Sylvania VCR SSV6001 User Manual

VIDEO  
CASSETTE  
RECORDER  
OWNER’S  
MANUAL  
SSV6001  
TABLE OF CONTENTS  
IMPORTANT SAFEGUARDS..................................... 2  
PRECAUTIONS ............................................................ 3  
FEATURES ................................................................... 4  
OPERATING CONTROLS AND FUNCTIONS......... 4  
PREPARATION FOR USE .......................................... 6  
INITIAL SET UP FOR USE ........................................ 7  
SET UP FOR USE AGAIN........................................... 8  
PLAYBACK FUNCTION.............................................. 9  
RECORDING FUNCTION ........................................ 10  
TIMER RECORDING................................................. 11  
SPECIAL FEATURES................................................ 12  
TROUBLESHOOTING GUIDE................................. 12  
SPECIFICATIONS ..................................................... 13  
MAINTENANCE......................................................... 13  
INSTRUCCIONES EN ESPAÑOL............................ 14  
WARRANTY ................................................................ 16  
SUPPLIED ACCESSORIES  
ACCESSORIES  
Coaxial Cable  
Remote Control Unit  
Batteries  
PART NO.  
WPZ0901LW001  
N9374UD or N9377UD  
AA x 2  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY  
S
TAR®  
Partner, our company has  
determined that this product meets  
If you need additional operating assistance after reading this  
the ENERGY S  
TAR® guidelines for  
S
TAR® is  
owners manual or to order replacement accessories, please call  
energy efficiency. ENERGY  
a U.S. registered mark.  
TOLL FREE : 1-800-968-3429.  
Please read before using this equipment.  
 
PRECAUTIONS  
INSTALL LOCATION  
For safety and optimum performance of your VCR:  
REMOTE CONTROL  
We do not recommend the use of universal remote con-  
trols. Not all of the functions may be controlled with a  
universal remote control.  
If you decide to use a universal remote control with this  
unit, please be aware that the code number given may  
not operate this unit. In this case, please call the manu-  
facturer of the universal remote control.  
Install the VCR in a horizontal and stable position.  
Do not place anything directly on top of the VCR. Do  
not place the VCR directly on top of the TV.  
Shield it from direct sunlight and keep it away from  
sources of intense heat. Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
on the sides of the VCR. Avoid locations subject to  
strong vibration or strong magnetic fields.  
FCC WARNING  
This equipment may generate or use radio frequency  
energy. Changes or modifications to this equipment may  
cause harmful interference unless the modifications are  
expressly approved in the instruction manual. The user  
could lose the authority to operate this equipment if an  
unauthorized change or modification is made.  
AVOID THE HAZARDS OF ELECTRICAL  
SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting it  
from AC wall outlet. Grasp it by the plug.  
IMPORTANT COPYRIGHT INFORMATION  
If, by accident, water is spilled on your VCR, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Unauthorized recording or use of broadcast television  
programming, video tape, film or other copyrighted ma-  
terial may violate applicable copyright laws. We as-  
sume no responsibility for the unauthorized duplication,  
use, or other acts which infringe upon the rights of copy-  
right owners.  
Do not put your fingers or objects into the VCR cas-  
sette holder.  
MOISTURE CONDENSATION  
WARNING  
Moisture condensation may occur inside the unit when  
it is moved from a cold place to a warm place, or after  
heating a cold room or under conditions of high humid-  
ity. Do not use the VCR at least for2 hours until itsinside  
is dry.  
A NOTE ABOUT RECYCLING  
This products packaging materials are recyclable and  
can be reused. Please dispose of any materials in accord-  
ance with your local recycling regulations.  
Batteries should never be thrown away or incinerated  
but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
VIDEO CASSETTE TAPE  
This VCR will operate with any cassette that has the  
SERIAL NUMBER  
mark. For best results, we recommend the use  
of high-quality tapes. Do not use poor quality ordam-  
aged tapes.  
The serial number of this product may be found on the  
back of the VCR. No other VCR has the same serial  
number as yours. You should record the number and  
other vital information here and retain this book as a  
permanent record of your purchase to aid identification  
in case of theft. Serial numbers are not kept on file.  
Avoid moisture. Moisture condensation may occur  
on the tape if it is moved from a cold place to a warm  
place or visa versa. Before using a tape with these  
conditions, to avoid damage of the tape and your  
VCR, wait until the tape has warmed to room tem-  
perature and the moisture has evaporated.  
Avoid extreme heat, high humidity and magnetic  
fields.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
Serial No.  
You can prevent accidental erasing  
of a recording by breaking off the  
tab on the back edge of the cassette.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,  
FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLEC-  
TRIQUES, INTRODUIRE LA LAME LA PLUS  
LARGE DE LA FICHE DANS LA BORNE CORRE-  
SPONDANTE DE LA PRISE ET POUSSER  
JUSQUAU FOND.  
If you decide to record on the tape  
Tab  
again, cover the hole with plastic  
tape.  
Download from Www.Somanuals.-co3m-. All Manuals Search And Download.  
EN  
0J01  
FEATURES  
Hardware specifications  
Auto Head Cleaner  
4 Head HiFi Stereo  
Playback  
S-VHS Quasi Playback (SQPB)  
(Allows you to view a tape recorded in S-VHS format.)  
Auto Repeat  
Bilingual on-screen menu display selectable in  
English or Spanish  
2 Step Picture Search Operation  
181 channel capability PLL frequency synthesizer  
tuner with direct station call  
(A cable converter box may be necessary to view  
scrambled cable channels.)  
Index Search  
Time Search  
Recording  
1 Year, 7 events (including Daily and Weekly  
Timer Recording)  
OTR (One Touch Recording)  
Automatic functions  
Auto power on and off system  
Digital Auto Tracking (DTR)  
OPERATING CONTROLS AND FUNCTIONS  
VCR FRONT PANEL  
REMOTE CONTROL  
2
4 5 6  
1
3
STOP/EJECT  
PLAY  
POWER  
VCR/TV EJECT  
3
REW  
F.FWD  
7
3
8
1
2
5
8
0
REC/OTR  
PAUSE/STILL  
CHANNEL  
6
VIDEO  
L
AUDIO  
R
4
7
12  
TAPE IN  
TIMER  
REC  
POWER  
VCR/TV  
MENU  
15  
9
MENU  
+100 SEARCH MODE  
8
26 23  
7
10  
11  
12  
22  
13  
14  
VCR REAR PANEL9  
20  
19  
18  
4
14  
16  
17  
DISPLAY SLOW EXIT COUNTER  
21  
23 24  
MEMORY  
PLARYESET  
REW  
F.FWD  
2
3
5
6
ANT  
IN  
AUDIO  
L
STOP  
PAUSE/STILL  
RECORD  
OUT IN  
R
13  
VIDEO  
OUT  
CH4  
OUT INCH3  
25 26 27 28  
1. Cassette Compartment  
4. PLAY buttonPress to begin playback.  
2. REW buttonPress to rewind the tape, or to view  
the picture rapidly in reverse during the playback  
mode. (Rewind Search)  
Press to enter digits when setting program (For ex-  
ample: setting clock or timer program).  
Press to select the setting modes from the on screen  
menu.  
Press to cancel a setting of timer program. Press to  
correct digits when setting program (For example: 5. F.FWD buttonPress to rapidly advance the tape, or  
setting clock or timer program). Press to add or delete  
channel numbers during channel preset.  
view the picture rapidly in forward during playback.  
(Forward Search)  
3. EJECT buttonPress to remove the tape from the  
When setting program (For example: setting clock or  
timer program), press to determine your selection  
and proceed to the next step you want to input. Press  
to determine the setting modes from the on screen  
menu. Press to add or delete channel numbers during  
channel preset.  
VCR.  
STOP buttonPress to stop the tape motion.  
Press to enter digits when setting program (For ex-  
ample: setting clock or timer program). Press to se-  
lect the setting modes from the on screen menu.  
Download from Www.Somanuals.-co4m-. All Manuals Search And Download.  
EN  
0J01  
6. PAUSE/STILL buttonPress to temporarily stop 16. DISPLAY buttonPress to display the current time,  
the tape during recording or to view a still picture  
during playback.  
Frame Advance functionPress to advance the  
picture by one frame at a time during still mode.  
channel number, real time tape counter, and other in-  
formation on the TV screen. (only on the remote con-  
trol)  
Each time you press this button, TV screen will  
change as shown. The status display (STOP, PLAY  
etc.) and the tape speed display (SP, LP (playback  
only), or SLP) will disappear after 5 seconds.  
7. POWER buttonPress to turn VCR on and off.  
Press to activate timer recording, when the timer pro-  
gram has been set.  
8. VCR/TV buttonPress to select TV or VCR mode.  
<COUNT mode>  
<CLOCK mode>  
<OFF mode>  
STOP  
STOP  
5:40PM  
CH 02  
VCR position: to view playback, to monitor video  
recordings or watch TV using the VCR tuner.  
Press  
once  
Press  
once  
SP  
0:12:34  
SP  
TV position: to watch TV or to view one program  
while recording another.  
Press once  
9. Remote sensor windowReceives the infrared  
signals from the remote control.  
10. Indicators  
17. SLOW buttonPress to start slow motion playback.  
(only on the remote control)  
POWER indicatorIndicates that the power is  
turned on.  
VCR/TV indicatorIndicates that the VCR is in the  
VCR position.  
TAPE IN indicatorIndicates that there is a tape in  
the VCR.  
TIMER indicatorIndicates that the timer recording  
or OTR has been set.  
18. COUNTER MEMORY buttonPress to set counter  
memory on and off. (only on the remote control)  
19. COUNTER RESET buttonPress to reset counter  
to 0:00:00. (only on the remote control)  
EXIT buttonPress to exit the menu on the TV  
screen. (only on the remote control)  
20. SEARCH MODE buttonPress to perform a Time  
Search or an Index Search. (only on the remote con-  
trol)  
REC indicatorIndicates that it is recording.  
Flashes when a recording has been paused.  
21. Power cordConnect to a standard AC outlet  
11. TAPE SPEED buttonPress to choose the desired  
(120V/60Hz).  
recording speed : SP/SLP. (only on the VCR)  
22. AUDIO OUT jacksConnect to the audio input  
12. CHANNEL Up or Down buttonsPress to select  
jacks of your audio equipment or another VCR.  
the desired channels for viewing or recording.  
23. AUDIO IN jacksConnect to the audio output jacks  
Tracking functionPress to minimize video noise’  
(lines or dots on screen) during playback (only on the  
VCR) or slow mode.  
Press to stabilize the picture in the Still mode when  
the picture begins to vibrate vertically.  
of your audio equipment or another VCR.  
24. ANT. IN terminalConnect to an antenna, Cable  
system or Satellite system.  
25. VIDEO OUT jackConnect to the video input jack  
of your video camera or another VCR.  
13. RECORD buttonPress for manual recording.  
26. VIDEO IN jackConnect to the video output jack of  
OTR buttonPress to activate One Touch Record-  
ing. (only on the VCR)  
your video camera or another VCR.  
27. CH3/CH4 selector switchUse to select a video  
14. MENU buttonPress to display the menu on the TV  
output channel (3 or 4) for VCR playback.  
screen. Press to exit the menu on the TV screen.  
28. ANT. OUT terminalConnects to the antenna input  
15. NUMBER buttonsPress to select desired channels  
for viewing or recording. To select channels from 1  
to 9, first press "0" button then 1 to 9. (only on the  
remote control)  
terminal on your TV.  
INSTALLING THE BATTERIES  
+100 buttonWhen selecting cable channels which  
are higher than 99, press this button first, then press  
the last two digits. (To select channel 125, first press  
"+100" button then press "2" and "5"). (only on the  
remote control)  
1) Open the battery compartment cover by pressing the  
cover on the remote unit in the direction of the arrow.  
2) Insert 2 "AA" penlight batteries into the battery com-  
partment in the direction indicated by the polarity  
(+/-) markings.  
3) Replace the cover.  
Install 2 X AA battery  
Download from Www.Somanuals.-co5m-. All Manuals Search And Download.  
EN  
0J01  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
For some of the most common types of connections, please refer to the diagram below. Use only one connection.  
For any further complex connections, please contact your local dealer. (You may need additional accessories which  
are not supplied).  
1 Disconnect the antenna or cable from your TV.  
2
Connect the antenna orcable totheANT.IN(Topjack)  
of your VCR.  
3 Connect one end of the coaxial cable (supplied) to  
4
Connect the other end of the coaxial cable (supplied)  
to the UHF/VHF antenna jack of your TV.  
the ANT.OUT (Bottom jack) of your VCR.  
Basic Connections  
[Cable Box or Satellite Box]  
OUT  
IN  
From  
Cable or  
Satellite  
Company  
ANT  
AUDIO  
L
OR  
IN  
IN  
OUT  
R
Indoor or  
VIDEO  
OUT  
Audio/Video cables  
(not supplied)  
Outdoor  
Coaxial Cable  
(Supplied)  
CH3 CH4  
IN  
Antenna  
OUT  
OR  
From  
Cable Company  
(No Cable Box)  
Back of the VCR  
IN  
R
IN  
L
VIDEO  
AUDIO  
OR  
VHF  
UHF  
VHF  
OR  
UHF  
ANT in  
STEREO  
TV A/V Terminal  
TV Antenna Terminal  
USING OPTIONAL AUDIO/VIDEO  
OUTPUT JACKS  
If your TV has A/V input jacks, you may connect your  
VCRs AUDIO/VIDEO OUTPUT jacks to the  
audio/video input jacks on back of your TV.  
Direct audio/video connections usually result in a better  
picture and sound quality for tape playback. Please see  
your TVs owners manual for A/V input connections.  
USING AUDIO/VIDEO INPUT JACKS  
You can use the A/V input jacks on the front or the back  
of the VCR.  
1) When you connect the external source to input jacks  
on the back of the VCR, select "L1" position for re-  
cording by pressing the 0, 0, 1 on the remote control  
or CHANNEL Up/Down button.  
2) When you connect the external source to input jacks  
on the front of the VCR, select "L2" position for re-  
cording by pressing the 0, 0, 2 on the remote control  
or CHANNEL Up/Down button.  
Note: "L1" or "L2" is found before the lowest memo-  
rized channel. (Example: CH2)  
Note to CATV system installer  
This reminder is provided to call the CATV system installers attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected  
to the grounding system of the building, as close to the point of cable entry as practical.  
Download from Www.Somanuals.-co6m-. All Manuals Search And Download.  
EN  
0J01  
INITIAL SET UP FOR USE  
5
Begin channel preset  
SETTING THE CH3/CH4  
SWITCH  
by pressing the F.FWD button  
once. The tuner scans and  
memorizes allactivechannels  
in your area.  
CH 01  
If your TV does not have A/V terminals:  
AUTO SET UP  
When the VCR is in the Playback mode or when the  
VCR is in the VCR position, your TV will receive sig-  
nals from the VCR on either channel 3 or 4.  
The VCR distinguishes be-  
tween standard TV channels  
and cable channels.  
To use the VCR with your TV, set the selector switch to  
CH3 or CH4 (which is located  
6
After scanning, the tuner stops on the lowest  
in the back of your VCR),  
memorized channel. The TV screen returns to TV  
mode.  
whichever is not used for nor-  
OUT  
CH3  
CH4  
CH3 CH4  
mal broadcasts in your area.  
Then set your TV to the same  
channel.  
If "AUTO SET UP" appears on the TV screen again,  
check the cable connections. Press the F.FWD button  
once again and the VCR will begin preset again.  
[Back of the VCR]  
AUTOMATIC CHANNEL SET UP  
You can automatically program the tuner to scan only  
the channels you receive in your area.  
TO SELECT A DESIRED CHANNEL  
You can select the desired channel by using the CHAN-  
NELUp or Down button or directly pressing the number  
buttons on the remote control.  
Channel memory programming is NOT needed  
Note for using the number buttons:  
when you connected the VCR to a cable box or  
satellite box as in "Basic connections" on page 6. In  
this case, select the VCR and TV to channel 3 or 4  
the same channel as the CH3 or CH4 switch on the  
back of the VCR. Then, the channel you want to re-  
cord or view may be selected at the cable box or sat-  
ellite box.  
When selecting cable channels which are higher than  
99, press the +100 button first, then press the last two  
digits.  
You must precede single-digit channel numbers with  
a zero (For example: 02, 03, 04 and so on).  
Follow the steps below once. Repeat it only if there  
CLOCK SET UP  
Set the clock accurately for proper automatic timer re-  
cording. We suggest that you use a TV or radio station  
as your time source.  
is a power failure orif the VCR is unplugged formore  
than 30 seconds. (In these cases, the programmed  
channels are erased.)  
You must follow the steps below before attempting  
to play or record a video tape. If you want to play or  
record a video tape BEFORE programming the tuner,  
you can cancel it by pressing the RESET/EXIT but-  
ton. To program the tuner again, see "CHANNEL  
SET UP AGAIN" on the next page.  
1
Select main menu by pressing the MENU button.  
(If the clock is not set, the CLOCK SET menu ap-  
pears first. In this case, follow step [3].)  
2
Select "CLOCK SET" by pressing the PLAY or  
STOP button. Then, press the F.FWD button.  
1 You need to connect the antenna or cable to the VCR  
first. Then, connect the VCR power plug into a stand-  
ard AC outlet.  
3
Set the clock.  
Set the month  
Press the PLAY or STOP button repeatedly.  
Then, press the F.FWD button.  
Press the PLAY or STOP button repeatedly.  
Then, press the F.FWD button.  
Press the PLAY or STOP button repeatedly.  
Then, press the F.FWD button.  
2 Turn on the TV and set the TV to channel 3 or 4.  
Now set the CH3/CH4 switch on the back of the VCR  
to match the channel selected on the TV.  
Set the day  
Set the year  
3 Turn on the VCR by pressing the POWER button.  
Both the POWER indicator and the VCR/TV indica-  
tor on the VCR come on.  
The day of the week will appear automatically.  
Press the PLAY or STOP button repeatedly.  
Then, press the F.FWD button.  
Set the hour  
Press the PLAY or STOP button repeatedly.  
Set the minute  
Set the AM or PM  
4 Select the On Screen Lan-  
LANGUAGE SELECT  
Then, press the F.FWD button.  
————————————————  
CLOCK SET  
guage ("ENGLISH" or  
Press the PLAY or STOP button  
repeatedly.  
B
ENGLISH  
[ON]  
"ESPAÑOL") by pressing  
the PLAY or STOP button.  
Then, press the F.FWD but-  
ton.  
MONTH DAY  
03 19  
YEAR  
MON 2001  
ESPAÑOL  
/
HOUR MINUTE  
05 40  
AM/PM  
PM AM  
PM  
:
To go back one step, press the REW button.  
Start the clock by pressing the RESET/EXIT or  
4
F.FWD button after setting the AM or PM.  
Download from Www.Somanuals.-co7m-. All Manuals Search And Download.  
EN  
0J01  
SET UP FOR USE AGAIN  
TO ADD/DELETE CHANNELS  
CHANNEL SET UP AGAIN  
When the VCR automatically programs the tunerto scan  
only the channels you receive in your area, some chan-  
nels may be skipped due to a weak signal. You can  
manually add the channel in the VCR memory. (Of  
course, you can later delete the added channel from the  
memory again.)  
1
Select main menu by press-  
- M E N U -  
ing the MENU button.  
TIMER PROGRAMMING  
AUTO REPEAT  
CHANNEL SET UP  
CLOCK SET  
[OFF]  
B
LANGUAGE SELECT  
AUDIO OUT  
TV STEREO  
SAP  
2
Select "CHANNEL SET UP"  
by pressing the PLAY or STOP  
button. Then, press the F.FWD  
button.  
[ON]  
1 Select main menu by press-  
- M E N U -  
ing the MENU button.  
TIMER PROGRAMMING  
AUTO REPEAT  
CHANNEL SET UP  
CLOCK SET  
[OFF]  
3
Select "AUTO SET UP" by  
pressing the PLAY or STOP  
button. Then, press the F.FWD  
button. After scanning, the  
tuner stops at the lowest memo-  
rized channel.  
B
CHANNEL SET UP  
——————————————————  
2 Select "CHANNEL SET UP"  
by pressing the PLAY or STOP  
button. Then, press the F.FWD  
button.  
LANGUAGE SELECT  
AUDIO OUT  
TV STEREO  
[ON]  
B
AUTO SET UP  
SAP  
MANUAL SET UP  
The VCR distinguishes between standard TV chan-  
nels and cable channels.  
3 Select "MANUAL SET UP"  
by pressing the PLAY or STOP  
button. Then, press the F.FWD  
button.  
CHANNEL SET UP  
——————————————————  
AUTO SET UP  
B
MANUAL SET UP  
SELECTING THE ON SCREEN  
LANGUAGE  
1
Select main menu by press-  
- M E N U -  
ing the MENU button.  
TIMER PROGRAMMING  
AUTO REPEAT  
CHANNEL SET UP  
CLOCK SET  
[OFF]  
4 Enter the desired channel  
number by pressing the  
PLAY or STOP button.  
B
LANGUAGE SELECT  
AUDIO OUT  
TV STEREO  
SAP  
2
Select "LANGUAGE SE-  
LECT" by pressing the  
PLAY or STOP button. Then,  
press the F.FWD button.  
MANUAL SET UP  
———————————————  
[ON]  
CHANNEL 30 ( TV )  
DELETE  
3
Select the On Screen Lan-  
guage ("ENGLISH" or  
"ESPAÑOL") bypressing the  
LANGUAGE SELECT  
——————————————  
B
ENGLISH  
[ON]  
5 Add or Delete it from memory by pressing the  
F.FWD or REW button so that "ADD" or "DELETE"  
flashes on the TV screen accordingly.  
ESPAÑOL  
PLAY or STOP button.  
MANUAL SET UP  
———————————————  
MANUAL SET UP  
———————————————  
CHANNEL 30 ( TV )  
DELETE  
CHANNEL 30 ( TV )  
ADD  
4
Exit the preset mode by pressing the RESET/EXIT  
button.  
- DELETED -  
- MEMORIZED -  
6
Exit the preset mode by pressing the RESET/EXIT  
button.  
Download from Www.Somanuals.-co8m-. All Manuals Search And Download.  
EN  
0J01  
PLAYBACK FUNCTION  
NORMAL PLAYBACK  
SEARCH FUNCTIONS  
1 Insert the prerecorded tape. The  
VCR will turn on. If the safety tab  
has been removed, the VCR will  
start playback automatically.  
PICTURE SEARCH  
If you want to skip or repeat a scene while in the play  
mode, press the F.FWD or REW button.  
Press it again and the VCR will now search in super  
high speed. (in the LP / SLP modes only)  
2 Turn on the TV and set the TV to channel 3 or 4.  
Now set the CH3/CH4 switch on the back of the VCR  
to match the channel selected on the TV.  
TIME SEARCH  
You can skip a program for a desired length of time.  
3 Begin playback by pressing the PLAY button.  
1) Press the SEARCH MODE  
Tracking adjustment will be set automatically (Digi-  
tal Tracking function) when you start playback. To  
adjust the tracking manually, press the CHANNEL  
Up or Down button on the VCR.  
When a tape has reached the end, the VCR will re-  
wind the tape to the beginning, eject the tape, and turn  
off the VCR automatically.  
TIME SEARCH  
2 : 5 0  
button so that the Time  
Search menu appears.  
2) Enter your desired time to  
skip by pressing the PLAY or  
STOP button within 30 sec-  
onds.  
3) Press the F.FWD or REW button to start time search.  
If you want to go in the forward direction, press the  
F.FWD button. If you want to go in the reverse di-  
rection, press the REW button.  
S-VHS Quasi Playback (SQPB)  
This unit allows you to view a tape recorded in S-VHS  
format. (Noise lines may appear on the picture.)  
4 To stop playback, press the STOP button.  
After time search, the VCR will play the tape auto-  
matically.  
STILL/SLOW  
1) You can freeze the picture on TV screen by pressing  
INDEX SEARCH  
The index signal is recorded on the tape automatically  
when the recording is started. If you want to view a re-  
the PAUSE/STILL button during playback.  
You can advance the picture by one frame at a time  
by pressing the PAUSE/STILL button during the still cording at a specific start point, it can easily be done.  
mode.  
1) Press the SEARCH MODE  
button so that the Index  
Search menu appears.  
INDEX SEARCH  
03  
2) You can see the slow motion by pressing the SLOW  
button during playback or the still mode.  
If the noise bar appears on the TV screen, you can re- 2) Enter your desired number by  
duce it by pressing the CHANNEL Up or Down button.  
pressing the PLAY or STOP  
button within 30 seconds.  
After the VCR has been in Still/Slow mode for 5 min-  
utes, it will stop automatically to protect the tape and  
the video head.  
3) Press the F.FWD or REW button to start index  
search. If you want to go in the forward direction,  
press the F.FWD button. If you want to go in the  
reverse direction, press the REW button.  
To return playback, press the PLAY button.  
AUTO REPEAT PLAYBACK  
Use this feature allows you to play a tape over and over.  
After index search, the VCR will play the tape auto-  
matically.  
1) Select main menu by pressing the MENU button.  
2) Select "AUTO REPEAT" by pressing the PLAY or  
STOP button.  
3) Begin auto repeat playback by pressing the F.FWD  
button so that [ON] will appear next to "AUTO RE-  
PEAT" on the TV screen.  
If the on-screen menu still remains, press the RE-  
SET/EXIT button to exit the menu.  
To cancel the auto repeat mode, press the F.FWD  
button at step [3] so that [OFF] appear next to  
"AUTO REPEAT" on the TV screen.  
When you set the auto repeat mode to [ON] while the  
counter memory mode is ON, the VCR will exit the  
counter memory mode automatically.  
Download from Www.Somanuals.-co9m-. All Manuals Search And Download.  
EN  
0J01  
RECORDING FUNCTION  
Before recording, make sure:  
1] Press the MENU button and select "TV STEREO" or  
"SAP" by pressing the PLAY or STOP button. Then,  
press the F.FWD button so that [ON] appears next to  
your desired item on the TV screen. To exit, press the  
RESET/EXIT button.  
Although a program may be broadcast in both stereo  
and second audio, you must select the recording mode  
in TV STEREO or SAP before you record a broadcast.  
The desired channel is selected by pressing the num-  
ber buttons on the remote control or the CHANNEL  
Up/Down button. (If you connected the VCR to a  
cable box or satellite box as in "Basic connections"  
on page 6, select the VCR to channel 3 or 4 the same  
channel as the CH3 or CH4 switch on the back of the  
VCR. Then, select the channel you want to record at  
the cable box or satellite box. In this case, you can  
ONLY record and view the SAME channel. )  
2] Press the MENU button and select "AUDIO OUT"  
by pressing the PLAY or STOP button. Then, press  
the F.FWD button. Next, select "HIFI" or "MONO"  
by pressing the PLAY or STOP button. To exit, press  
the RESET/EXIT button.  
There is a tape with its safety tab into the VCR.  
The desired recording speed is selected in SP(stand-  
ard play) or SLP(super long play) mode by pressing  
the TAPE SPEED button on the VCR.  
While the VCR is set in HIFI stereo mode, HIFI appears on  
the TV screen. While the VCR is set in monaural(MONO)  
mode, HIFI disappears from the TV screen.  
Tape Speed  
Recording/Playback Time  
Type of tape  
T60  
T120  
T160  
SP mode  
1 hour  
3 hours  
2 hours  
6 hours  
2-2/3 hours  
8 hours  
MTS RECORDING/MONITOR MODE  
SLP mode  
Type of  
broadcast  
Display on STEREO/SAP  
Hi-Fi audio track  
(2-channel)  
Normal audio  
track  
TV STEREO or SAP is selected.  
the TV  
screen  
Selection  
L-channel  
R-channel  
Regular  
(monaural  
audio)  
-None-  
-Invalid-  
Mono  
L
Mono  
R
Mono  
L+R  
VIEWING AND RECORDING  
THE SAME PROGRAM  
Stereo  
broadcast  
STEREO  
SAP  
-Invalid-  
1) Begin the recording by pressing the RECORD button.  
Bilingual  
broadcast  
TV STEREO* Main audio  
program  
Main audio  
program  
Main audio  
program  
To temporarily stop recording or resume it, press the  
SAP*  
Sub audio  
program  
Sub audio  
program  
Sub audio  
program  
PAUSE/STILL button. After the VCR has been in  
Pause mode for 5 minutes, it will stop automatically  
to protect the tape and the video head.  
Stereo &  
Bilingual  
broadcast  
STEREO  
SAP  
TV STEREO*  
SAP*  
L
R
L+R  
Sub audio  
program  
Sub audio  
program  
Sub audio  
program  
2) Stop the recording by pressing the STOP button  
when recording is completed.  
* You must select the recording mode in TV STEREO or SAP before you record a broadcast.  
COPYING A VIDEO TAPE  
You can make copies of video tapes made by friends or  
relatives for your enjoyment.  
Warning:Unauthorized recordings of copyrighted  
video tapes may be an infringement of copyright laws.  
OTR(One Touch Recording)  
This function enables you to set the recording length sim-  
ply by pressing the REC/OTR button on the VCR.  
1) Begin OTR by pressing the REC/OTR button on the  
VCR repeatedly until the desired recording length  
appears.  
Connect the recording VCR(this unit), the playing VCR(an-  
other source) and your TV using the following diagram.  
[TV set]  
(Use for monitoring)  
Recording stops when 0:00 is reached.  
Audio/Video cables  
(not supplied)  
[Recording VCR]  
(this unit)  
Press  
Display  
Recorded Length  
1 press  
(normal recording)  
ANT  
AUDIO  
L
IN  
Coaxial cable  
(supplied)  
IN  
OUT  
OUT  
2 presses  
3 presses  
0:30  
1:00  
30 minutes  
60 minutes  
LEFT RIGHT  
R
IN  
VIDEO  
VIDEO  
OUT  
AUDIO  
ANT in  
CH3 CH4  
IN  
OUT  
[Playing VCR]  
(another source)  
17 presses  
8:00  
480 minutes  
1) Insert a pre-recorded tape into the playing VCR.  
2) Insert a tape with its safety tab into the recording VCR.  
18 presses  
(normal recording)  
MTS (Multi-Channel Television  
Sound) SYSTEM  
When you play a VHS tape, or receive a broadcast on  
the VCR tuner channel you are watching, the status  
shown below will appear when you press the DISPLAY  
button on the remote control. When you record the MTS  
broadcast signal, you need setting MTS mode.  
3) Press the TAPE SPEED button on therecording VCR  
to select the desired recording speed (SP/SLP).  
4) Select the "L1" or "L2"position on the recording VCR.  
See page 6, under "Using audio/video input jacks".  
5) Press the REC/OTR button on the recording VCR.  
6) Begin playback of the tape in the playing VCR.  
For best results during dubbing, use the VCRs front  
panel controls whenever possible. The remote con-  
STOP  
12:00AM  
CH 32  
STEREO  
SAP  
trol might affect the playing VCRs operation.  
1]  
2]  
Always use video-quality shielded cables with RCA-  
type connectors. Standard audio cables are not rec-  
ommended.  
SP  
0:00:00  
HIFI  
Download from Www.Somanuals-.c1om0.-All Manuals Search And Download.  
EN  
0J01  
You can use a video disc player, satellite receiver, or  
other audio/video component with A/V outputs in  
place of the playing VCR.  
TO MONITOR THE RECORDING  
1) Turn on the TV and set the TV to channel 3 or 4. Now  
set the CH3/CH4 switch on the back of the VCR to  
match the channel selected on the TV.  
2) Press the VCR/TV button on the recording VCR so  
that the VCR/TV indicator comes on.  
TIMER RECORDING  
YoumaysettheVCRtostartrecordingwhileyouareaway.  
You can set seven programs to record on specific days,  
daily or weekly within a 1 year period.  
1) Insert a tape with its safety tab into the VCR.  
2) Select main menu by pressing the MENU button.  
HINTS FOR TIMER  
RECORDING  
If there is a power failure or the VCR is unplugged  
for more than 30 seconds, the clock setting and all  
timer settings will be lost.  
3) Select "TIMER PROGRAMMING" by pressing the  
PLAY or STOP button. Then, press the F.FWD button.  
If the tape runs out before the end time, the VCR will  
switch to the Stop mode immediately, eject the tape  
and the VCR power will be turned off. The TIMER  
indicator will flash.  
If you have not yet set the clock, "CLOCK SET" ap-  
pears. If so, follow the steps [3] and [4] in "CLOCK  
SET UP " section. Then, set the timer recording.  
If a tape is not in the VCR or does not have the safety  
tab, the TIMER indicator flashes and timer recording  
cannot be performed. Please insert a recordable tape.  
4) Set the timer.  
Set the program number (1~7)  
PROGRAM NUMBER  
4
DATE  
START TIME  
END  
CHANNEL  
- - / -  
- - : - - - -  
- - : - - - -  
- -  
Program number which is not set up flashes.  
Press the PLAY or STOP button repeatedly  
for the desired program number.  
TIME  
TO STOP AN AUTOMATIC TIMER  
PROGRAM ALREADY STARTED  
REC SPEED  
- -  
Then, press the F.FWD button.  
Select once, daily or weekly recording  
For once: Press the PLAY or STOP button  
to point to "ONCE".  
For daily (Monday~Friday):  
Press the PLAY or STOP button  
to point to "DAILY".  
For weekly: Press the PLAY or STOP  
button to point to "WEEKLY".  
Then, press the F.FWD button.  
Press the STOP/EJECT button on the VCR.  
TO CHECK, CORRECT, OR CANCEL AN  
AUTOMATIC TIMER PROGRAM  
1) Turn the power on.  
2) Select main menu by pressing the MENU button.  
3) Select "TIMER PROGRAMMING" by pressing the  
PLAY or STOP button. Then, press the F.FWD button.  
4) Select the program number which you want to check  
by pressing the PLAY or STOP button. The details  
of the selected program appears on the TV screen.  
PROGRAM NUMBER  
4
ONCE  
DAILY  
WEEKLY  
Set the date  
First, press the PLAY or STOP button for the month,  
then, press the F.FWD button.  
Next, press the PLAY or STOP button for the day.  
Then, press the F.FWD button.  
Set the start time  
First, press the PLAY or STOP button for the hour,  
then, press the F.FWD button.  
Next, press the PLAY or STOP button for the minute,  
then, press the F.FWD button.  
And then, press the PLAY or STOP button for AM or PM.  
Then, press the F.FWD button.  
Set the end time  
Follow the instructions of "Set the start time"  
to set the end time.  
Go to the digit you want to change by pressing the  
F.FWD or REW button. Then, enter correct num-  
bers by pressing the PLAY or STOP button.  
You may cancel the entire program by pressing the  
REW button during the program number flashes.  
5) Press the RESET/EXIT button to exit.  
6) Press the POWER button to return to timer stand-  
by mode.  
Set the channel number  
Press the PLAY or STOP button repeatedly  
AVOIDING OVERLAPPING PROGRAMS  
There may be times when a program will not record.  
When programs overlap:  
for the desired channel number.  
Then, press the F.FWD button.  
If you connected the VCR to a cable box or satellite box as in  
"Basic connections" on page 6, select the VCR to channel 3  
or 4 the same channel as the CH3 or CH4 switch on the back  
of the VCR. Then, select the channel you want to record at  
the cable box or satellite box. Leave the cable box or satellite  
The program with the earliest start time has priority.  
Once the earliest program finishes, the overlapping  
program with the lower number will begin recording  
in sequence.  
box on for timer recording.  
ONE TIME PROGRAM  
PROGRAM NUMBER  
4
Set the tape speed  
Press the PLAY or STOP button repeatedly  
for the desired tape speed.  
DATE  
START TIME  
END  
CHANNEL  
05/03 THU  
07:30 PM  
08:30 PM  
16  
TIME  
The illustration below demonstrates the sequence of  
recordings.  
REC SPEED  
SP  
SP  
SLP  
Then, press the F.FWD button.  
Recording Sequence  
To go back one step, press the REW button.  
Program 1  
5) To set another program, repeat step [4]. To exit, press  
the RESET/EXIT button.  
6) Press the POWER button to set the timer. The TIMER  
indicator on the VCR comes on.  
(10:00AM-11:00AM)  
Program 2  
(9:00AM-10:00AM)  
Program 3  
(9:30AM-12:00PM)  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
Download from Www.Somanuals-.c1om1.-All Manuals Search And Download.  
EN  
0J01  
SPECIAL FEATURES  
COUNTER MEMORY FUNCTION  
Use this feature to memorize the beginning of recording  
start point.  
AUTO REWIND  
When a tape has reached the end during recording, play-  
back, or fast-forward, the tape will automatically rewind  
to the beginning. After rewinding finishes, the VCR will  
eject the tape and turn itself to off.  
1) Press the COUNTER RE-  
REC  
SET button on the remote  
control to reset the counter.  
The tape will not auto-rewind during timer recording  
or One Touch Recording.  
When the Counter Memory is activated, the tape will  
rewind to the M0:00:00 and the VCR will go into the  
Stop mode.  
2) Press the COUNTER  
MEMORY button on the  
SP  
M
0:00:00  
remote control so that "M"  
appears on the TV screen.  
3) Record the program.  
REAL TIME TAPE COUNTER  
This shows the elapsed recording or playback time in  
hours, minutes, and seconds. (The displayed time  
will not change during blank portions on the tape.)  
The "" indication will appear when the tape is re-  
wound further than "0:00:00" on the tape counter.  
4) After recording, press the STOP button then the  
REW button.  
When "0:00:00" is reached, rewinding operation  
goes to stop. And you can view the recording pro-  
gram.  
The COUNTER MEMORY button does not function  
if the auto repeat mode is set to [ON]. In this case, set  
the auto repeat mode to [OFF].  
To cancel the counter memory mode, press the  
COUNTER MEMORY button so that "M" disap-  
pears from the TV screen.  
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate  
the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy  
the problem.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the VCR clock is set correctly.  
Make sure the tape has a safety tab. If needed, cover the hole with  
plastic tape.  
No power.  
Timer recording is not possible.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
Adjust tracking control for a better picture by pressing the  
CHANNEL Up or Down button on the VCR.  
Head cleaning may be necessary. Refer to "AUTO HEAD  
CLEANING" .  
Cannot view a tape but the audio is  
OK.  
Make sure the VCR is not in the Menu mode.  
Set your TV to the VCR mode and/or press the VCR/TV button so that  
the VCR/TV indicator on the VCR comes on.  
No picture or poor picture on  
playback.  
Fine tune your TV.  
Re-check the ANT. IN and ANT. OUT connections. See page 6.  
Set your TV to the TV mode and/or press the VCR/TV button so that  
the VCR/TV indicator on the VCR disappears.  
On-the-air TV programs cannot be  
seen.  
No VCR operation from the infrared  
Remote Control.  
Make sure the power plug is connected to an AC outlet.  
Check batteries in remote control.  
You cannot copy a copyrighted video tape. You are experiencing  
copy guard protection.  
Video or color fades in and out when  
making a copy of a video tape.  
Download from Www.Somanuals-.c1om2.-All Manuals Search And Download.  
EN  
0J01  
SPECIFICATIONS  
Television system :  
Video heads :  
Tape cassette :  
Tape speed  
Recording :  
Playback :  
Tuner channel  
NTSC, TV standard  
Rotary four-head  
Video output level :  
Video output impedance : 75Ω  
1Vp-p  
Audio output level :  
Video input level :  
Audio input level :  
Power requirement :  
Power consumption :  
Dimensions :  
-6dBv (1KHz)  
0.5~2.0Vp-p  
-10dBv  
120V, 60Hz  
14 Watts  
video cassette  
SP, SLP  
SP, LP, SLP  
W
H
14-1/4" (360mm)  
3-5/8" (92mm)  
VHF :  
UHF :  
#2~#13  
#14~#69  
D
8-1/2" (215.5mm)  
Cable channel :  
RF converter :  
Converter output :  
Timer indication :  
Operating temperature : 5 C~40 C (41 F~104 F)  
Terminals  
5A, A-5 ~ A-1, A ~ W+84  
Built-in VHF converter  
VHF Channel 3 or 4.  
AM/PM 12-hour system  
Weight :  
5.3 lbs. (2.4 Kg.) (approx.)  
Designs and specifications are subject to change  
without notice and without legal obligation.  
o
o
o
o
If there is a discrepancy between languages, the de-  
fault language will be English.  
Antenna input :  
Antenna output :  
Video input/output :  
F type connector x 1  
F type connector x 1  
RCA connector x 3  
Audio input/output : RCA connector x 6  
MAINTENANCE  
SERVICING  
AUTO HEAD CLEANING  
Should your VCR become inoperative, do not try to cor-  
rect the problem by yourself. There are no user-service-  
able parts inside. Turn off, unplug the power plug, and  
please call our help line at 1-800-968-3429, to locate an  
Authorized Service Center.  
Automatically cleans video heads as you insert or re-  
move a cassette, so you can see a clear picture.  
Playback picture may become blurred or interrupted  
while the TV program reception is clear. Dirt accu-  
mulated on the video heads after long periods of use,  
or the usage of rental or worn tapes can cause this  
problem.  
CABINET CLEANING  
If a streaky or snowy picture appears during play-  
back, the video heads in your VCR may need to be  
cleaned.  
Wipe the front panel and other exterior surfaces of  
the VCR with a soft cloth immersed in lukewarm  
water and wrung dry.  
1. Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2. If a Video Head Cleaner does not solve the problem,  
please call our help line at 1-800-968-3429, to locate  
an Authorized Service Center.  
Never use a solvent or alcohol. Do not spray insecti-  
cide liquid near the VCR. Such chemicals may cause  
damage and discoloration to the exposed surfaces.  
NOTES:  
Remember to read the instructions included with the  
video head cleaner before use.  
Clean video heads only when problems occur.  
Download from Www.Somanuals-.c1om3.-All Manuals Search And Download.  
EN  
0J01  
CONEXIONES DE ANTENA/TELEVISIÓN POR CABLE  
Para conocer algunos de los tipos de conexión más comunes, consulte 3. Conecte un extremo del cable coaxial (suministrado) a ANT.OUT  
las explicaciones siguientes. Utilice solamente una conexión. Para ha-  
cer conexiones más complejas, consulte a su concesionario local. (Tal  
vez necesite accesorios adicionales que no han sido incluidos.)  
(toma inferior) de su videograbadora.  
4. Conecte el otro extremo del cable coaxial (suministrado) a la toma  
de antena UHF/VHF de su televisor.  
NOTA: Para obtener más información, consulte la sección "Conexio- 5. Si su televisor no tiene terminales A/V: Ponga el conmutador se-  
nes de antena/televisión por cable" en la página 6.  
lector en CH3 o CH4 (en la parte trasera de su videograbadora), el  
que no se utilice para las  
1. Desconecte la antena o la caja de televisión por cable de su tele-  
visor.  
2. Conecte la antena o la caja de televisión por cable a ANT.IN (toma  
superior) de su videograbadora.  
emisiones normales en su  
zona. Luego ajuste el televi-  
OUT  
CH3  
CH4  
CH3 CH4  
sor al mismo canal.  
[Parte trasera de la videograbadora]  
[Caja de televisión por cable o caja de emisiones de satélite]  
Conexiones básicas  
OUT  
IN  
De empresa  
de televisión  
por cable o  
ANT  
AUDIO  
L
de emisiones  
O
IN  
de satélite  
IN  
OUT  
R
Antena  
interior o  
exterior  
VIDEO  
OUT  
Cables de audio/vídeo  
(no suministrado)  
Cable coaxial  
(suministrado)  
CH3 CH4  
IN  
OUT  
O
De empresa  
de televisión  
por cable  
Parte trasera de  
la videograbadora  
(Ninguna caja  
de televisión  
por cable)  
IN  
R
IN  
L
AUDIO  
VIDEO  
O
VHF  
UHF  
VHF  
UHF  
O
ANT in  
EQUIPO ESTÉREO  
Terminal TV A/V  
Terminal de antena del televisor  
PREPARACIÓN DE CANALES  
(La antena o la caja de televisión por  
cable deberá estar conectada)  
PREPARACIÓN DEL RELOJ  
1. Pulse el botón MENU hasta que aparezca el menú principal.  
(Si el reloj no está puesto en hora y se pulsa el botón MENU, el  
menú AJUSTE DE RELOJ aparece en primer lugar. En este caso,  
siga el paso 3.)  
2. Pulse el botón PLAY o STOP para indicar a "AJUSTE DE RE-  
LOJ". Luego, pulse el botón F.FWD.  
NOTA: Cuando utilice su nueva videograbadora por primera vez, o  
en el caso de ser necesario después de producirse un fallo en la ali-  
mentación, la videograbadora se pondrá inicialmente en el modo de  
preajuste cuando se pulse el botón POWER.  
Si conecta una caja de televisión por cable o una caja de emisiones vía  
satélite, consulte la sección "Preparación automática de canales" del  
manual del propietario.  
1. Encienda el televisor y ponga el televisor en el canal 3 ó 4. Ahora  
ponga el conmutador de la parte trasera de la videograbadora para  
que concuerde con el canal seleccionado en el televisor.  
3.  
Ajuste el mes.  
Ajuste el día.  
Ajuste el año.  
Ajuste la ora.  
Ajuste el minuto.  
Pulse repetidamente el botón PLAY o STOP.  
Luego, pulse el botón F.FWD.  
Pulse repetidamente el botón PLAY o STOP.  
Luego, pulse el botón F.FWD.  
Pulse repetidamente el botón PLAY o STOP.  
Luego, pulse el botón F.FWD.  
2. Pulse el botón POWER para encender la video-  
SELEC. IDIOMA  
Pulse repetidamente el botón PLAY o STOP.  
Luego, pulse el botón F.FWD.  
——————————————  
grabadora.  
ENGLISH  
3. Seleccione "ENGLISH" o "ESPAÑOL" (Spa-  
B ESPAÑOL [ON]  
Pulse repetidamente el botón PLAY o STOP.  
Luego, pulse el botón F.FWD.  
nish) pulsando el botón PLAY o STOP. Y luego  
pulse el botón F.FWD.  
AJUSTE DE RELOJ  
Pulse repetidamente  
el botón PLAY o STOP.  
4. Pulse una vez el botón F.FWD.  
Ajuste la  
mañana (AM) o  
la tarde (PM).  
MES  
0 3  
DIA  
1 9  
AÑO  
LUN 2001  
El sintonizador explora y memoriza todos los canales activos de  
su zona. Tras la exploración, el sintonizador se detiene en el canal  
memorizado más bajo.  
/
HORA MINUTO  
05 40  
AM/PM  
PM AM  
PM  
:
Para volver atrás un paso, pulse el botón REW.  
4. Después de establecer AM o PM, pulse el botón RESET/EXIT o  
F.FWD para poner en funcionamiento el reloj.  
Download from Www.Somanuals-.c1om4.-All Manuals Search And Download.  
ES  
0J01  
CONTROLES DE FUNCIONAMIENTO Y FUNCIONES  
2
4
5
6
1
3
PANEL DELANTERO  
MANDO A DISTANCIA  
STOP/EJECT  
PLAY  
DE LA VIDEOGRABADORA  
REW  
F.FWD  
POWER  
VCR/TV EJECT  
3
7
3
8
12  
REC/OTR  
PAUSE/STILL  
1
2
5
8
0
VIDEO  
L
AUDIO  
R
TAPE IN  
TIMER  
REC  
POWER  
VCR/TV  
MENU  
CHANNEL  
6
4
7
15  
9
8
26 23  
21  
7
9
10  
11  
12  
22  
13  
14  
MENU  
+100 SEARCH MODE  
20  
19  
18  
4
14  
16  
17  
PANEL TRASERO DE LA  
VIDEOGRABADORA  
DISPLAY SLOW EXIT COUNTER  
23 24  
MEMORY  
PLARYESET  
REW  
F.FWD  
AUDIO  
L
ANT  
IN  
2
3
5
6
OUT IN  
R
STOP  
PAUSE/STILL  
RECORD  
VIDEO  
OUT  
13  
OUT INCH3  
CH4  
25 26 27 28  
1. Compartimiento del videocasete  
12. Botones de selección de canales (CHANNEL) - Púlselos para se-  
leccionar los canales deseados para ver o grabar.  
2. Botón de rebobinado (REW) - Púlselo para rebobinar la cinta o para  
ver rápidamente la imagen en retroceso durante el modo de reproducción.  
(Búsqueda con rebobinado)  
Púlselo para cancelar un ajuste de programa de temporizador. Púlselo para  
corregir los dígitos al programar (por ejemplo: puesta en hora del reloj o un  
programa de temporizador). Púlselo para añadir o borrar números de canales  
durante el preajuste de canales.  
Función de seguimiento – Pulse los botones para minimizar el "ruido"  
de vídeo (líneas o puntos en la pantalla) durante la reproducción (sólo en la  
videograbadora) o el modo de cámara lenta.  
Púlselo para estabilizar la imagen en el modo de imagen fija cuando ésta  
empieza a vibrar verticalmente.  
13. Botón de grabación (RECORD) - Púlselo para realizar la grabación  
manual.  
3. Botón de expulsión (EJECT) - Púlselo para sacar el videocasete de la  
videograbadora.  
Botón de grabación con un toque (OTR) - Púlselo para activar la  
grabación con un toque. (Sólo en la videograbadora)  
14. Botón de menús (MENU) - Púlselo para visualizar los menús en la pan-  
talla del televisor. Y vuelva a pulsarlo para salir de los menús de la pantalla  
del televisor.  
Botón de parada (STOP) - Púlselo para detener la cinta.  
Púlselo para introducir los dígitos cuando establezca programas (por ejem-  
plo: puesta en hora del reloj o un programa de temporizador). Púlselo para  
seleccionar los modos de ajuste en el menú en pantalla.  
4. Botón de reproducción (PLAY) - Púlselo para iniciar la reproducción.  
Púlselo para introducir los dígitos cuando establezca programas (por ejem-  
plo: puesta en hora del reloj o un programa de temporizador).  
Púlselo para seleccionar los modos de ajuste en el menú en pantalla.  
5. Botón de avance rápido (F.FWD) - Púlselo para avanzar rápidamente  
la cinta o para ver rápidamente la imagen en avance durante la reproducción.  
(Búsqueda en avance)  
15. Botones de números (NUMBER) - Púlselos para seleccionar los cana-  
les deseados para ver o grabar. Para seleccionar los canales del 1 al 9, pulse  
primero el botón "0" y luego el botón 1 a 9. (Sólo en el mando a distancia)  
Botón +100 - Cuando seleccione canales de televisión por cable cuyo nú-  
mero sea superior al 99, pulse primero este botón, y luego pulse los dos  
últimos dígitos. (Para seleccionar el canal 125, pulse primero el botón  
"+100" y luego el "2" y el "5".) (Sólo en el mando a distancia)  
Cuando establezca un programa (por ejemplo: puesta en hora del reloj o un  
programade temporizador), púlselo para determinar su selección yproseguir  
con el siguiente paso que desee introducir. Púlselo para determinar los mo-  
dos de ajuste del menú en pantalla. Púlselo para añadir o borrar números de  
canales durante el preajuste de canales.  
6. Botón de pausa/imagen fija (PAUSE/STILL) - Púlselo para detener  
temporalmente la cinta durante la grabación o para ver una imagen fija du-  
rante la reproducción.  
16. Botón del visualizador (DISPLAY) - Púlselo para visualizar en la pan-  
talla del televisor la hora actual, el número del canal, el contador de cinta en  
tiempo real y otra información. (Sólo en el mando a distancia)  
Cada vez que pulse este botón, la pantalla del televisor cambiará. La visua-  
lización del estado (PARAR, REPRODUCIR, etc.) y la visualización de  
velocidad de la cinta [SP, LP (reproducción solamente) o SLP] desaparecerá  
después de 5 segundos.  
17. Botón de cámara lenta (SLOW) - Púlselo para iniciar la reproducción  
de cámara lenta. (Sólo en el mando a distancia)  
18. Botón de memoria del contador (COUNTER MEMORY) - P ú l s e l o  
para activar y desactivar lamemoriadelcontador. (Sólo en el mando adistancia)  
19. Botón de reposición del contador (COUNTER RESET) - Púlselo  
para reponer el contador a 0:00:00. (Sólo en el mando a distancia)  
Función de avance de cuadro - Púlselo paraavanzar laimagencuadro  
a cuadro durante el modo de imagen fija.  
7. Botón de la alimentación (POWER) - Púlselo para encender y apagar  
la videograbadora. Púlselo para activar la grabación con temporizador cuan-  
do ésta haya sido establecida.  
8. Botón de videograbadora/televisor (VCR/TV) - Púlselo para selec-  
cionar el modo de la videograbadora (VCR) o del televisor (TV).  
PosiciónVCR:para ver la reproducción, comprobarlasgrabacionesdevídeo  
o ver programas de TV utilizando el sintonizador de la videograbadora.  
Posición TV: para ver programas de TV o para ver un programa mientras se  
graba otro.  
9. Ventanilla sensora del mando a distancia - Recibe las señales in-  
frarrojas procedentes del mando a distancia.  
10. Indicadores  
Botón de salida (EXIT) - Púlselo para salir de los menús en pantalla.  
(Sólo en el mando a distancia)  
20. Botón del modo de búsqueda (SEARCH MODE) - Púlselo para re-  
alizar una búsqueda con tiempo o una búsqueda con índice. (Sólo en el  
mando a distancia)  
21. Cable de alimentación - Conéctelo a una toma de CA estándar (120  
V/60 Hz).  
22. Tomas de salida de audio (AUDIO OUT) - Conéctelas a las tomas de  
entrada de audio de su equipo de audio o de otra videograbadora.  
23. Tomas de entrada de audio (AUDIO IN) - Conéctelas a las tomas de  
salida de audio de su equipo de audio o de otra videograbadora.  
24. Terminal de entrada de antena (ANT. IN) - Aquí se conecta una ante-  
na, sistema de televisión por cable o sistema de emisiones vía satélite.  
25. Toma de salida de vídeo (VIDEO OUT) - Conéctela a la toma de en-  
trada de vídeo de su videocámara o de otra videograbadora.  
26. Toma de entrada de vídeo (VIDEO IN) - Conéctela a la toma de salida  
de vídeo de su videocámara o de otra videograbadora.  
Indicador de alimentación (POWER) - Indica que la alimentación  
está conectada.  
Indicador de videograbadora/televisor (VCR/TV) - Indica quelavi-  
deograbadora está activada.  
Indicador de videocasete introducido (TAPE IN) - Indica que hay  
un videocasete en la videograbadora.  
Indicador del temporizador (TIMER) - Indica que ha sido establecida  
la grabación con temporizador u OTR.  
27. Conmutador selector de canales CH3/CH4 - Se utiliza para seleccio-  
naruncanaldesalidadevídeo(3 ó4)paralareproduccióndelavideograbadora.  
28. Terminal de salida de antena (ANT. OUT) - Conéctelo al terminal de  
entrada de la antena de su televisor.  
Indicador de grabación (REC) - Indica que la videograbadora está gra-  
bando. Parpadea cuando la grabación ha hecho una pausa.  
11. Botón de velocidad de cinta (TAPE SPEED) - Púlselo para elegir la  
velocidad de grabación deseada: SP/SLP. (Sólo en la videograbadora)  
Download from Www.Somanuals-.c1om5.-All Manuals Search And Download.  
ES  
0J01  
LIMITED WARRANTY  
Funai Corporation will exchange or repair this product, at its option, in the event of defect in materials or workmanship as follows:  
EXCHANGE DURATION:  
1-90 DAYS:  
FUNAI CORPORATION will exchange for a new unit without change for a period of ninety (90)  
days from the date of original retail purchase.  
91-365 DAYS: FUNAI CORPORATION will exchange for a factory-service-to-new-condition unit for a charge of  
$49.00 for the period of ninety one (91) days to three hundred sixty five (365) days from the date of  
original retail purchase.  
REPAIR DURATION:  
LABOR:  
FUNAI CORPORATION will provide the labor without charge for a period of ninety (90) days from  
the date of original retail purchase.  
PARTS:  
FUNAI CORPORATION will provide parts to replace defective parts without charge for a period of  
one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts  
are excluded from this warranty.  
LIMITS AND EXCLUSIONS:  
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be  
required together with the product to obtain exchange or service under this warranty.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced or missing. This SYLVANIA  
Limited warranty applies only to product purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship, which occur during normal use. It does not cover damage  
which occurs in shipment, or failures which are caused by repairs, alterations, or parts not supplied by FUNAI CORPORATION, or  
damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance,  
commercial use such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or other acts of  
God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL  
UNITS), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMONSTRATION OR FLOOR MODELS.  
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE  
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES INCLUDING  
THE WARRANTY OF MERCHANT ABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, THAT ARE HEREBY  
DISCLAIMED BY FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED CENTER. THIS  
WARRANTY IS VALID WHEN THE PRODUCT IS DELIVERED PREPAID TO A FUNAI AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY  
FROM STATE TO STATE, IF AT ANY TIME DURING THE WARRANTY PERIOD YOU ARE UNABLE TO OBTAIN  
SATISFACTION WITH THE EXCHANGE OR REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORPORATION.  
ATTENTION:  
FUNAI CORPORATION RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
For information about your product, or for information on how to exchange or repair your product,  
telephone or write to the following:  
FUNAI CORPORATION  
Customer Service  
100 North Street; Teterboro, NJ 07608  
Telephone (800)968-3429  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in China  
0VMN02761  
H7905UD ★★★★  
 

Shure Headphones psm400 User Manual
Silex technology Network Router SX ND4050G User Manual
Soleus Air Electric Heater HC6 15R 01 User Manual
Sonic Alert Clock SBJ525SS User Manual
Sony Car Stereo System FM User Manual
Sony Ericsson Cell Phone 1102101 BV User Manual
Sony VCR KV 13VM42 User Manual
Stamina Products Elliptical Trainer 15 4545 User Manual
Sunbeam Food Processor LC6250 User Manual
Tanaka Drill TED 210 User Manual