VIDEO CASSETTE
RECORDER
OWNER’S MANUAL
If you need additional
operating assistance after
reading this owner's manual
or to order replacement
accessories, please call
TOLL FREE : 1-800-968-3429.
6265FC
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING:
The lightning flash with arrowhead symbol, within
CAUTION
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of suffi-
cient magnitude to constitute a risk of electric
shock to persons.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instruc-
tions in the literature accompanying the product.
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1. Read Instructions- All the safety and operating instructions should be
read before the appliance is operated.
FIGURE A
ANTENNA
2. Retain Instructions- The safety and operating instructions should be
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
LEAD
WIRE
retained for future reference.
3. Heed Warnings- All warnings on the appliance and in the operating
instructions should be adhered to.
4. Follow Instructions- All operating and use instructions should be
followed.
5.Cleaning- Unplug this video product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that
for some specific reason, such as the possibility of the loss of an
authorization code for a CATV converter, is not intended to be unplugged
by the user for cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description otherwise
required in item 5.
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
NEC – NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
6. Attachments- Do not use attachments not recommended by the video
product manufacturer as they may cause hazards.
7.Water and Moisture- Do not use this video product near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and the like.
14. Lightning- For added protection for this video product during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system.This will prevent damage to the video product due to lightning
and power-line surges.
15. Power Lines- An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits.When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
8. Accessories- Do not place this video product on an unstable cart,
stand, tripod, bracket, or table.The video product may fall, causing
serious injury to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the
video product. Any mounting of the appliance should follow
the manufacturer's instructions and should use a mounting
accessory recommended by the manufacturer. An
16. Overloading- Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.
appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
17. Object and Liquid Entry- Never push objects of any kind into this video
product through any openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the video product.
18. Servicing- Do not attempt to service this video product yourself as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service- Unplug this video product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
9.Ventilation- Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the video product and to
protect it from overheating, and these openings must not be blocked or
covered.The openings should never be blocked by placing the video
product on a bed, sofa, rug, or other similar surface.This video product
should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions
have been adhered to .
10. Power Sources- This video product should be operated only from the
type of power source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your appliance dealer
or local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. Grounding or Polarization- This video product is equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other).This plug will fit into the power outlet only one way.This is
a safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician
to replace your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
12. Power Cord Protection- Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the appliance.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in performance-this
indicates a need for service.
20. Replacement Parts- When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other
hazards.
21. Safety Check- Upon completion of any service or repairs to this video
product, ask the service technician to perform safety checks to
determine that the video product is in proper operating condition.
13. Outdoor Antenna Grounding- If an outside antenna or cable system is
connected to the video product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig. A)
22. Heat- This video product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
PREPARATION FOR USE
1 Check contents
VCR to AV TV connection using AUDIO/VIDEO Cables
Make sure the package contains all of the accessories
listed in "as below".
Using Optional AUDIO/ VIDEO Output Jacks
With this connection, you can get better pictures and
sounds when playing back a tape if your TV has A/V
Input jacks. Please refer to your TV’s owner’s manual.
Using AUDIO/VIDEO Input Jacks
SUPPLIED ACCESSORIES
ACCESSORIES
Coaxial Cable
PART NO.
WPZ0901TM002
NA301UD/NA351UD
AA x 2
You can use the A/V input jacks on the front or the back
of the VCR.
Remote Control Unit
Batteries
• To use the input jacks on the back of the VCR, select
"L1" position by pressing [0], [0], [1] on the remote
(
)
control or [CHANNEL
].
• To use the input jacks on the front of the VCR, select
2 Situate VCR
"L2" position by pressing [0], [0], [2] on the remote
Place the VCR in a stable, horizontal surface.
(
)
control or [CHANNEL
].
3 Connect VCR to TV
“L1” or “L2” is found
before the lowest
memorized channel.
(Example: CH2)
[Playing VCR]
AUDIO
L
VCR to TV Connection
OUT
IN
IN
R
1. Disconnect the AC power cord of the TV from the AC
outlet.
VIDEO
Audio/Videocables
(not supplied)
OUT
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT. IN jack of
the VCR.
4. Connect the VCR to the TV using the coaxial cable.
5. Plug the AC power cords of the VCR and TV into the
AC outlets.
[TV A/V]
IN
L
R
VIDEO
AUDIO
SETTING THE CH3/CH4 SWITCH
[VHF/UHF
[Back of the VCR]
[Indoor antenna]
combination antenna]
[Back of the
If your TV does not have A/V terminals:
When the VCR is in the Playback mode or when the
VCR is in the VCR mode, your TV will receive signals
from the VCR on either channel 3 or 4. To use the VCR
with your TV, set the selector switch to CH3 or CH4
(which is located in the back of
UHF/VHF combination TV]
Coaxial cable
(supplied)
ANT
IN
OR
OR
UHF/VHF
[Cable box or satellite box]
OUT
IN
OUT
From Cable or
Satellite Company
your VCR), whichever is not
OUT
CH3
CH4
used for normal broadcasts in
your area. Then set your TV to
the same channel.
CH3 CH4
[Back of the VCR]
SETUP
AUTOMATIC CHANNEL SET UP
You can automatically program the tuner to scan only
the channels you receive in your area.
4 Select the On Screen Language
("ENGLISH" or "ESPAÑOL")
by pressing [PLAY] or [STOP]. Then, press
[F.FWD].
•
Channel memory programming is NOT needed when you
connected the VCR to a cable box or satellite box as in
"Connect VCR to TV". In this case, select the VCR and TV
to channel 3 or 4 the same channel as the CH3 or CH4
switch on the back of the VCR. Then, the channel you
want to record or view may be selected at the cable box or
satellite box.
Follow the steps below once. Repeat it only if there is a
power failure or if the VCR is unplugged for more than 30
seconds. (In these cases, the programmed channels are
erased.)
5Begin channel preset
CH 01
by pressing [F.FWD] once. The tuner scans
and memorizes all active channels in your
area.
AUTO SET UP
• The VCR distinguishes between standard
TV channels and cable channels.
•
6 After scanning,
the tuner stops on the lowest memorized channel. The TV
screen returns to TV mode.
• If "AUTO SET UP" appears on the TV screen again, check
the cable connections. Press [F.FWD] once again and the
VCR will begin preset again.
• You must follow the steps below before attempting to
play or record a video tape. If you want to play or
record a video tape BEFORE programming the tuner,
you can cancel it by pressing [EXIT/RESET].
T
O SELECT A DESIRED CHANNEL
1 You need to connect the antenna or cable to the VCR
first. Then, connect the VCR power plug into a
standard AC outlet.
You can select the desired channel by using [CHANNEL
(
control.
)
] or directly pressing [Number] on the remote
2 Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the VCR to
match the channel selected on the TV.
Note for using the Number buttons:
• When selecting cable channels which are higher than
99, press [+100] first, then press the last two digits.
•You must precede single-digit channel numbers with a
zero (For example: 02, 03, 04 and so on).
3 Turn on the VCR by pressing [POWER]. It comes on that
both the POWER and the VCR indicator.
EN
– 3 –
T
O PRESET THE CHANNEL AGAIN
PLAYBACK FUNCTION
1 Press [MENU] until the main menu appears.
NORMAL PLAYBACK
2 Select "CHANNEL SET UP" by pressing [PLAY] or
[STOP]. Then, press [F.FWD].
Insert the prerecorded tape. The
VCR will turn on. If the safety tab has
been removed, the VCR will start
playback automatically.
1
3 Select "AUTO SET UP" by pressing [PLAY] or
[STOP]. Then, press [F.FWD]. After scanning, the tuner
stops on the lowest memorized channel.
TO ADD/DELETE CHANNELS
Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the
VCR to match the channel selected on the TV.
2
3
When the VCR automatically program the tuner to scan
only the channels you receive in your area, some
channels may be skipped due to weak signal. You can
manually add the channel in the VCR memory.
1 Press [MENU] until the main menu
Begin playback by pressing [PLAY].
• Tracking adjustment will be set automatically (Digital
Tracking function) when you start playback. To adjust
(
)
the tracking manually, press [CHANNEL
] on
appears.
- MENU -
the VCR.
TIMER PROGRAMMING
2 Select "CHANNEL SET UP" by
pressing [PLAY] or [STOP]. Then,
press [F.FWD].
3 Select "MANUAL SET UP" by
pressing [PLAY] or [STOP]. Then,
press [F.FWD].
[OFF]
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
• When a tape has reached the end, the VCR will
rewind the tape to the beginning, eject the tape, and
turn off the VCR automatically.
LANGUAGE SELECT
AUDIO OUT
[ON]
TV STEREO
SAP
• S-VHS Quasi Playback (SQPB): This unit allows you
to view a tape recorded in S-VHS format. (Noise
lines may appear on the picture.)
4 Enter the desired channel number by pressing
[PLAY] or [STOP].
4
To stop playback, press [STOP].
5 Add or Delete it from memory by pressing [F.FWD]
or [REW] so that "ADD" or "DELETE" flashes on the
TV screen accordingly.
STILL/SLOW
You can freeze the picture on TV screen by pressing
[PAUSE/STILL] during playback.
6 Exit the Preset mode by pressing [EXIT/RESET].
• You can advance the picture by one frame at a time
by pressing [PAUSE/STILL] during the still mode.
• If the picture begins to vibrate vertically during the still
mode, stabilize the picture by pressing
TO CHANGE THE ON-SCREEN LANGUAGE
(
)
[CHANNEL
].
1 Press [MENU] until the main menu appears.
2 Select "LANGUAGE SELECT" by pressing [PLAY] or
[STOP]. Then, press [F.FWD].
3 Select "ENGLISH" or "ESPAÑOL" by pressing [PLAY]
or [STOP]. Then, press [EXIT/RESET].
• If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV, if equipped.
You can see the slow motion by pressing [SLOW]
during playback or the still mode.
• If the noise bar appears on the TV screen, you can
reduce it by pressing [CHANNEL
(
)
].
CLOCK SET UP
Set the clock accurately for proper automatic timer
recording. We suggest that you use a TV or radio
station as your time source.
• After the VCR has been in Still/Slow mode for 5
minutes, it will stop automatically to protect the tape
and the video head from damage.
• To return playback, press [PLAY].
1 Select main menu by pressing [MENU].
(If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].)
AUTO REPEAT PLAYBACK
2 Select "CLOCK SET" by pressing [PLAY] or
This feature allows you to play a tape over and over.
1 Select main menu by pressing [MENU].
2 Select "AUTO REPEAT" by pressing [PLAY] or
[STOP].
3 Begin auto repeat playback by pressing [F.FWD] so
that [ON] appears next to "AUTO REPEAT".
• If the on-screen menu still remains, press
[EXIT/RESET] to exit the menu.
[STOP]. Then, press [F.FWD].
3 Set the clock.
Set the month Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Set the day
Press [PLAY] or [STOP]repeatedly.
Then, press [F.FWD].
• To cancel the Auto repeat mode, press [F.FWD] at
step [3] so that [OFF] appears next to "AUTO
REPEAT".
Set the year
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
The day of the week will appear automatically.
• When you set the Auto repeat mode to [ON] while the
Counter memory mode is ON, the VCR will exit the
Counter memory mode automatically.
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Set the hour
Set the minute
SEARCH FUNCTIONS
Press [PLAY] or [STOP]
repeatedly.
Set the AM
or PM
CLOCK SET
PICTURE SEARCH
MONTH DAY
YEAR
03 18 MON 2002
/
If you want to skip or repeat a scene during playback,
press [F.FWD] or [REW].
HOUR MINUTE AM/PM
05
:
40
PM AM
PM
• Press it again and the VCR will now search in super
high speed. (in the LP/SLP modes only)
• To go back one step, press [REW].
4 Start the clock by pressing [EXIT/RESET] or
[F.FWD].
EN
– 4 –
INDEX SEARCH
TIME SEARCH
The index signal is recorded on the tape automatically
when the recording is started. If you want to view a
recording at a specific start point, it can easily be done.
This feature allows you to fast forward or rewind the
tape for a desired length of time.
1 Press [SEARCH MODE] so that the Time Search
menu appears.
1 Press [SEARCH MODE] so that the Index Search
menu appears.
2 Enter your desired time to skip
INDEX SEARCH
2 Enter your desired number by
by pressing [PLAY] or [STOP]
TIME SEARCH
2 : 50
03
pressing [PLAY] or [STOP] within 30
seconds.
within 30 seconds.
3 Press [F.FWD] or [REW] to start
time search. If you want to go in
the forward direction, press
[F.FWD]. If you want to go in the
reverse direction, press [REW].
• After time search, the VCR will play the tape
automatically.
3 Press [F.FWD] or [REW] to start
index search. If you want to go in
the forward direction, press [F.FWD].
If you want to go in the reverse
direction, press [REW].
• After index search, the VCR will play the tape
automatically.
RECORDING FUNCTION
It may be unlawful to record playback copyrighted
material without the consent of the copyright owner.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
TIMER RECORDING
You may set the VCR to start recording while you are
away. You can set seven programs to record on specific
days, daily or weekly within a 1 year period.
1 Insert a tape with its safety tab into the VCR.
2 Select main menu by pressing [MENU].
3 Select "TIMER PROGRAMMING" by pressing [PLAY]
or [STOP]. Then, press [F.FWD].
• If you have not yet set the clock, "CLOCK SET"
appears. If so, follow the steps [3] and [4] in "CLOCK
SET UP" section. Then, set the timer recording.
4 Set the timer.
safety tab. To record on it later, cover
the hole with cellophane tape.
Record safety tab
Before recording, make sure:
• The desired channel is selected by pressing [Number] on
(
)
the remote control or the [CHANNEL
]. (If you
connected the VCR to a cable box or satellite box as in
"VCR to TV connections" on page 3, select the VCR to
channel 3 or 4 the same channel as the CH3 or CH4 switch
on the back of the VCR. Then, select the channel you want
to record at the cable box or satellite box. In this case, you
can ONLY record and view the SAME channel.)
Set the program number (1~7)
PROGRAM NUMBER
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
4
Program number which is not set up flashes.
Press [PLAY] or [STOP] repeatedly for the
desired program number.Then, press [F.FWD].
• There is a tape with its safety tab into the VCR.
• The desired recording speed is selected in SP(standard
play) or SLP(super long play) mode by pressing [TAPE
SPEED] on the VCR.
Select once, daily or weekly recording
For once: Press [PLAY] or [STOP] to point to "ONCE".
For daily (Monday~Friday): Press [PLAY] or
PROGRAM NUMBER
ONCE
4
[STOP] to point to "DAILY".
For weekly: Press [PLAY] or [STOP] to point to
DAILY
WEEKLY
Tape Speed
Recording/Playback Time
"WEEKLY".
Then, press [F.FWD]
.
Type of tape
SP mode
SLPmod
T60
1hour
3hour
T120
2hours
6hour
T160
2-2/3hours
8hour
Set the date
First, press [PLAY] or [STOP] for the month. Then, press [F.FWD].
Next, press [PLAY] or [STOP] for the day. Then, press [F.FWD].
• TV STEREO or SAP is selected.
Set the start time
VIEWING AND RECORDING THE
SAME PROGRAM
1 Begin the recording by pressing [RECORD].
• To temporarily stop recording or resume it, press
[PAUSE/STILL]. After the VCR has been in Pause mode
for 5 minutes, it will stop automatically to protect the tape
and the video head from damage.
First, press [PLAY] or [STOP] for the hour. Then, press [F.FWD].
Next, press [PLAY] or [STOP] for the minute. Then, press [F.FWD]
.
And then, press [PLAY] or [STOP] for AM or PM. Then, press [F.FWD]
.
Set the end time
Follow the instructions of "Set the start time" to set the end time.
Set the channel number
Press [PLAY] or [STOP] repeatedly for the desired channel number.
Then, press [F.FWD].
If you connected the VCR to a cable box or satellite box as in "Connect
VCR to TV" on page 3, select the VCR to channel 3 or 4 the same channel
as the CH3 or CH4 switch on the back of the VCR.
Then, select the channel you want to record at the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
2 Press [STOP] when recording is completed.
OTR(One Touch Recording)
This feature allows you to set the recording length simply
by pressing [REC/OTR] on the VCR.
1 Begin OTR by pressing [REC/OTR] on the VCR
repeatedly until the desired recording length appears.
ONE TIME PROGRAM
Set the tape speed
PROGRAM NUMBER
DATE 05/13 MON
START TIME 07:30 PM
END TIME 08:30 PM
4
Press [PLAY] or [STOP] repeatedly for the
desired tape speed.
Then, press [F.FWD].
CHANNEL
16
REC SPEED SP
SP
SLP
REC
OTR(0:30)
OTR(1:00).....
• To go back one step, press [REW].
5 To set another program, repeat step [4]. To exit, press
[EXIT/RESET].
(Normal recording)
6 Press [POWER] to set the timer. The TIMER
indicator on the VCR comes on.
OTR(8:00)
OTR(7:30)
EN
– 5 –
• Go to the digit you want to change by pressing [F.FWD]
or [REW]. Then, enter correct numbers by pressing
[PLAY] or [STOP].
• You may cancel the entire program by pressing [REW]
during the program number flashes.
HINTS FOR TIMER RECORDING
• If there is a power failure or the VCR is unplugged for
more than 30 seconds, the clock setting and all timer
settings will be lost.
• If the tape runs out before the end time, the VCR will
switch to the Stop mode immediately, eject the tape and
the VCR power will be turned off. The TIMER indicator
will flash.
• If a tape is not in the VCR or does not have the safety
tab, the TIMER indicator flashes and timer recording
cannot be performed. Please insert a recordable tape.
5 Press [EXIT/RESET] to exit.
6 Press [POWER] to return to timer stand-by mode.
COUNTER MEMORY FUNCTION
Use this feature to memorize the beginning of recording
start point.
REC
1) Press [COUNTER RESET] on
the remote control to reset the
counter.
TO STOP AN AUTOMATIC TIMER PROGRAM
ALREADY STARTED
Press [STOP/EJECT] on the VCR.
2) Press [COUNTER MEMORY]
on the remote control so that
SP
M0:00:00
“M” appears on the TV screen.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
1 Turn the power on by pressing [POWER].
2 Select main menu by pressing [MENU].
3 Select "TIMER PROGRAMMING" by pressing [PLAY]
or [STOP]. Then, press [F.FWD].
4 Select the program number which you want to
check by pressing [PLAY] or [STOP]. The details of
the selected program appears on the TV screen.
3) Record the program.
4) After recording, press [STOP] then [REW].
• When “0:00:00” is reached, rewinding operation goes
to stop. And you can view the recording program.
• [COUNTER MEMORY] does not function if the Auto
repeat mode is set to [ON]. In this case, set the Auto
repeat mode to [OFF].
• To cancel the Counter memory mode, press
[COUNTER MEMORY] so that “M” disappears from
the TV screen.
SPECIAL FEATURES
COPYING A VIDEO TAPE
MTS (Multi-Channel Television Sound) SYSTEM
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning: Unauthorized recordings of copyrighted video
tapes may be an infringement of copyright laws.
Connect the recording VCR(this unit), the playing VCR
(another source) and your TV using the following diagram.
When you play a VHS tape, or
STOP
12:00AM
CH 32
receive a broadcast on the VCR
tuner channel you are watching,
the status shown below will
appear when you press
STEREO
SAP
1)
2)
[DISPLAY] on the remote control.
When you record the MTS
broadcast signal, you need
setting the MTS mode.
SP
0:00:00
HIFI
[Recording VCR]
(this unit)
[TV set]
(Use for monitoring)
Audio/Video cables
(not supplied)
ANT
AUDIO
L
IN
Coaxial cable
(supplied)
1) Press [MENU] and select "TV STEREO" or "SAP" by
pressing [PLAY] or [STOP]. Then, press [F.FWD] for
fix mode. To exit, press [EXIT/RESET].
• Although a program may be broadcast in both stereo
and second audio, you must select the Recording mode
in TV STEREO or SAP before you record a broadcast.
2) Press [MENU] and select "AUDIO OUT" by pressing
[PLAY] or [STOP]. Then, press [F.FWD]. Next, select
"HIFI" or "MONO" by pressing [PLAY] or [STOP]. To
exit, press [EXIT/RESET].
IN
OUT
OUT
LEFT RIGHT
R
IN
VIDEO
VIDEO
AUDIO
OUT
ANT in
CH3 CH4
IN
OUT
[Playing VCR]
(another source)
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its safety tab into the recording VCR.
3) Press [TAPE SPEED] on the recording VCR to select
the desired recording speed (SP/SLP).
4) Select the “L1” or “L2”position on the recording VCR.
See page 3, under “Using AUDIO/VIDEO Input jacks”.
• While the VCR is set in HIFI stereo mode, HIFI appears on
the TV screen. While the VCR is set in monaural
(MONO) mode, HIFI disappears from the TV screen.
5) Press [REC/OTR] on the recording VCR.
6) Begin playback of the tape in the playing VCR.
• For best results during dubbing, use the VCR’s front
panel controls whenever possible. The remote control
might affect the playing VCR’s operation.
• Always use video-quality shielded cables with RCA-type
connectors. Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in place
of the playing VCR.
MTS RECORDING/MONITOR MODE
Display on the
TV screen
Type of
STEREO/SAP
Selection
Hi-Fi audio track
(2-channel)
Normal audio
track
broadcast
L-channel R-channel
Regular
-None-
-Invalid-
(monaural audio)
Mono
L
Mono
R
Mono
L+R
Stereo
broadcast
STEREO
SAP
-Invalid-
TV STEREO*
SAP*
Main audio Main audio Main audio
program
program
program
Bilingual
broadcast
TO MONITOR THE RECORDING
Sub audio Sub audio
Sub audio
program
1) Turn on the TV and set the TV to channel 3 or 4. Now set
the CH3/CH4 switch on the back of the VCR to match the
channel selected on the TV.
program
L
program
R
TV STEREO*
SAP*
L+R
Sub audio
program
Stereo &
Bilingual
broadcast
STEREO
SAP
Sub audio Sub audio
program program
2) Press [VCR/TV] on the recording VCR so that the VCR
indicator comes on.
* You must select the recording mode in TV STEREO or SAP before you record a broadcast.
EN
– 6 –
AUTO REWIND
REAL TIME TAPE COUNTER
• This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change during blank portions on the tape.)
• The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
When a tape has reached the end during recording,
playback, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
VCR will eject the tape and turn itself to off.
• The VCR will not rewind the tape automatically during
timer recording or One Touch Recording.
• When the Counter Memory is activated, the tape will
rewind to the M0:00:00 and the VCR will go into the
Stop mode.
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate the
PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem.
PROBLEM
No power.
CORRECTIVE ACTION
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
Timer recording is impossible. • Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
(
)
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNEL
] on the VCR.
Cannot view a tape but the
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the VCR is not in the Menu mode.
.
audio is OK
No or poor playback picture.
• Select channel 3 or 4 at your TV, then press [VCR/TV] so that the VCR indicator on the
VCR comes on.
• Fine tune your TV.
TV programs cannot be seen
normally.
No VCR operation from the
infrared Remote Control.
• Re-check the ANT. IN and ANT. OUT connections. See page 3.
• Press [VCR/TV] so that the VCR indicator on the VCR disappears.
• Make sure the power plug is connected to an AC outlet.
• Check batteries in remote control.
Video or color fades in and out • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
when making a copy of a video tape.
SPECIFICATIONS
Operating temperature :
Converter output :
5ºC~40ºC (41ºF~104ºF)
Power requirement :
Power consumption :
Dimensions :
120V, 60Hz
VHF Channel 3 or 4.
14 Watts
W 14-1/4” (360mm)
H 3-5/8” (92mm)
D 8-1/2” (216mm)
4.4 lbs. (2.0 Kg.) (approx.)
• Designs and specifications are subject to change
Weight :
without notice and legal obligation.
• If there is a discrepancy between languages, the
default language will be English.
MAINTENANCE
SERVICING
AUTO HEAD CLEANING
Should your VCR become inoperative, do not try to correct the
problem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power plug, and please call our
help line at
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while the
TV program reception is clear. Dirt accumulated on the video
heads after long periods of use, or the usage of rental or
worn tapes can cause this problem. If a streaky or snowy
picture appears during playback, the video heads in your
VCR may need to be cleaned.
1-800-968-3429,
to locate an Authorized Service Center.
CABINET CLEANING
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
• Wipe the front panel and other exterior surfaces of the VCR
with a soft cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid
near the VCR. Such chemicals may cause damage and
discoloration to the exposed surfaces.
2. If a Video Head Cleaner does not solve the problem, please
call our help line at 1-800-968-3429, to locate an Authorized
Service Center.
NOTES:
• Remember to read the instructions included with the video
head cleaner before use.
• Clean video heads only when problems occur.
EN
– 7 –
CONTROLES DE FUNCIONAMIENTO Y FUNCIONES
Panel frontal
Indicadores
Mando a distancia
1. Compartimiento del videocasete
2. Botón de parada/expulsión
3. Botón de rebobinado
17. Indicador de alimentación
18. Indicador de videocasete introducido
19. Indicador de videograbadora
20. Indicador del grabación
1. Botón de la alimentación (POWER)
2. Botones de número (NUMBER)
3. Botón de menús (MENU)
4. Botón de reproducción
4. Botón de visualizador (DISPLAY)
5. Botón de cámara lenta (SLOW)
5. Botón de pausa/imagen fija
6. Botón de avance rápido
7. Botón de menús
21. Indicador de temporizador
22. Indicador del reloj y tarde
6. Botón de rebobinado (REW)
7. Botón de parada (STOP)
Panel trasero
8. Botón de grabación con un toque
9. Botones de selección de canales
10. Botón de la velocidad de cinta
11. Visualizador digital
12. Sensor de control remoto
13. Botón de videograbadora/televisor
14. Botón de la alimentación
15. Terminal de entrada de audio
16. Terminal de entrada de vídeo
8. Botón de grabación (RECORD)
23. Cable de alimentación
9. Botón de pausa/imagen fija (PAUSE/STILL)
10. Botón de avance rápido (F.FWD)
11. Botón de reproducción (PLAY)
24. Terminal de salida de audio
25. Terminal de entrada de audio
26. Terminal de entrada de antena
27. Terminal de salida de vídeo
28. Terminal de entrada de vídeo
29. Conmutador selector de canales
CH3/CH4
12. Botón de memoria del contador (COUNTER/MEMORY)
13. Botón de salida/reposición (EXIT/RESET)
14. Botón del modo de búsqueda (SEARCH MODE)
15. Botones de selección de canales (CHANNEL)
16. Botón de videograbadora/televisor (VCR/TV)
17. Botón de expulsión (EJECT)
30. Terminal de salida de antena
PREPARACIÓN DE CANALES
PREPARACIÓN DEL RELOJ
(La antena o la caja de televisión por cable
1. Pulse [MENU] hasta que aparezca el menú principal. (Si el
reloj no está puesto en hora y se pulsa [MENU], el menú
AJUSTE DE RELOJ aparece en primer lugar. En este caso,
siga el paso 3.)
2. Pulse [PLAY] o [STOP] para indicar a "AJUSTE DE
RELOJ". Luego, pulse [F.FWD].
deberá estar conectada)
NOTA: Cuando utilice su nueva videograbadora por primera
vez, o en el caso de ser necesario después de producirse un
fallo en la alimentación, la videograbadora se pondrá
inicialmente en el modo de preajuste cuando se pulse
[POWER].
3.
[
[
[
[
[
[
]
]
]
]
]
]
[
[
[
[
[
]
]
]
]
]
[
[
[
[
[
]
]
]
]
]
1. Encienda el televisor y ponga el televisor en el canal 3 ó
4. Ahora ponga el conmutador de la parte trasera de la
videograbadora para que concuerde con el canal
seleccionado en el televisor.
2. Pulse [POWER] para encender la videograbadora.
3. Seleccione "ENGLISH" o "ESPAÑOL"
(Spanish) pulsando [PLAY] o [STOP]. Y
luego pulse [F.FWD].
4. Pulse una vez [F.FWD].
[
]
El sintonizador explora y memoriza todos
los canales activos de su zona. Tras la
exploración, el sintonizador se detiene en
el canal memorizado más bajo.
• Para volver atrás un paso, pulse [REW].
4. Pulse [EXIT/RESET] o [F.FWD] para poner en
funcionamiento el reloj.
LIMITED WARRANTY
Funai Corporation will exchange or repair this product, at its option,
in the event of defect in materials or workmanship as follows:
EXCHANGE DURATION:
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL UNITS), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS,
DEMONSTRATION OR FLOOR MODELS.
1-90 DAYS:
FUNAI CORPORATION will exchange for a new unit
without charge for a period of ninety (90) days from
the date of original retail purchase.
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS
SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR
OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER
WARRANTIES INCLUDING THE WARRANTY OF MERCHANT
ABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, THAT
ARE HEREBY DISCLAIMED BY FUNAI CORPORATION AND ITS
REPRESENTATIVES OR AGENTS IN THE UNITED STATES.
91-365 DAYS: FUNAI CORPORATION will exchange for a factory-
service-to-new-condition unit for a charge of $49.00
for the period of ninety one (91) days to three
hundred sixty five (365) days from the date of
original retail purchase.
REPAIR DURATION:
LABOR:
FUNAI CORPORATION will provide the labor
without charge for a period of ninety (90) days from
the date of original retail purchase.
FUNAI CORPORATION will provide parts to replace
defective parts without charge for a period of one
(1) year from the date of original retail purchase.Two
(2) years for Picture Tube. Certain parts are
excluded from this warranty.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED CENTER. THIS
WARRANTY IS VALID WHEN THE PRODUCT IS DELIVERED
PREPAID TO A FUNAI AUTHORIZED SERVICE FACILITY.
PARTS:
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE, IF AT ANY TIME DURING THE WARRANTY
PERIOD YOU ARE UNABLE TO OBTAIN SATISFACTION WITH
THE EXCHANGE OR REPAIR OF THIS PRODUCT, PLEASE
CONTACT FUNAI CORPORATION.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A
purchase receipt or other proof of original retail purchase will be
required together with the product to obtain exchange or service
under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the
product are altered, replaced, defaced or missing. This SYLVANIA
Limited warranty applies only to product purchased and used in the
United States.
This warranty only covers failures due to defects in material or
workmanship, which occur during normal use. It does not cover
damage which occurs in shipment, or failures which are caused by
repairs, alterations, or parts not supplied by FUNAI CORPORATION,
or damage which results from accident, misuse, abuse, mishandling,
misapplication, alteration, faulty installation, improper maintenance,
commercial use such as hotel, rental or office use of this product, or
damage which results from fire, flood, lightning or other acts of God.
ATTENTION:
FUNAI CORPORATION RESERVES THE RIGHT TO
MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT
PRIOR NOTICE.
For information about your product, or for information on
how to exchange or repair your product, telephone or
write to the following:
FUNAI CORPORATION
Customer Service
100 North Street; Teterboro, NJ 07608
Telephone (800)968-3429
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN02897 / HB445UD #####
|