Ultra Start Automobile Alarm 430 User Manual

INSTALL GUIDE  
Covers All 430, 440, 441 and CJ Series  
Advanced Security Systems  
Technical Support: 866-698-5872 ext 0  
FCC/ID Notice  
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference that may cause  
undesired operation.  
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance  
void the user’s authority to operate this devise.  
 
REMOTE VEHICLE SECURITY  
INSTALL MANUAL  
PAGE 3  
For modules with 10 pin connector only. See page 4 for 11 pin connector.  
*500ma negative output  
Orange  
Gray  
(-) When Armed  
*500ma negative output  
Trunk Release  
Ignition Input  
Connect to vehicles ignition wire  
Connect to constant power. 20amp input  
Connect to Siren wire. 2amp Maximum  
Connect to chassis ground  
Yellow  
Red  
12 Volt Input  
Brown  
Black  
Siren Output  
Ground Input  
Door Input  
Connect to door pin. (+) when opened  
Connect to door pin. (-) when opened  
Connect to hood and / or trunk pin  
Purple  
Green  
Blue  
Door Input  
Hood Input  
 
INSTALL MANUAL  
PAGE 4  
REMOTE VEHICLE SECURITY  
For modules with 11 pin connector only.  
*500ma negative output  
(-) When Armed  
Orange  
Gray  
*500ma negative output  
Trunk Release  
12 Volt Input  
Connect to constant power. 20amp input  
Connect to Siren wire. 2amp Maximum  
Connect to chassis ground  
Red  
Brown  
Black  
Siren Output  
Ground Input  
Hood Input  
Connect to hood and / or trunk pin  
Blue  
Connect to door pin. (-) when opened  
Connect to vehicles ignition wire  
Green  
Door Input  
Ignition Input  
Door Input  
Dome Light  
Yellow  
Purple  
Blk/White  
Connect to door pin. (+) when opened  
Dome Light Supervision Output (-)  
Red  
Blue  
 
REMOTE VEHICLE SECURITY  
INSTALL MANUAL  
PAGE 5  
Wiring Descriptions  
10 Pin / *11 Pin Connector  
White  
Orange*  
Grey*  
Yellow  
Red  
Brown  
Black  
Purple  
Green  
Blue  
(+) Park lights  
(-) When Armed  
(-) Trunk Release  
(+) Ignition Input  
(+) 12Volt Input  
(+) Siren Output  
(-) Ground Input  
(+) Door Input  
(-) Door Input  
Park light output.  
Negative output when system is armed.  
Negative output for trunk release.  
Input from vehicles ignition wire.  
Constant 12 Volt input.  
Positive output for siren.  
System ground input.  
Positive door pin switch input.  
Negative door pin switch input.  
Negative input from hood pin switch.  
(-) Hood Input  
Blk/White* (-) Dome Supervision 30 second (-) output when disarmed.*  
*This wire is only available on models with the 11 pin connector.  
3 Pin Connector Red  
Green*  
Red*  
Blue*  
(-) Door Lock  
(+) 12 Volt Output  
(-) Door Unlock  
Door Lock Output (Programmable)  
12Volt Output for voltage inverter.  
Door Unlock Output (Programmable)  
*NOTE: 500ma outputs ONLY!  
Recommended Installation Procedures  
Mounting the module-Never mount the module in the engine compartment.  
Select a location under the dash to install the main module. Be certain that the  
module is securely attached and does not obstruct any serviceable areas.  
Mount the module so that it cannot be seen if looking under the dash as it could  
be easily unplugged by a thief. The module must be free from all moving parts.  
Under Hood Connections- Route the hood pin (optional) and Siren wire  
through the firewall, into the engine compartment. Always try to pull the wires  
through a factory rubber grommet. If drilling through the firewall, BE CAREFUL.  
Check for obstructions on both sides of the firewall. After drilling use a snap in  
grommet to protect the wires from sharp edges.  
Mounting the Siren- Choose a location in the engine compartment that is  
away from high heat sources and direct exposer to water. The siren should be  
mounted as well as grounded to solid metal. Run the wiring for the siren so that  
it can not be seen or reached from below the vehicle.  
 
INSTALL MANUAL  
PAGE 6  
REMOTE VEHICLE SECURITY  
Recommended Installation Procedures  
Installing the LED- Choose a location that will be highly visible when the  
LED is installed. Most vehicles are equipped with knock out panels in the  
dashboard, these panels are easily removable and can be easily replaced if  
necessary. Once the location is picked, use drill bit and drill a hole through the  
panel. Test fit the LED into the hole. Plug the Led into the Red connector on the  
main module.  
Installing the Program Button- Choose a location to mount the Program  
Button. This location should be hidden and not visible from outside the vehicle.  
Once the location of the switch is picked, use a 1/4” drill bit and drill a hole.  
Remove the nut and push the Program Button through the hole. Replace the  
nut and tighten until the switch is secure. Plug the Program Button into the  
Blue connector of the main module.  
Basic Install  
Step 1 - Connect All Of the Following Wires  
Black  
Yellow  
Red  
Ground Input  
Ignition Input  
Power Input  
System ground input.  
Input from vehicles ignition wire.  
Constant 12 Volt input.  
Brown  
White  
Green*  
Purple*  
(+) Siren Output Positive output for siren.  
(+) Park lights  
(-) Door Input  
(+) Door Input  
Positive park light output.  
Negative door pin switch input.  
Positive door pin switch input.  
*Test for door pin type (+ or -) then connect the appropriate wire.  
Step 2- Plug-In The Module  
Step 3- Test And Adjust The Shock Sensor (see page 3)  
Step 4- Test The System  
Your Basic Install Is Complete!  
 
REMOTE VEHICLE SECURITY  
INSTALL MANUAL  
PAGE 7  
Programming  
To Enter Program Mode  
1) Make sure ignition is in the off position.  
2) Within three seconds turn the key ON the OFF.  
3) Press and release the Program Button two times.  
4) The siren will chirp and the lights will flash once to confirm.  
NOTE: If unit does not enter Program Mode, repeat steps 2-3.  
** The ignition input wire(yellow on the 10 pin connector) MUST be connected.  
If it is not connected it will not be possible to enter the Program Mode.  
Changing A Programmable Setting  
1) Enter Program Mode As explained above.  
2) When in program Mode, change the desired Program Setting by pressing  
the transmitter buttons in the following sequences.  
NOTE: The Systems Default Setting Are Shown In Bold Lettering.  
#1  
#3  
#2  
#1 #2  
#3  
Quick View Programming  
Programmable Feature  
Shock Sensor Disable  
Arm / Disarm Chirps  
Ignition Auto Locks  
Door Lock Timing  
Double Pulse Unlock  
Door Input / Voltage Sense  
Passive / Active Locks  
Passive / Active Arming  
Car Jack Mode*  
Press Buttons  
One Chirp  
Two Chirps  
Enabled  
Chirps On  
On  
.75 Second  
Single Pulses  
Door Pin  
Passive  
#3-#3-#1  
#2-#1-#1  
#1-#3-#2  
#1-#3-#1  
#2-#2-#1  
#1-#1-#3  
#3-#3-#2  
#1-#2-#3  
#2-#1-#3  
#3-#2-#1  
#3-#3-#3  
Disabled  
Chirps Off  
Off  
3 Second  
Two Pulses  
Voltage  
Active  
Active  
Deactivated  
Siren  
Passive  
Activated  
Horn  
Siren/ Horn Output**  
System Reset  
Confirmed by Three Siren Chirps  
*CJ series ONLY  
**441 series ONLY  
 
INSTALL MANUAL  
PAGE 8  
Enter Program Mode  
REMOTE VEHICLE SECURITY  
Entering program mode is done by the following steps:  
1) Make sure ignition is in the off position.  
2) Turn the ignition key ON - OFF, leaving key in the OFF position.  
3) Press and release the Valet button two times.  
4) The siren will chirp one time to confirm entering program mode.  
( If this does not happen, turn ignition off, wait five seconds and repeat steps 1-4).  
Shock Sensor Disable  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence:  
#3 - #3 then #1  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Shock Sensor OFF  
Shock Sensor ON  
Arm/ Disarm Chirp  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#2 - #1 then #1  
3 - The siren will respond with the following:  
Chirps Disabled  
Chirps Enabled  
1 Chirp  
2 Chirps  
Ignition Auto Locks  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #3 then #2.  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Auto Lock Disabled  
Auto Lock Enabled  
Door Lock Timing  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #3 then #1  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
3 Second Door Locks  
0.75sec Pulses  
Double Pulse Unlock  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#2 - #2 then #1.  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Double Pulse Unlock  
Single Pulse Unlock  
NOTE: Repeat sequence to change selection  
 
REMOTE VEHICLE SECURITY  
INSTALL MANUAL  
PAGE 9  
Voltage / Door Pin Sensing  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #1 then #3  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Voltage Sensing- No Door Pin Connection Needed  
Door Pin- Door Pin Connection Required  
Passive / Active Locks  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#3 - #3 then #2  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Active Locks  
Passive Locks  
Passive / Active Arming  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #2 then #3  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Active Arming  
Passive Arming  
Car Jack Mode (CJ series ONLY)  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#2-#1 then #3  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Inactive  
Active  
Siren/ Horn Output (441 series ONLY)  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#3-#2 then #1  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Siren  
Horn  
Reset System  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#3-#3 then #3  
3 - The siren will respond with the following:  
3 Chirps  
System Reset  
NOTE: Repeat sequence to change selection  
 
INSTALL MANUAL  
PAGE 10  
REMOTE VEHICLE SECURITY  
Transmitter Programming  
Follow the steps below to program the transmitters to the system s memory  
Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.  
Step 2 - Press and release the Program Button twice then press and hold.  
Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.  
Note: If the siren does not respond, repeat Steps1&2  
Step 4 - Continue to hold the Program Button and press lock button on each of the  
transmitter’s to be programmed(Maximum of 3 Different transmitter codes).  
Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.  
Exit - After five seconds the system will exit transmitter program mode automatically.  
NOTE: You must program ALL of the transmitters to be used at one time. For the owner’s  
security any transmitters not programmed at this time will be erased from memory.  
*** This system will store a maximum of three transmitter codes in memory.  
Car Jack Mode Activation (CJ series ONLY).  
1) If the ignition key is On and a door is opened the Car Jack Mode  
Timer will start. The siren will chirp one every second for 10  
seconds then trigger into full alarm.  
2) If the timer was activated by accident, within 10 seconds turn the  
ignition key back to On then press and release the program  
button one time. The Car Jack Mode Timer will stop.  
3) If the timer is not deactivated Car Jack Mode will trigger into full  
alarm. To deactivate turn the ignition On, then press and release  
the program button 5 times then press unlock on the remote  
transmitter.  
Emergency Override.  
If Car Jack Mode is not deactivated in time, the system will need to  
be placed into Emergency Override. Turn the ignition key to the On  
position then press and hold the program button for 20seconds. At  
this time the customer can bring the vehicle back to the dealer for a  
system reset.  
 
REMOTE VEHICLE SECURITY  
INSTALL MANUAL  
PAGE 11  
Alarm Functions  
Arm  
1. Press and release the button.  
2. The park lights will flash and the siren will chirp one time.  
3. The doors will lock (optional).  
NOTE: The LED will start flashing within five seconds. If installed, the starter  
disable will activate.  
Disarm  
1.Press and release the button on the remote transmitter.  
2.The park lights will flash and the siren will chirp two times.  
3.The doors will unlock (optional).  
NOTE: The LED will stop flashing. If installed, the starter disable will deactivate.  
Silent Arm/Disarm  
1. Press and release the button then press and release the button to  
silent arm. The park lights will flash once to confirm.  
2. Press and release the button then press and release the button to  
silent disarm. The park lights will flash twice to confirm.  
Panic  
1. Press and hold the button on the remote transmitter.  
2. The park lights will flash and the siren will sound.  
3. Press and release the or the button to deactivate*.  
*Panic will be active for 60 seconds or until disabled by the remote transmitter.  
Trunk  
1. Press and hold the button for 3 seconds.  
2. The doors will unlock (optional), continue holding until the Trunk Release  
activates.  
Car Finder  
1. Press and hold the button for 3 seconds.  
2. The park lights will flash and the siren will chirp 5 times.  
 
INSTALL MANUAL  
PAGE 12  
REMOTE VEHICLE SECURITY  
Relay Wiring Diagrams  
Negative Type Door Locks  
Positive Type Door Locks  
87  
87  
87a  
86  
87a  
86  
85  
85  
30  
30  
5 Wire / Reverse Polarity Type Door Locks  
87  
87a  
87  
87a  
86  
86  
85  
85  
30  
30  
Negative Park Lights- In some cases the park lights may flash erratically after  
installing the negative park light relay. To correct this issue add a diode between the coil  
pins of the relay as shown.  
Ground  
Add IN4001 Diode  
as shown  
87  
87a  
86  
85  
White  
30  
Negative park light output  
 

Tascam Computer Monitor DA 78HR User Manual
TOA Electronics Stereo Amplifier BG 1030 User Manual
Toshiba Laptop 4000 4005WLMi User Manual
Toshiba MP3 Player DMF102XKU User Manual
TP Link Music Mixer RX 7 248 User Manual
Triarch Indoor Furnishings 29585 GOLD User Manual
Uniden Scanner UBC3500XLT User Manual
Vidikron Projection Television 40 HT User Manual
ViewSonic Car Video System CDE4600 L User Manual
Weber Gas Grill 55159 User Manual