D1384 Series User's Guide
What's in the box?
You will also find:
Accessory handset
and charger
D1384 base with
Not pictured:
x Rechargeable
battery (BT-1021)
answering system
and cordless
handset
x Battery cover
x AC adapter
(PS-0035)
You should
have:
None
If you purchased
model number:
D1384
Not pictured:
x Rechargeable battery (BT-1021)
x Battery cover
x AC adapter (PS-0035)
x Telephone cord
D1384-2
D1384-3
D1384-4
D1384-5
D1384-6
1 of each
2 of each
3 of each
4 of each
5 of each
x If any items are missing or damaged, contact our Customer Care Line
immediately. Never use damaged products!
x Call waiting, CID, CIDCW, and Voice Mail are telephone line services. Contact your
provider for details.
If You...
Contact Uniden’s...
Customer Care Line*
Parts Department*
Accessibility Help Line
Phone Number
817-858-2929 or
800-297-1023
800-554-3988
800-874-9314
(voice or TTY)
have a question or problem
need a part or an accessory
need special assistance due to
a disability
* During regular business hours, Central Standard Time; see our website for detailed
business hours.
© 2011 Uniden America Corp.
Ft. Worth, Texas
Printed in Vietnam
U01UN331ZZZ(0)
GETTING STARTED
Installing Your Phone
Charge the Baꢂery
1. Unpack all handsets, battery packs, and battery
covers. If you need to remove a cover, press in on the
notch and slide the cover down and off.
2. Line up the battery connector with the jack inside the
handset; the connector only fits one way.
3. Push the connector in until it clicks into place; tug gently on the wires to
make sure the battery is securely connected.
4. Replace the battery cover and slide it into place.
5. Use an AC adapter to connect the power jack on the base to a regular indoor
(120V AC) power outlet. Connect any chargers the same way.
6. Place a handset in the base with the display facing forward. If the display
doesn’t light up, reseat the handset or connect the base to a different outlet.
For 2 or more handsets, place each handset in a charger.
# Charge the handset completely (about 15 hours) before using.
Connect the Telephone Cord
1. Use the telephone cord to connect the TEL LINE jack on the base to a standard
telephone wall jack.
# If the display says Check Tel Line, check the connection between the
base and the phone jack.
2. If you are mounting the phone on the wall, place the mounting slots (on the
rear of the base) over the pins on the wall plate; slide the base down to lock
it into place.
Test the Connecꢀon
Make a quick test call. Pick up the handset and press TaLk/fLash. (Press ENd to
hang up.)
x If there’s a lot of noise, check for interference (see p. 13).
x If you keep hearing a dial tone, change to pulse dialing (see below).
Changing from Tone to Pulse Dialing
Your phone uses tone dialing by default. If your phone company uses pulse
dialing, you need to change your phone’s dial mode.
1. Press MENu/sELEcT and select Global Setup.
2. Select Dial Mode then Pulse. You’ll hear a confirmation tone.
To send DTMF tones during a call (e.g., for an automated response system),
press to temporarily switch to tone dialing. When you hang up, the phone
*
automatically returns to pulse dialing.
English - 3
Geꢁng to Know Your Phone
Earpiece
Status
Indicator
Display
UP
FIND HANDSET
MENU/SELECT
SPEAKER
CALLER ID/RIGHT
Display
PHONEBOOK/
LEFT
END
TALK/
FLASH
DOWN
Charging
Contacts
Twelve-
key dial
pad
Base
REDIAL/
PAUSE
MESSAGE/
MUTE
Microphone
Key
fINd
What it does
x In standby: page all handsets.
INTERCOM/
CLEAR
Charging
contacts
Handset
Key (icon)
What it does
x In standby: increase the ringer volume.
x During a call: increase the volume.
up (
)
x In any menu or list: move the cursor up one line.
x Switch a normal call to the speakerphone (and back).
spEakER (
)
x In standby or during a call: open the phonebook.
x In the menu: go back to the previous screen.
phoNEbook/
LEfT (
)
x In standby: start a telephone call (get a dial tone).
x During a call: switch to a waiting call.
TaLk/fLash
x In standby: open the redial list.
x While entering a phone number: insert a 2-second pause.
REdIaL/pausE
x In standby: start an intercom call.
x During a call: put the call on hold and start a call transfer.
x In standby: open the menu.
x In any menu or list: select the highlighted item.
INTERcoM/cLEaR
MENu/sELEcT
caLLER Id/RIGhT x In standby or during a call: open the CID list.
x During a call: hang up.
x In any menu or list: exit and go to standby.
ENd
4 - English
Key (icon)
What it does
x In standby: decrease the ringer volume.
x During a call: decrease the volume.
dowN (
)
x In any menu or list: move the cursor down one line.
x In standby: access your answering system.
x During a call: mute the microphone.
x While the phone is ringing: ignore this call (mute the ringer).
MEssaGE/MuTE
(
)
LED
What it means
x On: the battery is charging.
x Blinking: there are new messages.
sTaTus
INdIcaToR
Reading the Display
The icons appear based on what you're doing with the phone.
Icon
What it means
Icon
What it means
The battery is 1) fully charged,
2) half charged, 3) getting low,
or 4) empty.
You have a voice mail
message.
You have an answering system
message.
The speakerphone is on.
Privacy Mode is on (see p. 10).
The ringer is turned off.
T-coil mode is on (see p. 6).
[Aa] Enter 1) capital or 2) lower
[aA] case letters.
Entering Text on Your Phone
x Use the 12-key dial pad anytime you want to enter text into your phone (e.g. a
name in the phonebook).
x If two letters in a row use the same key, enter the first letter; wait for the
cursor to move to the next space and enter the second letter.
To...
Press...
move the cursor left
move the cursor right
erase the character at the cursor
erase the entire entry
enter a blank space
phoNEbook/LEfT.
caLLER Id/RIGhT.
INTERcoM/cLEaR.
and hold INTERcoM/cLEaR.
#
.
switch between upper and lower case letters
.
*
English - 5
To...
Press...
rotate through the punctuation and symbols
0.
Using the Menu
To open the
menu, press
x If you don't press any keys
for about thirty seconds, the
handset exits the menu.
x During a call, use phoNEbook/
LEfT to back out of the menu
without hanging up.
Press MENU/SELECT
to choose the
MENU/SELECT.
highlighted option
.
The cursor
shows the
highlighted
option.
Handset Setup
Handset Setup
T-coil
Answering Setup
Use UP & DOWN
to rotate
through the
options.
press END
to exit the
To go back a
screen, press
PHONEBOOK/LEFT
OR
menu
.
Handset Setup Menu
Menu Option
What it does
Reduce noise on hearing aids equipped with a telecoil
(T-coil) feature. It shortens talk time, so keep your battery
fully charged.
T-coil
Choose the handset's ring tone. As you highlight each ring
Ringer Tones
AutoTalk
tone, you hear a sample. To confirm, press MENu/sELEcT.
Have this handset answer a call when you pick it up from
the cradle (without pressing any buttons).
Have this handset answer a call when you press any key on
the 12-key dialpad.
Change the name used on the handset’s display.
Any Key Answer
Banner
Handset Language Change the display language.
Key Touch Tone
Have the keypad sound a tone when you press a key.
Answering Setup Menu
Refer to p. 10 for details on setting up your answering system.
Date & Time Menu
Use this menu to set the clock (if you have Caller ID, the phone sets date and time
automatically). Enter the date and time; select AM or PM. Use caLLER Id/RIGhT to
move the cursor past a digit without changing it. To confirm, press MENu/sELEcT.
Global Setup Menu
The settings on this menu affect all handsets.
6 - English
Menu Option
Dial Mode
Set Line Mode
VMWI Reset
What it does
Choose tone or pulse dialing (see p. 3).
Do not change it unless instructed to by customer service.
Reset the Visual Message Waiting Indicator (see p. 10).
USING YOUR PHONE
Basics
To...
Using the earpiece
Using the speakerphone
press spEakER.
make a call, dial the number, and press TaLk/fLash.
answer a call
press TaLk/fLash.
press spEakER.
hang up
press ENd or put the handset in the cradle.
ignore a call/mute the ringer
press MEssaGE/MuTE while the phone is ringing.
switch to the speaker and back press spEakER.
mute the microphone during
a call
Press MEssaGE/MuTE.
Press again to turn the microphone back on.
put a call on hold
press INTERcoM/cLEaR*.
return to a call on hold
press TaLk/fLash.
press spEakER.
* Aſter 5 minutes on hold, the call will be disconnected.
Changing the Volume
You can adjust the volume of the earpiece, speaker, and ringer separately.
To change the...
earpiece volume
speaker volume
When...
Press...
up to increase the
volume.
dowN to decrease
it.
you are listening to that earpiece or
speaker (playing messages, etc.)
ringer volume *
the phone is in standby
* To turn off the ringer, turn the ringer volume all the way down.
Finding the Handset
With the phone in standby, press fINd on the base. Each handset will beep for 1
minute. To cancel, press fINd again or press any handset key.
Using the Phonebook, Caller ID, and Redial Lists
x The phone can store up to 30 entries in its phonebook.
x If you subscribe to Caller ID (CID) service, the phone stores the information for
the last 30 received calls to the CID list. Contact your telephone provider for
more information.
English - 7
x Each handset remembers the last 5 numbers you dialed on it.
x Only one handset can access one of the lists at a time.
To...
Press...
phoNEbook/LEfT, caLLER Id/RIGhT, or
REdIaL/pausE.
open the list
scroll through the list
up or dowN.
dial the current entry
TaLk/fLash or spEakER.
add 1 at the front of CID number
before dialing for a toll call.
*
store the current CID or redial entry MENu/sELEcT, then select Store Into Pb.
to the phonebook
Proceed to edit the name and number.
edit the current phonebook entry
MENu/sELEcT, then select Edit.
MENu/sELEcT, then select Delete (or
delete the current entry
close the list
Delete Entry). To confirm, select Yes.
phoNEbook/LEfT.
# When it’s in standby, the handset shows how many calls came in
since the last time you checked the CID list.
Adding Phonebook Entries
With the phone in standby, open the phonebook. Press MENu/sELEcT and then
select Create New. Proceed to enter a name and number.
x Enter the phone number (up to 20 digits) exactly as you would dial it.
x If you need to enter a pause between the numbers, press REdIaL/pausE; you’ll
see a P in the display. (The dialing will pause for about 2 seconds per a digit.)
x To edit the number, press INTERcoM/cLEaR to back up the cursor and delete
numbers. Re-enter the correct numbers.
Deleꢀng All the Entries
With the phone in standby, open the list (phonebook, CID, or redial). Press MENu/
sELEcT and then select Delete All. To confirm, select Yes.
Chain Dialing
If you often have to enter a series of digits or a code number during a call, you
can save that code number as a regular phonebook entry and use the phonebook
to send the code number.
Make a call normally. When you hear the prompt that asks you to enter your
number, open the phonebook and find the entry. Press MENu/sELEcT to send the
code. If you change your mind, just close the phonebook.
8 - English
Using Call Waiꢀng
x Call Waiting, a service available from your telephone provider, lets you receive
calls while you are on another call. Caller ID on Call Waiting (CIDCW) service
displays CID information for a waiting call.
x If you get a Call Waiting call, the phone sounds a tone. Press TaLk/fLash to
switch between the current call and the waiting call; each time you switch,
there is a short pause before you’re connected to the other caller.
Mulꢀ-Handset Features
# To use the features in this section, you need at least 2 handsets.
Handset to Handset Intercom
x You can make an intercom call from any handset, but only two handsets can be
in an intercom call at any time.
x If an outside call comes in during an intercom page, the phone cancels the page
so you can answer the incoming call.
x If an outside call comes in during an intercom call, press TaLk/fLash to hang up
the intercom call and answer the outside call.
To page another handset
To answer the page
1. With the phone in standby, press INTERcoM/cLEaR.
Press TaLk/fLash or
INTERcoM/cLEaR.
2. Select the handset you want to page, or select All.
(To cancel, press ENd.)
To end an intercom call, press ENd. Both handsets return to standby.
Call Transfer
To page another handset
To answer the page
1. During a call, press INTERcoM/cLEaR. The phone
1. Press INTERcoM/
cLEaR . Speak to
puts the call on hold.
the other handset.
2. Select the handset you want to page, or select All.
(To cancel and return to the call, press TaLk/fLash.)
2. Press TaLk/fLash
to speak to the
caller.
3. When the other handset accepts the call, you’ll be
disconnected (press TaLk/fLash to rejoin the call).
Conference Calling
x When an outside call comes in, two handsets can join in a conference call with
the outside caller.
x To join a call that’s already in progress, just press TaLk/fLash or spEakER.
x To leave the conference call, hang up normally; the other handset remains
connected to the call.
English - 9
Privacy Mode
To activate privacy mode on a call in progress, press MENu/sELEcT twice. As long
as privacy mode is on, you’ll see a in the display, and no other handsets can
join your call. Privacy mode turns off automatically when you hang up; you can
also turn it off by pressing MENu/sELEcT twice.
Using a Voice Mail Service
x If you subscribe to a voice mail service, your phone can notify you when
you have a new message waiting. This feature supports Frequency-Shift
Keying (FSK) message notification. Contact your voice mail provider for more
information.
x When you have new messages, the sTaTus LED on the handset blinks, and the
display shows a message icon.
x After you listen to your messages, the voice message icon turns off. If it
doesn’t, you can reset it. With the phone in standby, open the menu and select
Global Setup; select VMWI Reset, then select Yes.
USING THE ANSWERING SYSTEM
Answering System Opꢀons (Answering Setup
)
You can set or change the answering system options from any handset. Just open
the menu and select Answering Setup. Select one of the following:
Menu Option
What it does
Enter a 2-digit PIN so you can access your answering system
from any touch-tone phone (see p. 12).
Security Code
Set the number of rings (2, 4, or 6) before the system
answers (see p. 12 about Toll Saver).
Ring Time
Set the amount of time (1 or 4 minutes) callers can leave
a message. Choose Announce Only if you don't want the
system to let callers to leave a message.
Record Time
Ans. Language
Ans. On/Off
Change the language of the system's voice prompts.
Turn your answering system on or off.
Record Greeting Record an outgoing message or greeting (see below).
Greeting Options Switch greetings or delete your greeting (see below).
Personalizing the Greeꢀng
Your personal outgoing message or greeting can be from 2 to 30 seconds long. If
you don’t record a greeting, the system uses a pre-recorded greeting: Hello, no
one is available to take your call. Please leave a message after the tone.
10 - English
With the phone in standby, open the menu. Select Answering Setup and select
an action from the following table:
To...
Follow these steps:
1. Select Record Greeting. and press MENu/sELEcT.
2. Wait until the system says "Record greeting", then you
can start recording. Press MENu/sELEcT to stop recording.
3. The system plays back your new greeting. To keep
the greeting, press ENd. To re-record it, wait until the
playback ends and then press MENu/sELEcT.
Record a
personal
greeting
Switch between Select Greeting Options. The system plays back the current
greetings
greeting. Press MENu/sELEcT to switch greetings.
Delete your
greeting
Switch to your personal greeting, then press INTERcoM/cLEaR.
Accessing the Answering System
When the phone is in standby, you can access the system from any handset:
x Only 1 handset can access the
Press MESSAGE/MUTE to start
system at a time.
remote operation mode.
x During remote access:
- The handset display shows the
number of messages.
- The system beeps so you know it's
waiting for your next command.
Use CALLER ID/
Use PHONEBOOK/
LEFT to go to the
previous option:
RIGHT to go to
the next option:
5:Stop
[
/
/select]
4:Delete
3:Skip
1:Repeat
2:Play
2:Play
3:Skip
- You can press the number key
shown next to each command
instead of scrolling through the
screens.
1:Repeat
4:Delete
Press MENU/
Press END to
exit remote
operation mode.
SELECT to choose
the displayed option.
- If you do nothing for 30 seconds, the phone returns to standby.
Geꢁng Your Message
When you have new messages (that you have not listened to yet), only the
new messages will be played. To play old messages, complete to play all new
messages first, then start message playback again.
To...
Follow these steps:
play new messages Press MEssaGE/MuTE.
Wait at least 5 seconds after starting this message,
select 1:Repeat.
restart this message
replay an earlier
message
Within 2 seconds after starting a message,
select 1:Repeat.
English - 11
To...
Follow these steps:
skip a message
Select 3:Skip.
delete this message Select 4:Delete.
play old messages
stop playback
After the system plays all new messages, select 2:Play.
Select 5:Stop.
Screening Your Calls
While the system takes a message, you can listen from a handset. Only one
handset can screen calls at a time. If another handset tries to screen calls, it
beeps and returns to standby.
To...
Press...
hear the caller leaving a message
answer the call
MEssaGE/MuTE.
TaLk/fLash.
mute the call screen without
answering*
ENd or return the handset to the cradle.
* If you mute the call screen, the system conꢁnues taking the message: it just stops
playing through the speaker.
Using the System While You’re Away from Home
You can dial in to your answering system from any touch-tone phone. Before you
can use this feature, you must program a security code.
Programming a Security Code
With the phone in standby, open the menu; select Answering Setup, then select
Security Code. Use the number keypad to enter a two-digit security code (01 to
99). Press MENu/sELEcT when you’re finished.
# Remember to make a note of your new security code!
Dialing In to Your System
1. Call your phone number from any touch-tone phone, and wait until the
system answers.
x If you have the Ring Time set to Toll Saver, the system answers after 2 rings
if you have new messages and 4 rings if you don’t. You can hang up during
the third ring.
x If the system is turned off, it answers after 10 rings and beeps sound.
2. During the greeting or beeps, press
0
and immediately enter your security
code. If you enter it incorrectly 3 times, the system hangs up and returns to
standby.
12 - English
3. The system announces the time, the number of messages in memory, and a
help prompt. It beeps to let you know it’s waiting for a command; enter a
2-digit command
01 Repeat message
02 Play message
03 Skip message
04 Delete message
05 Stop playback
from the chart.
# If you don’t press
any keys for 15
seconds, the
06 Turn the system on
09 Turn the system off
10 Hear help prompts
system hangs
up and return to
standby.
IMPORTANT INFORMATION
Troubleshooꢀng
General problems
Possible solutions
x Check the telephone cord connection.
I can’t make or receive x Disconnect the base AC adapter. Wait a few
calls.
minutes, then reconnect it.
x Make sure the base is plugged in.
The handset won’t ring. x Make sure the ringer is turned on.
x Charge the battery for 15-20 hours.
x Check the battery connection.
The handset is not
working.
x Let calls ring twice before answering.
x Make sure your CID service is active.
The handset won’t
display CID information.
Audio issues
Possible solutions
x The battery is getting low. Check the handset for a low
battery alert. Finish your conversation and return the
handset to the cradle as soon as possible.
I hear a beeping
during a call.
x Check for interference from appliances (microwave
ovens, TVs, etc.) or wireless devices (baby monitors, WiFi
equipment, etc.). Move the handset or base away from the
interference source.
There’s a lot of
noise or static
on the line
x Move the handset closer to the base.
x If you use a telecoil hearing aid, turn the T-coil on (see p. 6).
Multi-handset problems
Possible solutions
x You may have to reset the handset.
Contact Customer Service for instructions.
I can’t transfer calls.
Two handsets can’t talk to a caller. x See if any handset is in Privacy Mode.
English - 13
Multi-handset problems
A handset says Unavailable.
Answering system problems
Possible solutions
x Move the handset closer to the base.
x See if any handset is in Privacy Mode.
Possible solutions
x Make sure the answering system is on.
x Make sure the base is plugged in.
The answering system does not
work.
x See if Record Time is set to Announce Only.
x Delete messages (memory may be full).
The system won't record
messages.
x See if another handset is using the system.
x Make sure the phone is in standby.
A handset can't access the
answering system.
x If there was a power failure, re-record your
personal outgoing message.
My outgoing message is gone.
x Increase the Record Time.
Messages are incomplete.
The system keeps recording
x Delete messages (memory may be full).
x You may have to change the line mode.
when I answer on an extension. Contact Customer Service for instructions.
Installing a Line Filter or DSL Filter
x A telephone line filter or DSL filter prevents services that use the phone line
from causing interference on your phone. To get a line filter, contact your
service provider or look in an electronics store.
x Plug the filter into the telephone wall jack and plug the base into the filter.
Make a test call to make sure the noise is gone.
Liquid Damage
CAUTION: If the base is covered in liquid, disconnect the adapter and
phone cord from the wall before touching it.
If the liquid is only on the exterior housing of the base or handset, wipe it off and
use as normal. If you can hear liquid inside the housing:
1. Remove all compartment covers, and disconnect all cables and cords.
2. If liquid is leaking from any vent or hole, turn the phone so that vent faces
down. If not, place the largest vent face down.
3. Let dry for at least 3 days. Check for liquid inside the phone before replacing
compartment covers and reconnecting cords.
14 - English
x
As part of our commitment to protecꢁng our
environment and
Adapter and Baꢂery Informaꢀon
AC adapter Base Charger
Part number PS-0035 PS-0035
Input voltage 120V AC, 60 Hz
conserving natural
resources, Uniden
voluntarily parꢁcipates in
an RBRC® industry program
to collect and recycle used
Output
voltage
8V AC @ 8V AC @
300mA 300mA
Ni-MH baꢂeries within the
United States. Please call
1-800-8-BATTERY for informaꢁon on Ni-MH
baꢂery recycling in your area. (RBRC® is a
registered trademark of the Rechargeable
Baꢂery Recycling Corporaꢁon.)
Battery pack (normal use)
Part
number/
Capacity
BT-1021 (300mAh)
2.4V DC
Rechargeable batteries must be recycled
or disposed of properly.
Talk time
about 7 hours
Warning! The cords on this product and/
or accessories contain lead, a chemical
known to the state of California to cause
birth defects or other reproductive harm.
Wash hands after handling.
Uniden works to reduce lead content in
PVC coated cords in our products and
accessories.
Standby time about 6 days
Battery life about 1 year
x Use only the supplied AC adapters.
x Use the proper adapter for the base
and any chargers.
x Do not place the unit in direct
sunlight or subject it to high
temperatures.
x Replace the battery when the talk
or standby time becomes noticeably
reduced. For replacements, call the
Parts Department (see the front
cover).
x When the battery gets low, the
handset beeps or shows a low
battery alert; put the handset in the
cradle for recharging.
Compliance Informaꢀon
FCC Part 68 Informaꢀon
This equipment complies with Part 68
of the FCC rules and the requirements
adopted by the ACTA. On the boꢂom of this
equipment is a label that contains, among
other informaꢁon, a product idenꢁfier in the
format US: AAAEQ##TXXXX. If requested,
this number must be provided to the phone
company.
An applicable Universal Service Order Codes
(USOC) cerꢁficaꢁon for the jacks used in
this equipment is provided (i.e., RJ11C) in
the packaging with each piece of approved
terminal equipment. A plug and jack used
to connect this equipment to the premises
wiring and telephone network must comply
with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A
compliant telephone cord and modular plug
is provided with this product. It is designed
to be connected to a compaꢁble modular
jack that is also compliant. See installaꢁon
instrucꢁons for details.
Rechargeable Baꢂery Warning
x
This equipment contains a rechargeable
Nickel-Metal-Hydride (Ni-MH) baꢂery.
Nickel is a chemical known to the state of
California to cause cancer.
x
x
x
Do not short-circuit the baꢂery.
The baꢂeries in this equipment may explode if
disposed of in a fire.
Do not charge the baꢂeries in any charger
other than the one specified in the owner’s
manual. Using another charger may damage
the baꢂery or cause it to explode.
x
The REN is used to determine the number of
devices that may be connected to a phone
English - 15
line. Excessive RENs on a phone line may
result in devices not ringing in response to
an incoming call. In most but not all areas,
Any changes or modificaꢁons to this product
not expressly approved by the manufacturer
or other party responsible for compliance
the sum of RENs should not exceed five (5.0). could void your authority to operate this
To be certain of the number of devices that
may be connected to a line, as determined
by the total RENs, contact the telephone
provider. The REN for this product is part of
the product idenꢁfier that has the format
US:AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g.,
03 is a REN of 0.3).
product.
NOTICE: According to telephone company
reports, AC electrical surges, typically
resulꢁng from lightning strikes, are very
destrucꢁve to telephone equipment
connected to AC power sources. To minimize
damage from these types of surges, a surge
arrestor is recommended.
If this equipment causes harm to the
telephone network, the telephone company
will noꢁfy you in advance that temporary
disconꢁnuance of service may be required.
But if advance noꢁce isn't pracꢁcal, the
telephone company will noꢁfy the customer
as soon as possible. Also, you will be advised
of your right to file a complaint with the FCC
if you believe it is necessary. The telephone
company may make changes in its faciliꢁes,
equipment, operaꢁons or procedures that
could affect the operaꢁon of the equipment.
If this happens the telephone company will
provide advance noꢁce in order for you to
make necessary modificaꢁons to maintain
uninterrupted service.
Please follow instrucꢁons for repairing, if any
(e.g. baꢂery replacement secꢁon); otherwise
do not subsꢁtute or repair any parts of the
device except as specified in this manual.
Connecꢁon to party line service is subject to
state tariffs. Contact the state public uꢁlity
commission, public service commission or
corporaꢁon commission for informaꢁon. This
equipment is hearing aid compaꢁble.
If you experience trouble with this
FCC Part 15 Informaꢀon
This device complies with part 15 of the FCC
rules. Operaꢁon is subject to the following
two condiꢁons: (1) This device may not cause
harmful interference, and (2) This device must
accept any interference received, including
interference that may cause undesired
operaꢁon. Privacy of communicaꢁons may
not be ensured when using this phone.
FCC PART 15.105(b): Note: This equipment
has been tested and found to comply with
the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protecꢁon
against harmful interference in a residenꢁal
installaꢁon. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instrucꢁons, may cause harmful interference
to radio communicaꢁons. However, there
is no guarantee that interference will not
occur in a parꢁcular installaꢁon. If this
equipment does cause harmful interference
to radio or television recepꢁon, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct
the interference by one or more of the
following measures:
equipment, contact the manufacturer or
an authorized agent. If the equipment is
causing harm to the telephone network, the
telephone company may request that you
disconnect the equipment unꢁl the problem
is resolved.
x
x
Reorient or relocate the receiving antenna.
Increase the separaꢁon between the
equipment and receiver.
If your home has wired alarm equipment
connected to a phone line, be sure that
installing the system does not disable your
alarm equipment. If you have quesꢁons about
what will disable alarm equipment, contact
your telephone company or a qualified
installer.
x
x
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
16 - English
is subject to the following two condiꢁons: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause
undesired operaꢁon of the device. "Privacy of
communicaꢁons may not be ensured when
using this telephone."
RF Exposure Informaꢀon
This product complies with FCC radiaꢁon
exposure limits under the following
condiꢁons:
x
x
x
The base must be placed to allow a minimum
of 20 cm (8 inches) between the antenna and
all persons during normal operaꢁon.
The base must not be collocated or operated
in conjuncꢁon with any other antenna or
transmiꢂer.
The handset is designed for body-worn
operaꢁon and meets FCC RF exposure
guidelines when used with any belt clip,
carrying case, or other accessory supplied
with this product. (All necessary accessories
are included in the package; any addiꢁonal
or opꢁonal accessories are not required
for compliance with the guidelines.) Third
party accessories (unless approved by the
manufacturer) should be avoided as these
might not comply with FCC RF exposure
guidelines.
Warranty (1 Year, Limited)
Evidence of original purchase is required
for warranty service.
WARRANTOR: UNIDEN AMERICA
CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants,
for one year, to the original retail owner, this
Uniden Product to be free from defects in
materials and craſtsmanship with only the
limitaꢁons or exclusions set out below.
WARRANTY DURATION: This warranty to the
original user shall terminate and be of no
further effect 12 months aſter the date of
original retail sale. The warranty is invalid if
the Product is (A) damaged or not maintained
as reasonable or necessary, (B) modified,
altered, or used as part of any conversion
kits, subassemblies, or any configuraꢁons
not sold by Uniden, (C) improperly installed,
(D) serviced or repaired by someone other
than an authorized Uniden service center
for a defect or malfuncꢁon covered by this
warranty, (E) used in any conjuncꢁon with
equipment or parts or as part of any system
not manufactured by Uniden, or (F) installed
or programmed by anyone other than as
detailed by the owner's manual for this
product.
STATEMENT OF REMEDY: In the event
that the product does not conform to this
warranty at any ꢁme while this warranty is
in effect, warrantor will either, at its opꢁon,
repair or replace the defecꢁve unit and
return it to you without charge for parts,
service, or any other cost (except shipping
and handling) incurred by warrantor or
its representaꢁves in connecꢁon with the
performance of this warranty. Warrantor, at
its opꢁon, may replace the unit with a new
or refurbished unit. THE LIMITED WARRANTY
SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT
AND IS IN LIEU OF AND EXCLUDES ALL OTHER
Industry Canada (I.C.) Noꢀce
Terminal equipment
NOTICE: This equipment meets the applicable
Industry Canada Terminal Equipment
Technical Specificaꢁons. This is confirmed by
the registraꢁon number. The abbreviaꢁon
IC before the registraꢁon number signifies
that registraꢁon was performed based on
a Declaraꢁon of Conformity indicaꢁng that
Industry Canada technical specificaꢁons were
met. It does not imply that Industry Canada
approved the equipment.
NOTICE: The Ringer Equivalence Number
(REN) for this terminal equipment is marked
on the equipment itself. The REN assigned
to each terminal equipment provides an
indicaꢁon of the maximum number of
terminals allowed to be connected to a
telephone interface. The terminaꢁon on an
interface may consist of any combinaꢁon of
devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
Radio equipment
The term IC before the radio cerꢁficaꢁon
number only signifies that Industry Canada
technical specificaꢁons were met. Operaꢁon
English - 17
As an Energy Star® Partner, Uniden has
determined that this product meets the
Energy Star® guidelines for energy efficiency.
Energy Star® is a U.S.
WARRANTIES OF ANY NATURE WHATSOEVER,
WHETHER EXPRESS, IMPLIED OR ARISING
BY OPERATION OF LAW, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY
DOES NOT COVER OR PROVIDE FOR
THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or
limitaꢁon of incidental or consequenꢁal
damages so the above limitaꢁon or exclusion
may not apply to you.
registered mark.
x
x
Uniden® is a registered
trademark of Uniden
America Corporaꢁon.
The pictures in this
manual are for example only. Your phone may
not look exactly like the pictures.
LEGAL REMEDIES: This warranty gives you
specific legal rights, and you may also have
other rights which vary from state to state.
This warranty is void outside the United
States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE
OF WARRANTY: If, aſter following the
instrucꢁons in the owner's manual you
are certain that the Product is defecꢁve,
pack the Product carefully (preferably in its
original packaging). Disconnect the baꢂery
from the Product and separately secure the
baꢂery in its own separate packaging within
the shipping carton. The Product should
include all parts and accessories originally
packaged with the Product. Include evidence
of original purchase and a note describing the
defect that has caused you to return it. The
Product should be shipped freight prepaid, by
traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
18 - English
|