Toshiba Camera Accessories ik tf7u User Manual

INSTRUCTION MANUAL  
CAMERA CONTROL UNIT  
IK-TF7U  
For Customer Use  
Enter below the Serial #  
which is located on the  
bottom of the cabinet. Retain  
this information for future  
reference.  
Model #:  
Serial #:  
IK-TF7U  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-  
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
USER-INSTALLER CAUTION:Your authority to operate this FCC verified equipment could be voided  
if you make changes or modifications not expressly approved by the party responsible for compliance  
to Part 15 of the FCC Rules.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.  
Following information is only for EU-member states:  
The use of the symbol indicates that this product may not be treated as household waste.  
By ensuring this product is disposed of correctly, you will help prevent potential negative con-  
sequences for the environment and human health, which could otherwise be caused by inap-  
propriate waste handling of this product. For more detailed information about the takeback  
and recycling of this product, please contact your supplier where you purchased the product  
or consult.  
This manual is made from 100% recycled paper.  
 
Note the following instructions when installing.  
• Do not cover the product with any material.  
• Do not place the product on any confined Inflammable material such as a  
carpet or blanket.  
• Do not place the product in a narrow space, as this may cause heat to buildup  
inside the product.  
Failure to follow the above cautions may result in fire.  
Do not place the product in direct sunshine and/or high temperature.  
Temperature build up inside the product may result in fire.  
Avoid placing in humid, smoky, vaporized or dusty places.  
This may result in fire and/or electric shock.  
Ask your dealer to perform a periodical check and internal cleaning (approx.  
once every five years).  
Dust inside the product may result in fire. For check and cleaning cost, please  
consult your dealer.  
The following description is for that a camera head “IK-TF7H” connected to this camera control unit.  
Do not point the lens directly at the sun and/or intensive light such as di-  
rect sunlight, etc.  
Focusing of the light may cause eye injury and/or fire.  
Disclaimer  
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the  
user in any of the following cases:  
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-  
tional or accidental; use under extreme operating conditions.  
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including  
but not limited to loss of expected income and suspension of business activities.  
3. Incorrect use not in compliance with instructions in this instruction manual.  
4. Malfunctions resulting from misconnection to other equipment.  
5. Repairs or modifications made by the user or caused to be made by the user and carried out by  
an unauthorized third party.  
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the  
purchase price of the product.  
Limitation of Usage  
The product is not designed for any “critical applications.Critical applications” means life support  
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass  
transit applications, military applications, homeland security applications, nuclear facilities or sys-  
tems or any other applications where product failure could lead to injury to persons or less of life or  
catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out  
of the use of the product in any critical applications.  
Protection of Personal Information  
Images taken by the camera that reveal the likeness of an individual person may be considered  
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,  
consent of the person may be required.  
3
 
Copyright and Right of Portrait  
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,  
distributes, or exhibits an image picked up by the camera without permission from the copyright  
holder. Please also note that transfer of an image or file covered by copyright is restricted to use  
within the scope permitted by the Copyright Law.  
TABLE OF CONTENTS  
1. CAUTIONS ON USE AND INSTALLATION ..... 5  
2. COMPONENTS ................................................ 5  
3. NAMES AND FUNCTIONS .............................. 6  
4. CONNECTION .................................................. 7  
(4. 4) Changing B pedestal ........................ 22  
(4. 5) Changing the shading  
correction mode ............................... 23  
(4. 6) Changing the manual shading correction  
seting ................................................ 23  
( 5 ) SYNC ...................................................... 23  
(5. 1) Adjusting horizontal phase............... 23  
4. 1 Standard Connection ................................ 7  
4. 2 Cautions on Connection ........................... 7  
4. 3 Connector Pin Assignments ..................... 7  
( 6 ) OPTION .................................................. 23  
(6. 1) Changing serial communication baud  
rate .................................................... 23  
5. OPERATION ..................................................... 8  
( 7 ) Returning to factory settings ................... 24  
7. 3 Synchro. Scan Operation ........................ 24  
( 1 ) Setting by 1H .......................................... 24  
( 2 ) Setting by the frame ................................ 24  
7. 4 E. TRG (External trigger)......................... 25  
5. 1 Automatic Black Balance .......................... 8  
5. 2 White Balance........................................... 8  
5. 3 Gain ........................................................ 10  
5. 4 Sading Correction ................................... 10  
6. ITEMS CONTROLLED BY THE SCREEN  
DISPLAY ......................................................... 11  
( 1 ) 1P SNR  
(1 Pulse Trigger Sync Non Reset)........... 25  
(1. 1) 1 Pulse Trigger SYNC-NON RESET  
Picture Output Timing ...................... 25  
7. MODE SETTING BY THE SCREEN DISPLAY .. 12  
7. 1 Using the Menus ..................................... 12  
7. 2 Menus ..................................................... 13  
( 1 ) SHUTTER (Electronic shutter)................ 13  
(1. 1) Changing the setting in  
( 2 ) 1P SR (1 Pulse Trigger Sync Reset) ....... 26  
(2. 1) 1 Pulse Trigger SYNC-RESET Picture  
Output Timing ................................... 26  
( 3 ) PW SNR (Pulse width trigger  
MANU mode ..................................... 14  
(1. 2) Changing the setting in  
SS (synchro. scan) mode ................. 15  
(1. 3) Changing the setting in  
SYNC-NON RESET) .............................. 27  
(3. 1) Pulse Width Trigger SYNC-NON RESET  
Picture Output Timing ...................... 27  
E.TRG mode..................................... 16  
(1. 3. 1) Changing the setting in  
1P SNR mode ............................... 16  
(1. 3. 2) Changing the setting in  
( 4 ) PW SR (Pulse width trigger  
SYNC-RESET) ....................................... 28  
(4. 1) 1 Pulse Width Trigger SYNC-RESET  
Picture Output Timing ...................... 28  
1P SR mode ................................. 17  
(1. 3. 3) Changing the setting in  
PW SNR mode ............................. 18  
(1. 3. 4) Changing the setting in  
PW SR mode ................................ 19  
(1. 3. 5) Changing the setting in  
( 5 ) RR (Reset restart) .................................. 29  
(5. 1) Long Term Exposure ........................ 29  
(5. 2) Input Timing Chart Example ............ 29  
7. 5 Partial Read ............................................ 30  
( 1 ) Partial Scanning OFF  
(All pixels scanning) ................................ 30  
RR mode ....................................... 19  
( 2 ) Partial Scanning ON ............................... 30  
( 3 ) When Partial Scanning Mode is ON ....... 30  
7. 6 External Sync .......................................... 31  
( 1 ) External sync signal polarity ................... 31  
( 2 ) External sync frequency range ............... 31  
( 2 ) GAIN (Video gain)................................... 20  
(2. 1) Changing the setting in GAIN .......... 20  
( 3 ) WHT BAL (White balance)...................... 21  
(3. 1) Changing the setting in AWB  
(Automatic White Balance) mode .... 21  
(3. 2) Changing the setting in MANU  
(Manual) mode ................................. 21  
( 3 ) Using the unit with external sync signal .. 31  
(3. 1) H (horizontal) phase adjustment...... 31  
( 4 ) PROCESS .............................................. 22  
(4. 1) Changing gamma correction ............ 22  
(4. 2) Changing master pedestal ............... 22  
(4. 3) Changing R pedestal ........................ 22  
8. INPUT OUTPUT SIGNAL SPECIFICATIONS .... 32  
( 1 ) HD Input Specifications .......................... 32  
( 2 ) VD Input Specifications........................... 32  
4
 
( 3 ) Trigger Pulse Specifications.................... 32  
( 2 ) Vertical Output Waveform Timing Chart... 33  
( 4 ) External HD/VD Input Phase  
10. SPECIFICATIONS ....................................... 34  
Specifications.......................................... 32  
11. EXTERNAL APPEARANCE DIAGRAM...... 35  
12. BEFORE MAKING A SERVICE CALL ........ 35  
9. OUTPUT WAVEFORM TIMING CHART............. 33  
( 1 ) Horizontal Output Waveform Timing Chart ... 33  
This product is 3CCD color camera with digital video output.  
1. CAUTIONS ON USE AND INSTALLATION  
Handling the unit.  
The following descriptions are for that a camera head  
“IK-TF7H” connected to this camera control unit.  
Do not drop, jolt, or vibrate, as this may result in  
damage to the unit. This may cause problems.  
Treat the camera cables carefully to prevent cable  
problems, such as breaks in the cable and loose  
connections.  
Do not shoot intense light.  
If there is an intense light at a location on the  
screen such as a spot light, a blooming and smear-  
ing may occur. When intense light enters, vertical  
stripes may appear on the screen. This is not a  
malfunction. Ghosts may occur when there is an  
intense light near the object. In this case, change  
the shooting angle.  
Install the camera in a location free from noise.  
If the camera or the cables are located near power  
utility lines or a TV, etc. undesirable noise may  
appear on the screen. In such a case, try to change  
the location of the camera or the cable wiring.  
Moire  
Operating ambient temperature and humidity.  
A moire pattern is an interference pattern gener-  
ated when two repetitive line patterns overlap.This  
is not a malfunction. Eliminating the repetitive line  
patterns, or aligning the two patterns, will elimi-  
nate the moire.  
Do not use the camera in places where tempera-  
ture and humidity exceed the specifications. Pic-  
ture quality will deteriolate and internal parts may  
be damaged.  
Handling of the camera head and protection  
cap.  
Be particularly careful when using in places ex-  
posed to direct sunlight. When shooting in hot  
places, depending on the conditions of the object  
and the camera (for example when the gain is in-  
creased), noise in the form of vertical strips or  
white dots may occur. This is not a malfunction.  
Keep the camera head and protection cap away  
from as they may pose a choking hazard.The pro-  
tection cap protects the image sensing plane when  
the lens is removed from the camera head, do not  
discard.  
When not using the camera for extended peri-  
ods of time.  
When cleaning the camera.  
Switch the control unit off and disconnect the  
power supply.  
Unplug the power source before cleaning. Clean  
with a soft dry cloth only. Do not use chemicals or  
chemically treated cloths. Chemicals may damage  
coatings and printed letters. When cleaning the  
lens, use lens cleaning paper.  
Avoid using or storing the camera in the fol-  
lowing places:  
Places filled with highly flammable and corrosive  
gas.  
Installation without a tripod.  
Before installing the camera head and the cam-  
era control unit, make sure that the location can  
withstand the total weight of the camera head and  
the camera control unit.  
Places near gasoline, benzene, or paint thinner.  
Places subject to strong vibration.  
Places containing chemicals (such as pesticides),  
rubber or vinyl products for extended periods of  
time.  
If this is not the case, reinforce the area to pre-  
vent the unit from dropping, which may result in  
damage to the unit or personal injury.  
2. COMPONENTS  
(1) Camera Control Unit ......................................................................................................................1  
(2) Accessories  
(a) Instruction manual ...................................................................................................................1  
5
 
3. NAMES AND FUNCTIONS  
8
2
4
DC IN 12V terminal  
DISP button  
1 Camera cable for  
‘IK-TF7H’ terminal  
MENU UP button  
(AWB)  
DISP  
6
7
DATA UP (AWB) button  
DATA DOWN button  
MENU DATA  
DC IN 12V  
PAGE  
5 MENU DOWN button  
9
DIGITAL terminal  
3 PAGE button  
[ Front ]  
[ Rear ]  
10  
11  
[ Bottom ]  
Camera cable for ‘IK-TF7H’ terminal  
DISP button  
Where the camera cable for ‘IK-TF7H’ is connected.  
To change the display mode.  
1
2
3
4
5
6
PAGE button  
To switch and select menus.  
MENU UP button  
To select the function to be confirmed or changed on the menu.  
To select the function to be confirmed or changed on the menu.  
MENU DOWN button  
DATA UP (AWB) button  
To change the value of the function selected by the MENU (UP/DOWN)  
button. (Also used when using AWB.)  
DATA DOWN (ABB) button  
To change the value of the function selected by the MENU (UP/DOWN)  
button. (Also used when using ABB)  
7
DC IN 12V terminal  
DIGITAL terminal  
Accept a DC power input (12V).  
8
9
8-bit RGB, digital signal, and sync signal are output in the Camera  
Link format.  
Trigger signal is input.  
Mode switching signal for partial scanning is input.  
Accepts serial communication control signal.  
Used to fix the camera.  
Mounting holes M3  
Mounting holes M2  
!
"
Used to fix the camera.  
6
 
4. CONNECTION  
4. 1 Standard Connection  
Camera control unit  
Lans  
(option)  
Cable  
(option)  
Camera cable  
for IK-TF7U  
IK-TF7U  
(option)  
Monitor  
Frame grabber board,  
image process  
IK-TF7H  
(option)  
equipment etc.  
DC IN 12V  
When connection the frame grabber  
board, image process equipment, etc  
with power supply function, refer to the  
item “4.2 Caution on Connection”.  
DC power  
supply (option)  
4. 2 Cautions on Connection  
• Only use optional camera head model # IK-TF7H with this camera controller.  
The use of another head may cause damage to the control unit and camera head.  
• When connecting the camera cables, be sure to turn off the camera control unit and any other equipment  
connected to it.  
• For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounded  
type AC adaptor with the specifications described below.  
Power supply voltage  
Current rating  
Ripple voltage  
: 12V DC 10%  
: More than 830mA  
: Less than 50mV(p–p)  
To connect DC IN 12V terminal, use the following connector listed below.  
Connector : HR10A–7P–4S by HIROSE electronics Co., Ltd  
Pins 1, 2 : 12V , Pins 3, 4 : GND  
• If the securing screw on the connector of the camera cable loosens, noise may appear on the screen.  
Be sure to tighten the connector completely.  
• Use the standard cable for Camera Link.  
• Input DC power (12V) either DC IN 12V terminal or DIGITAL terminal. If DC power is supplied input  
from both terminals, it may cause trouble.  
• More than 830mA is necessary for proper functioning of the unit. Use power line with sufficient quan-  
tities of current rating. The unit dose not support PoCL standard.  
4. 3 Connector Pin Assignments  
DIGITAL  
Function  
I/O  
O
O
O
O
O
I
DC IN 12V  
13 GND  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
GND  
X0+  
1
2
3
4
+12V  
2
3
4
5
6
7
8
9
X0-  
+12V  
GND  
GND  
X1-  
X1+  
13  
26  
1
X2-  
X2+  
Xclk-  
X3-  
Xclk+  
X3+  
14  
SerTC+  
SerTFC-  
CC1-  
SerTC-  
SerTFC  
CC1+  
CC2-  
CC3+  
CC4-  
+12V  
Serial communication control (RXD)  
Serial communication control (TXD)  
Trigger pulse input  
1
2
4
3
+
O
I
Connector used:  
12226-51000-00  
10 CC2+  
11 CC3-  
12 CC4+  
Partial scanning control  
External HD input  
I
(3M) or equivalent.  
I
Connector used:  
I
External VD input  
HR10A-7R-4PB  
+12V  
1
(HIROSE electronics  
Co. Ltd) or equivalent.  
7
 
5. OPERATION  
A camera head “IK-TF7H” is supposed to be connected to this camera control unit from this section.  
Refer to the item " 4. CONNECTION", connect each equipment correctly.  
Turn on the connected equipment and the power source of the camera.  
1
2
3
When using the camera for the first time and when replacing the camera cable and the camera head, be  
sure to operate the ABB adjustment refer to the item "Automatic Black Barance".  
Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc..  
Refer to the item "5.1 White Balance", make the adjustment.  
4
5
6
Refer to the items "7. MODE SETTING BY ON SCREEN DISPLAY", select the necessary items.  
5. 1 Automatic Black Balance  
Black balance adjustment is necessary to get the correct black picture level.  
• Close the lens iris and put the lens cover on.  
• If the index menu/menu is displayed, press the [DISP] button to disable or the character display.  
• Hold the [DATA DOWN] button for approx. 1 second.  
• When the black balance adjustment operation starts, the character ABB blinks on the screen.  
• When the black balance adjustment operation finishes, the character ABB stops blinking and the result  
appears for approx. 1 second.  
• When the black balance adjustment performed, set the electronic shutter, Synchro. Scan, partial read to  
OFF, and do not operate trigger mode or external sync.  
• When using the camera for the first time and when replacing the camera cable and the camera head, be  
sure to operate the ABB adjustment refer to the item "Automatic Black Barance".  
Display  
ABB OK  
Meaning  
Automatic black balance adjustment finished correctly.  
ABB NG  
CLOSE LENS  
Automatic black balance adjustment cannot be performed because the  
lens iris is open. Close the lens iris.  
ABB NG  
Automatic black balance adjustment cannot be performed.  
Operate the automatic black balance again.  
5. 2 White Balance  
For the white balance adjustment of this unit, AWB (Automatic White Balance) and MANU (Manual white  
balance) adjustments are provided. To select the desired mode, refer to the items "7.2 (3) WHT BAL (White  
balance)" and "7. MODE SETTING BY ON SCREEN DISPLAY".  
AWB  
MANU  
(Automatic White Balance)  
(Manual White Balance)  
Outline  
Note  
Adjust white balance by displaying the  
white object inside the area set by AWB  
menu and pressing the [DATA UP] button. white object.  
Adjust the white balance manually using  
the WHT BAL menu while shooting the  
When the shutter mode is E.TRG, AWB is Adjustment is performed by confirming  
not available.  
with a monitor etc.  
8
 
AWB (Automatic white balance)  
1
• Set the MODE to AWB on the WHT BAL menu.  
Perform the C.TEMP (color temperature conversion) setting, if necessary.  
(Refer to the item "7.2 (3) WHT BAL (White balance)".)  
3200K : Appropriate for indoor shooting.  
5600K : Appropriate for outdoor shooting.  
• If the index menu/menu is displayed, press the [DISP] button to disable the character display on the  
menu.  
• Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.  
• The character AWB blinks on the screen when the AWB starts.  
• The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1  
second.  
Result displayed  
Meaning  
AWB OK  
Automatic white balance adjustment finished correctly.  
AWB NG LEVEL  
LOW  
Automatic white balance adjustment cannot be performed because the  
video level is too low.  
Obtain the proper video level.  
AWB NG  
LEVEL HIGH  
Automatic white balance adjustment cannot be performed because the  
video level is too high.  
Obtain the proper video level.  
AWB NG  
C. TEMP LOW  
Automatic white balance adjustment cannot be performed because the  
color temperature is too low.  
If the C.TEMP is set to 5600K, set to 3200K.  
If the message appears with the C.TEMP set to 3200K, change the  
illumination or use a color temperature conversion filter.  
AWB NG  
C. TEMP HIGH  
Automatic white balance adjustment cannot be performed because the  
color temperature is too high.  
If the C.TEMP is set to 3200K, set to 5600K.  
If the message appears with the C.TEMP set to 5600K, change the  
illumination or use the color temperature conversion filter.  
AWB NG  
NOT AVAILABLE  
Automatic white balance adjustment cannot be performed because the  
shutter speed mode is E.TRG mode.  
AWB NG  
Automatic white balance adjustment cannot be performed for other  
reasons. Such as no white area is included in an object, etc.  
MANU (Manual white balance)  
2
• Set the MODE to MANU on the WHT BAL menu.  
(Refer to the item "7.2 (3) WHT BAL (white balance)".)  
• Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the  
menu, confirming with a monitor etc.  
(Refer to the item "7.2 (3) (3.2) Changing each setting in MANU (Manual) mode".)  
9
 
5. 3 Gain  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.  
For the gain adjustment of the unit, MANU (Manual) and OFF (0 dB) modes are provided. Select the mode on  
the GAIN menu. (Refer to the item "7.2 (2) GAIN (Video gain)".)  
MANU (Manual gain)  
1
2
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.  
(Refer to the item "7.2 (2) (2.1) (a) Changing the gain in MANU mode".)  
OFF  
Gain is fixed at 0 dB.  
5. 4 Shading Correction  
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of  
the screen. In this case, the shading correction can decrease the color shading. For the shading correction of  
the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided. Select the  
mode on the PROCESS menu. (Refer to the item "7.2 (4) (4.5) Changing the shading correction mode".)  
MANU (Manual Shading)  
1
Adjust the correction amount on the PROCESS menu by confirming with a monitor or a waveform monitor.  
(Refer to the "7.2 (4) (4.6) Changing the manual shading correction setting".)  
OFF  
2
The status is no shading correction.  
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with SHAD.  
OFF for variable lens conditions.  
10  
 
6. ITEMS CONTROLLED BY THE SCREEN DISPLAY  
Preset value  
(Factory setting)  
Item  
MODE  
E. TRG  
MANU speed  
Available selections  
MANU, SS, E. TRG  
1P SNR, 1P SR, PW SNR, PW SR, RR  
OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s,  
MANU  
1P SNR  
OFF  
1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/1000000s  
Syncro. Partial read OFF 1H/796H~795H/796H, OFF, 2FRM~512FRM  
OFF  
scan.  
Partial read 40fps 1H/580H~579H/580H, OFF, 2FRM~512FRM  
Partial read 50fps 1H/465H~464H/465H, OFF, 2FRM~512FRM  
Partial read 60fps 1H/387H~386H/387H, OFF, 2FRM~512FRM  
Partial read 70fps 1H/332H~331H/332H, OFF, 2FRM~512FRM  
Partial read 80fps 1H/290H~289H/290H, OFF, 2FRM~512FRM  
Partial read 90fps 1H/258H~257H/258H, OFF, 2FRM~512FRM  
Partial read  
OFF, 40fps, 50fps, 60fps, 70fps, 80fps, 90fps,  
E40fps, E50fps, E60fps, E70fps, E80fps, E90fps  
OFF  
Trigger  
(1P SNR/SR)  
Trigger  
(PW SNR/SR)  
,
,
1P  
30 ms  
0.01ms~30ms  
exposure time  
MODE  
MANU  
MODE  
Color temperature  
MANUAL R GAIN  
MANUAL B GAIN  
GAMMA  
Master pedestal  
R pedestal  
MANU, OFF  
0dB~18dB  
AWB, MANU  
3200K, 5600K  
-100~0~100  
-100~0~100  
ON, OFF  
OFF  
0dB  
AWB  
3200K  
0
0
OFF  
0
-64~0~64  
-64~0~64  
0
B pedestal  
-64~0~64  
0
Shading correction  
mode  
MANU, OFF  
MANU  
Manual shading  
correction  
H phase adjustment  
-128~0~127  
0
0
-100~0~100  
Baud rate  
9600 bps, 19200 bps  
9600 bps  
11  
 
7. MODE SETTING BY THE SCREEN DISPLAY  
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The  
contents once set are memorized even if the power source is turned off, so it is unnecessary to set again when  
using the unit next time. When the setting is performed, select the menu of the item to be set.  
7. 1 Using the Menus  
When the power is turned on, the normal screen showing only the video signal appears. Change the output to  
each screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], and  
[MENU DOWN] buttons.  
* A menu is selected when pushing the [PAGE] button after moving the "" on the screen by the [MENU UP],  
[MENU DOWN] button while the Index menu is displayed.  
POWER ON  
Video signal output  
Index menu  
DISP  
DISP  
DISP  
PAGE  
PAGE  
Menues  
PAGE  
WHT BAL  
SHUTTER  
GAIN  
PROCESS  
SYNC  
INT  
OPTION  
SHAD.  
MANU  
BAUD  
RATE  
PAGE  
PAGE  
MANU  
PAGE  
AWB  
PAGE  
MANU  
SS  
PAGE  
SHAD.  
OFF  
EXT  
MANU  
OFF  
E. TRG  
1P SR  
E. TRG  
1P SNR  
E. TRG  
PW SR  
E. TRG  
PW SNR  
E. TRG  
RR  
12  
 
7. 2 Menus  
• Select the menu to change the setting by referring to the item "7.1 Using the Menus".)  
• When the [MENU UP], [MENU DOWN] buttons are pushed, the "" on the screen moves up and down.  
Move the "" to the item whose setting you wish to change.  
Note:  
When performing the mode setting in the menu display while selecting ON in "PART" (Partial Read:  
refer to page 30) and E.TRG in "MODE", the screen display and camera operation switch to normal  
mode. After close the MENU, they return to previous mode.  
( 1 ) SHUTTER (Electronic shutter)  
The electronic shutter has three modes; MANU (Manual), SS (Synchro. Scan), E.TRG (External trigger).  
Move the "" to "MODE" and push [DATA UP], [DATA DOWN] button to select the desired mode among  
"MANU", "SS", "E.TRG".  
MANUAL  
:
It is possible to select the exposure time from eleven speed setting; OFF, 1/100s, 1/250s,  
1/500s, 1/1000s, 1/2000s, 1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/100000s.  
Note:  
When setting a rapid shutter speed, sensitivity degrades according to the speed.  
When a discharging light such as fluorescent lamp, etc. is used for the illumination,  
the flicker may be large.  
SS  
:
:
Shutter speed can be set by the horizontal scanning time (1H) unit or by the frame unit.  
E.TRG  
Exposure is performed and images are output by external trigger. E.TRG includes the five  
modes described below. (For details of specifications, refer to the item “7.4 E.TRG  
(External trigger)”.)  
• 1P SNR (1 Pulse Sync Non Reset)  
The charge begins to accumulate after the trigger pulse is received, and 1 frame images  
are output according to the internal vertical sync signal timing. The exposure/accumula-  
tion time can be set from 0.01 to 30 ms. The trigger signal timing can be set to either the  
rising or falling edge.  
• 1P SR (1 Pulse Sync Reset)  
The charge begins to accumulate after the trigger pulse is received. Upon completion of  
accumulation the vertical sync signal is reset and 1 frame images are output. The  
exposure/accumulation time can be set from 0.01 to 30 ms. The trigger signal timing can  
be set to either the rising or falling edge.  
• PW SNR (Pulse width trigger Sync Non Reset)  
The charge begins to accumulate after the trigger pulse is received, and 1 frame images  
are output according to the internal vertical sync signal timing. This is the mode to set  
the exposure period by the pulse width of the trigger. The trigger signal polarity can be  
set to either the positive or negative polarity.  
• PW SR (Pulse width trigger Sync Reset)  
The charge begins to accumulate after the trigger pulse is received. Upon completion of  
accumulation the vertical sync signal is reset and 1 frame images are output. This is the  
mode to set the exposure period by the pulse width of the trigger. The trigger signal  
polarity can be set to either the positive or negative polarity.  
• RR (Reset restart)  
Input of an external reset-restart signal permits one screen of information to be output  
at an arbitrary timing.  
13  
 
(1. 1) Changing the setting in MANU mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Sutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• Sutter speed setting  
OFF, 100 (1/100s), 250 (1/250s), 500 (1/500s)  
1000 (1/1000s), 2000 (1/2000s), 4000 (1/4000s)  
10000 (1/10000s), 25000 (1/25000s)  
50000 (1/50000s)100000 (1/100000s)  
MODE  
MANU  
PART  
MANU  
100  
OFF  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
<MODE = MANUAL>  
(a) Changing the shutter speed  
Move the "" to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Partial scanning setting  
Move the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.  
14  
 
(1. 2) Changing the setting in SS (synchro. scan) mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
-- SHUTTER --  
MODE  
SS  
PART  
SS  
OFF  
OFF  
• Sutter mode MANU, SS, E.TRG  
• Synchro. scanning setting  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
<MODE = SS>  
(a) Changing the shutter speed setting  
Move the "" to SS by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Partial scanning setting  
Move the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a charac-  
teristic of CCD, and is not a symptom of malfunction.  
15  
 
(1. 3) Changing the setting in E.TRG mode  
The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR.  
First move the "" to MODE and select E. TRG, then move the "" to E.TRG and select the desired E.TRG  
mode.  
(1. 3. 1) Changing the setting in 1P SNR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Sutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
1P SNR, 1P SR, PW SNR, PW SR, RR  
MODE  
E.TRG  
TRG.P  
EXP.  
PART  
E.TRG  
1P SNR  
• Input trigger pulse setting at 1P SNR and 1P SR  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
30ms  
OFF  
• Exposure time setting at 1P SNR and 1P SR  
0.01 ms  
0.01 ms 0.02 ms  
step step  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
0.02 ms  
0.4 ms  
0.1 ms 1 ms  
step step  
1 ms  
20 ms  
2 ms  
step  
30 ms  
<MODE = E.TRG E.TRG = 1P SNR>  
(a) Changing the polarity of inputting trigger pulse setting  
Move the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing 1P SNR exposure time setting  
Move the "" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the exposure time by pushing [DATA UP], [DATA DOWN] buttons.  
(c) Changing the partial scanning setting  
Move the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.  
16  
 
(1. 3. 2) Changing the setting in 1P SR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Sutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
1P SNR, 1P SR, PW SNR, PW SR, RR  
MODE  
E.TRG  
TRG.P  
EXP.  
PART  
E.TRG  
1P SR  
• Input trigger pulse setting at 1P SNR and 1P SR  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
30ms  
OFF  
• Exposure time setting at 1P SNR and 1P SR  
0.01 ms  
0.01 ms 0.02 ms  
step step  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
0.02 ms  
0.4 ms  
0.1 ms 1 ms  
step step  
1 ms  
20 ms  
2 ms  
step  
30 ms  
<MODE = E.TRG E.TRG = 1P SR>  
(a) Changing the polarity of inputting trigger pulse setting  
Move the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing 1P SR exposure time setting  
Move the "" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the exposure time by pushing [DATA UP], [DATA DOWN] buttons.  
(c) Changing the partial scanning setting  
Move the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.  
17  
 
(1. 3. 3) Changing the setting in PW SNR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Sutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
MODE  
E.TRG  
PW SNR  
1P SNR, 1P SR, PW SNR, PW SR, RR  
E.TRG  
TRG.P  
PART  
• Input trigger pulse setting at PW SNR and PW SR  
Input trigger pulse : positive polarity  
OFF  
Input trigger pulse : negative polarity  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
<MODE = E.TRG E.TRG = PW SNR>  
(a) Changing the polarity of inputting trigger pulse setting  
Move the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the partial scanning setting  
Move the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
18  
 
(1. 3. 4) Changing the setting in PW SR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Sutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
MODE  
E.TRG  
PW SR  
1P SNR, 1P SR, PW SNR, PW SR, RR  
E.TRG  
TRG.P  
PART  
• Input trigger pulse setting at PW SNR and PW SR  
OFF  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
<MODE = E.TRG E.TRG = PW SR>  
(a) Changing the polarity of inputting trigger pulse setting  
Move the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
(1. 3. 5) Changing the setting in RR mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
MODE  
E.TRG  
PART  
E.TRG  
RR  
OFF  
1P SNR, 1P SR, PW SNR, PW SR, RR  
• Partial scanning switch  
OFF/40fps/50fps/60fps/70fps/80fps/90fps/  
E40fps/E50fps/E60fps/E70fps/E80fps/E90fps  
<MODE = E.TRG E.TRG = RR>  
(a) Changing the partial scanning setting  
Move the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
19  
 
( 2 ) GAIN (Video gain)  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.  
For the gain adjustment of the unit, MANU (Manual) and OFF (0dB) modes are provided.  
1 MANU (Manual gain)  
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.  
2 OFF  
Gain is fixed at 0dB.  
Move the "" to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between  
MANU and OFF.  
(2. 1) Changing the setting in GAIN  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
-- GAIN --  
MODE  
MANU  
MANU  
0dB  
• Gain mode MANU, OFF  
• Manual gain adjustment 0 dB to 18 dB (1 dB step)  
(a) Changing the gain in MANU mode  
Move the "" to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the manual gain by pushing [DATA UP], [DATA DOWN] buttons.  
20  
 
( 3 ) WHT BAL (White balance)  
WHT BAL has two modes; AWB, MANU.  
Move the "" to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between AWB  
and MANU.  
(3. 1) Changing the setting in AWB (Automatic White Balance) mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value pushing  
DATA UP, DOWN  
-- WHT BAL --  
MODE  
AWB  
0
0
• White balance mode (AWB, MANU)  
R GAIN  
B GAIN  
C.TEMP  
Automatically adjusting value for red gain and blue gain  
are shown on the screen  
3200  
* These values may not be changed during AWB mode.  
• Color temperature setting 3200, 5600  
(a) Changing color temperature setting  
Move the "" to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either 3200 or 5600 by pushing [DATA UP], [DATA DOWN] buttons.  
(3. 2) Changing the setting in MANU (Manual) mode  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
-- WHT BAL --  
MODE  
MANU  
• White balance mode AWB, MANU  
• Red gain adjustment -100 to 100  
• Blue gain adjustment -100 to 100  
• Color temperature setting 3200, 5600  
R GAIN  
B GAIN  
C. TEMP  
0
0
3200  
(a) Changing the red gain  
Move the "" to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the red gain by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the blue gain  
Move the "" to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the blue gain by pushing [DATA UP], [DATA DOWN] buttons.  
21  
 
( 4 ) PROCESS  
• Gamma Correction (GAMMA)  
Select either OFF or ON of Gamma Correction.  
• Master Pedestal (M. PED)  
Adjust the Pedestal level of each RGB.  
• R Pedestal (R. PED)  
Adjust the Pedestal level of Red.  
• B Pedestal (B. PED)  
Adjust the Pedestal level of Blue.  
• Shading Correction (SHAD.)  
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom  
of the screen. In this case, the shading correction can decrease the color shading. For the shading correction  
of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided.  
MANU (Manual Shading)  
1
Adjust the correction amount on the PROCESS menu by confirming with a monitor or a waveform monitor.  
OFF  
2
The status is no shading correction.  
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with  
SHAD. OFF for variable lens conditions.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
• Gamma correction ON/OFF  
-- PROCESS --  
• Master pedestal adjustment -64 to 64  
• R pedestal adjustment -64 to 64  
GAMMA  
M.PED  
R.PED  
B.PED  
SHAD.  
MANU  
OFF  
0
0
0
MANU  
0
• B pedestal adjustment -64 to 64  
• Shading mode setting MANU/OFF  
• Manual shading adjustment -128 to 127  
(4. 1) Changing gamma correction  
Move the "" to GAMMA by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the gamma correction by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 2) Changing master pedestal  
Move the "" to M. PED by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 3) Changing R pedestal  
Move the "" to R. PED by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 4) Changing B pedestal  
Move the "" to B. PED by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
22  
 
(4. 5) Changing the shading correction mode  
Move the "" to SHAD. by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the SHAD. by pushing [DATA UP], [DATA DOWN] buttons.  
Note: The alignment value for shading is fixed to "0" when selecting SHAD. OFF. MANU is not dis-  
played in the menu.  
(4. 6) Changing the manual shading correction setting  
Move the "" to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.  
( 5 ) SYNC  
When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external  
sync) automatically.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
-- SYNC --  
MODE  
EXT  
• Sync system display  
H PHASE  
0
• H PHASE adjustment -100 to 100  
(5. 1) Adjusting horizontal phase  
Move the "" to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.  
( 6 ) OPTION  
(6. 1) Changing serial communication baud rate  
Move the "" to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.  
Move up down  
by pushing  
MENU UP, DOWN  
Select the desired  
value by pushing  
DATA UP, DOWN  
-- OPTION --  
BAUD RATE  
9600  
• Serial baud rate setting 9600, 19200  
23  
 
( 7 ) Returning to factory settings  
All the settings can be returned to the factory default status (preset status).  
(1) If characters are displayed on the screen, press the [DISP] button to disable the character display.  
(2) Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.  
(3) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed  
for approx. 1 second.  
7. 3 Synchro. Scan Operation  
The shutter speed can be set by the horizontal scanning period (1H) or by the frame.  
( 1 ) Setting by 1H  
1H/796H ~ 795H/796H stands for the setting by the 1H and the shutter speed can be set by the 1H (43.05 µs).  
When operating Partial Scannig, the number’s listed below can be used for setting.  
Partial scanning OFF  
40fps, E40fps  
50fps, E50fps  
60fps, E60fps  
70fps, E70fps  
80fps, E80fps  
90fps, E90fps  
1H/796H ~ 795H/796H  
1H/580H ~ 579H/580H  
1H/465H ~ 464H/465H  
1H/387H ~ 386H/387H  
1H/332H ~ 331H/332H  
1H/290H ~ 289H/290H  
1H/258H ~ 257H/258H  
( 2 ) Setting by the frame  
2FRM to 512FRM stand for the setting (long period exposure) by the frame.  
The video signal stored during the frame period set is output as 1 frame video image at a frame interval  
specified.  
(Internal VD)  
n
n+1  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DAVL  
(4FRM setting)  
24  
 
7. 4 E. TRG (External trigger)  
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are  
output. There are four modes: 1P SNR, 1P SR, PW SNR, PW SR.  
( 1 ) 1P SNR (1 Pulse Trigger Sync Non Reset)  
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are  
output.  
(1. 1) 1 Pulse Trigger SYNC-NON RESET Picture Output Timing  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 1 µs  
Exposure period*2  
Exposure period*2  
External HD IN*1  
External VD IN*1  
About 1H  
(Internal VD)  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
28H (Partial scanning OFF  
)
The internal VD falling edge is within the  
exposure period and thus video is not output.  
24H (Partial scanning 40fps)  
32H (Partial scanning 50fps)  
38H (Partial scanning 60fps)  
42H (Partial scanning 70fps)  
44H (Partial scanning 80fps)  
47H (Partial scanning 90fps)  
3
*
*1: Externally input signal  
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and FVAL/LVAL/DVAL have a paired relationship.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
25  
 
( 2 ) 1P SR (1 Pulse Trigger Sync Reset)  
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, the vertical sync signal is  
reset and frame images are output.  
(2. 1) 1 Pulse Trigger SYNC-RESET Picture Output Timing  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 1 µs  
Exposure period*2  
Exposure completion  
0 to 1H*3  
(Internal VD)  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
28H (Partial scanning OFF  
)
24H (Partial scanning 40fps)  
32H (Partial scanning 50fps)  
38H (Partial scanning 60fps)  
42H (Partial scanning 70fps)  
44H (Partial scanning 80fps)  
47H (Partial scanning 90fps)  
*1: Externally input signal  
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".  
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchro-  
nized to this and output.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
26  
 
( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET)  
The trigger input to CC1 of the DIGITAL terminal develops 1 frame images.  
(3. 1) Pulse Width Trigger SYNC-NON RESET Picture Output Timing  
Negative polarity mode  
Positive polarity mode  
Trigger*1  
About 7 µs  
About 1 µs  
Exposure period*2  
Exposure period*2  
External HD IN*1  
External VD IN*1  
(Internal VD)  
About 1H  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
28H (Partial scanning OFF  
)
The internal VD falling edge is within the  
exposure period and thus video is not output.  
24H (Partial scanning 40fps)  
32H (Partial scanning 50fps)  
38H (Partial scanning 60fps)  
42H (Partial scanning 70fps)  
44H (Partial scanning 80fps)  
47H (Partial scanning 90fps)  
3
*
*1: Externally input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and FVAL/LVAL/DVAL have a paired relationship.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
27  
 
( 4 ) PW SR (Pulse width trigger SYNC-RESET)  
The trigger input to the CC1 of the DIGITAL terminal develops 1 frame images.  
(4. 1) 1 Pulse Width Trigger SYNC-RESET Picture Output Timing  
Negative polarity mode  
Positive polarity mode  
Trigger*1  
About 1 µs  
About 7 µs  
Exposure period*2  
Exposure completion  
0 to 1H  
3
(Internal VD)  
*
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
28H (Partial scanning OFF  
)
24H (Partial scanning 40fps)  
32H (Partial scanning 50fps)  
38H (Partial scanning 60fps)  
42H (Partial scanning 70fps)  
44H (Partial scanning 80fps)  
47H (Partial scanning 90fps)  
*1: Externally input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchro-  
nized to this and output.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
28  
 
( 5 ) RR (Reset restart)  
Input of an external reset-restart signal (CC4 of the DIGITAL terminal: External VD input) permits one screen  
of information to be output at an arbitrary timing.  
(5. 1) Long Term Exposure  
When a sufficient sensitivity is not obtained with the normal operation conditions or capturing the trial of a  
moving subject is desired, the reset-restart function allows high-sensitivity images by extending the exposure  
time. To achieve this, please input from an external source a VD signal that has an expanded VD pulse and VD  
pulse interval.  
(5. 2) Input Timing Chart Example  
External HD IN  
External VD IN  
V reset  
V reset  
About 1H  
About 1H  
(Internal VD)  
Exposure period  
Exposure period  
Exposure period  
RGB data  
(video interval image)  
FVAL  
LVAL,  
DVAL  
1 frame  
1 frame= 796H (Partial scanning OFF  
)
580H (Partial scanning 40fps)  
465H (Partial scanning 50fps)  
387H (Partial scanning 60fps)  
332H (Partial scanning 70fps)  
290H (Partial scanning 80fps)  
258H (Partial scanning 90fps)  
External VD interval: more than 1 frame  
29  
 
7. 5 Partial Read  
( 1 ) Partial Scanning OFF (All pixels scanning)  
In this mode, all pixels independent signal from the DIGITAL connector is output each 1/29.2 second (Line  
order output).  
Video interval  
image  
1/29.2s (796H)  
( 2 ) Partial Scanning ON  
In this mode, the pixel signal of the vertical center portion from the DIGITAL connector is output.  
In the E.✽✽fps mode, the partial scanning and the all pixels scanning can be switched by the DIGITAL terminal  
(CC2: partial scanning control signal).  
CC2  
E.40fps  
E.50fps  
E.60fps  
E.70fps  
E.80fps  
E.90fps  
‘L’ Partial scanning 40fps Partial scanning 50fps Partial scanning 60fps Partial scanning 70fps Partial scanning 80fps Partial scanning 90fps  
‘H’ All pixels scanning All pixels scanning All pixels scanning All pixels scanning All pixels scanning All pixels scanning  
Video interval  
image  
1/40s (580H): When 40fps is selected  
1/50s (465H): When 50fps is selected  
1/60s (387H): When 60fps is selected  
1/70s (332H): When 70fps is selected  
1/80s (290H): When 80fps is selected  
1/90s (258H): When 90fps is selected  
( 3 ) When Partial Scanning Mode is ON  
(Internal VD)  
FVAL  
LVAL,  
DVAL  
RGB data  
(video interval image)  
Blanking interval  
Video interval Blanking interval  
B
C
D
Total  
A
Video period  
Mode  
40fps  
50fps  
60fps  
70fps  
80fps  
90fps  
Total A  
580H  
465H  
387H  
332H  
290H  
258H  
Blanking interval B Video interval C Blanking interval D  
24H  
32H  
38H  
42H  
44H  
47H  
542H  
412H  
322H  
259H  
211H  
175H  
14H  
21H  
27H  
31H  
35H  
36H  
30  
 
7. 6 External Sync  
When using the unit with an external sync signal, input HD and VD to CC3 and CC4 of the DIGITAL terminal.  
When the external sync signal is input, the camera automatically switches its sync from the internal sync to the  
external sync.  
The operation is as shown below, depending on the unit's status and how external sync signals are input.  
Shutter mode  
At time of SYNC-NON  
RESET mode  
HD input VD input  
Note  
N
Y
N
Y
N
Y
Y
N
Internal sync mode  
External sync mode  
Only V reset is applied due to VD input. Normally not used.  
HD is synchronized to external, but video is not output  
because there is no VD input. Normally not used.  
At time of SYNC-RESET  
mode  
N
Y
Internal sync mode. The presence of VD is ignored, and after  
a specified time after a trigger input, V reset is applied.  
*
*
HD is synchronized to external. The presence of VD is  
ignored, and after a specified time after a trigger input, V  
reset is applied.  
At time of reset restart  
Y
N
Y
Y
N
HD is synchronized to external. Video is output due to VD  
input.  
HD is synchronized to the inside of the camera. Video is  
output due to VD input.  
Video is not output because there is no VD input. Normally  
not used.  
*
At time of manual  
shutter  
N
Y
Y
N
N
Y
N
Y
Internal sync mode  
External sync mode  
HD is synchronized to external. Normally not used.  
Disabled  
Either Y or N is permitted.  
*
( 1 ) External sync signal polarity  
HD: 2 to 5V(p-p) Negative  
VD: 2 to 5V(p-p) Negative  
( 2 ) External sync frequency range  
(External sync with HD, VD)  
Within 1% (at horizontal sync frequency of 23.229 kHz)  
( 3 ) Using the unit with external sync signal  
When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase".  
(3. 1) H (horizontal) phase adjustment  
External  
Sync. signal  
Observe the external sync signal and the LVAL signal output  
Match  
waveform of the unit with a dual trace oscilloscope, and ad-  
the phase.  
just H phase so that the H phases match.  
LVAL signal  
output  
31  
 
8. INPUT OUTPUT SIGNAL SPECIFICATOINS  
( 2 ) VD Input Specifications  
( 1 ) HD Input Specifications  
2.0µs 5.0µs  
5H 21H  
( 3 ) Trigger Pulse Specifications  
(Positive polarity mode)  
More than 2 µs  
(Negative polarity mode)  
More than 2 µs  
( 4 ) External HD/VD Input Phase Specifications  
External HD  
rising edge  
100  
100  
External HD  
Unit : Clock  
1 clk=33.9nsec  
Center  
The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD falling  
edge) as illustrated in the above diagram.  
External VD falling edge:  
Please input within about 100 clock cycles of the standard center phase.  
Note that V sync of the video is output with a delay of about 2H from the external VD at the time of reset-restart and  
the external trigger mode.  
In the normal mode:  
Continuously with the HD period of 43.05 µs and VD period of 34.27 ms (partial scanning 40fps: 24.97 ms, 50fps:  
20.02 ms, 60fps: 16.66 ms, 70fps: 14.29 ms, 80fps: 12.49 ms, 90fps: 11.11 ms).  
Phase timing is as illustrated in the above diagram (with only the falling edge applicable).  
In the reset-restart/external trigger mode:  
Continuously with the HD period of 43.05 µs. VD (reset) is at an arbitrary timing with the phase of HD being within the  
standard of the above diagram.  
32  
 
9. OUTPUT WAVEFORM TIMING CHART  
( 1 ) Horizontal Output Waveform Timing Chart  
One horizontal scan interval 1270 clk  
(43.05 µs)  
LVAL,  
DVAL  
246 clk  
(8.34µs)  
33.9 ns  
29 clk 3 clk  
40 clk  
164 clk  
CCD  
output signal  
5 clk  
5
clk  
Optical black Horizontal transfer Dummy  
portion  
stop interval  
pixels  
Total effective pixels 1034 clk  
Optical black  
portion  
Horizontal blanking interval 246 clk  
Output video interval 1024 clk  
(8.34 µs)  
(34.71 µs)  
RGB data  
Pixel  
Clock  
CLK=33.9 ns  
(29.5 MHz)  
( 2 ) Vertical Output Waveform Timing Chart  
796H  
28H  
(1205µs)  
FVAL  
LVAL,  
DVAL  
768H  
CCD  
output signal  
1
1
2
3
4
5
6
7
1
1
2
3
4
5
6
7
Dummy  
pixels  
Dummy  
pixels  
Optical black  
portion  
Optical black  
portion  
Optical black  
portion  
Optical black  
portion  
Vertical blanking interval 28H  
Vertical blanking interval 28H  
(1205µs)  
(1205µs)  
RGB data  
33  
 
10. SPECIFICATIONS  
Power supply  
12V DC 10%  
Power consumption  
Pick-up system  
Image sensor  
Approx. 6.1W  
RGB, 3CCD  
1/3inch All pixels CCD  
(Effective pixels Horizontal : 1034, Vertical : 779)  
Scanning System  
Video output pixels  
Pixel clock frequency  
Sync signal frequency  
Sync system  
Progressive scan  
Horizontal pixels : 1024, Vertical : 768  
29.5MHz  
Horizotal : 23.229KHz, Vertical : 29.18Hz  
Internal/External (Automatic switching)  
F6.8 standard (2000 lx, 3000K)  
14 lx (F2.2, Sensitivity + 18 dB, 3000K)  
C mount (flange back : 17.526 mm in-air)  
0 to 40°C (32 to 104°F)  
Sensitivity  
Minimum illumination  
Lens mount  
Ambient temperature  
Ambient humidity  
Weight  
Less than 90%  
Approx. 160g (0.353lbs)  
External dimension  
44 (W) x 44 (H) x 78 (D) mm  
(1.73” (W) x 1.73” (H) x 3.07” (D)) (except for protruded portion)  
White balance  
Gain  
AWB (Automatic white balance), MANUAL (Manual)  
MANUAL (Manual), OFF (0 dB)  
Partial scanning  
Output signal  
Sync signal output  
40fps, 50fps, 60fps, 70fps, 80fps, 90fps  
8-bit RGB, Digital output (Camera Link format)  
FVAL, LVAL, DVAL (Positive polarity)  
Pixel Clock  
External sync input  
HD : CC3 (LVDS input) Negative polarity  
VD : CC4 (LVDS input) Negative polarity  
External trigger input  
CC1 (LVDS input), More than 2 µs pulse width  
Partial scanning control CC2 (LVDS input)  
signal input  
Interface  
Serial data interface : Ser TC (RXD), Ser TFG (TXD)  
IK-TF7H (CAMERA HEAD) EXC-CL05S (Cable), etc  
Optional parts  
The designs and specifications are subject to change without notice.  
34  
 
11. EXTERNAL APPEARANCE DIAGRAM  
Unit : mm [inch]  
4.8 [0.19]  
6.3  
[0.25]  
5.3  
[0.21]  
44 [1.73]  
78 [3.07]  
12 [0.47]  
4.8 [0.19]  
2-M2  
4.5 [0.18]  
56 [2.20]  
4-M3 Depth 3  
19.2  
[0.76]  
* inch = mm/25.4  
4-M2 Depth 3  
24.5  
[0.96]  
25  
[0.98]  
12. BEFORE MAKING A SERVICE CALL  
Symptom  
Items to be checked  
No image  
• Is the power supplied correctly?  
• Is the lens iris adjusted correctly?  
• Are the cables connected correctly?  
• Is the shutter mode set correctly?  
• Is the image process equipment set correctly?  
Poor color  
• Is the monitor adjusted correctly?  
• Is the white balance of the camera adjusted correctly?  
• Is the illumination dark?  
35  
 
Limited Warranty – TOSHIBA CCD Camera  
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties  
with regard to this CCD Camera ("Product"). These limited warranties extend to the Original End-User ("You[r]").  
One (1)Year Limited Warranty of Labor and Parts  
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of  
purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does not  
perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an ISD  
Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the Product to the  
ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.  
Instruction Manual (Owner’s Manual):  
You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this Product. Before seeking warranty  
service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and follow the instructions to  
correct the problem.  
Your Responsibilities  
This Limited Warranty is subject to the following conditions:  
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.  
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with  
specifications during the Limited Warranty period.  
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.  
4. You must pack the Product in its original carton using the original packing material, then insert the original carton  
containing the Product into another carton with additional packing material before shipping the Product to an ASP.  
DISCLAIMERS:  
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO  
NOT ALLOWTHE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY  
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TOYOU.  
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE  
REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT  
COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE  
PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY  
DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY  
OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER  
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT COMPANY, OR  
AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.  
SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES  
FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TOYOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY  
VARY FROM STATE TO STATE.  
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE,  
ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S  
WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR  
AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR  
SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT  
COVERED BY THIS LIMITED WARRANTY.  
How to Obtain Warranty Service – Step-By-Step Procedures:  
To obtain warranty service, You should:  
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.  
2. Arrange for shipment of the Product to an ASP.  
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem and a copy  
of the bill of sale or proof of purchase.  
4. Prepay all transportation and insurance costs.  
Questions? If you have any questions, please check ISD’s Web Site or send an e-mail as follows:  
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the  
terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce  
any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof,  
is hereby limited to one (1) year from the date You discover or should have discovered the problem. This limitation does not  
apply to implied warranties arising under state law. Some states do not permit limitation of the time within whichYou may bring  
an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives  
You specific legal rights and You may also have other rights which vary from state to state.  
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.  
Imaging Systems Division  
9740 Irvine Boulevard, Irvine, CA 92618-1697  
Copyright© 2007 Toshiba America, Inc. All rights reserved.  
 

Technicolor Thomson DVD Player D M51DVS User Manual
Telex Network Card NI 223 Plus User Manual
Toastmaster Oven TOV850B W User Manual
Toastmaster Range RA36C User Manual
VBrick Systems Server 4410 0118 0009 User Manual
Vermont Casting Outdoor Fireplace RAD VTBB User Manual
ViewSonic Laser Pointer WPG 350 User Manual
VTech Games Letter Engine User Manual
Waves Stereo Receiver L3 16 User Manual
Weed Eater Blower 530163349 User Manual