Symphonic TV VCR Combo SC309E User Manual

OWNER’S  
MANUAL  
9-INCH COLOR TV/VCR  
SC309E  
This Owner’s Manual is made of  
recycled paper.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR®  
is a U.S. registered mark.  
If you need additional assistance for set-up or operating after  
reading owner’s manual, please call TOLL FREE : 1-800-242-7158.  
Or visit our WEB SITE at http://www.funai-corp.com  
Please read before using this equipment  
 
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
19.Damage Requiring Service-Unplug this TV/VCR from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR.  
c. If the TV/VCR has been exposed to rain or water.  
d. If the TV/VCR does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/VCR to its normal operation.  
14.Lightning-For added protection for this TV/VCR receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/VCR due to lightning and  
power-line surges.  
e. If the TV/VCR has been dropped or damaged in any way.  
f. When the TV/VCR exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/VCR, ask the service technician to perform routine  
safety checks to determine that the TV/VCR is in proper  
operating condition.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/VCR.  
22.Heat-This TV/VCR product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18.Servicing-Do not attempt to service this TV/VCR yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to quali-  
fied service personnel.  
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
- 3 -  
EN  
9J27  
 
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LOCATION  
For safe operation and satisfactory performance of  
your TV/VCR, keep the following in mind when  
selecting a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top and bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Unauthorized recording or use of broadcast televi-  
sion programming, video tape, film or other copy-  
righted material may violate applicable copyright  
laws. We assume no responsibility for the unautho-  
rized duplication, use, or other acts which infringe  
upon the rights of copyright owners.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR near strong magnetic fields.  
Avoid moving TV/VCR to locations where temper-  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
ature differences are extreme.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR cassette holder.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a tape is played in a TV/VCR  
which has moisture, it may damage the tape and  
TV/VCR. Therefore when the condensation occurs  
inside the unit, turn the POWER button on and allow  
at least 2 hours for the unit to dry out.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 4 -  
EN  
9J27  
 
TABLE OF CONTENTS  
NORMAL RECORDING . . . . . . . . . . . . . . . . .19  
SKIPPING UNWANTED SCENES DURING  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19  
OTR (One Touch Recording) . . . . . . . . . . . . . .19  
TIMER RECORDING . . . . . . . . . . . . . . . . . . .20  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .22  
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .22  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .23  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6  
C OPERATING CONTROLS AND FUNCTIONS 7  
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11  
SELECTING THE LANGUAGE . . . . . . . . . . .11  
CLOCK SET UP (AUTO / MANUAL) . . . . . .11  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13  
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . .14  
DELETING (OR ADDING) CHANNEL . . . . .14  
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .23  
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .24  
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .24  
REAL TIME TAPE COUNTER . . . . . . . . . . . .24  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .24  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15  
WATCHING A TV PROGRAM . . . . . . . . . . . .15  
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .15  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .24  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .25  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .26  
C CABLE CHANNEL DESIGNATIONS . . . . . .26  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .16  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .16  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .16  
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .17  
NOISE CANCEL (in the Still mode) . . . . . . . .18  
VERTICAL HOLD CONTROL . . . . . . . . . . . .18  
TRACKING ADJUSTMENT . . . . . . . . . . . . . .18  
RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .18  
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .18  
INDICE  
CONTROLES DE OPERACIÓN Y  
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .27  
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30  
SELECCION DE IDIOMA . . . . . . . . . . . . . . . . .30  
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . .31  
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31  
CONEXIONES DE ANTENA/CABLE . . . . . . . .29  
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
- 5 -  
EN  
9J27  
 
FEATURES  
Infrared remote control  
Trilingual on screen menu display selectable in  
English, Spanish or French  
Still–“Freeze” the picture at any time, for close viewing  
of a particular scene. Only tapes recorded in SLP mode  
will show a fairly clear picture.  
Digital Auto Tracking (DTR)–Automatically adjusts the  
tracking for each tape you play.  
Rental play mode–Improves playback picture quality  
from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a tape  
indefinitely without pressing the PLAY button.  
Time search–Let you set the TV/VCR to advance the  
tape by entering the desired playback time you want to  
skip.  
OTR (One Touch Recording)–Instant timed recording  
from 30 to 480 minutes is possible at the push of the  
REC/OTR button.  
1 Year, 8 events (including Daily and Weekly Timer  
Recording)–The built-in timer allows you to record up  
to 8 programs at different times on different channels up  
to 1 year in advance. The Daily timer allows recordings  
to be made of daily broadcasts, and the Weekly timer  
allows recording to be made once a week up to the end  
of the tape.  
Auto return–After timer recording is finished, the  
TV/VCR can return to the beginning of the recording.  
Wake up/Sleep timer–Allows you to have the TV/VCR  
automatically turn on or off at a desired time.  
Timer Program Extension–Allow you to shift the time  
schedule for automatic timer recording.  
Two- way power–Allows you to power the TV/VCR  
with standard household AC or your vehicle’s battery,  
using the supplied car-battery cord.  
Real time counter–This shows the elapsed recording or  
playback time in hours, minutes, and seconds. The “–”  
indication will appear when the tape is rewound further  
than the tape counter position “0:00:00”.  
181 channel capability PLL frequency synthesizer  
tuner with direct station call–(A converter may be nec-  
essary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock function  
from a PBS broadcast station.  
Game mode–Automatically sets external input mode and  
allows TV/VCR display to be suitable for use with TV  
games.  
Auto power on and off system–Automatically turns on  
the TV/VCR when you insert the cassette, turns off after  
auto-rewind, and ejects when the beginning of the tape is  
reached.  
Auto rewind when the end of a tape is reached–This  
function doesn’t occur when using timer recording.  
2 Step picture search operation–You can view a video  
program at a high speed or super high speed in either a  
forward or reverse direction in LP and SLP mode. For  
SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
Auto Head Cleaner–Automatically cleans video heads as  
you insert or remove a cassette.  
Zero Return–The tape returns to counter of 0:00:00 by  
rewinding or fast forwarding.  
SUPPLIED ACCESSORIES  
Dipole Antenna  
Matching Adapter  
(300ohm-75ohm)  
Remote Control Unit  
Car Battery Cord  
(1813641 or 1780258 or  
UCPGANTPK004)  
2 AA Batteries  
(0EMN00723 or  
0EMN01183)  
PART NO.  
(N0150UD or N0107UD)  
WPZ0202GA004  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
242-7158.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control. If you decide to use a universal remote control with this unit, please be aware  
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-  
versal remote control.  
- 6 -  
EN  
9J27  
 
OPERATING CONTROLS AND FUNCTIONS  
- TV/VCR FRONT PANEL -  
POWER  
STOP/EJECT  
REW  
PLAY  
F.FWD  
REC/OTR  
VOLUME  
CHANNEL  
VIDEO AUDIO  
EARPHONE  
REC  
1 2 3 4  
5 6 7 8 9 10 11  
12 13 14  
5 POWER button– Press to turn TV/VCR on and off.  
Press to activate timer recording.  
6 STOP button– Press to stop the tape motion.  
EJECT button– Press in the Stop mode to remove  
tape from TV/VCR.  
- REMOTE CONTROL -  
25  
6
WAKE-UP  
/SLEEP  
POWER  
EJECT  
L button–  
5
CHANNEL  
RETURN  
Press to select setting modes from the on screen  
menu.  
1
4
7
2
5
8
3
6
9
24  
Press to enter digits when setting program.  
15  
CHANNEL  
VOLUME  
(for example: setting clock or timer program)  
7 REW button– Press to rewind the tape, or to view  
the picture rapidly in reverse during playback  
mode. (Rewind Search)  
12  
0
+100  
MENU  
DISPLAY  
MUTE  
11  
16  
17  
7
s button–  
23  
8
Press to select a mode from a particular menu.  
PLAY  
(for example: LANGUAGE or USER’S SET UP)  
8 PLAY button– Press to begin playback.  
K button–  
9
REW  
F.FWD  
STOP  
6
SPEED PAUSE/STILL  
RECORD  
22  
21  
10  
18  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
9 F.FWD button– Press to rapidly advance the tape,  
or to view the picture rapidly in forward during  
playback mode. (Forward Search)  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
COUNTER  
RESET  
19  
20  
1 VIDEO input jack– Connect to the video output  
jack of your video camera or another VCR.  
2 AUDIO input jack– Connect to the audio output  
jack of your audio equipment, video camera or  
another VCR.  
B button–  
When setting program (for example: setting  
clock or timer program), press to determine your  
selection and proceed to the next step you want to  
input.  
3 RECORD indicator– Flashes during recording.  
Lights up in the Stand-by mode for Timer  
Recording.  
4 Remote Sensor Window– Receives the infrared  
signals from the remote control.  
Press to determine setting modes from on screen  
menu.  
Press to select a mode from a particular menu.  
(for example: LANGUAGE or USER’S SET UP)  
- 7 -  
EN  
9J27  
 
- REAR VIEW - [Fig.3]  
27  
26  
28  
10 REC(RECORD) button– Press for manual recording.  
OTR button– Activates One Touch Recording.  
(only on the TV/VCR)  
11 VOLUME X / Y buttons– Adjust the volume  
level.  
12 CHANNEL K / L buttons– Press to select the  
desired channels for viewing or recording.  
You may display the main menu on the TV screen  
by pressing repeatedly this button on the  
TV/VCR.  
18 SPEED button– Press to choose the desired  
recording speed:SP/SLP.  
19 T-PROG. CLEAR button– Press to cancel a setting  
of timer program. (See page 22.)  
COUNTER RESET button– Press to reset counter  
to 0:00:00.  
20 GAME button– Sets the game mode and external  
input mode at the same time. (See page 15.)  
21 TIME SEARCH button– Press to activate Time  
Search mode.  
TRACKING function– Press to minimize video  
‘noise’ (lines or dots on screen) during playback  
mode. (See page 18.)  
22 PAUSE/STILL button– Press to temporarily stop  
the tape during the recording or to view a still pic-  
ture during playback.  
13 EARPHONE jack– Connects to earphones (not  
supplied) for personal listening. The size of jack is  
1/8” monaural (3.5mm).  
23 MUTE button– Mutes the sound. Press it again to  
resume sound.  
24 CHANNEL RETURN button– Press to go back to  
the previously viewed channel. For example,  
pressing this button once will change channel dis-  
play from 3 (present channel) to 10 (previously  
viewed channel), and pressing it a second time  
will return from 10 to 3.  
25 WAKE-UP/SLEEP button– Sets the Wake up or  
Sleep Timer. (See pages 22 and 23.)  
26 ANT. terminal– Connect to an antenna or cable  
system.  
14 Cassette compartment  
15 Number buttons– Press to select desired channels  
for viewing or recording. To select channels from  
1 to 9, first press the 0 button and then 1 to 9.  
+100 button– When selecting cable channels  
which are higher than 99, press this button first,  
then press the last two digits. (To select channel  
125, first press the “+100” button then press “2”  
and “5”.)  
16 MENU button– Press to display the main menu on 27 DC 13.2V jack– Connect to the Car Battery Cord.  
the TV screen.  
28 Power cord– Connect to a standard AC outlet  
17 DISPLAY button– Display the counter or the cur-  
rent channel number and current time on the TV  
screen. (See page 24.)  
(120V/60Hz).  
- 8 -  
EN  
9J27  
 
PREPARATION FOR USE  
From Cable System or  
Satellite Dish  
Satellite Box or  
Dipole Antenna  
(Supplied)  
VHF/UHF Antenna  
(Not supplied)  
OUT  
Cable Box  
IN  
Flat twin-lead cable  
(Not supplied)  
VHF Antenna  
(Not supplied)  
Matching Adapter  
(Supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
or  
or  
VHF/UHF  
Combiner  
(Not supplied)  
or  
ANT.  
75-ohm Coaxial  
Cable (Not  
supplied)  
Flat twin-lead cable  
Fig.4  
or  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/VCR without a converter box.  
By using this connection you can:  
1) Use the TV/VCR remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
NOTE: This unit will ONLY record and view the  
same channel.  
ANTENNA/CABLE  
CONNECTIONS  
DIPOLE ANTENNA HOOK UP  
1. Push the stem of the Dipole Antenna (supplied)  
into the hole for antenna at the back of TV/VCR.  
2. Connect the flat twin-lead cable from the Dipole  
Antenna to the 300/75 ohm Matching Adapter  
(supplied).  
3. Plug the Matching Adapter to ANT terminal of  
TV/VCR as shown in drawing.  
For the best reception, extend the Dipole Antenna and  
adjust its length and position. (Avoid handling the top  
section when making adjustments.)  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown in drawing.  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR Remote Control. Unattended timer record-  
ing is limited to one channel at a time.  
NOTE: If it is difficult to get good reception with the  
indoor antenna, the use of an outdoor antenna is rec-  
ommended. Before an outdoor antenna is connected  
to the set, the indoor antenna should be disconnected.  
VHF/UHF COMBINED ANTENNA  
A VHF UHF 75 ohm combination antenna can be  
connected to ANT terminal.  
TO RECORD A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
1. Set the TV/VCR channel selector to the output channel  
of the Cable Converter Box or Satellite Box. (Ex. CH3)  
2.Select the channel to record from your Cable  
Converter Box or Satellite Box.  
VHF/UHF SEPARATE ANTENNAS  
In some areas it will be necessary to use an outdoor  
antenna.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
- 9 -  
EN  
9J27  
 
To the vehicle's  
cigarette-lighter socket  
INSTALLING THE BATTERIES  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
VHF/UHF Combination  
Mobile Antenna  
(Not supplied)  
Car battery cord  
(Supplied)  
3)Replace the cover.  
DC13.2V  
ANT.  
NOTES:  
Be sure your vehicle has a 13.2-volt (12-volt), neg-  
ative-ground electrical system.  
EXTERNAL INPUT MODE  
When using an external input signal (another VCR or  
video camera), connect the player’s audio/video out-  
put cables to the AUDIO IN/ VIDEO IN jacks of  
your TV/VCR. Then press the CHANNEL K or  
button until “AUX” appears on the screen.  
Be sure you use only the supplied car battery cord.  
Using another cord could damage the TV/VCR.  
Be sure the socket is free of ashes and other debris.  
Be sure to push the car battery cord’s plug com-  
pletely into the cigarette-lighter socket.  
Always unplug the car battery from the cigarette-  
lighter socket before you unplug it from the  
TV/VCR.  
L
AUX  
You must disconnect the car battery cord from the  
TV/VCR before you can use the AC power.  
Be sure to replace the fuse with only the same type,  
5A, 250V.  
Be sure the AC cord is wound as shown below.  
MOBILE CONNECTION  
WARNING:The driver should never watch  
the TV/VCR while operating a motor vehicle.  
CAUTION: If you use the TV/VCR with the  
vehicle’s engine off, recharge the vehicle’s  
battery after about every 4 hours of use to  
prevent it from running down. After you fin-  
ish using the TV/VCR be sure you unplug the  
car-battery cord from the cigarette-lighter  
socket.  
1) The supplied indoor antenna is adequate when  
your vehicle is stationary. For best reception on  
the road, use a high-quality VHF/UHF mobile TV  
antenna.  
2) Attach the car battery cord to the DC13.2V (12V)  
connector on the back of the TV/VCR. Then, con-  
nect the other end to your vehicle’s cigarette-  
lighter socket.  
- 10 -  
EN  
9J27  
 
SET UP FOR USE  
CLOCK SET UP  
SELECTING THE LANGUAGE  
(AUTO / MANUAL)  
1 Plug in the TV/VCR power cord  
Plug the TV/VCR power cord into a  
standard AC outlet.  
The TV/VCR clock must be set correctly before VCR  
timer recording is possible. It is suggested that the  
clock be set manually when first setting up the  
TV/VCR. Then, set to [ON] the auto clock setting  
which will periodically correct the setting if necessary.  
NOTE: If you cannot receive a station with time sig-  
nals, auto clock setting cannot be performed. Use  
manual setting only.  
NOTE:  
If some digits appear in the corner of  
the screen, press the POWER button  
without unplugging the power cord.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
MANUAL CLOCK SETTING  
Make sure ...  
The TV/VCR is turned on.  
In the example below, the clock is to be set to:  
DATE  
May 6th, 2004  
– M E N U –  
2 Select “LANGUAGE”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
TIME SEARCH  
SETTING TIME 5:40PM  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “LANGUAGE”.  
B
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
TIME SEARCH  
B
3 Select “ENGLISH”, “ESPAÑOLor  
“FRANÇAIS”  
Select “ENGLISH”, “ESPAÑOL”= Spanish or  
“FRANÇAIS”= French using the F.FWD/B or  
REW/s button.  
Press the PLAY/K or STOP/L  
button to point to “SETTING  
CLOCK”.  
Then, press the F.FWD/B button.  
2 Select “MANUAL CLOCK SET”  
Press the PLAY/K or STOP/L  
button to point to “MANUAL  
CLOCK SET”.  
– SETTING CLOCK –  
4 Exit the Language mode  
Press the MENU button on the remote control to  
return to TV mode.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[OFF]  
Then, press the F.FWD/B button.  
NOTE: If for some reason the menu is in Spanish or  
French, press the MENU button on the remote con-  
trol, press the PLAY/K button to point to “IDIOMA  
[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then  
press the F.FWD/B button, then press the MENU  
button on the remote control.  
3 Select the month  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
Press the PLAY/K or STOP/L but-  
ton until your desired month  
appears. (Example: May 05)  
Then, press the F.FWD/B button.  
0 5  
/
– – – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
4 Select the day  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
Press the PLAY/K or STOP/L but-  
ton until your desired day appears.  
(Example: 6th 06)  
0 5  
/
0 6 – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
- 11 -  
EN  
9J27  
 
system connection using the ANT. terminal on the  
rear of the TV/VCR.  
NOTE:  
If a cable converter box is being used, make sure it  
is powered on.  
You must use the TV/VCR remote control to per-  
form the clock setting procedure.  
If the TV/VCR is connected directly to a cable  
converter box or satellite box, the local PBS station  
must be selected on the cable box itself, and the  
TV/VCR must be set to the output channel of the  
cable converter box or satellite box (usually chan-  
nel 3 or 4), to be able to set up or correct the clock  
automatically.  
5 Select the year  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
Press the PLAY/K or STOP/L but-  
ton until your desired year appears.  
(Example: 2004)  
0 5  
/
0 6 THU 2 0 0 4  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
6 Select the hour  
Press the PLAY/K or STOP/L but-  
ton until your desired hour appears.  
(Example: 5, PM)  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
0 5  
/
0 6 THU 2 0 0 4  
HOUR  
0 5  
MINUTE  
– – PM  
:
Then, press the F.FWD/B button.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: 40)  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
0 5  
/
0 6 THU 2 0 0 4  
– M E N U –  
HOUR  
0 5  
MINUTE  
4 0 PM  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
TIME SEARCH  
:
B
Press the PLAY/K or STOP/L but-  
ton to select “SETTING CLOCK”.  
Press the F.FWD/B button to enter  
“SETTING CLOCK” menu.  
8 Start the clock  
Press the MENU button on the  
remote control.  
Although seconds are not dis-  
played, they begin counting from  
00 when you press the MENU but-  
ton on the remote control. Use this  
5:40 PM  
2 Set “AUTO CLOCK” to [ON]  
Press the F.FWD/B button until  
“AUTO CLOCK [ON]” appears.  
– SETTING CLOCK –  
B
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[OFF]  
feature to synchronize the clock with the correct  
time.  
NOTE:  
3 Begin “AUTO CLOCK CH SEARCH”  
When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
Press the STOP/L button to select  
– SETTING CLOCK –  
“AUTO CLOCK CH SEARCH”.  
Press the F.FWD/B button.  
The TV/VCR is now searching  
AUTO CLOCK  
[ON]  
B
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[OFF]  
TO CHANGE CLOCK SETTING  
If you want to change the clock,  
1)Follow steps [1] and [2].  
2)Select where you want to change using the  
F.FWD/B or REW/s button.  
3)Enter correct numbers using the PLAY/K or  
STOP/L button.  
for the station which contain the  
auto clock set signal. The search  
for a signal may take up to 20  
seconds per channel.  
– AUTO CLOCK CH SEARCH –  
08  
10  
13  
“_ _” appears at the lower left of  
the screen when the search has  
ended.  
_ _  
Auto Clock station- write down  
the number(s) that appear on the screen. These are  
the auto clock  
4)Press the MENU button on the remote control to  
start the clock.  
station(s) in your area. See item 4 below.  
If no number(s) appear on the TV screen, there are  
no stations in your area which contain the Auto  
Clock signal. Auto Clock Setting is not possible.  
Please use Manual Clock Setting on page 11.  
Press the MENU button to exit the screen.  
NOTE: During Auto Clock CH Search, the picture  
may be distorted. This is normal.  
PLEASE NOTE:  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and  
press the F.FWD/B or REW/s button to turn [OFF]  
this function. Then you can manually adjust the  
clock.  
AUTOMATIC CLOCK SETTING  
Make sure ...  
The TV/VCR is turned on.  
Confirm the TV/VCR is receiving a RF (Radio  
Frequency) signal from either an antenna or cable  
- 12 -  
EN  
9J27  
 
DAYLIGHT-SAVING TIME  
Select this feature and the TV/VCR’s clock automati-  
cally will advance one hour in April, then reverse one  
hour in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
First Sunday of April : At 2 AM the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
4 Enter the channel number that contains the  
Automatic Clock Setting Signal  
Press the MENU button on the  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
PICTURE CONTROL  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to select “SETTING CLOCK”.  
Press the F.FWD/B button to enter  
“SETTING CLOCK” menu.  
Press the STOP/L button to select  
“AUTO CLOCK CH”.  
Press the F.FWD/B or REW/s  
buttons until you locate Auto Clock  
Set station number. See item 3  
above.  
TIME SEARCH  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
B
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[
45]  
[OFF]  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
Press the MENU button to exit the screen.  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
5 Turn off the TV/VCR  
Once the TV/VCR is turned off , it will periodically  
check and set the correct date and time.  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
PICTURE CONTROL  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING  
CLOCK”.  
TIME SEARCH  
Then, press the F.FWD/B button.  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
Press the PLAY/K or STOP/L but-  
– SETTING CLOCK –  
ton to point to “D.S.T.”.  
Then, press the F.FWD/B or  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[ON]  
REW/s button until [ON] appears.  
3 Exit the Daylight-Saving Time mode  
Press the MENU button on the remote control to  
return to TV mode.  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
F.FWD/B or REW/s button. Then, press the MENU  
button to return to TV mode.  
- 13 -  
EN  
9J27  
 
DELETING (OR ADDING)  
CHANNEL  
CHANNEL SET UP  
You can program the tuner to scan all the channels  
you receive in your area.  
NOTE: Channel memory programming is NOT  
needed when connected to a cable box or satellite  
box. Just select the TV/VCR channel selector to the  
output channel of the cable box or satellite box (Ex  
CH3). Then select the channel to be viewed on the  
Cable Box or Satellite Box.  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
– M E N U –  
1 Select “CHANNEL SET UP”  
TIMER PROGRAMMING  
PICTURE CONTROL  
Press the MENU button on the  
SETTING CLOCK  
B
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
remote control. Then press the  
PLAY/K or STOP/L button to  
point to “CHANNEL SET UP”.  
Then, press the F.FWD/B button.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
TIME SEARCH  
1 Select “CHANNEL SET UP”  
2 Select “ADD/DELETE CH”  
Press the PLAY/K or STOP/L but-  
ton to point to “ADD/DELETE  
CH”.  
– CHANNEL SET UP –  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
B
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
TIME SEARCH  
Press the F.FWD/B button.  
Then, press the F.FWD/B button.  
3 Enter the desired channel number  
Press the PLAY/K or STOP/L but-  
ton until your desired channel num-  
ber appears. (You can also use the  
number buttons or the CHANNEL  
K/L button to enter it.) (Example:  
CH8)  
2 Begin auto ch programming  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO CH PRO-  
GRAMMING”.  
Then, press the F.FWD/B button.  
The tuner scans and memorizes all  
the active channels in your area.  
– CHANNEL SET UP –  
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
08  
B
ADD / DELETE  
4 Delete (or add) it from (into) memory  
Press the F.FWD/B or REW/s button. The channel  
number changes to light red. The channel is deleted  
from memory.  
3 After scanning  
The tuner stops on the lowest memorized channel.  
When AUTO CH PROGRAMMING is activated  
To delete another channel, repeat steps [3] and [4].  
If you press the F.FWD/B or REW/s button  
where there is no TV signal input, “NO TV SIG-  
NALS” will appear on the display after the com-  
pletion of the channel scanning.  
again, the channel is memorized again.  
The TV/VCR may recognize TV channels to be  
Added channel: Light blue.  
Deleted channel: Light red.  
CATV channels by the receiving conditions. In this  
case, try auto ch programming again in the fine  
receiving conditions.  
5 Exit the channel setup mode  
Press the MENU button on the remote control to  
returns to TV mode.  
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL K or L button.  
- 14 -  
EN  
9J27  
 
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
The TV/VCR’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a natural looking image.  
NOTES:  
1 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR.  
2 Select the channel number  
Press the CHANNEL K or L button to select your  
desired channel number or press the number buttons  
on the remote control.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be viewed must be selected  
on the cable box or satellite box.  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
Make sure ...  
TV/VCR power must be turned on.  
1 Select “PICTURE CONTROL”  
3 Adjust sound  
Press the VOLUME X or Y button  
to adjust the volume.  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
remote control.  
B
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to ”PICTURE CON-  
TROL”.  
VOLUME 20  
LANGUAGE [ENGLISH]  
ZERO RETURN  
TIME SEARCH  
C
C
C
C
C
C
C
C
C
C
C
C
Then, press the F.FWD/B button.  
GAME MODE  
2 Select item you want to adjust  
This function enables you to decrease the TV screen  
contrast and making it suitable for use with a TV  
GAME.  
Press the PLAY/K or STOP/L but-  
ton until desired control is dis-  
played.  
NOTE: This function CANNOT be set during recording.  
BRIGHT  
BRIGHT  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
CONTRAST  
COLOR  
TINT  
GAME  
Press the GAME button on the  
remote control. “GAME” appears  
on the screen.  
SHARPNESS  
When you press the GAME button;  
3 Adjust the picture control  
The TV/VCR comes on automatically if it is off.  
The TV/VCR will be in external input mode auto-  
matically.  
Press the F.FWD/B or REW/s button to adjust to  
your desired level.  
REW/s  
to decrease  
brightness  
to decrease  
contrast  
F.FWD/B  
to increase  
brightness  
to increase  
contrast  
TO CANCEL THE GAME MODE  
Press the GAME button or CHANNEL K or L but-  
ton on the remote control.  
BRIGHT  
CONTRAST  
DEGAUSSING  
Magnetism from nearby appliances might affect the  
color of the TV picture.  
COLOR  
TINT  
to pale  
to brilliant  
to purple  
to green  
to clear  
SHARPNESS to soft  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect  
power cord from AC outlet then reconnect it after 30  
minutes.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
- 15 -  
EN  
9J27  
 
PLAYBACK  
This TV/VCR will operate with any cassette that has the  
mark. For best results, we  
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
INSERTING A CASSETTE  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
AUTO REPEAT PLAYBACK  
The TV/VCR has the auto repeat function that allows  
you to repeat a tape indefinitely without touching the  
PLAY button.  
cassette until it is drawn into the TV/VCR. The  
TV/VCR will automatically turn on.  
Window  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part, which is blank for more than  
10 seconds.  
WRONG  
CORRECT  
PRECAUTIONS  
Avoid moisture. Moisture condensation may occur  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR, wait until the tape has warmed to  
room temperature and the moisture has evaporated.  
Avoid extreme heat, high humidity and magnetic  
fields.  
1 Select “USER’S SET UP”  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
CHANNEL SET UP  
B
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
TIME SEARCH  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
USER’S SET UP  
2 Select “ALLor “BLANK”  
Press the PLAY/K or STOP/L but-  
ton to point to “REPEAT PLAY”.  
Press the F.FWD/B or REW/s  
button repeatedly until your desired  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
NORMAL PLAYBACK  
Make sure ...  
selection [ALL] or [BLANK] appears.  
TV/VCR power must be turned on.  
3 Exit the Repeat Play setting  
Press the MENU button on the remote control to  
return to the TV mode.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR will start playback automatically.  
2 To begin playback  
4 Start playback  
B
PLAY  
Press the PLAY button.  
Press the PLAY button to start the Repeat Play.  
”REPEAT PLAY B” appears.  
Note: If any menu is activated on  
the screen, the PLAY button does  
not function. Press the MENU but-  
ton to clear the menu. then, press  
the PLAY button.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
3 To stop playback  
Press the STOP button when play-  
back is completed.  
STOP  
TO CANCEL THE REPEAT PLAY MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
- 16 -  
EN  
9J27  
 
NOTES:  
SEARCH  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
PICTURE SEARCH  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
This function will not operate in recording mode.  
In the example below: To watch a program after 2  
hour 50 minutes from the present position, in either  
direction.  
1)You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD or REW button during playback. (in the  
SP / LP / SLP modes)  
2)Press it again and the TV/VCR will now search in  
super high speed. (in the LP / SLP modes only)  
NOTE: Tapes recorded in the SP or LP mode will  
display a noise bar on the TV screen and the pic-  
ture may revert to Black and White. This is normal.  
3)Press the PLAY button to return to normal speed.  
1 Insert a tape.  
2 Select “TIME SEARCH” mode  
Press the TIME SEARCH button (with each push it  
will increase by 10 minute).  
3 Enter your desired time  
Press the PLAY/K or STOP/L but-  
TIME SEARCH  
2 : 50  
ton until your desired time appears.  
(Example: “2:50” stands for 2 hours  
50 minutes)  
If you wish to cancel the Time Search at this point,  
press the MENU button on the remote control.  
ZERO RETURN  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
NOTE:  
4 Begin Time Search  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
By pressing the REW/s or F.FWD/B button, the  
TV/VCR will rewind or fast forward to the specified  
point.  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point at which you want to review.  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
2 Reset the counter to 0:00:00  
Press the COUNTER RESET button repeatedly.  
TO CANCEL THE TIME SEARCH at this  
point  
Press the STOP/EJECT button on the TV/VCR or the  
remote control. This will delete the selected time.  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
Press the STOP button when recording or playback is  
completed.  
STILL PICTURE  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE/STILL  
button during playback. Only tapes recorded in the  
SLP mode will show the least amount of lines. Press  
the PLAY button to return to playback.  
NOTES:  
4 To activate “ZERO RETURN” mode  
Press the MENU button on the  
– M E N U –  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “ZERO RETURN”.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
B
ZERO RETURN  
TIME SEARCH  
Usually there will be video “noise” lines (black  
and white streaks or dots) on the screen. This is  
normal.  
Then, press the F.FWD/B button.  
The counter will appear on the TV  
screen.  
The tape will automatically stop when the counter  
returns to 0:00:00.  
If the tape was originally recorded in SP or LP  
mode, the still picture will be black and white in  
addition to the “noise” lines.  
This is not a fault of the machine, but is a by-  
product of the technology involved in producing  
a TV/VCR with 2 video heads.  
If it is left in the Still mode for more than five min-  
utes, the TV/VCR will automatically switch to the  
Stop mode.  
TIME SEARCH  
The Time Search function makes it possible to  
quickly advance the tape to your desired position  
simply by entering the exact amount of playback  
time you want to skip.  
- 17 -  
EN  
9J27  
 
NOISE CANCEL (in the Still mode)  
RENTAL PLAYBACK  
This feature allows you to reposition or reduce the  
noise lines of a still picture. Press the PAUSE/STILL  
button so that the noise lines change position on the  
screen so you can see the picture in its entirety with-  
out distracting noise lines.  
NOTE: This feature can be activated ONLY when  
viewing a tape recorded in the SLP mode. If the tape  
was originally recorded in the SP or LP mode, the  
still picture may revert to black and white in addition  
to the “noise bars”. This is normal.  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
1 Select “USER’S SET UP”  
Press the MENU button on the  
remote control.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
B
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
TIME SEARCH  
VERTICAL HOLD CONTROL  
USER’S SET UP  
2 Set “RENTALto [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “RENTAL”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
the CHANNEL K or L button.  
NOTE:  
If there are video noise lines on the screen, reposition  
or reduce them. Refer to “NOISE CANCEL”.  
3 Exit the Rental setting  
Press the MENU button on the remote control to  
return to the TV mode.  
TRACKING ADJUSTMENT  
4 Start playback  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the TV/VCR.  
However when playing pre-recorded tapes or tapes  
recorded on units other than your own, noise lines  
(black and white streaks) may appear on the play-  
back picture. If this occurs, you can adjust the  
tracking control manually by pressing the CHAN-  
NEL K or L button until the streaks disappear. To  
return to the DTR function, stop the tape once and  
start playback again.  
TO CANCEL THE RENTAL MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
RECORDING  
TWO DIFFERENT TAPE SPEEDS  
ERASE PREVENTION  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).  
The table below shows the maximum recording/play-  
back time using T60, T120 or T160 tapes in each  
mode.  
You can prevent accidental  
erasing of recording by  
breaking off the tab on the  
back edge of the cassette.  
Tab  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
If you decide to record on  
the tape again, cover the  
hole with plastic tape.  
T60  
1 hour  
3 hours  
T120  
T160  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
Note: You can play back a tape recorded in LP mode  
(Long Play).  
Plastic Tape  
- 18 -  
EN  
9J27  
 
Make sure ...  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to  
the point at which you want to begin recording.)  
NOTE: This unit will ONLY record and view the same channel.  
NORMAL RECORDING  
OTR (One Touch Recording)  
You can ONLY watch the same TV program that is  
being recorded.  
This function enables you to set a recording length  
simply by pressing the REC/OTR button on the  
TV/VCR.  
Make sure ...  
1 Select the channel to be recorded  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab  
Press the number buttons on the  
CH 10  
remote control or the CHANNEL  
K or L button.  
in place. (If necessary, rewind or fast forward the  
Remember: If the TV/VCR is con-  
nected to a cable box or satellite  
box, the TV/VCR must be on CH3  
or CH4, then the channel to be recorded must be  
selected on the cable box or satellite box.  
tape to the point at which you want to begin  
recording.)  
NOTES:  
This function CANNOT be done from the remote  
control.  
Recording starts immediately when the REC/OTR  
button is pressed.  
When the REC/OTR button is pressed 18 times, the  
TV/VCR returns to the Normal Recording mode.  
2 Select the tape speed  
Press the SPEED button to select  
the desired tape speed (SP/ SLP).  
To stop the OTR operation, press the STOP button  
on the TV/VCR or on the remote control.  
SP  
To show the remaining time, press the DISPLAY  
button on the remote control so that “OTR”  
appears on the TV screen. (It will show up momen-  
tarily then disappear.)  
REC  
3 Begin recording  
Press the RECORD button.  
Recording stops when 0:00 is reached.  
Please note that in the SLP mode maximum record-  
ing time, assuming the tape is started at the begin-  
ning, is 8 hours using T-160 (or 6 hours using T-120).  
SP  
4 Stop recording  
Press the STOP button when recording is completed.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, ejects the tape and turns itself off.  
If you press the power button during OTR, the  
TV/VCR continues recording until the selected  
length is reached.  
SKIPPING UNWANTED  
SCENES DURING RECORDING  
Press the PAUSE/STILL button to  
PAUSE  
temporarily stop recording.  
Press the PAUSE/STILL or  
RECORD button to resume record-  
ing.  
NOTES:  
1 Select the channel to be recorded  
Press the number buttons on the remote control or the  
CHANNEL K or L button.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
SP  
After five minutes, the TV/VCR will automatically  
switch to the Recording mode to prevent tape dam-  
age.  
2 Select the tape speed  
Press the SPEED button to select the desired tape  
speed (SP/ SLP).  
- 19 -  
EN  
9J27  
 
Avoid over lap of programs ...  
There is a chance that a program will not be record-  
ed. when programs overlap;  
3 Begin OTR  
OTR(2 : 30)  
Press the REC/OTR button on the  
TV/VCR as many times as needed.  
The recording length will be deter-  
mined by the number of times you  
press the REC/OTR button. Each  
The program with an earlier start has priority.  
Once the earliest program finishes, the overlapping  
programs will begin recording in sequence.  
SP  
The illustration below demonstrates the sequence  
of recordings.  
additional push will increase the recording time by  
30 minutes. It is set up to 8 hours.  
Recording Sequence  
Push(es) Display  
1 push  
Recording length  
(normal recording)  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
9:30AM-12:00PM  
2 pushes  
3 pushes  
0:30  
1:00  
30 minutes  
60 minutes  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
17 pushes  
8:00  
480 minutes  
1 Select “TIMER PROGRAMMING”  
Press the MENU button on the remote control.  
TIMER RECORDING  
Confirm “TIMER PROGRAM-  
MING” is pointed by pressing the  
PLAY/K button.  
– M E N U –  
B
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
TIME SEARCH  
You may set the TV/VCR to start and end a record-  
ing while you are away. You can set 8 programs to  
record on specific days, daily or weekly within a 1  
year period.  
In the example below, the timer is being set to record:  
July 5th, 2004  
SETTING TIME: from 7:30PM to 8:50PM  
And press the F.FWD/B button.  
If you have not yet set the clock,  
“MANUAL CLOCK SET” appears. If so, follow  
steps [3] to [8] on pages 11 and 12. Then set the  
timer recording.  
DATE:  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
2 Select your desired program position (1~8)  
– TIMER PROGRAMMING –  
Press the PLAY/K or STOP/L but-  
Make sure ...  
CH DATE  
BEGIN END  
ton to select the desired program  
position.  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
If a cable box or satellite box is connected with the  
TV/VCR you will be limited to record only one  
channel. And the channel selector on the TV/VCR  
must be selected to the output channel of the boxes  
CH 3 or CH 4 and then the actual channel to be  
recorded must be selected on the boxes.  
Clock must be set to the correct time and date  
before setting the timer.  
TV/VCR power must be turn on to program it.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
B
3 Set the channel number  
Press the PLAY/K or STOP/L but-  
ton until the desired channel num-  
ber appears.  
(Example: CH61)  
Then, press the F.FWD/B button.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
The channel you want to record is properly set in  
advance.  
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the PLAY/K (up) button  
until the desired date appears.  
(Example: “7/05” for July 5th).  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/05 MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
- 20 -  
EN  
9J27  
 
For every day recording : To record a TV program at  
the same time on the same channel every day.  
(Example: Monday through Sunday)  
10 Finish setting the program  
Press the F.FWD/B or REW/s button. The program  
is now completed.  
Press the STOP/L (down) button  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
until “EVRY DAY” appears.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
To set another program, repeat steps [2] to [10].  
Press the MENU button on the remote control to  
B
return to original mode.  
For weekly recording : To record a TV program at  
the same time on the same channel every week.  
(Example: every Monday)  
11 Set the timer  
Press the POWER button to set automatic timer  
recording. The TIMER REC indicator lights up.  
– TIMER PROGRAMMING –  
Press the STOP/L (down) button  
You must turn off the TV/VCR to activate automat-  
ic timer recording.  
CH DATE  
BEGIN END  
until “EVRY” and your desired  
day of the week appear together.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
5 Set beginning hour  
To shift the time schedule of an automatic timer  
recording.  
1)Press the POWER button.  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “ 7, PM” for 7:30PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 MON 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
2)Repeat step [1] on page 20.  
3)Press the RECORD button and select the desired  
program using the PLAY/K or STOP/L button.  
4)Press the RECORD button again.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press the  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
6 Set beginning minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: “30” for  
7:30PM)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
Then, press the F.FWD/B button.  
PAUSE/STILL button on the remote control. The  
recording time returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automati-  
cally be set to the SLP mode.  
5)Press the F.FWD/B or REW/s button to exit the  
setting menu. Then press the MENU button on the  
remote control to return to original mode.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
7 Set end hour  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30 - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
8 Set end minute  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: “50” for  
8:50PM)  
TO CORRECT A PROGRAM  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50 - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
While setting a program; press the REW/s but-  
ton to go back one step and enter the correct num-  
bers using the PLAY/K or STOP/L button.  
Then, press the F.FWD/B button.  
After setting a program;  
1)Press the POWER button.  
9 Set the tape speed  
Press the PLAY/K or STOP/L but-  
ton until the desired tape speed  
appears. (Example: SP)  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
2)Repeat steps [1] - [2] on page 20.  
3)Press the F.FWD/B button (or press the REW/s  
button to go back one step) until the part you  
want to correct begins flashing, then make the  
changes pressing the PLAY/K or STOP/L but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30 SP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
4)Press the POWER button to set automatic timer  
recording.  
- 21 -  
EN  
9J27  
 
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
USER’S SET UP  
2 Set “AUTO RETURN” to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO RETURN”.  
Press the F.FWD/B or REW/s  
button until [ON] appears. Then,  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
B
After setting a program;  
1)Press the POWER button.  
2)Repeat steps [1] ~ [2] on page 20 and select a  
program you want to cancel.  
3)Press the T-PROG. CLEAR button.  
4)Press the MENU button on the remote control to  
return to TV mode.  
press the MENU button on the remote control to  
return to TV mode.  
3 Auto Return will begin  
When all the timer recordings are completed, the  
TV/VCR will rewind to the beginning of the recorded  
While recording is in progress;  
1)Press POWER button.  
program(s).  
NOTE:  
2)Press the STOP/EJECT button on the TV/VCR.  
TO CHECK THE BEGIN/END TIME  
1)Press the POWER button so that the REC indicator  
goes off.  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
2)Press the MENU button on the remote control.  
3)Confirm “TIMER PROGRAMMING” is pointed.  
4)Press the F.FWD/B button. The details of pro-  
grams appear on the TV screen.  
5)Press the MENU button on the remote control to  
return to TV mode.  
4 Watch the recorded program  
Press the PLAY button.  
TO CANCEL THE AUTO RETURN  
MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Then, press the MENU  
button on the remote control to return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
Make sure the channel you want to record is prop-  
erly set in advance.  
It is not necessary to press the RECORD button for  
timer recording.  
WAKE UP TIMER  
Recording begins automatically at the Start time.  
If you are recording using a Timer mode, you may  
not operate the unit manually.  
The Wake Up Timer function turns on the TV/VCR  
without using the POWER button after a desired  
period of time.  
NOTES:  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette  
will be ejected when the POWER button is pressed  
to off.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, and the tape will be ejected.  
Use the remote control for this procedure.  
Clock must be set to the correct time before setting  
the timer.  
If you want to select [TAPE], you must insert a  
cassette tape in the TV/VCR. The tape will start  
playback automatically on your desired time.  
1 Select “WAKE UP TIMER”  
Press the WAKE-UP/SLEEP button  
on the remote control once, and  
confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s  
AUTO RETURN  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
WAKE UP B ON/OFF [ON]  
TIMER  
TV/TAPE [TV]  
TIME  
[12:00AM]  
button until [ON] appears.  
1 Select “USER’S SET UP”  
2 Select “TV” or “TAPE”  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
Press the PLAY/K or STOP/L but-  
ton until to point to “TV/TAPE”.  
Press the F.FWD/B or REW/s  
button, and select [TV] or [TAPE].  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
CHANNEL SET UP  
B
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
TIME SEARCH  
WAKE UP  
TIMER  
ON/OFF [ON]  
B TV/TAPE [TV]  
TIME  
[12:00AM]  
- 22 -  
EN  
9J27  
 
SLEEP TIMER  
The Sleep Timer function turns off the TV/VCR  
without using the POWER button after a desired  
period of time.  
3 Set wake up time  
Press the PLAY/K or STOP/L but-  
ton until to point to “TIME”.  
Press the F.FWD/B or REW/s  
button until your desired wake up  
time appears.  
NOTE:  
WAKE UP  
TIMER  
ON/OFF [ON]  
TV/TAPE [TV]  
B TIME  
[12:00AM]  
This function does not operate during Recording  
mode.  
Each additional push will increase (or decrease) the  
time by 10 minutes.  
1 Select “SLEEP TIMER”  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
4 Exit the Wake Up Timer setting  
Press the MENU button on the remote control to  
return to TV mode.  
2 Set sleep time  
TO CANCEL THE WAKE UP TIMER  
Press the PLAY/K, STOP/L,  
F.FWD/B or REW/s button until  
Press the WAKE-UP/SLEEP button on the remote  
control once, and confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s button until [OFF]  
appears.  
SLEEP TIMER [2:00]  
your desired sleep time appears.  
Each additional push will increase  
the time by 30 minutes up to 120 minutes.  
Press the MENU button on the remote control to exit  
the Sleep Timer setting.  
TO CANCEL THE SLEEP TIMER  
Press the WAKE-UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
To view the time left for sleep timer, press the  
WAKE-UP/SLEEP button twice, then press the  
MENU button on the remote control to exit the sleep  
timer setting.  
COPYING A VIDEO TAPE  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
1)Insert a pre-recorded video cassette into the Source  
(Playing) VCR or camcorder.  
2)Insert a blank video cassette, or one you want to  
record over, into the TV/VCR’s cassette compart-  
ment.  
3)Press the SPEED button on remote control for the  
TV/VCR to select the desired recording speed  
(SP/SLP).  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
Connect your TV/VCR and a Source (Playing) VCR  
using the following diagram.  
4)Press the CHANNEL K or L button on the  
TV/VCR until “AUX” appears on the screen.  
NOTE: “AUX” is found below the lowest memo-  
rized channel. (Example: CH2)  
POWER  
VIDEO AUDIO  
[The TV/VCR]  
REC  
5)Press the RECORD button on the TV/VCR.  
6)Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
NOTE: For best results during dubbing, use the  
TV/VCR’s front panel controls whenever possible.  
The remote control might affect the source (Playing)  
VCR’s playback operation.  
[Ex: Source (playing)  
VCR or camcorder]  
7)To stop copying, press STOP/EJECT button on the  
TV/VCR, then stop the tape on the source VCR or  
camcoder.  
AUDIO  
Audio/Video  
adapter cable  
(not supplied)  
OUT  
IN  
VIDEO  
- 23 -  
EN  
9J27  
 
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
<Off mode>  
<Counter mode>  
<Clock mode>  
Counter mode: After 5 seconds, only  
the counter remains. To clear it, press  
the DISPLAY button.  
Clock mode: After 5 seconds, only  
the clock and the channel number  
remain. To clear them, press the DIS-  
PLAY button.  
5:40PM  
CH2  
Press  
once  
Press  
once  
COUNT 0:12:34  
Press once  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
This shows the elapsed recording or playback time in  
hours, minutes, and seconds. (The displayed time  
will not change on a blank tape or blank portions on  
the tape.)The “–” indication will appear when the  
tape has rewound further than “0:00:00” on the tape  
counter.  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR will eject the tape and turn  
itself to off.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
MAINTENANCE  
1.Please visit your local Audio/Video store and pur-  
CABINET CLEANING  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-242-7158, to  
locate an Authorized Service Center.  
NOTES:  
Wipe the front panel and other exterior surfaces of  
the TV/VCR with a soft cloth immersed in luke-  
warm water and wrung dry.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/VCR. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
AUTO HEAD CLEANING  
SERVICING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
Should your TV/VCR become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
242-7158, to locate an Authorized Service Center.  
Playback picture may become blurred of interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use, or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
back, the video heads in your TV/VCR may need  
to be cleaned.  
- 24 -  
EN  
9J27  
 
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,  
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to  
remedy the problem.  
PROBLEM  
CORRECTIVE ACTION  
No power.  
Make sure the AC cord is connected to an AC outlet.  
Make sure the car battery cord is connected to vehicle’s cigarette  
lighter socket and to DC 13.2V (12V) jack on back of the TV/VCR.  
Check the fuse (5A, 250V) in car battery cord.  
Make sure the power is turned on.  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Let the TV/VCR program it's tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the TV/VCR clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
No picture and sound.  
No picture or poor picture on  
TV/VCR.  
No sound or poor sound.  
Timer recording is not possible.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
Adjust tracking control for a better picture using the CHANNEL  
or L button on the TV/VCR.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 24.  
K
No picture but the audio is OK in  
playback.  
No operation by infrared Remote  
Control.  
Video or color fades in and out  
when making a copy of a video tape  
Can not set the auto clock to ON.  
Different color makes on screen.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
copy guard protection.  
.
Make sure the AC cord is connected to an AC outlet.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the TV/VCR away from the appli-  
ances, the TV/VCR can repair itself automatically. If you want to  
repair immediately, unplug the TV/VCR power cord, then plug it in  
again 30 minutes or so later.  
- 25 -  
EN  
9J27  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
CRT :  
9 inch in-line gun, 90˚  
deflection tube  
NTSC-M  
Rotary two-head  
1/2 inch  
Video input level :  
Audio input level :  
0.5~2.0Vp-p  
-15dBs  
Television system :  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
Video S/N ratio : More than 46dB  
Audio S/N ratio : More than 43dB  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
OTHER SPECIFICATIONS  
Power requirement : AC 120V/60Hz  
DC 13.2V  
Power consumption : AC 55W / DC 60W  
Dimensions :  
#2~#6  
#7~#13  
#14~#69  
H:12-7/8” (326mm)  
W:12-1/16” (306mm)  
D:12-3/4” (324mm)  
18.5 lbs (8.4kg)  
CATV  
VHF :  
Weight :  
5A  
MID band :  
SUPER band :  
HYPER band :  
Terminals  
A5~A1, A~I  
J~W  
W+1~W+84  
Designs and specifications are subject to change  
without notice.  
If there is a discrepancy between languages, the  
default language will be English.  
Antenna input :  
VHF/UHF 75 ohms  
unbalanced  
Video input :  
Audio input :  
Earphone :  
RCA connector [ 1  
RCA connector [ 1  
1/8” monaural (3.5 mm)  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 26 -  
EN  
9J27  
 
CONTROLES DE OPERACIÓN Y SUS FUNCIONES  
NOTA:  
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un  
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el  
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del  
mando a distancia universal.  
- PANEL DELANTERO -  
POWER  
STOP/EJECT  
REW  
PLAY  
F.FWD  
REC/OTR  
VOLUME  
CHANNEL  
VIDEO AUDIO  
EARPHONE  
REC  
1 2 3 4  
- CONTROL REMOTO -  
5
6 7 8 9 10 11  
12 13 14  
6 Botón de parada (STOP)– Púlselo para detener  
la cinta.  
25  
6
Botón de expulsión (EJECT)–Púlselo en el  
modo de parada para expulsar la cinta del televi-  
sor/videograbadora.  
WAKE-UP  
/SLEEP  
POWER  
EJECT  
5
CHANNEL  
RETURN  
Botón L–  
1
4
7
2
5
8
3
6
9
24  
Púlselo para seleccionar los modos de ajuste desde  
el menúde la pantalla.  
15  
CHANNEL  
VOLUME  
12  
Púlselo para introducir dígitos cuando establezca  
un programa.  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
7 Botón de rebobinado (REW)– Púlselo para  
rebobinar la cinta, o para ver la imagen en retroceso  
rápido durante el modo de reproducción. (Búsqueda  
con rebobinado)  
0
+100  
MENU  
DISPLAY  
MUTE  
11  
16  
17  
7
23  
8
PLAY  
9
REW  
F.FWD  
STOP  
6
Botón s–  
SPEED PAUSE/STILL  
RECORD  
Púlselo para seleccionar un modo desde un menú-  
22  
21  
10  
18  
particular.  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
8 Botón de reproducción (PLAY)– Púlselo para  
iniciar la reproducción.  
COUNTER  
RESET  
19  
20  
Botón K–  
Púlselo para seleccionar los modos de ajuste desde  
1 Toma de entrada de vídeo (VIDEO)–  
Conéctela a la toma de salida de vídeo de su  
videocámara u otra videograbadora.  
el menú de la pantalla.  
Púlselo para introducir dígitos cuando establezca  
un programa.  
2 Toma de entrada de audio (AUDIO)–  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
9 Botón de avance rápido (F.FWD)– Púlselo para  
avanzar rápidamente la cinta, o para ver la imagen  
en avance rápido durante el modo de reproducción.  
(Búsqueda con avance rápido)  
Conéctela a la toma de salida de audio de su equipo  
de audio, videocámara u otra videograbadora.  
3 Indicador de grabación (RECORD)– Parpadea  
durante la grabación.  
Se enciende en el modo de espera de la grabación  
con temporizador.  
Botón B–  
4 Ventanilla sensora del mando a distancia–  
Recibe las señales infrarrojas procedentes del  
mando a distancia.  
5 Botón de la alimentación (POWER)– Púlselo  
para encender y apagar el televisor/videograbadora.  
Púlselo para activar la grabación con temporizador.  
Cuando establezca un programa (por ejemplo: para  
ajustar el reloj o para establecer un programa de  
temporizador), púlselo para determinar su elección y  
vaya al paso siguiente que quiera introducir.  
Púlselo para determinar los modos de ajuste desde  
el menú de la pantalla.  
- 27 -  
EN  
9J27  
 
- PANEL TRASERO -  
27  
26  
28  
Púlselo para seleccionar un modo desde un menú-  
18 Botón de velocidad de cinta (SPEED)–  
particular.  
Púlselo para elegir la velocidad de grabación desea-  
da: SP/SLP.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
10 Botón de grabación (REC)– Púlselo para ini-  
ciar la grabación manual.  
19 Botón T-PROG. CLEAR– Púlselo para cancelar  
un programa de temporizador.  
Botón de grabación de un toque (OTR)–  
Activa la grabación de un toque. (Sólo en el televi-  
sor/videograbadora)  
Botón de reposición del contador  
(COUNTER RESET)– Púlselo para reponer el  
contador a 0:00:00.  
11 Botones de volumen (VOLUME X / Y)–  
20 Botón de juego (GAME)– Establece el modo  
del juego y el modo de entrada externa al mismo  
tiempo.  
Ajustan el nivel del volumen.  
12 Botones de canales (CHANNEL K/ L)–  
Púlselos para seleccionar los canales deseados para  
ver o grabar.  
21 Botón de búsqueda con tiempo (TIME  
SEARCH)– Púlselo para activar el modo de  
búsqueda con tiempo.  
Se puede mostrar el menú principal en la pantalla del  
televisor pulsando repetidamente este botón del tele-  
visor/videograbadora.  
22 Botón de pausa/imagen fija  
(PAUSE/STILL)– Púlselo para detener temporal-  
mente la cinta durante la grabación o para ver una  
imagen fija durante la reproducción.  
Función de seguimiento– Pulse los botones  
para minimizar el ruido de vídeo (líneas o puntos  
en la pantalla) durante la reproducción.  
13 Toma de auriculares (EARPHONE)– Para  
conectar los auriculares (no suministrados) y  
escuchar en privado. La toma es mono y tiene un  
tamaño de 1/8”(3.5 mm).  
14 Compartimiento del videocasete  
15 Botones numerados– Púlselos para seleccionar  
los canales deseados para ver o grabar. Para selec-  
cionar canales del 1 al 9, pulse primero el botón 0 y  
luego el botón 1 a 9.  
Botón +100– Cuando seleccione canales de tele-  
visión por cable cuyo número sea superior al 99,  
pulse primero este botón, y luego pulse los dos últi-  
mos dígitos. (Para seleccionar el canal 125, pulse  
primero el botón “+100” y luego el “2” y el “5”.)  
16 Botón de menú (MENU)– Púlselo para visu-  
alizar el menú principal en la pantalla del televisor.  
17 Botón del visualizador (DISPLAY)– Visualiza  
el contador o el número del canal actual y la hora  
actual en la pantalla del televisor.  
23 Botón de silenciamiento (MUTE)– Silencia el  
sonido. Púlselo de nuevo para recuperar el sonido.  
24 Botón de retorno de canal (CHANNEL  
RETURN)– Púlselo para volver al canal anterior.  
Por ejemplo, pulsando una vez este botón, la visu-  
alización del canal cambiará de 3 (canal actual) a  
10 (canal anterior), y al pulsarlo por segunda vez,  
el canal cambiará del 10 al 3.  
25 Botón del temporizador despertador/para  
dormir (WAKE-UP/SLEEP)– Ajusta el tempo-  
rizador para despertarse/dormir.  
26 Terminal de antena (ANT.)– Para conectar una  
antena o sistema de televisión por cable.  
27 DC 13.2V– Conecta el cordón para la batería del  
automóvil.  
28 Cordón de alimentación– Conéctelo a la toma  
de CA estándar (120V/60Hz).  
- 28 -  
EN  
9J27  
 
CONEXIONES DE ANTENA/CABLE  
Desde el cable coaxial  
o caja de emisiones vía  
satélite de 75 ohm del  
sistema de Cable  
Antena combinada de  
VHF/UHF  
(no incluído)  
Antena Dipolar  
(incluído)  
OUT  
IN  
Caja de CATV  
o caja de emi-  
siones vía satélite  
(no incluído)  
Antena VHF  
(no incluído)  
Adaptador de  
acoplo (incluído)  
o
Desde el  
sistema de Cable  
Antena UHF  
(no incluído)  
Combinador de  
VHF/UHF  
(no incluído)  
o
o
ANT.  
Cable coaxial  
de 75 ohm (no  
incluído)  
o
Cable bifilar plano  
realizar la grabación automática con temporizador.  
NOTA: Con esta unidad SÓLO se podrá grabar y ver  
un mismo canal al mismo tiempo.  
CABLE CON CONVERTIDOR/DESCODI-  
FICADOR O CONVERTIDOR DE EMI-  
SIONES VÍA SATÉLITE  
CONEXION DE LA ANTENA BIPOLAR  
1.Introduzca la varilla de la antena bipolar (incluído)  
en el orificio destinado para la antena, en la parte  
trasera de la TV/VCR.  
2.Conecte el cable bifilar plano de la antena bipolar  
al adaptador de acoplo (incluído) de 300/75 ohm.  
3.Enchufe el adaptador de acoplo al terminal ANT de  
la TV/VCR, como lo muestra el dibujo.  
Para obtener una mejor recepción, extienda la antena  
de varilla y regule su longitud y posición. (Evite  
tocar su parte superior mientras hace los ajustes.)  
NOTAS: Si es difícil obtener una buena recepción  
con la antena de interiores, se recomienda usar una  
antena de exteriores. Antes de instalar una antena de  
exteriores al aparato, se debe desconectar la antena  
de interiores.  
Si su servicio de televisión por cable le suministra un  
convertidor, o si usted utiliza un sistema de emisiones  
vía satélite, usted podrá utilizar las conexiones básicas.  
Utilizando estas conexiones, usted también podrá  
grabar canales codificados. Sin embargo, la selección  
de los canales deberá hacerse con el convertidor de  
televisión por cable con el convertidor de emisiones  
vía satélite. Esto significa que los canales no podrán  
ser cambiados con el mando a distancia del televi-  
sor/videograbadora. La grabación inatendida se limita  
a un canal cada vez.  
ANTENA COMBINADA DE VHF/UHF  
PARA GRABAR UN CANAL  
CODIFICADO/DESCODIFICADO  
1.Ajuste el selector de canales del  
Una antena de combinación de 75 ohm para  
VHF/UHF puede ser conectada al terminal ANT.  
televisor/videograbadora al canal de salida del con-  
vertidor de televisión por cable o del convertidor  
de emisiones vía satélite. (Ej.: CA3)  
2.Seleccione el canal que desee grabar de su conver-  
tidor de televisión por cable o del convertidor de  
emisiones vía satélite.  
ANTENAS SEPARADAS DE VHF/UHF  
En algunos lugares será necesario utilizar una antena  
exterior.  
CABLE SIN CONVERTIDOR/DESCODIFI-  
CADOR  
Aviso a los instaladores de sistemas CATV:  
Utilice esta conexión si su sistema de televisión por  
cable se conecta directamente a su  
televisor/videograbadora sin convertidor.Utilizando  
esta conexión usted podrá:  
1)Utilizar el mando a distancia del  
televisor/videograbadora para seleccionar canales.  
2)Programar uno o más canales sin codificar para  
Este aviso se incluye para que los instaladores de sis-  
temas CATV tenga en cuenta el Artículo 820-40 del  
NEC, que proporciona consejos para hacer una conexión  
apropiada a tierra y, en particular, especifica que el cable  
de tierra deberá conectarse a un sistema de puesta a tier-  
ra del edificio tan cerca del punto de entrada del cable  
como sea posible.  
- 29 -  
EN  
9J27  
 
CONEXION MOVIL  
Al zócalo del encendedor  
de cigarrillos el cordón  
para la batería del coche  
ADVERTENCIA: El conductor nunca debe ver  
programas del televisor o del videobgrabadora  
mientras está conduciendo un vehículo.  
PRECAUCIÓN: Si usted usa la TV/VCR con el  
motor del vehículo apagado, recargue la batería  
del vehículo aprox. cada 4 horas de uso, para  
evitar que ésta se agote. Cuando termine de usar  
la TV/VCR, siempre desenchufe el cordón para  
la batería del automóvil del zócalo del encende-  
dor de cigarrillos.  
Antena de VHF/UHF  
para TV móvil  
(no incluído)  
Cordón para la batería  
del automóvil  
DC13.2V  
ANT.  
1)La antena de interiores incluída es adecuada para  
usar cuando el vehículo está inmóvil. Para obtener  
una mejor recepción en ruta, utilice una antena de  
VHF/UHF para TV móvil de alta calidad.  
2)Enchufe el cordón para batería de automóvil al conec-  
tor DC13.2V (12V) en la parte posterior de la  
INSTALACIÓN DE LAS PILAS  
TV/VCR. Luego conecte el otro extremo en el zócalo  
para el encendedor de cigarrillos del automóvil.  
1)Abra la tapa del compartimiento de las pilas del  
mando a distancia presionándola en el sentido de  
la flecha.  
2)Inserte 2 pilas tamaño “AA” en el compartimiento  
de las pilas, en el sentido indicado por las marcas  
de polaridad (+/-).  
NOTAS:  
Confirme que su vehículo tlene un sistema eléctrico  
a tierra negativo de 13.2 (12) voltios.  
Confirme que está usando sólo el cordón provisto  
para la batería del automóvil. El uso de otro cordón  
puede dañar su TV/VCR.  
3)Vuelva a poner la tapa.  
Asegúrese que no haya cenizas ni otro restos en el  
zócalo del encendedor.  
Asegúrese de introducir completamente el enchufe  
del cordón de la batería del automóvil en el zócalo  
del encendedor de cigarrillos.  
Siempre desenchufe primero del zócalo del  
encendedor de cigarrillos el cordón para la batería  
del coche, antes de desconectarlo de la TV/VCR.  
Antes de usar la alimentación de CA, usted debe  
desconectar de la TV/VCR el cordón para la batería  
del automóvil.  
Solamente reemplace un fusible por otro del mismo  
tipo 5A, 250V.  
Asegúrese de que el cable de CA esté bobinado  
como se muestra más abajo.  
MODO DE ENTRADA EXTERNA  
Cuando utilice una señal de entrada externa (otra  
videograbadora o una videocámara), conecte los  
cables de salida de audio/vídeo del equipo de repro-  
ducción a las tomas AUDIO IN/VIDEO IN de su  
televisor/videograbadora. Y luego pulse el botón  
CHANNEL K o L hasta que “AUX” aparezca en la  
pantalla.  
Usted puede programar el temporizador para que  
explore todos los canales que puedan recibirse en su  
zona.  
SELECCION DE IDIOMA  
1 Enchufe el cordón de alimentación  
del televisor/videograbadora  
Enchufe el cordón de alimentación del  
televisor/videograbadora en una toma de  
CA estándar.  
NOTA:  
Si aparecen algunas cifras en la esquina  
de la pantalla, pulse el botón POWER sin desench-  
ufar el cordón de alimentación.  
- 30 -  
EN  
9J27  
 
AJUSTE DE CANAL  
A continuación, pulse el botón  
F.FWD/B.  
El sintonizador busca y memoriza  
todos los canales activos en su  
localidad.  
Asegúrese de que ...  
AGREGAR/BORRAR (CATV)  
Pulse el botón POWER para encender el televi-  
sor/videograbadora.  
B AUTOPROGRAMACION DE CA.  
NOTA: Esta función afecta sólo el idioma en el  
menú de la pantalla y no la fuente de audio.  
– M E N U –  
2 Seleccione “LANGUAGE”  
3 Después de buscar  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
LANGUAGE [ENGLISH]  
ZERO RETURN  
TIME SEARCH  
Pulse el botón MENU en el mando  
El sintonizador se detiene en el canal memorizado  
más bajo.  
a distancia.  
Pulse el botón PLAY/K o STOP/L  
para señalar “LANGUAGE”.  
B
Cuando se activa AUTOPROGRAMACION DE  
CA, donde no hay entrada de señal del televisor,  
aparecerá “NO HAY SEÑAL DE TV” en la pan-  
talla después de terminar la búsqueda de canales.  
3
Seleccione “ENGLISH”, “ESPAÑOL” o FRANÇAIS”  
El televisor/videograbadora puede reconocer los  
Seleccione “ENGLISH”, “ESPAÑOL” o  
“FRANÇAIS” con el botón F.FWD/B y pulse el  
botón REW/s en el mando a distancia.  
canales de TV para que sean canales de TV de  
antena de cable con las condiciones de recepción.  
En este caso, pruebe nuevamente con el prefijado  
automático en las condiciones de recepción fina.  
4 Salga del modo de idioma  
Pulse el botón MENU en el mando a distancia para  
volver al modo del televisor.  
AJUSTE DEL RELOJ  
NOTA: Si, por alguna razón, el menú está en español  
o francés, pulse el botón MENU en el mando a distan-  
cia, pulse el botón PLAY/K para señalar el “IDIOMA  
(ESPAÑOL)” o “LANGAGE (FRANÇAIS)”, a con-  
tinuación, pulse el botón F.FWD/B y pulse el botón  
MENU en el mando a distancia.  
Cerciórese...  
La alimentación del televisor/videograbadora  
deberá estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 6 de mayo de 2004  
HORA: 5:40 PM  
1)Pulse el botón MENU en el mando a distancia.  
Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE RELOJ”.  
AJUSTE DE CANAL  
Puede programar el sintonizador para buscar todos  
los canales que recibe en su localidad.  
Luego, pulse el botón F.FWD/B.  
NOTA: El canal preparado NO es necesario cuando  
esté conectado a una caja de cable o caja de satélite.  
Sólo tiene que seleccionar con el selector de canal  
del televisor/videograbadora al canal de salida de la  
caja de cabe o caja de satélite (por ejemplo el canal  
CH3). Seleccione el canal a ver en la caja de cable o  
caja de satélite.  
2)Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE MANUAL RELOJ”.  
Luego, pulse el botón F.FWD/B.  
3)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el mes deseado. (Ejemplo: Mayo - 05)  
Luego, pulse el botón F.FWD/B.  
4)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el día del mes deseado. (Ejemplo: 6 - 06)  
Luego, pulse el botón F.FWD/B.  
5)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el año deseado. (Ejemplo: 2004)  
Luego, pulse el botón F.FWD/B.  
6)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca la hora deseada. (Ejemplo: 5, PM)  
Luego, pulse el botón F.FWD/B.  
7)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el minuto deseado. (Ejemplo: 40)  
8)Pulse el botón MENU en el mando a distancia.  
Aunque los segundos no se visualizan, éstos  
empiezan a contar desde 00 cuando se pulsa  
MENU en el mando a distancia. Utilice esta fun-  
ción para sincronizar el reloj con la hora correcta.  
Asegúrese de que ...  
Pulse el botón POWER para encender el televi-  
sor/videograbadora.  
1 Seleccione “AJUSTE DE CANAL”  
– M E N U –  
Pulse el botón MENU en el mando  
COMO PROGRAMAR  
CONTROL DE IMAGEN  
a distancia.  
AJUSTE RELOJ  
B
AJUSTE DE CANAL  
AJUSTE DE USER  
IDIOMA [ESPAÑOL]`  
RETORNO A CERO  
BUSQUEDA DE HORA  
Pulse el botón PLAY/K o el botón  
STOP/L para señalar “AJUSTE DE  
CANAL”.  
A continuación, pulse el botón F.FWD/B.  
2 Empiece el prefijado automático  
Pulse el botón PLAY/K o STOP/L para señalar  
“AUTOPROGRAMACION DE CA”.  
- 31 -  
EN  
9J27  
 
FUNAI CORPORATION  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workman-  
ship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this  
warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date  
of original retail purchase.  
LIMITS AND EXCLUSIONS:  
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail  
purchase will be required together with the product to obtain service under this warranty.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does  
not apply to any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE  
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE  
UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
To locate your nearest FUNAI Authorized Service Center or for general service procedure, please  
call 1-800-242-7158 or write to the following:  
FUNAI CORPORATION, INC.  
SERVICE CENTER  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel :1-800-242-7158  
Head Office: 100 North Street, Teterboro, NJ 07608  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Malaysia  
0EMN02466  
T4501UB * * * * *  
 

Sharp Flat Panel Television TINS E517WJZZ User Manual
Sharp Microwave Oven JT 369 User Manual
Singer Sewing Machine XL 5000 User Manual
Sony Indoor Furnishings SU FL61 User Manual
Sony Laptop PCG F270 User Manual
Sony MiniDisc Player MZ E40 User Manual
Spalding Fitness Equipment 214973A User Manual
Speco Technologies Security Camera VL 262SD User Manual
Sunbeam Juicer JE7600 User Manual
Sylvania VCR SRV2306 User Manual