Toshiba Air Conditioner TCB BC1602UUL User Manual

AIR-DISCHARGE DIRECTION KIT FOR AIR CONDITIONER (SPLIT TYPE)

Installation Manual

Air-Discharge Direction Kit

(for 4-way air discharge cassette Type)

Model name:

Air-discharge direction kit

TCB-BC1602UUL

Installation Manual

Air-discharge direction kit

English

Manuel du proprietaire

Climatiseur ^{(Type à deux éléments)}

Français

Installation Manual

Air-dischage direction kit

3 INSTALLATION METHODS

CAUTION

• Before installing the wind shield, change the air conditioner settings. Refer to “Changing the setting” on page 4.

• Unless the setting is changed, the air blow temperature becomes low. This may cause the dew condensation.

„Installing the wind shield(s) and packings

• Attach the wind shields to the air flow openings (made of styrene foam) of the indoor unit and place the packings

on them to block the air flow. (Refer to Fig. 1 to 3.)

• Put the packings bending along the edges of the indoor unit external surface without blocking the concaved

portions of the drain pans. (If the packings are not put bending along the edge of the indoor unit external surface,

the dew condensation may occur.) (Refer to Fig. 1 and 3.)

* The size adjustment is required for the packing which are attached on the wind shield C. Cut 1.58” (40 mm) to

adjust its size in 16.5” x 4.3” (420 mm x 110 mm).

(Fig. 1)

(Fig. 2)

Packing

Packing Wind shield (A, B, C) Drain pan

Wind shield A

Packing

Indoor

unit

External

surface

(requiredtocut

1.58” (40 mm.)

Packing

Wind shield B

Wind shield C

Interior styrene foam

Air flow outlet

Drain piping

(Fig. 3)

Putthepackingswithout

blocking the concaved

portions.

Refrigerant piping

2-EN

– 2 –

Installation Manual

Air-dischage direction kit

„Installing the indoor unit

• Install the indoor unit (Install the indoor unit following the instructions described on the installation manual of the

indoor unit.)

• Block the air flow outlets following the air flow blocking pattern shown in the table below when controlling 3-way

or 2-way air flow.

• The blockage portions of the air flow outlet are specified depending on the models. Do not specify the blockage

of the airflow outlet other than specified in the table below.

Limited models only

Wind shield A

3-way air flow

Wind shield C

Available only for

SP180 to SP240.

Available only for

SP300 to SP420.

Available for all models

Wind shield A

2-way air flow

Wind shield C

Available for all models

3-EN

– 3 –

Installation Manual

Air-dischage direction kit

„Changing the setting

• The setting is changed by using a wired remote controller. (For the details, Refer to “Changing procedure”

described below.)

• Perform “„Setting the louver lock (Louver position fixing)”.

CAUTION

When the ceiling is higher than the specification, the fan control is required. So, in that case, perform the “high ceiling

setting” other than the setting described below.

The setting should be performed according to the instructions described on the installation manual attached to the

indoor unit.

“Changing procedure”: Change the setting while the device stops.

Push

sec.

buttons simultaneously for more than 4

The unit No. displayed at first shows the indoor unit address of the

header unit in group control operation. The fan operation of the

indoor unit (header unit), selected at this time, is carried out.

Every time when UNIT

in the group cotrol operation are displayed in order.

(Left button) is pushed, the No.

The fan operation of the indoor unit, selected at this time, is carried

out.

Set the CODE No.

by using the TEMP.

button.

Set the setting data by pushing TIME

TIME setting.

buttons for the

3-way air flow......................

3 6

2-way air flow......................

Push the

data are displayed.)

When changing the setting of other indoor unit in the group control

operation, return to 2.

button. (The setting completes if the setting

Pushing the

button enters to the normal stop status.

4-EN

– 4 –

Installation Manual

Air-dischage direction kit

„Setting the louver lock (Louver position fixing)

• Fix the louver at the air flow blockage portions. (For the setting methods, follow the procedures below.)

Push the LOUVER

4 seconds while the air conditioner is stopped.

The blinks.

(Right button) for more than

Unit No.

1-2

Unit No.

1-1

Unit No.

1-4

Unit No.

1-3

Push the UNIT

unit you want to set.

Every time you push the button, the Unit No. changes.

The fan of the selected indoor unit starts its operation and the

louvers swing.

(Left button) to select the indoor

Push the TEMP.

louver No. with the wind shield applied.

The selected louver starts to swing.

buttons to display the

Select the code 0001 by pushing the TIME

buttons.

Louver fixing position code

Electric parts box

Louver No.

Push the

After the setting contents is defined, the

(Return to step 3 if there are other two wind shields.)

button to define the setting contents.

mark lights.

Refrigerant piping

Push the button to exit the setting.

“F1” is displayed in the CODE No. on the remote controller

display.

This means that the 01 louver shown on the illustration is

Drain piping

selected.

(Louver No. diagram)

„Confirming the installation

• After the installation completes, perform the test run to confirm that no abnormality is found.

• For your future reference, please keep the installation manual on your side.

5-EN

– 5 –

Installation Manual

Air-dischage direction kit

MEMO

.....................................................................................................................

– 6 –

EH99678401

Technicolor Thomson TV DVD Combo TV DVD User Manual
Tekkeon Cell Phone Accessories MP1200 User Manual
Telstrat Cordless Telephone 7300 User Manual
Texas Instruments Stereo Amplifier TPA2012D2 User Manual
Thermador Gas Grill PB30ZS User Manual
Toshiba Security Camera IK WD05A User Manual
Tripp Lite Switch WEXT5 B060 032 User Manual
Uniden Answering Machine WDECT2385 User Manual
Univex Headphones AM327411 User Manual
Wacom Laptop DTU 1631 User Manual