TOS HIBA
Storage Device Division
DVD-RAM
DRIVE
SD-W2002
Installation Instructions
withVOB InstantWrite
and
TM
CyberLink PowerDVD Software
VERSION 3.0
JANUARY 2002
Disclaimer and limitation of remedy
ALL OTHER EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
AND/OR NONINFRINGEMENT OF THIRD PARTY RIGHTS, ARE HEREBY DISCLAIMED.
TOSHIBA EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN
DURATION TO THE TERM OF THIS EXPRESS LIMITED WARRANTY. SOME COUNTRIES,
STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE EXCLUSIONS
OR LIMITATIONS MAY NOT APPLY TO YOU. YOU MUST READ AND FOLLOW ALL SET-UP AND
USAGE INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR MANUALS ENCLOSED.
IF YOU FAIL TO DO SO, THIS PRODUCT MAY NOT FUNCTION PROPERLY AND YOU MAY
LOSE DATA OR SUFFER OTHER DAMAGE. TOSHIBA, ITS AFFILIATES AND SUPPLIERS DO
NOT WARRANT THAT OPERATION OF THIS PRODUCT WILL BE UNINTERRUPTED OR ERROR
FREE.
IF THIS PRODUCT FAILS TO WORK AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE
REMEDY SHALL BE REPAIR OR REPLACEMENT. IN NO EVENT WILL TOSHIBA, ITS
AFFILIATES OR SUPPLIERS BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES
IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO
DAMAGES OF ANY KIND WHATSOEVER INCLUDING (1) DAMAGE TO, OR LOSS OR CORRUP-
TION OF, YOUR RECORDS, PROGRAMS, DATA OR REMOVABLE STORAGE MEDIA, OR (2)
ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL,
INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF
WARRANTY, CONTRACT, TORT OR OTHERWISE, OR WHETHER ARISING OUT OF THE USE
OF OR INABILITY TO USE SUCH PRODUCT AND/OR THE ENCLOSED USER GUIDES AND/OR
MANUALS, EVEN IF TOSHIBA, OR AN AUTHORIZED TOSHIBA REPRESENTATIVE, AUTHO-
RIZED SERVICE PARTNER OR DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.
SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS, SO THE ABOVE
EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM COUNTRY/STATE/JURISDICTION TO COUNTRY/STATE/JURISDICTION.
Protection of Stored Data
For your important data, please make periodic back-up copies of all the data stored on the
hard disk or other storage devices as a precaution against possible failures, alteration, or loss
of the data. IF YOUR DATA IS ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR
MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA
CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS
OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR
TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS
BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY
FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.
CriticalApplications
The Product you have purchased is not designed for any “critical applications.” “Critical
applications” means life support systems, medical applications, connections to implanted
medical devices, commercial transportation, nuclear facilities or systems or any other
applications where product failure could lead to injury to persons or loss of life or cata-
strophic property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLIERS
DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE PRODUCT IN ANY
CRITICAL APPLICATIONS. IF YOU USE THE PRODUCT IN A CRITICAL APPLICATION, YOU,
AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.
Table of Contents
Kit Packaging .............................................................................................. 1
System Requirements .................................................................................. 1
Setting Jumpers ........................................................................................... 2
Connecting Cables ....................................................................................... 3
Completing Installation............................................................................... 5
DVD-RAM Front Panel ................................................................................ 6
DVD-RAM Rear Panel ................................................................................. 6
Operating the DVD Loading Tray .............................................................. 7
Specifications ............................................................................................... 8
Technical Support Info ................................................................................ 8
Repair Center ............................................................................................... 8
Warranty ...................................................................................................... 9
LASERCAUTION
Thisappliancecontainsalasersystemandisclassifiedasa"CLASS1LASERPRODUCT".To
use this model properly, read this Owner's Manual carefully and keep this manual for future
reference. Incaseofanytroublewiththismodel,pleasecontactyournearest"AuthorizedRepair
Center". Topreventdirectexposuretothelaserbeam,donottrytoopentheenclosure.
CAUTION!
•
•
REFLECTIVE OBJECTS SHOULD NOT BE PLACED IN THE DISK
SLOT DUE TO POSSIBLE HAZARDOUS
RADIATION EXPOSURE.
USE OF CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED IN THIS MANUAL MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
Version
01
DatePublished
November2000
December2000
January2002
RevisedContents
Initialrelease
AddWarning/NoticeInfo
TAECtoTAIS
02
03
ii
Congratulations on your purchase of a Toshiba DVD-RAM drive and Kit. The
following information will help you in the simple installation of your new DVD-
RAM drive.
CHECKINGYOUR KIT PACKAGING
Please unpack your DVD-RAM kit, and assure that you have the following items:
!
!
!
!
!
!
!
!
!
Toshiba SD-W2002 DVD-RAM Drive
Blank Media - Single Sided/Type 1 DVD-RAM
CyberLink PowerDVD™ Software
VOB InstantWrite Software CD
DVD-RAM Installation Instructions (this manual)
Quick Start Guide
Mounting screws (4)
IDE BUS cable
DVD/CD sound cable
Additional items you may need that are not included in the kit are:
! Phillips Screwdriver
! Mounting hardware (i.e. some computer systems use mounting rails).
SYSTEM REQUIREMENTS
The DVD-RAM kit requires the following:
✔ At least 55MB of free hard disk space
✔ At least 32MB of RAM
✔ *Pentium II processor at 266MHz or higher or....
*Celeron 300A processor or higher or....
*K6-2 processor at 300MHz or higher
✔ Display card supporting DirectDraw
✔ 16-bit or better sound card
✔ Microsoft™ Windows 95 or higher
✔ Amplified stereo speakers
* These requirements are only required if you are using the CyberLink PowerDVD™
software. The SD-W2002 DVD-RAM will work as a CD-ROM and DVD-RAM
when using a lower speed Pentium system.
1
The following steps must be performed to properly install your DVD-RAM.
✔ Set drive’s jumpers
✔ Connect audio cable
✔ Attach IDE BUS cable
✔ Connect power cable
✔ Mount DVD-RAM
✔ Install CyberLink PowerDVD™ software (used for viewing DVD movies)
✔ InstallVOB InstantWritesoftware (used for recording CDs)
SETTING JUMPERS
The mode select jumpers are six (6) straight angle pins located on the rear of the
DVD-RAM. By placing a jumper on the pins, you can select the following func-
tions:
CS: – Drive is configured using host interface signal CSEL
SL: – Configures drive as Slave
MA: – Configures drive as Master (default mode)
C
S
S
L
M
A
Mode Select Jumpers
In most installations, jumper should remain in MA (Master) position (factory
default). It is recommended that you install your DVD-RAM only on the second-
ary IDE BUS. If you are installing on primary IDE BUS, your hard drive would
then be the Master, and you should set your DVD-RAM to the Slave position (SL).
PLACING DVD-RAM INSIDE YOUR COMPUTER
Now that you have set your drive’s jumpers, you are ready to install your
DVD-RAM inside your computer.
IMPORTANT: Disconnect power from your computer system before be-
ginning installation.
✔
2
1. Remove computer cover and faceplate if required (refer to your computer
system’s manual for removal information).
2. If the DVD-RAM is replacing a CD-ROM, disconnect all connectors and re-
move the CD-ROM presently installed in your system.
3. Your Toshiba DVD-RAM can be placed in any free half-height drive slot at the
front of your computer. (It can be mounted horizontally or vertically.)
4. Carefully start sliding the DVD-RAM into the opening with the disc tray facing
the front of the computer. Before you push the drive all the way in you will
need to connect the IDE BUS cable, audio cable and the power cable to the
back of the drive.
CONNECTING CABLES
Cable Locations on Rear of DVD-RAM
IDE BUS (Data) Cable - Most computer system have a primary and secondary
IDE BUS cable already installed (an IDE BUS cable is include with your kit if your
system does not have a secondary IDE BUS cable).
If you are replacing a CD-ROM: connect the DVD-RAM drive using the BUS
cable that the CD-ROM was connected to. Insure that the jumper setting of the
DVD-RAM is the same as the CD-ROM drive you are replacing.
If the DVD-RAM is not replacing a CD-ROM and/or is in addition to a CD-ROM:
locate the secondary IDE BUS cable in your system. If your system does not have
a secondary IDE BUS cable installed, you will need to install the IDE BUS cable
that was included with your kit.
Installing secondary IDE BUS cable: locate the secondary IDE BUS connec-
tor on your system’s motherboard (refer to your system’s documentation for
location). Connect one end of the IDE BUS cable to motherboard, assuring
that it is keyed properly and that cable’s colored edge is aligned with Pin 1.
Connect secondary IDE BUS cable to DVD-RAM drive, assuring that pin 1 of the
3
cable (side with red stripe) is connected to pin 1 on the drive.
• If the DVD-RAM is the only drive connected on the secondary IDE BUS
cable: connect drive to the last set of pins on IDE BUS cable.
• If there is a device (i.e. CD-ROM) connected to the secondary IDE BUS
cable: connect DVD-RAM to the open middle connector . The DVD-RAM
drive should then be jumpered to SL (slave) position.
If the DVD-RAM is to be the slave on the Primary BUS: connect the DVD-RAM to
the open connector on the primary IDE BUS cable. The DVD-RAM drive should be
jumpered to the SL (slave) position. Note: the primary IDE BUS cable, in most
cases, will be connected to your hard drive. The hard drive will be the Master on
the primary BUS.
Power Cable - Inside your computer system, locate an unused power supply cable.
Connect the power cable to the power socket at the back of the DVD-RAM. One
side of the plug has chamfered edges, so the power connector fits only one way so
be sure to insert the DC power plug in the correct direction. Push plug completely
into the socket making sure the plug fits correctly.
Audio Cable - Connecting your DVD-RAM to your sound card allows you to play
audio CDs on your computer (speakers or headphones are also needed).
If the DVD-RAM is in addition to a CD-ROM: If you choose to have both a CD-
ROM and DVD-RAM installed in your system, in most circumstances, only one
audio cable can be used (there are some sound cards that will allow you to have
two audio connections). You must decide which device you would like to hear
audio from and connect the audio cable from the sound card to the CD-ROM or
DVD-RAM (DVD audio is transmitted through the data cable, not the audio cable).
If the DVD-RAM is to be the only CD-ROM device in your system:
• If replacing a CD-ROM that had an audio cable connection: connect DVD-
RAM drive to the audio cable that the CD-ROM was connected. Cable con-
nects to the analog audio connector at the left rear of the DVD-RAM (see
Cable Location photo on page 3 for location).
• If you do not have an audio cable presently in your system: connect the DVD-
RAM using the audio cable that was included with this kit. Connect one end
to your sound card and the other end to the analog audio connector at the left
rear of the DVD-RAM (see Cable Location photo on page 3 for location).
Refer to the instructions which came with your sound card for details on any
sound-driver software required.
4
COMPLETING INSTALLATION
After you have connected all the necessary cables, push the DVD-RAM com-
pletely into the computer’s drive slot. Mount the drive per your computer’s in-
structions using the screws included in your kit. If you are using other screws,
assure that the screw length does not exceed 3±0.5mm (measured from outside
surface of side or bottom of DVD-RAM to tip of screw). Replace the computer
cover and all outer screws.
ATAPI CD/DVD Software Driver:
Toshiba’s DVD-RAM drives do not require any unique device drivers for Win-
dows '95/'98/2000/NT. After installing your drive and re-booting, your system
should recognize your drive. Win '95/'98/2000/NT operating systems support all
ToshibaATAPI CD-RW, CD-ROM, DVD-ROM and DVD-RAM drives natively.
VOB InstantWrite Software:
VOB’s InstantWrite software is used to record DVDs with your new DVD-RAM
drive. Before installing VOB Software it is recommended that you visit VOB’s
website to check for any software updates (www.vobinc.com). To install software
insert the installation CD into your newly installed DVD-RAM. If “Autorun” is
enabled on your system, the Installation window will appear automatically. If it
does not appear, go to Windows Start menu, select “Run” and type d:\setup.exe
(substitute the appropriate letter of your DVD-RAM drive for d:). From the Instal-
lation window select Instant Write and follow the installation instructions that
appear on your screen. For additional information on this software, please refer to
the documentation found on the VOB “Instant Write” CD.
VOB InstantBackup Software:
VOB’s InstantBackup allows you to backup your valuable data to CD/DVD. Backup
of selected files and folders or the complete hard drive is possible. Supports both
incremental and random write-strategies.
CyberLink PowerDVD™:
CyberLink PowerDVD™ is a high-quality, pure-software DVD player that brings
high-quality movies and karaoke into your multimedia PC. You can playback
high resolution DVD titles or MPEG-2 files with superb MPEG-2 video and Dolby
AC-3 audio quality.
Before installing CyberLink software it is recommended that you visit CyberLink’s
insert CyberLink PowerDVD™ into your newly installed DVD-RAM. Go to Win-
dows Start menu, select “Run” and type d:\setup.exe(substitute the appropri-
ate letter of your DVD-RAM drive for d:). Follow the installation instructions on
screen. For additional information on using this software, please refer to the
PowerDVD™ Help file (if you have opened PowerDVD™ software, click “?”).
5
DVD-RAM FRONT PANEL
The photo below illustrates the following features of the SD-W2002 DVD-RAM’s
front panel:
Emergency Eject Hole: The emergency eject hole is to be used only when the DVD
tray will not open when the Load/Unload button is pressed. Insert solid bar (i.e.
paper clip) into hole, applying gentle presure, until tray opens. Do not use Emer-
gency Eject Procedure while the drive is in operation.
Loading Tray: Load disc using tray or recording cartridge
Load/Unload Button: Used to open the disc tray so you can install or remove a
disc or recording cartridge.
Busy Indiactor: Provides status of drive.
DVD-RAM BACK PANEL
The photo below illustrates the following features of the SD-W2002 DVD-RAMs
back panel:
Digital Audio Out Connector: Outputs Digital Audio on the DVD-RAM.
Analog Audio Out Connector: Outputs Analog Audio on the DVD-RAM.
ATAPI Connector: Connects DVD-RAM to computer.
Power Connector: Connects DVD-RAM to power source.
Mode Select Jumper: Selects if drive is to be Master, Slave or Cable Select.
6
OPERATING THE DVD LOADING TRAY
To open the DVD loading tray, just press the Load/Unload button. After inserting
or removing a disc or recording cartridge, press the Load/Unload button again.
You must use a DVD-RAM recording cartridge when recording DVD-RAM media.
Vertical Disc Installations
When placing a disc into a DVD-RAM drive that has been mounted vertically, be
assured that the disc in installed under the two front tabs.
DVD-RAM MEDIA
After installing the VOB and CyberLink software your system is ready to use.
Some important things to remember when using your DVD-RAM Drive:
! Do not insert more than one disc into the drive at a time.
! Do not insert anything other than a CD or DVD disc into drive.
! Use media that is the correct size and shape.
! Use media that meets write/read requirements listed in the Specifications
(see page 8)
.
7
SPECIFICATIONS
DVD
CD
DATA CAPACITY
2,048bytes/block
mode 1: 2,048bytes/block
mode 2: 2,336bytes/block
ROTATIONAL
SPEED (RPM)
DVD-RAM (2.0): 1,380 - 3,300 CD-ROM, CD-R: 5,100
2,100 - 3,300 CD-RW: 3,400
DVD-RAM (1.0): 1,080 - 2,400 Video CD: 900 - 2,000
DVD-ROM (single): 2,400
DVD-ROM (double): 3,800
DVD-R,DVD-RW: 1,100 - 2,800
CD-DA: 1,800 - 4,200
SUSTAINED DATA DVD-RAM(2.1) 2,704
mode 1: 1,557 - 3600
mode 2: 1775 - 4,140
TRANSFER RATE
(kbytes/sec)
DVD-RAM (1.0) 1,352
DVD-ROM: 2,812 - 6,760
ACCESS TIME (typ) DVD-RAM
DVD-ROM
120ms
100ms
CD-ROM
100ms
85ms
Avg. Random Access
Avg Random Seek
Avg. Full Stroke
190ms
145ms
330ms
200ms
180ms
DATA BUFFER
POWER SUPPLY
MTBF
8Mbytes
+5v, +12v
100,000 hours
DIMENSIONS
WEIGHT
5.7” x 1.6” x 7.68” (146mm x 41.5mm x 195mm)(Wx H x D)
2.5lbs (1.15kg)
MOUNTING ORT.
APPLICABLE
±10° vertical / ±15° horizontal
DVD Specifications for rewritable Disc Part 1, Ver 2.1:
WRITE/READ DISC 4.7Gbyte x 1 & 1.46Gbyte x 1 (one side, there is cartridge/none)
4.7Gbyte x 2 & 1.46Gbyte x 2 (both side, there is cartridge/none)
DVD Specifications for rewritable Disc Part 1, Ver 1.0
2.6Gbyte x 1 (one side, there is cartridge/none)
2.6Gbyte x 2 (both side, there is cartridge/none)
APPLICABLE
DVD-ROM, DVD-R(3.9GB), DVD-RW (4.7GB)
READ ONLY DISC
CD-DA, CD+(E)G, CD-MIDI,CD-TEXT, CD-ROM, CD-ROM-XA,
MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, CD-EXTRA, Portfolio, CD-R,
CD-RW), CD-R, CD-RW
TECHNICAL SUPPORT
Technical support can be obtained by calling 949/455-0407 or by sending an
email to: [email protected] or visiting our website at:
REPAIR CENTER
Should your DVD-RAM require maintenance, contact Toshiba SDD’s Repair Cen-
ter. In order to return your DVD-RAM, a ReturnAuthorization Number (RA#) must
be obtained from the Repair Center (do not send drive without an authorized RA
number.
Phone: 510/651-6798
Fax: 510/623-9893
e-mail: [email protected]
8
9
460020-C0
P/N 460020-C0
|