1.0
Introduction/Features:
Altimeter w/cumulative assent/descent
Tech4o Alti-Ski Watch™
•
Owner's Manual
• Barometer
• Temperature
Content:
Altimeter Mode - Setting
Introduction/Features
• Ski Run Counter
• Time / date / alarm
Altimeter Mode - Max Altitude
11.3
11.4
11.5
12.0
12.1
12.2
12.3
13.0
To make the most of your purchase, be sure to carefully read this
manual and follow the included flow chart. Keep them safe for
future reference. Please follow these precautions in using and
caring for your new Tech4o Alti-Ski Watch:
• Avoid exposing the watch to extreme conditions
• Avoid rough use and/or severe impacts
• Occasionally clean the watch with a soft and moistened cloth
• Store the watch in a clean, dry place when not in use for an
extended period of time.
Ascent Mode - Max Rate of Ascent
Ascent Mode - Total Daily Ascent
Ascent Mode - Total Lifetime Ascent
Run Counter - Display
Run Counter - Trip Run Counter
Run Counter - Daily Run Counter
Run Counter - Lifetime Run Counter
Limited Warranty
2
3
TEMPERATURE
1.1 Button Functions On/Off
Mode Button: [M]
Used to select among the main modes of the
watch
ALTIMIETER
TIME
Button: [o/o]
Used to confirm selections, start/stop the
stopwatch, and lock/unlock altitude
Set/+ Button: [s/+]
RUN
DESCENT
Used to access setting mode and increase/
change digits during setting display. Also sets
intermediate/lap times in stopwatch mode
ASCENT
Option/- Button: [o/-]
Used to decrease/change digits during setting display and browse
through sub-functions
2.0 Time / Date Mode - Display
When Time / Date mode is selected, the
watch will display the current time
on the top row and the current date,
temperature, or ski run counter on the
bottom row.
Light Button: [L]
Used to illuminate the watch face for use during low light conditions
• To view time mode, press the [m] button
until the mode indicator displays the
clock symbol.
1.2 Major Function Modes
Press any button to wake the watch from sleep mode. Press the [M]
button to toggle among the main function modes.
4
5
2.1 Time / Date Mode - Setting
3.0 Daily Alarm Mode - Display
This watch includes a daily alarm. When the daily alarm is ON, the
alarm will sound for 30 seconds at the
alarm time every day.
• To view the daily alarm display, press
the [o/-] button once while in time/date
mode.
• In Time / Date mode press and hold the Set/+ button [s/+] for
two seconds.
• The 12 H / 24 H will flash. Use the [o/-] button to select between
a 12 or 24 hour clock feature. Press the [o/o] button to confirm
selection.
• The hours will flash. Use the [s/+] and [o/-] buttons to select the
correct hour. Press the [o/o] button to confirm selection.
• The minutes will flash. Use the [s/+] and [o/-] buttons to select
the correct minutes. Press the [o/o] button to confirm selection.
• The month will flash. Use the [s/+] and [o/-] buttons to select the
correct month. Press the [o/o] button to confirm selection.
• The days will flash. Use the [s/+] and [o/-] buttons to select the
correct day. Press the [o/o] button to confirm selection.
• The year will flash. Use the [s/+] and [o/-] buttons to select the
correct year. Press the [o/o] button to confirm selection.
• You have now completed the Date / Time Mode quick set.
• When the daily alarm is selected, the
watch will display the alarm setting
indicator in the top row and the daily
alarm time in the bottom row.
3.1 Daily Alarm Mode - Setting
• To set the daily alarm, press and hold the [s/+] button for 2
seconds. The hours will flash.
• Use the [s/+] and [o/-] buttons to adjust the hours. Press the [o/o]
button to confirm selection.
• At this time, the minutes will flash.
• Use the [s/+] and [o/-] buttons to adjust the minutes. Press the
[o/o] button to confirm selection.
• Press the [o/o] button again to set the alarm for on or off.
continues
6
7
Press the [o/-] button to confirm selection and advance to the
countdown timer mode.
4.2 Countdown Timer Mode
Using the Countdown Timer
4.0 Countdown Timer Mode - Display
• When in countdown timer mode, press the [o/o] button to
start the countdown.
This watch includes a countdown timer.
• To view the countdown timer, press the
[o/-] button twice while in time/date
mode.
• When the countdown timer is selected,
the watch will display the countdown
time in the top row and the current home
time in the bottom row.
• Press the [o/o] button again to stop the countdown.
• Press the [o/o] button again to resume the countdown
• When the countdown timer expires the alarm will sound for
30 seconds and the timer will reset to the last countdown
timer setting.
• Press the [o/-] button to proceed to the Stopwatch Mode.
5.0 Stopwatch Mode - Display
4.1 Countdown Timer Mode - Setting
This watch features 5 individual
stopwatch counters.
• To set the countdown timer, press and hold the [s/+] button for 2
seconds. The hours will flash.
• Use the [s/+] and [o/-] buttons to adjust the hours. Press the [o/o]
button to confirm selection.
• At this time, the minutes will flash.
• Use the [s/+] and [o/-] buttons to adjust the minutes. Press the
[o/o] button to confirm selection.
• Use the [s/+] and [o/-] buttons to adjust the seconds. Press the
[o/o] button to confirm selection and finish.
• The measuring unit of the stopwatch
is 1/100 seconds for the first 59
minutes, 59.99 seconds. After
reaching 1 hour of cumulative time,
the measuring unit changes to 1
second and the measuring range is 99
hours, 59 minutes, 59 seconds
continues
8
9
• Press the [o/o] button again to stop the stopwatch. The top and
bottom rows will now display current stopwatch time.
• Press the [o/o] button again to resume the stopwatch. The top row
will now display ------------- and the bottom row will display the
current stopwatch time.
• To view the stopwatch, press the [o/-] button three times while in
date/time mode.
• When the stopwatch is selected, the watch will display StP 1 in the
top row and 0:00 in the bottom row.
5.1 Stopwatch Mode - Setting
• While the stopwatch is running, you may enter LAP/INT times by
pressing the [s/+] button. The top row will display the first LAP/
INT time and the bottom row will display the cumulative stopwatch
time.
• After each successive LAP/INT time is entered, the top row will
display:
• In stopwatch mode, press and hold the [s/+] button for two
seconds.
• The LAP/INT indicator will flash.
• Both LAP and intermediate settings will record time the same way,
but the way the information is displayed will vary. The LAP setting
will show the last lap time when the [s/+] or [o/o] buttons are
pushed and in stopwatch history mode. The Intermediate setting
will show the cumulative intermediate times when the [s/+] or
[o/o] buttons are pushed and in stopwatch history mode.
• Use the [o/-] button to select between LAP and int settings. Press
the [o/o] button to confirm selection.
* the cumulative time of all the entered intermediate times
if the int setting was selected; or
* the last lap time if the lap setting was selected.
• The bottom row will display the cumulative stopwatch time.
• When the stopwatch is stopped, press the [o/-] button to proceed
to the stopwatch history mode or press [s/+] to proceed to the
next available stopwatch to begin recording another set of times
following the steps above. Note: there are 5 available stopwatches.
More stopwatch information can be recorded by clearing
stopwatch data in the stopwatch history mode or by recording
over stopwatch #5.
5.2 Stopwatch Mode - Using the Stopwatch
How to use the Stopwatch
• When in stopwatch mode, press the [o/o] button to start the
stopwatch. The top row will now display ------------- and the
bottom row will display the current stopwatch time.
10
11
6.0 Stopwatch History Mode - Display
7.0 Alternate Time Zone Mode - Display
When the stopwatch history mode is
selected the watch will display St HSt on
the top row and the current home time
on the bottom row depending on your
selection made in temperature mode.
• To access the stopwatch history mode,
press the [o/-] button 4 times while in
time/date mode.
When the alternate time zone mode is
selected the watch will display TIME 2
and the alternate time zone time in the
top row and the home time mode in the
bottom row.
• To view the alternate time zone display,
press the [o/-] button 5 times while in
time/date mode.
6.1 Stopwatch History Mode - Navigating Data
7.1 Alternate Time Zone Mode - Setting
How to retrieve saved stopwatch information:
• In the alternate time zone mode, press and hold the Set/+ button
[s/+] for two seconds.
• To view saved stopwatch information, press the [o/o] button in
stopwatch history mode to view the desired history log
• Press the [o/-] button to confirm selection and view the desired
data.
• Continue pressing the [o/-] button to scroll through the different
LAP/INT times for that stopwatch log
• The hours will flash. Use the [s/+] and [o/-] buttons to select the
correct hour, making sure to account for a.m. A, or p.m. P.
• Press the [o/o] button to confirm selection.
• The minutes will flash. Use the [s/+] and [o/-] buttons to select
the correct minutes.
• Press [o/o] button at any time to view a different stopwatch log.
• To clear all saved stopwatch data, press and hold the [s/+] button
while selecting a stopwatch log to view.
• Press the [o/o] button to confirm your selection.
• The alternate time zone is now set. Press the [o/-] to home time
display.
12
13
8.0 Temperature Mode - Display
maximum temperature reading since the setting was last reset.
• Press the [o/-] button again to access the minimum temperature
reading since the setting was last reset.
• Both maximum and minimum temperature readings can be reset by
pressing and holding the [s/+] button for 2 seconds while viewing
either the maximum or minimum records respectively.
• Surrounding temperatures are generally 10 - 15˚F / 5 - 8˚C
cooler than watch readings due to the effects of the wearer's body
temperature.
• To view temperature mode, press the [m]
button until the mode indicator displays T.
• In temperature mode the watch will
display temperatures in the top row and
home time, temperature, or run counter
in the bottom row.
8.1 Temperature Mode - Setting
• For more accurate readings, remove the watch from your wrist and
allow 5-10 minutes for sensors to adjust.
• In temperature mode, press and hold the
[s/+] button for 2 seconds. The ˚F or ˚C indicator will flash.
• Press the [o/-] button to select between ˚F or ˚C.
• Press the [o/o] button to confirm selection.
9.0 Altimeter Mode - Display
In altitude mode the watch will display
altitude and barometric measurements
in the top row and the current home
time, current temperature, or run counter
depending our your personal selection.
• At this time the bottom row will flash.
• Press the [o/-] button to select between home time, temperature,
or run counter to be displayed in the bottom row. Press the [o/o]
button to confirm selection.
8.2 Temperature Mode - Temperature Features
•
To view Altimeter Mode, press the
[m] button until the mode indicator
displays A.
Current, Maximum, and Minimum Temperatures:
• In temperature mode, press the [o/-] button to access the
14
15
9.1 Altimeter Mode - Setting
9.3 Altimeter Mode - Barometric Pressure
• In altimeter mode, press and hold the [s/+] button for 2 seconds.
• The current altitude reading will flash.
• In altimeter mode, press the [0/-] button to view the current
barometric pressure.
• Using the [s/+] and [o/-] buttons, enter your reference altitude.
Your reference altitude should be obtained from a reliable map
source for your current altitude.
• To change the unit of measure, press and hold the [s/+] button for
2 seconds.
• The inHG / mbar indicator will flash.
• Once you have researched and entered your reference altitude,
press the [o/o] button to confirm selection.
• Use the [o/-] button to select your desired unit of measurement.
Press the [o/o] button to confirm your selection.
• The ft/m indicator will now flash.
• Press the [o/-] button to select your desired unit of measurement.
Press the [o/o] button to confirm selection.
• Altimeter mode also has an optional lock feature.
• Press the [o/o] button to lock altimeter mode and prevent any
accidental recordings of changes in altitude.
10.0 Descent Mode - Display
In descent mode, the watch will display
altitude descent measurements on the
top row and the current home time,
current temperature, or the run counter
on the second row depending on your
personal preference.
9.2 Altimeter Mode - Maximum Altitude
• In altimeter mode, press the [o/-] button to view the maximum
altitude.
• The maximum altitude is the highest altitude recorded since the
feature was last reset.
• To view descent mode, press the [m]
button until the mode indicator displays
the down arrow.
• To reset the maximum altitude, press and hold the [s/+] button for
2 seconds.
16
17
10.1 Descent Mode - Trip Descent
10.5 Descent Mode - Total Lifetime Descent
• In descent mode, the default view is the total trip descent view.
• To clear/reset the total trip descent, press and hold the [s/+]
button for 2 seconds.
• In descent mode, press the [o/-] button 4 times to view the total
lifetime descent.
• To clear/reset the total lifetime descent, press and hold the [s/+]
button for 2 seconds.
10.2 Descent Mode - Rate of Descent
11.0 Ascent Mode - Display
• In descent mode, press the [o/-] button once to view the current
rate of descent.
• To clear/reset the current rate of descent, press and hold the
[s/+] button for 2 seconds. Note that the current rate of descent
automatically recalculates every minute also.
In ascent mode, the watch will display the
total trip ascent on the top row and the
current home time, current temperature,
or the run counter on the second row
depending on your personal preference.
10.3 Descent Mode - Maximum Rate of Descent
•
To view ascent mode, press the [m] button
until the mode indicator displays the up
arrow.
• In descent mode, press the [o/-] button twice to view the maximum
rate of descent for the trip.
• To clear/reset the maximum rate of descent, press and hold the
[s/+] button for 2 seconds.
11.1 Ascent Mode - Trip Ascent
• In ascent mode, the default view is the total trip ascent view.
• To clear/reset the current rate of ascent, press and hold the [s/+]
button for 2 seconds.
10.4 Descent Mode - Total Daily Descent
• In descent mode, press the [o/-] button 3 times to view the total
daily descent.
• The total daily descent is automatically reset at midnight.
18
19
11.2 Ascent Mode - Rate of Ascent
12.0 Run Counter - Display
• In ascent mode, press the [o/-] button once to view the current rate
of ascent.
• To clear/reset the current rate of ascent, press and hold the [s/+]
button for 2 seconds.
To view the run counter press the [m]
button until the mode indicator displays R.
• In run counter mode the watch will
display run information in the top row
and the current home time on the
second row.
• A run is calculated based on altitude
adjustment. An additional run is added
to the total when a period of descent is
followed by an ascent greater than 60ft.
or 20m.
11.3 Ascent Mode - Maximum Rate of Ascent
• In ascent mode, press the [o/-] button twice to view the maximum
rate of ascent for the trip.
• To clear/reset the maximum rate of ascent, press and hold the [s/
+] button for 2 seconds.
11.4 Ascent Mode - Total Daily Ascent
12.1 Run Counter - Trip Run Counter
• In ascent mode, press the [o/-] button 3 times to view the total
daily ascent.
• The total daily ascent is automatically reset at midnight.
• In the run counter mode, the default view is the trip run counter.
• A run is calculated based on altitude adjustment. An additional run
is added to the total if there is an ascent measured of more than
60ft. or 20m.
• To reset the total run counter, press and hold the [s/+] button for
2 seconds.
11.5 Ascent Mode - Total Lifetime Ascent
• In ascent mode, press the [o/-] button 4 times to view the total
lifetime ascent.
• To clear/reset the total lifetime ascent, press and hold the [s/+]
button for 2 seconds.
continues
20
21
What is not covered? Normal wear, and damage due to the abrasion, melting,
misuse, alteration, and abuse (including any disassembly) are not covered by
this warranty. Digital Watches are water resistant, they are not waterproof.
Damage resulting from excessive exposure to water, heat or cold is not covered
under this warranty. Additionally, the battery is not covered under the warranty.
Always have the battery replaced by an authorized repair center or jewler.
Should you do the work yourself, you will void this warranty.
12.2 Run Counter - Daily Run Counter
• To view daily run counter, press the [o/-] button. The total number
of runs for the day will be displayed.
• A run is calculated based on altitude adjustment. An additional run
is added to the total when a period of descent is followed by an
ascent greater than 60ft. or 20m.
How to obtain warranty service or repair of your watch: Should a defect covered
by this warranty appear in your watch, call our Consumer Service Department
toll-free at 1.800.572.8822 for return authorization and instructions. (You must
pay the cost of returning the unit to us). If the product is found to be defective
in material or workmanship, we shall, at our option, either repair or replace it
without charge, and will pay the cost of return shipment to you. If repairs are
required to correct any problem not covered by this warranty, we will contact
you for approval to proceed and to charge you for the components repaired or
replaced, plus a nominal charge for labor.
THERE ARE NO EXPRESS WARRANTIES ON YOUR WATCH THAT ARE NOT
CONTAINED IN THIS DOCUMENT. IN NO EVENT SHALL WE BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM USING OR
LOSS OF USE OF YOUR WATCH.
• The daily run counter is automatically reset at midnight.
12.3 Run Counter - Lifetime Run Counter
• To view the lifetime run counter, press the [o/-] button. The lifetime
number of runs for the watch will be displayed.
• A run is calculated based on altitude adjustment. An additional run
is added to the total when a period of descent is followed by an
ascent greater than 60ft. or 20m.
• To reset/clear the lifetime run counter, press and hold the [s/+]
button for 2 seconds.
13.0 Limited Warranty:
What is covered? Johnson Outdoors Inc. warrants your Tech4o Watch to be
free from defects in materials or workmanship, and to perform accurately, for
one (1) year provided it has not been damaged by the causes described in the
next paragraph.
Some states do not allow exclusion or limitation of incidental or consequential
damages, so the above exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights
which vary from state to state.
22
23
|