The Swan Corporation Indoor Furnishings KSEU 3020 User Manual

KITCHEN SINK Model No. KSEU-3020  
OWNER’S MANUAL  
MODEL NO.  
CAUTION:  
Read ALL instructions carefully  
BEFORE starting your installation.  
Save this manual for future reference.  
Installation  
Care and  
Cleaning  
KSEU-3020  
Patent Pending  
 
Installation • Care and Cleaning  
CUT INSIDE OF LINE  
DRILL STARTER HOLE  
INSIDE OF CUTOUT  
LINE  
3. Drill starter hole inside of cutout line.  
4. Using a saber saw, cut inside of cutout line. Trial fit sink to  
check proper fit.  
IMPORTANT  
The Euro Style sink design allows for  
the drainboard to be located on either  
the left or right side. After you decide  
on the location of the drainboard, the  
fixture holes can then be located.  
NOTE  
Drill Starter Hole From Bottom  
Finish Drilling Hole From Top  
5. Fixture hole locations are identified with a gray label indicating  
the most desired placement. Drill starter hole from reverse side.  
Working from the top side as illustrated, position a hole saw on  
the starter hole and drill to complete the fixture hole. Clean out  
fixture hole with a knife or file. (See Caution). Attach faucet,  
drain, and accessories according to manufacturer’s instructions.  
6. Attach sink clips as illustrated to underside of sink. Sink clips  
provided will accommodate a counter top up to 1-1/2Љ (38mm)  
thick.  
CAUTION  
Use of a hole saw is preferred, however, if punch is used, insure  
that ledge is supported and punch is placed directly in middle of  
knock-out area. If hole is not used, peel off the label.  
 
KITCHEN SINK Model No. KSEU-3020  
Installation • Care and Cleaning  
APPLY  
CAULK  
7. Apply a bead of caulk (not included) to the underside of the  
sink flange and position sink into counter top opening. First,  
tighten screws in front, then tighten rear screws.  
8. Connect all faucet supply lines, disposal (if available), and  
drain trap fittings per manufacturer instructions.  
CHECK FOR LEAKS:  
• Supply user tubes to faucet  
• Supply riser tubes to shut off valves or lower connections  
• Fill sink with water and check for leaks around drain  
• Release water from sink and check for possible leaks  
• Tighten as needed  
CLEANING  
REPAIRING  
Solid Colors  
Clean your Swanstone kitchen sink as you would any other fine  
bath fixture, using normal household detergents and cleansers.  
Just wiping the wall surfaces quickly removes watermarks and  
residue. Occasional scrubbing with household abrasive cleansers  
ensures that the original luster is maintained, similar to tile and  
other permanent type bath fixture materials.  
Use 400 grit sandpaper to remove scratches and gouges in the  
surface. A “scotchbright pad” can be used to blend in the area.  
Aggregate Colors  
Use 400 grit sandpaper to remove scratches and gouges in the  
surface. To blend in the area use a fine grade, white, automotive  
polishing compound or paste wax.  
Patent Pending  
Form #400-1-94-10M  
 

Timex Watch 179 095006 NA User Manual
Toastmaster Toaster TMT2 User Manual
Topcon Inflatable Bouncy Toy FC 200 with Windows CE50 User Manual
Toshiba Computer Drive HDD2J95 User Manual
Toshiba Laptop A2 SP219 User Manual
Triarch Indoor Furnishings 29223 User Manual
Tricity Bendix Dishwasher BDW 10 User Manual
Tripp Lite Power Supply 120V Input Output User Manual
UMAX Technologies Scanner Mirage II User Manual
Vision Fitness Elliptical Trainer E3700HRT User Manual