Sylvania VCR 6260VF User Manual

RF Output Channel  
If channel 3 is already occupied for broadcasting,  
1) Set your TV to channel 4.  
2) Insert a pre-recorded tape into this unit.  
3) Hit [PLAY B] once.  
4) After a few seconds, hold [PLAY B] on the unit for 3 seconds.  
If you need additional operating assistance after  
reading this owners manual or to order replace-  
ment accessories, please call  
Hint  
The RF output channel may  
not change when you adjust  
tracking during playback. In  
this case, stop the playback,  
and start the playback again.  
After that, hold [PLAY B] on  
the VCR for 3 seconds again.  
Owner’s Manual  
TOLL FREE : 1-800-968-3429  
Video Cassette Recorder  
or visit our web site at  
The RF output channel will change to channel 4 from channel 3 and you  
will see a playback picture.  
6260VF  
When a picture does not appear on the TV screen, repeat step 4).  
5) Hit [STOP C] to stop playback.  
1. Before Using Your VCR  
StereoTV Connection  
BasicTV Connection  
VIDEO  
IN  
AUDIO IN  
You can use the AUDIO OUT jacks  
and VIDEO OUT jack on the back of  
the VCR if your TV has Audio/Video  
Input jacks. In this case, you need to  
set the TV to external Line Input  
Mode. Please refer to your TVs  
owners manual.  
L
R
ANT  
AUDIO  
IN  
L
OUT  
IN  
R
Antenna  
Antenna  
Cable TV  
Signal  
or  
Cable TV  
Signal  
or  
OUT  
VIDEO  
(Back of VCR)  
OUT  
IN  
Audio/Video Cables  
(Back of TV)  
(not supplied)  
ANT  
IN  
(Back of TV)  
ANT  
IN  
OUT  
VIDEO  
OUT  
AUDIO OUT  
L
R
2
(Back of VCR)  
Disconnect  
(Back of TV)  
3
OUT  
Connect  
Connect  
RF Cable (supplied)  
Front & RearTerminals  
AUDIO OUT jacks  
AUDIO IN jacks  
Connect the audio cables here through to the audio  
input jacks of a camcorder, another VCR, a stereo  
amplifier, a stereo amplifier or an audio system.  
Connect the audio cables coming from the  
audio output jacks of a camcorder, another  
VCR or an audio source here.  
Plug the AC power cords of the VCR and TV into the AC outlets.  
4
ANT  
AUDIO  
L
ANT IN jack  
Connect your antenna or cable box here.  
IN  
ANT  
AUDIO  
IN  
Hint for Cable Box or Satellite Box  
L
OUT  
IN  
OUT  
IN  
R
R
VIDEO  
OUT  
ANT OUT jack  
VIDEO  
OUT  
IN  
OUT  
To select channels of the cable box or  
satellite box  
1) Turn on the unit by hitting [POWER], then  
hit [VCR/TV].The POWERand the  
VCR/TVindicator on the front panel will  
(Back of VCR)  
(Cable box or  
Connect the supplied RF cable to the  
ANT  
Antenna or  
OUT  
IN  
IN  
antenna input jack on your TV.  
Satellite box)  
Cable TV  
IN  
OUT  
VIDEO OUT jack  
E
OUT  
signal  
RF cable  
(supplied)  
Connect the video cable here through the video  
input jack of a camcorder, another VCR or a TV.  
VIDEO IN jack  
(Back of TV)  
Connect the video cable coming from the  
video output jack of a camcorder, another  
VCR or an audio-visual source (laser disc  
player, video disc player, etc.) here.  
appear, then press [CHANNEL  
] to  
Select this connection when you want to view  
or record a scrambled channel. With this con-  
nection, channels cannot be changed on the  
unit. You can view or record ONLY the chan-  
nels you have selected on the cable box or  
the satellite box.  
POWER  
CHANNEL  
MEN  
select channel 3 or 4 (the same channel as  
the output channel of the cable box or  
satellite box).  
VIDEO  
L
-
AUDIO  
-
R
TAPE IN  
If you use the channel 4, you need to  
change the units RF output to channel 4.  
Refer to RF Output Channel.  
2) At the TV, select channel 3 or 4 (the same  
channel as you have selected at step 1).  
3) On the cable box or satellite box, select the  
channel you want to view or record.  
Installing the Batteries for  
the Remote Control  
Install two AA batteries  
(supplied) matching the  
polarity indicated on  
the bottom of the  
Supplied Accessory  
Remote control  
(NA376UD) with  
two AA batteries  
RF cable  
Owners manual  
(WPZ0901TM002) (1VMN20688)  
• While you are recording, only the recorded  
channel can be viewed.  
remote control.  
Printed in China  
- 1 -  
1VMN20688 / HJ411UD #####  
 
3. Preparation for Use  
Turn on the Unit for the FirstTime  
To Add/Delete Channels  
Clock Set Up  
MENU  
MENU  
To Select a Channel  
You can select a channel by using  
the Number buttons on the remote  
control.  
Notes for using the Number but-  
tons:  
- M E N U -  
- M E N U -  
1
1
1
5
6
7
CLOCK SET  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
B CHANNEL SET UP  
CLOCK SET  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
B CLOCK SET  
MONTH DAY  
YEAR  
Turn on the TV and set  
it to channel 3.  
1 0 0 3 MON 2 0 0 5  
/
HOUR MINUTE AM/PM  
0 5 – – – –  
LANGUAGE SELECT  
AUDIO OUT  
LANGUAGE SELECT  
AUDIO OUT  
or  
or  
or  
If channel 3 is already occupied for broad-  
:
TV STEREO  
SAP  
[ON]  
TV STEREO  
SAP  
[ON]  
casting, see RF Output Channelsection.  
or  
When selecting cable channels which  
are higher than 99, enter channel  
numbers as a three-digit number (for  
example: 117, hit [1], [1], [7]).  
Select the current hour.  
or  
If the clock is not set, the  
CLOCK SET screen  
appears when you press  
[MENU]. In this case, go  
to step 2).  
Remote Control TV Screen  
2
POWER  
LANGUAGE SELECT  
You must precede single-digit  
channel numbers with a zero (for  
example: 02, 03, 04 and so on).  
CLOCK SET  
B ENGLISH  
FRANCAIS  
ESPAÑOL  
[ON]  
MONTH DAY  
YEAR  
1 0 0 3 MON 2 0 0 5  
/
2
3
CHANNEL SET UP  
2
3
4
CLOCK SET  
HOUR MINUTE AM/PM  
0 5 4 0 – –  
To Preset the Channel Again  
1) Hit [MENU] until the main menu appears.  
:
or  
AUTO SET UP  
MONTH DAY  
1 0 – –  
YEAR  
– – – –  
B MANUAL SET UP  
/
or  
2) Select "CHANNEL SET UP" by pressing  
[PLAY B] or [STOP C]. Then, hit  
[F.FWD g].  
HOUR MINUTE AM/PM  
– – – – – –  
or  
Select the current minute.  
CLOCK SET  
:
Select the current month.  
3) Select "AUTO SET UP" by pressing  
[PLAY B] or [STOP C]. Then, hit  
[F.FWD g]. After scanning, the tuner stops  
on the lowest memorized channel.  
3
CH 01  
MONTH DAY  
YEAR  
AUTO SET UP  
1 0 0 3 MON 2 0 0 5  
/
MANUAL SET UP  
CLOCK SET  
To Change the On-Screen Language  
1) Hit [MENU] until the main menu appears.  
HOUR MINUTE AM/PM  
CHANNEL 30  
ADD  
(CATV)  
0 5  
:
4 0  
P M AM  
B PM  
MONTH DAY  
1 0 0 3  
YEAR  
– – – –  
/
or  
2) Select "LANGUAGE SELECT" by pressing  
[PLAY B] or [STOP C]. Then, hit  
[F.FWD g].  
Do you connect the cable from the cable box  
or the satellite box to the VCRs ANT-IN jack?  
HOUR MINUTE AM/PM  
– – – – – –  
or  
Select AMor PM.  
:
Yes  
Select the channel to be  
added or deleted.  
3) Select "ENGLISH", "FRANCAIS" or  
"ESPAÑOL" by pressing [PLAY B] or  
[STOP C]. Then, hit [C.RESET/EXIT].  
Select the current day.  
Yes Hit [MENU] to  
exit  
Refer to Hint for Cable Box or  
8
To exit the CLOCK SET  
screen  
Satellite Boxsection on page 1.  
No  
4
5
MANUAL SET UP  
No Please wait for a few minutes.  
CLOCK SET  
CHANNEL 30  
DELETE  
(CATV)  
After scanning...  
MONTH DAY  
1 0 0 3  
YEAR  
2 0 0 5  
or  
/
The tuner stops on the lowest memorized  
channel.  
or  
HOUR MINUTE AM/PM  
– – – – – –  
:
You can select only the channels memorized  
in the unit by using [CHANNEL  
If "AUTO SET UP" appears on the TV screen  
again, check the cable connections. Then, hit  
[F.FWD g] once again.  
Hint  
].  
Select ADDor DELETE.  
To go back one step, hit [REW h] (during  
Hint  
Select the current year.  
steps 2 to 7).  
If you accidentally select Spanish or French  
and need English: Hit [MENU] and choose  
SELEC. IDIOMA, or SELECTION LANGUE.  
Hit [F.FWD g] and select ENGLISH.  
Finally, hit [C.RESET/EXIT].  
Your clock setting will be lost if either there  
is a power failure or if this unit has been  
unplugged for more than 30 seconds.  
Hint  
C.RESET  
EXIT  
To exit the  
menu.  
Repeat these steps only if either there  
was a power failure or if this unit has been  
unplugged for more than 30 seconds.  
- 3 -  
EN  
 
4. Precautions  
Precautions  
Troubleshooting Guide  
Install Location  
For safety and optimum performance of  
this unit:  
If this unit does not perform properly when operated as instructed in this Owners  
Manual, check this unit consulting the following checklist.  
Important Copyright Information  
Unauthorized recording or use of broad-  
cast television programming, video tape,  
film or other copyrighted material may  
violate applicable copyright laws. We  
assume no responsibility for the unau-  
thorized duplication, use, or other acts  
which infringe upon the rights of copy-  
right owners.  
PROBLEM  
CORRECTIVE ACTION  
Install the unit in a horizontal and sta-  
ble position. Do not place anything  
directly on top of the unit. Do not place  
the unit directly on top of the TV.  
Shield it from direct sunlight and keep it  
away from sources of intense heat.  
Avoid dusty or humid places. Avoid  
places with insufficient ventilation for  
proper heat dissipation. Do not block  
the ventilation holes on the sides of the  
unit. Avoid locations subject to strong  
vibration or strong magnetic fields.  
No power.  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Timer recording is impossible.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the VCR clock is set correctly.  
Cannot go into Recording mode. Make sure the tape has a record tab. If needed, cover the hole with  
adhesive tape.  
A Note about Recycling  
Playback picture is partially noisy. Adjust tracking control for a better picture by pressing  
[CHANNEL  
].  
This product's packaging materials are  
recyclable and can be reused. Please  
dispose of any materials in accordance  
with your local recycling regulations.  
Batteries should never be thrown away  
or incinerated but disposed of in accor-  
dance with your local regulations con-  
cerning chemical wastes.  
Cannot view a tape but the audio  
is OK.  
Head cleaning may be necessary. Refer to Auto Head Cleaningon  
page 8.  
Make sure the VCR is not in the Menu mode.  
No or poor playback picture.  
Change the RF output channel to CH4. Then select the same  
channel on the TV.  
Avoid the Hazards of Electrical Shock and  
Fire  
Do not handle the power cord with wet  
hands.  
Do not pull on the power cord when  
disconnecting it from AC wall outlet.  
Grasp it by the plug.  
Fine tune your TV.  
TV programs cannot be seen nor- Re-check the ANT-IN and ANT-OUT connections. See page 1.  
mally.  
Hit [VCR/TV] on the remote control so that the VCR/TV indicator on  
the unit disappears.  
No operation from the infrared  
Remote Control.  
Make sure the power plug is connected to an AC outlet.  
Check batteries in remote control.  
Note to the Cable TV System Installer  
This reminder is provided to call the  
Cable TV system installers attention to  
Article 820-40 of the NEC that provides  
guidelines for proper grounding and in  
particular, specifies that the cable  
ground should be connected to the  
grounding system of the building, as  
close to the point of cable entry as pos-  
sible.  
Video or color fades in and out when You cannot copy a copyrighted video tape. You are experiencing copy  
making a copy of a video tape.  
guard protection.  
Moisture Condensation Warning  
Specifications  
Moisture condensation may occur inside  
the unit when it is moved from a cold  
place to a warm place, or after heating a  
cold room or under conditions of high  
humidity. Do not use the unit at least for  
2 hours until its inside is dry.  
Video Heads :  
Operating temperature : 41°F~104°F  
Four Heads  
Power requirement : 120V, 60Hz  
Power consumption : 14 Watts  
(5°C~40°C)  
VHF Channel 3 or 4  
Dimensions :  
W 14-3/16" (360mm)  
Converter output :  
H 3-5/8" (92mm)  
D 8-9/16" (216mm)  
4.0 lbs. (1.8 Kg.)  
(approx.)  
Weight :  
CAUTION:  
FCC Warning  
TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO  
WIDE SLOT, FULLY INSERT.  
ATTENTION:  
Designs and specifications are subject to change without notice and legal obligation.  
If there is a discrepancy between languages, the default language will be English.  
This equipment may generate or use  
radio frequency energy. Changes or  
modifications to this equipment may  
cause harmful interference unless the  
modifications are expressly approved in  
the instruction manual. The user could  
lose the authority to operate this equip-  
ment if an unauthorized change or modi-  
fication is made.  
POUR ÉVITER LES CHOCS  
ÉLECTRIQUES, INTRODUIRE LA  
LAME LA PLUS LARGE DE LA  
FICHE DANS LA BORNE CORRE-  
SPONDANTE DE LA PRISE ET  
POUSSER JUSQUAU FOND.  
Make your contribution to the environment!!!  
Used up batteries do not belong in the dust bin.  
You can dispose of them at a collection point for used up batteries or  
special waste.Contact your council for details.  
- 4 -  
EN  
 
5. Playback  
Turn on the TV and set it to  
channel 3.  
7. Other Operations  
To cue or review picture during play- To play back in slow motion  
Before:  
1
back (Picture Search)  
Hit [SLOW] during playback or the still mode.  
If the noise bar appears on the TV  
screen, you can reduce it by pressing  
POWER  
Hit [F.FWD g] or [REW h].  
Hit it again and the VCR will now  
search in super high speed. (in the  
LP/SLP modes only.)  
EJECT  
1
VCR/TV  
3
4
3
If channel 3 is already occupied for broad-  
casting, see RF Output Channelsection.  
2
5
8
0
[CHANNEL  
].  
CHANNEL  
4
6
To temporarily stop recording  
SEARCH  
-MODE  
Remote Control TV Screen  
2
4
7
9
1
3
(Pause mode)  
CHANNEL  
MENU REC/OTR STOP/EJECT  
REW  
PLAY  
F.FWD  
To freeze the picture on TV screen  
TAPE IN  
C.RESET  
EXIT  
MENU  
SLOW  
during playback (Still mode)  
Hit [PAUSE/STILL].  
PLAYB  
PAUSE  
/STILL  
REC/OTR SPEED  
DISPLAY  
Hit [PAUSE/STILL]. Each time you hit  
the button, the picture will be forwarded  
by one frame.  
During the rec pause mode, five  
C
TAPE IN  
marks appear on the TV screen. Each  
mark represents one minute.  
C
3 2  
4
If the picture begins to vibrate vertically Hit it again to resume recording.  
2
during the still mode, stabilize the pic-  
Auto Rewind  
Hint  
ture by pressing [CHANNEL  
].  
EJECT  
When a tape reaches its end during play-  
back, fast-forward, or recording (except  
timer recording and One Touch  
Recording), the tape will automatically  
rewind to the beginning. After rewinding  
finishes, the unit will eject the tape and  
turn itself to off.  
STOP  
EJECT A  
If the picture is distorted or rolling verti-  
cally, adjust the vertical hold control on  
your TV if equipped.  
When a tape without record tab is inserted, the unit will start playback auto-  
matically at step 1).  
Tracking will be automatically adjusted upon playback. To adjust the tracking manu-  
ally, press [CHANNEL ].  
Counter Reset  
Hit [C.RESET/EXIT].  
6. Recording & OTR (One Touch Recording)  
Hint  
Before:  
Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the  
2
Turn on the TV and set it to  
video head.  
To return to playback from the Picture Search/Still/Slow mode, hit [PLAY B].  
channel 3.  
If channel 3 is already occupied for  
1
4
2
6
broadcasting, see RF Output Channelsection.  
POWER  
EJECT  
1
VCR/TV  
3
8. On-Screen Operations  
Remote Control TV Screen  
1
2
2
5
8
0
with tab  
CHANNEL  
4
6
1
4
7
2
5
8
0
3
6
9
1
2
3
4
To call up the main menu  
CHANNEL  
SEARCH  
-MODE  
CH12  
7
9
- M E N U -  
MENU  
CHANNEL  
MENU REC/OTR STOP/EJECT  
REW  
PLAY  
F.FWD  
C.RESET  
EXIT  
TAPE IN  
MENU  
SLOW  
TAPE IN  
B TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
Select the chan-  
nel to record.  
PAUSE  
/STILL  
REC/OTR SPEED  
DISPLAY  
4
3
5
CHANNEL  
MENU REC/OTR STOP/EJECT  
REW  
PLAY  
F.FWD  
LANGUAGE SELECT  
TAPE IN  
5
6
Select the desired tape  
speed.  
3
SP  
SPEED  
To select an item  
Tape Speed  
Recording/Playback Time  
Type of tape  
SP mode  
SLP mode  
T60  
T120  
2hours  
6hour  
T160  
2-2/3hours  
8hour  
- M E N U -  
1
4
2 3  
1hour  
3hour  
or  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
B CHANNEL SET UP  
CLOCK SET  
Accidental erasure prevention  
REC/OTR  
4
LANGUAGE SELECT  
To prevent accidental recording on a record-  
ed cassette, remove its record tab. To record  
on it later, cover the hole with adhesive tape.  
REC  
POWER  
To decide  
EJECT  
1
VCR/TV  
Hit [REC/OTR] repeatedly to select the desired  
recording length.  
2
5
8
0
3
6
Record tab  
CHANNEL SET UP  
CHANNEL  
4
REC  
OTR(0:30)  
OTR(1:00).....  
(Normal recording)  
AUTO SET UP  
SEARCH  
-MODE  
7
9
B MANUAL SET UP  
OTR(8:00)  
OTR(7:30)  
C.RESET  
EXIT  
MENU  
SLOW  
4
3
4 1  
2
EJECT  
PAUSE  
/STILL  
5
6
Hint  
REC/OTR SPEED  
DISPLAY  
STOP  
EJECT A  
To exit the menu  
C.RESET  
EXIT  
MENU  
If you have connected this unit to a cable box or satellite box, refer to Hint for Cable  
Box or Satellite Boxsection on page 1.  
or  
- 5 -  
EN  
 
9. Recording Features  
Timer Recording  
Hints forTimer Recording  
Insert a tape with its record tab into the unit.  
If there is a power failure or the unit has been unplugged for more than 30 sec-  
onds, the clock setting and all timer settings will be lost.  
If the tape runs out before the end time, the unit will switch to the Stop mode  
immediately, eject the tape and the power will be turned off. The TIMER indicator  
will flash.  
If a tape is not in the unit or does not have the record tab, the TIMER indicator  
flashes and timer recording cannot be performed. Please insert a recordable tape.  
When all the Timer Recording are completed, the TIMER indicator flashes.  
To play or eject the recorded tape, hit [POWER] first, and then press  
- M E N U -  
1
ONE TIME PROGRAM  
PROGRAM NUMBER  
5
Select the desired start  
time (hour).  
9
B TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
1
DATE  
1 0 / 2 4 MON  
MENU  
START TIME 0 7 : 3 0 PM  
END TIME 0 8 : 3 0 PM  
ONE TIME PROGRAM  
or  
PROGRAM NUMBER  
DATE 10 / 2 4 MON  
START TIME 0 7 : 3 0 – –  
END TIME – – : – – – –  
1
CHANNEL  
1 6  
or  
REC SPEED SP  
TIMER PROGRAMMING  
B SP  
SLP  
PROG  
12345678  
CHANNEL  
– –  
DATE  
Select the desired recording speed.  
REC SPEED – –  
[PLAY  
To cancel a Timer Recording that is in progress  
Hit [STOP/EJECT ] on the unit.  
B
] or [EJECT  
A
].  
START TIME  
C.RESET  
EXIT  
Select the  
minute  
Availableprogram  
number flashes.  
C
/
A
or  
POWER  
10 Turn off the  
VCR for  
Copying aVideoTape  
2
recording  
TIMER indicator on the VCR lights up.  
PROGRAM NUMBER  
1
Warning: Unauthorized recordings of copyrighted video tapes  
DATE  
– – / – –  
(Back of TV)  
may be an infringement of copyright laws.  
START TIME – – : – – – –  
END TIME – – : – – – –  
(Back of Playing VCR)  
(Back of Recording VCR*)  
CHANNEL  
REC SPEED – –  
– –  
or  
Hint  
ONE TIME PROGRAM  
PROGRAM NUMBER  
6
Select an empty program  
number.  
To go back one step, hit [REW h] (during  
2
1
AUDIO  
AUDIO  
L
ANT  
ANT  
IN  
L
1
DATE  
1 0 / 2 4 MON  
steps 3) to 9) ).  
OUT  
IN  
Connect  
OUT  
IN  
START TIME 0 7 : 3 0 PM  
R
R
Connect  
OUT  
END TIME – – : – – – –  
VIDEO  
VIDEO  
or  
To Check, Correct, or Cancel a  
Timer Program  
1) Turn the power on by hitting  
CHANNEL  
– –  
OUT  
IN  
OUT  
IN  
REC SPEED – –  
AM  
RF Cable  
(supplied)  
B PM  
Audio/Video Cables  
(not supplied)  
*Front input jacks are also available  
Select AMor PM.  
3
4
PROGRAM NUMBER  
1
[POWER].  
2) Select main menu by hitting  
[MENU].  
1) Insert a pre-recorded tape into the playing VCR.  
2) Insert a tape with its record tab into the recording VCR.  
B ONCE  
DAILY  
WEEKLY  
3) Select "TIMER PROGRAM-  
MING" by pressing [PLAY B] or  
[STOP C]. Then, hit  
or  
3) Hit [SPEED] on the remote control of the recording VCR to select the  
7
8
Repeat the procedure in steps  
5 and 6 to set the end time.  
Select ONCE, DAILY”  
(Mon-Fri), or WEEKLY.  
desired recording speed (SP/SLP).  
[F.FWD g].  
4) Select the L1or L2position on the recording VCR.  
4) Select the program number  
which you want to check by  
pressing [PLAY B] or  
[STOP C]. The details of the  
program you selected will  
appear on the TV screen.  
Go to the digit you want to  
change by pressing  
To use the input jacks on the back of this unit, select "L1" position by  
hitting [0], [0], [1] on the remote control or [CHANNEL  
].  
To use the input jacks on the front of this unit, select "L2" position by  
ONE TIME PROGRAM  
Select the desired month.  
hitting [0], [0], [2] on the remote control or [CHANNEL  
5) Hit [REC/OTR] on the recording VCR.  
].  
PROGRAM NUMBER  
DATE 1 0 / 2 4 MON  
START TIME 0 7 : 3 0 PM  
END TIME 0 8 : 3 0 PM  
1
ONE TIME PROGRAM  
PROGRAM NUMBER  
DATE 1 0 / 0 3 MON  
1
or  
6) Begin playback of the tape in the playing VCR.  
or  
CHANNEL  
1 6  
START TIME – – : – – – –  
C / A] on the recording VCR,  
REC SPEED – –  
7) To stop recording, hit [STOP/EJECT  
END TIME – – : – – – –  
[F.FWD  
g] or [REW h].  
Then, enter correct numbers by  
pressing [PLAY B] or  
CHANNEL  
– –  
then stop playback of the tape in the playing VCR.  
REC SPEED – –  
Select the desired channel.  
Hint  
[STOP C].  
If you have connected the unit to a cable  
box or satellite box as the Connection on  
page 1, select the VCR to channel 3 or 4  
(the RF output channel of the VCR).  
Then, select the desired channel at the  
cable box or satellite box. Leave the cable  
box or satellite box on for timer recording.  
Select the desired day.  
You may cancel the entire pro-  
gram by hitting [REW h] while  
the program number flashes.  
5) Hit [C.RESET/EXIT] to exit.  
6) Hit [POWER] to return to timer  
stand-by mode.  
For best results during dubbing, use the VCRs front panel controls whenever possible. The  
remote control might affect the playing VCRs operation.  
Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are  
not recommended.  
or  
You can program one  
year in advance.  
You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs.  
• “L1or L2is found before the lowest memorized channel. (Example: CH02)  
"L2" input jacks are on the front of this unit.  
- 6 -  
EN  
 
11. MTS System  
10. Special Features  
(Multi-Channel Television Sound)  
Time Search  
Index Search  
Auto Repeat  
WhenYou Receive or Record a  
Program Broadcast in MTS  
WhenYou Play Back aTape  
Recorded in Hi-Fi Stereo  
You can search backward and  
forward a spcific length of time  
on a tape.  
This function will playback a  
tape repeatedly from the begin-  
ning when the tape reaches to  
the end.  
You can skip the program backward  
and forward by the Index Mark.  
Insert a tape into this unit.  
When you receive a broad-  
cast on the VCR, you can  
check the type of the broad-  
cast by hitting.  
When "TV STEREO" or  
"SAP" selection is valid,  
select them by following  
steps. This selection is need-  
ed when you record the pro-  
gram.  
If you have connected a  
stereo TV to this VCR, select  
"STEREO".  
If you have connected a  
monaural TV to this VCR,  
select "MONO".  
Insert a tape into this unit.  
1
INDEX SEARCH  
SEARCH  
Insert a tape into this unit.  
1
– –  
-MODE  
TIME SEARCH  
SEARCH  
-MODE  
: – –  
MENU  
- M E N U -  
1
TIMER PROGRAMMING  
B AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
Hit once.  
LANGUAGE SELECT  
AUDIO OUT  
Your Selection  
STEREO  
Hit twice.  
MONO  
Monaural  
L+R  
L-channel  
R-channel  
Type of recorded tape  
TV STEREO  
SAP  
[ON]  
non Hi-Fi tapes  
Monaural  
Monaural  
Hi-Fi tapes  
recorded in  
Hi-Fi stereo  
or  
L
R
2
INDEX SEARCH  
0 3  
SAP means Second Audio  
Program (usually second lan-  
guage).  
Hi-Fi tapes  
recorded main  
audio program  
2
Select the desired length  
of time for fast forwarding  
or rewinding.  
Main audio  
program  
Main audio  
program  
Main audio  
program  
Hi-Fi tapes  
recorded second  
audio program  
or  
Second audio Second audio Second audio  
program  
program  
program  
Display on the  
TV screen  
Type of  
broadcast  
STEREO/SAP  
Selection  
TIME SEARCH  
2 : 5 0  
Regular  
MENU  
-MENU-  
-None-  
-Invalid-  
-Invalid-  
1
(monaural audio)  
- M E N U -  
2
3
01 ~ 20  
CURRENT PROGRAM  
Beginning  
Stereo  
broadcast  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
End  
STEREO  
TIMER PROGRAMMING  
B AUTO REPEAT [ON]  
CHANNEL SET UP  
CLOCK SET  
LANGUAGE SELECT  
AUDIO OUT  
TV STEREO  
SAP  
of tape  
of tape  
or  
TV STEREO  
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5  
02 01 01 02 03  
(main audio program)  
Bilingual  
broadcast  
SAP  
LANGUAGE SELECT  
SAP  
B AUDIO OUT  
TV STEREO  
SAP  
(second audio program)  
[ON]  
INDEX MARK  
[ON]  
TV STEREO  
0:01~ 9:59  
(1 minute~9 hours  
and 59 minutes)  
Stereo &  
Bilingual  
broadcast  
(stereo main audio program)  
STEREO  
SAP  
or  
SAP  
(second audio program)  
MENU  
-MENU-  
1
To rewind  
To fast forward  
3
4
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
LANGUAGE SELECT  
AUDIO OUT  
B TV STEREO  
SAP  
AUTO REPEAT B  
To rewind  
To fast forward  
After searching,  
3
4
[ON]  
2
Hint  
AUDIO OUT  
After searching,  
or  
To cancel Auto Repeat, follow steps 1)-2)  
above. Then, hit [F.FWD g] so that [OFF]  
appears beside AUTO REPEAT. Hit  
[C.RESET/EXIT] to exit.  
B HIFI  
MONO  
[ON]  
Select TV STEREOor  
SAP”  
or  
PLAYB  
If menu remains on the TV screen at step  
3), hit [C.RESET/EXIT] to exit.  
PLAYB  
Hint  
Select HIFIor MONO”  
The unit records an index mark at the  
beginning of the recording when you make  
a recording. There should be time gap  
between index marks for the Index Search.  
2
To exit the menu.  
C.RESET  
EXIT  
3
To exit the menu.  
C.RESET  
EXIT  
Hints for Index Search & Time Search  
These functions are not available during recording.  
Hit [STOP C] to stop the search.  
If the end of the tape is reached during a Search, the VCR will cancel the search  
and rewind the tape.  
- 7 -  
EN  
 
12. Information  
Maintenance  
Limited Warranty  
Funai Corporation will exchange or repair this product, at THIS WARRANTY DOES NOT COVER PACKING  
its option, in the event of defect in materials or workman- MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
Servicing  
Auto Head Cleaning  
If this unit become inoperative, do not try to  
correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug  
the power plug, and please call our help line  
mentioned on the front page to locate an  
Authorized Service Center.  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long peri-  
ods of use, or the usage of rental or worn tapes  
can cause this problem. If a streaky or snowy pic-  
ture appears during playback, the video heads in  
your VCR may need to be cleaned.  
ship as follows:  
CONTROL UNITS), ANY COSMETIC PARTS, COM-  
PLETE ASSEMBLY PARTS, DEMONSTRATION OR  
FLOOR MODELS.  
EXCHANGE DURATION:  
1-90 DAYS:  
FUNAI CORPORATION will exchange  
FUNAI CORPORATION AND ITS REPRESENTATIVES  
OR AGENTS SHALL IN NO EVENT BE LIABLE FOR  
ANY GENERAL, INDIRECT OR CONSEQUENTIAL  
DAMAGES ARISING OUT OF OR OCCASIONED BY  
THE USE OF OR THE INABILITY TO USE THIS PROD-  
UCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES INCLUDING THE WARRANTY  
OF MERCHANT ABILITY, AND FITNESS FOR A PAR-  
TICULAR PURPOSE, THAT ARE HEREBY DIS-  
CLAIMED BY FUNAI CORPORATION AND ITS REP-  
RESENTATIVES OR AGENTS IN THE UNITED  
STATES.  
for a new unit without charge for a peri-  
od of ninety (90) days from the date of  
original retail purchase.  
91-365 DAYS: FUNAI CORPORATION will exchange  
for a factory-service-to-new-condition  
Cabinet Cleaning  
unit for a charge of a retailed price unit  
for the period of ninety one (91) days to  
three hundred sixty five (365) days from  
the date of original retail purchase.  
Wipe the front panel and other exterior sur-  
faces of the VCR with a soft cloth immersed  
in lukewarm water and wrung dry.  
Never use a solvent or alcohol. Do not spray  
insecticide liquid near the VCR. Such chemi-  
cals may cause damage and discoloration to  
the exposed surfaces.  
1. Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2. If a Video Head Cleaner does not solve the  
problem, please call our help line mentioned on  
page 1 to locate an Authorized Service Center.  
NOTES:  
REPAIR DURATION:  
LABOR:  
FUNAI CORPORATION will provide the  
labor without charge for a period of  
ninety (90) days from the date of origi-  
nal retail purchase.  
FUNAI CORPORATION will provide  
parts to replace defective parts without  
charge for a period of one (1) year from  
the date of original retail purchase.  
Certain parts are excluded from this  
warranty.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST  
BE PERFORMED BY A FUNAI AUTHORIZED CEN-  
TER. THIS WARRANTY IS VALID WHEN THE PROD-  
UCT IS DELIVERED PREPAID TO A FUNAI AUTHO-  
RIZED SERVICE FACILITY.  
Remember to read the instructions included  
with the video head cleaner before use.  
PARTS:  
Clean video heads only when problems occur.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF AT ANY TIME  
DURING THE WARRANTY PERIOD YOU ARE UNABLE  
TO OBTAIN SATISFACTION WITH THE EXCHANGE  
OR REPAIR OF THIS PRODUCT, PLEASE CONTACT  
FUNAI CORPORATION.  
Instrucciones en Español  
PREPARACIÓN DE CANALES  
(La antena o la caja de televisión por  
cable deberá estar conectada)  
NOTES: Cuando utilice su nueva  
videograbadora por primera vez, o en el  
caso de ser necesario después de  
producirse un fallo en la alimentación, la  
videograbadora se pondrá inicialmente en el  
modo de preajuste cuando se pulse  
[POWER].  
1. Encienda el televisor y ponga el televisor  
en el canal 3.  
2. Pulse [POWER] para encender la  
videograbadora.  
3. Seleccione "ENGLISH",  
"FRANCAIS"(French) o  
"ESPAÑOL" (Spanish)  
pulsando [PLAY B] o  
[STOP C].Y luego  
pulse [F.FWD g].  
4. Pulse una vez  
[F.FWD].  
PREPARACIÓN DEL RELOJ  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGI-  
NAL RETAIL PURCHASER. A PURCHASE RECEIPT  
OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE  
WILL BE REQUIRED TOGETHER WITH THE PROD-  
UCT TO OBTAIN EXCHANGE OR SERVICE UNDER  
THIS WARRANTY.  
1. Pulse [MENU] hasta que aparezca el  
menú principal. (Si el reloj no está puesto  
en hora y se pulsa [MENU], el menú  
AJUSTE DE RELOJ aparece en primer  
lugar. En este caso, siga el paso 3.)  
ATTENTION:  
FUNAI CORPORATION RESERVES THE  
RIGHT TO MODIFY ANY DESIGN OF THIS  
PRODUCT WITHOUT PRIOR NOTICE.  
For information about your product, or for  
information on how to exchange or repair your  
product, telephone or write to the following:  
This warranty shall not be extended to any other person  
or transferee.  
2. Pulse [PLAY B]  
o
[STOP C] para indicar a  
"AJUSTE DE RELOJ". Luego, pulse [F.FWD g]  
.
This warranty is void and of no effect if any serial num-  
bers on the product are altered, replaced, defaced or  
missing. This SYLVANIA Limited warranty applies only to  
product purchased and used in the United States.  
This product is produced for home use and this warranty  
only covers failures due to defects in material or work-  
manship, which occur during normal use. It does not  
cover damage which occurs in shipment, or failures  
which are caused by repairs, alterations, or parts not  
supplied by FUNAI CORPORATION, or damage which  
results from accident, misuse, abuse, mishandling, mis-  
application, alteration, faulty installation, improper main-  
tenance, commercial use such as hotel, rental or office  
use of this product, or damage which results from fire,  
flood, lightning or other acts of God.  
3.  
Pulse repetidamente [PLAY B] o [PLAY B].  
Ajuste el mes.  
Luego, pulse [F.FWD g].  
Ajuste el día.  
Pulse repetidamente [PLAY B] o [STOP C].  
Luego, pulse [F.FWD g].  
FUNAI CORPORATION, INC.  
SERVICE CENTER  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel :1-800-968-3429  
Pulse repetidamente [PLAY B] o [STOP C].  
Ajuste el año.  
Luego, pulse [F.FWD g].  
Pulse repetidamente [PLAY B] o [STOP C].  
Ajuste la hora.  
Luego, pulse [F.FWD g].  
Ajuste el minuto. Pulse repetidamente [PLAY B] o [PLAY B].  
SELEC. IDIOMA  
Luego, pulse [F.FWD g].  
ENGLISH  
Ajuste la  
mañana (AM) o  
Head Office: 100 North Street, Teterboro, NJ 07608  
PLEASE DO NOT SHIP YOUR UNIT TO THE  
TETERBORO ADDRESS.  
Pulse repetidamente [PLAY B] o [PLAY B].  
FRANCAIS  
la tarde (PM).  
B ESPAÑOL  
[ON]  
AJUSTE DE RELOJ  
Para volver atrás un  
paso, pulse [REW h].  
4. Pulse [F.FWD g]  
para poner en fun-  
MES  
10  
DIA  
03 LUN  
AÑO  
2005  
/
El sintonizador explora y memoriza todos  
los canales activos de su zona. Tras la  
exploración, el sintonizador se detiene en  
el canal memorizado más bajo.  
HORA MINUTO AM/PM  
05  
:
40  
PM AM  
B PM  
cionamiento el reloj.  
- 8 -  
EN  
 

Sharp Cash Register ER A450T User Manual
Sharp Mouse 100 EVIK User Manual
Shure Headphones SRH750DJ User Manual
Sierra Wireless Modem 2130374 v3 User Manual
Sony Cassette Player CC 222 User Manual
Sony Ericsson Headphones HCB 400 User Manual
Sony MP3 Docking Station RDHGTK33iP User Manual
Sony Stereo System TC WE675 User Manual
Sony Video Game Console SCPH 7001 User Manual
Stiga Lawn Mower 11 3203 26 User Manual