SCD 249
12
PORTABLE COMPACT DISC PLAYER
WITH SUPER BASS BOOST SYSTEM
9
8
11
10
LECTEUR DE DISQUE COMPACT PORTABLE
AVEC SYSTÈME D’AMPLIFICATION DYNAMIQUE DES GRAVES
7
1
2
3
4
5
6
ENGLISH
LOCATION OF CONTROLS
1. PROG (PROGRAM)
2. SKIP / SEARCH DOWN
3. SKIP / SEARCH UP
4. PLAY / PAUSE (POWER ON)
5. STOP / OFF (POWER OFF)
6. MODE
7. VOLUME
8. B.B.S. BUTTON (BASS BOOST BUTTON)
9. HEADPHONE JACK
10. OPEN BUTTON
11. DC JACK
12. BATTERY COPMARTMENT
CAUTION
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THIS SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE
PERSONNEL.
INSTRUCTION MANUAL
MODE D’EMPLOI
— 2
—
PREPARATIONS BEFORE USING
B. Intro Scan
In STOP mode
Battery Installation
•
•
•
Press the MODE button three times.
The INTRO indicator will appear in the display.
Press the PLAY button to play the first 10 seconds of each track on the disc.
1. Open Battery Compartment cover.
2. Insert 2 batteries (LR6, “AA” size, or equivalent)
in the correct polarity as indicated.(Batteries not included)
(Heavy duty batteries are recommended.)
3. Close the cover properly.
NOTE - To cancel INTRO SCAN simply press the MODE button until the INTRO indicator disappears.
C. Random Play
In STOP mode
AC Power Adaptor
1. Plug the DC output of the adaptor to the DC Jack.
•
•
•
Press the MODE button four times.
The SHUF indicator will appear in the display.
Press the PLAY button, all the tracks on a disc to be played in a random sequence.
2. Connect the adaptor (4.5V/500mA) to a power outlet.(Adaptor not included)
Make sure the voltage is compatible.
NOTE - To cancel RANDOM PLAY simply press the MODE button until the SHUF indicator disappears.
DISC PLAYING
Program Play
This CD player is designed to play the 8cm and 12cm compact disc without using adaptor.
1. Press the PROG button when the unit is in the stop mode until PGM show on the display.
2. Press
or
to select the desired track.
Getting Start
3. Press the PROG button to enter the track into memory. The program numbers which will be
incremented one step.
4. Repeat step 2 and 3 to program the order of more tracks can be programmed into memory.
1. Insert the headphone/earphone plug to PHONE JACK.
2. Push the OPEN button to right, and then the door open, put a disc into the CD
compartment with label side upward.
5. Press
to start the program play.
3. Push the disc gently around the centre area until it clicks so that the disc fits into the
pivot.
6. To erase the program, simply press the
STOP button to turn the power off.
(To remove the disc : Pick up the disc, holding the edge, while pressing the pivot gently.)
4. Close the door and press the PLAY/PAUSE Button once.
5. The Display will show the total number of tracks of the disc, then begin to play the first
track.
MAINTENANCE
Cleaning the Lens
If the lens becomes dusty, clean it with camera lens blower. Be careful not to scratch the surface of the
lens.
General Operation
Play/Pause Buttons
—
—
Press once to start playback in the original order.
Press again to stop the disc play temporarily.
Press once to stop playback.
Cleaning the Cabinet
From time to time, clean the cabinet with a soft dry cloth. For more stubborn stains, slightly moisten the
cloth with water or a mild detergent solution. Never use benzene, alcohol or other solvents as they may
damage the finish of the cabinet.
Stop Button
Press again to turn off power
Skip / Search Buttons
—
—
Press once to skip to next track
track
Press continuiously to search forward
or backward
or back to previous
.
SPECIFICATIONS
.
Output Power
Freq. Response
:
:
20MW (32
100 ~ 20000 Hz
)
Various Playing Modes
MODE Button — There are 3 kind of function :
Power
Dimensions
:
:
DC 4.5V external and size “AA” batteries, UM-3, HP-7, R6, 1.5V x 2
146mm(W) x 146mm(D) x 27mm(H)
A. Repeat Play
During PLAY mode
•
•
Press the MODE button once to play single track repeatedly.
The repeat indicator will appear in the display.
1
During PLAY mode
•
•
Press the MODE button twice to play the entire disc repeatedly.
The repeat indicator ALL will appear in the display.
NOTE - To cancel REPEAT simply press the MODE button until the repeat indicator disappears.
— 3 —
— 4
—
|