
“Registration Complete” appears in the display.
3
If the registration fails, “Registration Failed” appears in
the display. Try the steps above again.
• An extra handset can be registered when the main base
is in the standby mode.
• In some cases you may need to attempt registration a
few times.
Using the DCX520 with the
Integrated Answering Device
If the original unit has a built-in answering system, you can check
your new messages, skip, repeat, or delete your messages with the
DCX520 handset. For more instructions, see the owner’s manual
supplied with the original unit.
– 5 –
To playback a message
To skip a message
Press the
Press the
soft key.
soft key.
To repeat the current message Press the
To repeat the previous message Press the
soft key after four seconds.
soft key within four seconds.
To delete a message
To stop operation
Press the DELETE soft key.
Press end.
• If you press end before the answering system answers, the
phone will return to the standby mode.
• When the answering system does not answer within 6 seconds,
you will hear a beep and the phone will return to the
standby mode.
• When you receive a call, the remote operation is canceled.
I.C. Notice
TERMINAL EQUIPMENT
NOTICE: This equipment meets the applicable Industry Canada
Terminal Equipment Technical Specifications. This is confirmed by
the registration number. The abbreviation, IC, before the
registration number signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry
Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal
equipment is marked on the equipment itself. The REN assigned to
each terminal equipment provides an indication of the maximum
number of terminals allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed five.
RADIO EQUIPMENT
The term “IC:” before the radio certification number only signifies
that Industry Canada technical specifications were met.
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device. “Privacy of communications may not be
ensured when using this telephone”.
– 6 –
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this
Uniden Product to be free from defects in materials and craftsmanship with only the
limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further
effect 12 months after the date of original retail sale. The warranty is invalid if the Product
is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used
as part of any conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an authorized
Uniden service center for a defect or malfunction covered by this warranty, (E) used in any
conjunction with equipment or parts or as part of any system not manufactured by Uniden,
or (F) installed or programmed by anyone other than as detailed by the owner’s manual for
this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at
any time while this warranty is in effect, warrantor will either repair or replace the defective
unit and return it to you without charge for parts, service, or any other cost (except
shipping and handling) incurred by warrantor or its representatives in connection with the
performance of this warranty. Warrantor may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING
TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESSED, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do
not allow this exclusion or limitation of incidental or consequential damages so the above
limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. This warranty is void outside the United States
of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions
in the owner’s manual you are certain that the Product is defective, pack the Product
carefully (preferably in its original packaging). The Product should include all parts and
accessories originally packaged with the Product. Include evidence of original purchase and a
note describing the defect that has caused you to return it. The Product should be shipped
freight prepaid, by traceable means, to warrantor at:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023, 8 a.m. to 5 p.m. Central, Monday through Friday
– 7 –
|