SRCD858
MW
INSTRUCTION MANUAL
WARNINGS
TO Prevent fire or shock hazard, do not use this plug with an extension cord, receptacle or add other
outlet unless the blades can be can be fully inserted to prevent blade exposure. To prevent fire or shock
hazard, do not expose this appliance to rain or moisture.
WARNING
The lightning flash with arro-
whead symbol,within an equ-
ilateral triangle is intented to
alert the user to the presence
of uninsulated' dangerous vo-
ltage' within the product's en-
closure that may be of suffici-
ent magnitude to constitute a
risk of electric shock to perso-
ns.
CAUTION : TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (
OR BACK),NO USER SERV-
ICEABLE PARTS INSIDE R-
EFER SERVICING TO QUA-
LIFIED SERVICE PERSON-
NEL
The exclamation point within
an equilateral triangle is int-
ended to alert the user to the
presence of important opera-
ting and maintenance (servi-
cing) instructions in the liter-
ature accompany-ing the ap-
plicance
IMPORTANT SAFETY INSTRUCTIONS
Read these instruction.
1
2 keep these instructions.
3 heed all warnings.
4 Follow all instructions.
5 Do not use this product near water(swimming pool, beach, lake etc.).
6 Clean only with a dry cloth.
7 Do not block any of the ventilation openings.Install in accordance with the manufacturer's instructions .
8 Do not install near any heat sources such as radiators, heat registers . Stoves or other apparatus
(including amplifiers)that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug, A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at receptacles and the point
where they exit from the stereo.
11 Only use attachments/accessories specified by the manufacturer.
12 Unplug this apparatus during lightning storms or when unused for long periods of time
13 Refer all servicing to qualified service personnel. Servicing is required when the system has been
damaged in any way, such as a damaged power-supply cord or plug . Has been exposed to rain or
moisture ,does not operate normally , or has been dropped.
14 This appliance should not be exposed to dripping water or splashing water and objects filled with
water, such as vases, should not be placed on this unit
- 1 -
IMPORTANT NOTES
•
•
Operate controls and switches as
described in the manual.
Before turning ‘On’ the power, make
certain that power cord is properly
installed.
Store your CDs, in a cool area to avoid
damage from heat.
When moving the set, be sure to first
•
•
Avoid installing this unit in places
exposed to direct sunlight or close to heat
radiating appliances such as electric
heaters, on top of other stereo
equipment that radiates too much heat,
places lacking ventilation or dusty areas,
places subject to constant vibration and/
or humid or moist areas.
•
•
Do not attempt to clean this unit with
chemical solvents as this might
disconnect the power cord.
damage the finish. Use a clean dry cloth.
CLASS 1 LASER PRODUCT
CAUTION
INVISIBLELASERRADIATION
WHENOPENANDINTERLOCKS
DEFEATED.
CLASS1LASERPRODUCT
APPAREILÁLASERDECLASSE1
PRODUCTOLASERDECLASE1
AVOIDEXPOSURETOBEAM
This product contains a low power Laser Device.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
- 2 -
UNPACKING AND SET-UP
•
•
•
Carefully remove the unit from the carton and remove all packing material from the
unit.
Remove any labels or stickers which may be on the front or top of the set, but do not
remove any labels from the back or bottom.
We suggest that you retain the original carton and packing materials in case it ever
becomes necessary to return your unit for service. This is the only sure way to
protect the unit from damage in transit.
•
•
•
Remove any small strips of tape that may have been used to prevent the CD door
from opening in transit.
Unwind the lead wire FM antenna on the back of the unit and extend it to its full
length.
The unit is shipped with a dummy CD display card in the CD player. This dummy CD
card must be removed before you can use the CD player.
SPEAKER CONNECTION
Connect each speaker to the corresponding speaker jack on the back panel of the main
unit. Make sure that the left speaker plug is connected to the left (L)speaker jack and the
right speaker plug is connected to the right (R) speaker jack.
POWER SOURCE
This system is designed to operate on 120V 60Hz AC house current. Connecting this
system to any other power supply could result in damage to the unit which is not covered
by your warranty. You will note that this system is equipped with a polarized AC power
plug having one blade wider than the other. This is a safety feature. If this plug does not fit
into your existing AC outlet, do not try to defeat this safety feature by filing the wide blade
to make it fit into your outlet. If this plug will not fit into your outlet, you probably have an
out-dated non- polarized AC outlet. You should have your outlet changed by a qualified
licensed electrician.
AC OPERATION
1.) Unwind the AC Power Cord completely.
AC
Outlet
2.) Insert the plug into any convenient
120V 60Hz AC outlet.
AC
Plug
- 3 -
PROTECT YOUR FURNITURE
This model is equipped with non-skid rubber ‘feet’ to prevent the product from moving
when you operate the controls. These ‘feet’ are made from non-migrating rubber material
specially formulated to avoid leaving any marks or stains on your furniture. However
certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may
cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture.
To prevent any damage to your furniture we strongly recommend that you purchase small
self-adhesive felt pads, available at hardware stores and home improvement centers
everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you place
the product on fine wooden furniture.
- 4 -
LOCATION OF CONTROLS
22 20
19
21
18
1
2
3
17
16
4
6
5
15
14
13
12
7
8
9
10
11
- 5 -
LOCATION OF CONTROLS
1. STANDBY Button
Rear of Unit
2. REMOTESensor
3. PROGRAMButton
4. LCDDisplay
23. AC Main Lead
24. Speaker Sockets
25. FM Antenna wire
5. CD REPEAT Button
6. Radio Dial Scale
7. FUNCTIONSelector
8. HEADPHONESSocket
9. RADIOBANDSelector
10. CASSETTECompartment
11. CASSETTE keys
RECORD, PLAY , FAST REWIND,
FAST FORWARD, STOP / EJECT,
PAUSE
12. DISCButton
13. CD PLAY/PAUSE Button.
14. TUNINGKnob
15. CD STOP Button
16. BASS BOOST Button
17. VOLUMEControlButtons
18. CDTray
19. CDSKIP/SEARCH
ForwardsButton
20. CDSKIP/SEARCHBackwards
Button
21. FMStereoIndicator
22. MUTEIndicator
- 6 -
PREPARATION FOR USE
Remove the stereo carefully from the box, retaining the packaging for future use.
Read these instructions carefully before use.
CONNECTIONS
Before switching on your stereo system, be sure that it is connected as follows:
SPEAKERS
Connect the speakers to the speaker sockets on the back of the music system.
Connect the left speaker to the left speaker socket and the right speaker to the right
speaker socket.
Connect the Mains Lead to an AC outlet.
Insert two R03S (AAA or equivalent) batteries into the battery compartment of the
remote control (Batteries are not included).
You are now ready to switch on the power.
LISTENING TO THE RADIO
OPERATION
Press the STANDBY Button to turn the unit on, the Stand-By indicator will go out.
Select the Function Selector to TUNER and turn the radio band selector to AM or
FM STEREO position.
Tune into the station using the TUNING knob.
Adjust the VOLUME to the desired level using the VOLUME Control Button.
To turn off the radio, press the STANDBY Button.
HANDLING COMPACT DISCS
To remove a disc from its storage case, press down on the center of the case and lift the
disc out, holding it carefully by the edges.
Fingerprints and dust should be carefully wiped off the disc's recorded surface with a
soft cloth. Unlike conventional records, compact discs have no grooves to collect dust and
microscopic debris so gently wiping with a soft cloth should remove most particles. Wipe
in a straight line from the inside to the outside of the disc. Small dust particles and light
stains will have absolutely no effect on reproduction quality.
Never use chemicals such as record sprays, antistatic sprays, benzine, or thinners to
clean compact discs. These chemicals can irreparably damage the disc's surface.
- 7 -
Discs should be returned to their cases after use. This avoids serious scratches that
could cause the Laser pickup to skip.
Do not expose discs to direct sunlight, high humidity, or high temperatures for extended
periods. Long exposure to high temperatures can warp the disc.
LOADING DISCS
LOADING AND UNLOADING COMPACT DISCS
Set the FUNCTION Selector to the CD position.
Open the disc compartment.
Once the CD cover has opened, remove a disc from its case and place it carefully in
one of the indentations in the compartment with the label side facing up. Smaller, 3”
discs, may also be used with this CD player.
To load additional CD's press the DISC button to rotate the CD tray. Up to 3 discs
can be placed in the tray at any one time. Smaller 3 inch discs can be used in this
unit.
Close the disc compartment.
The unit will go through a cycle to find the first CD there is in the tray. This may take
up to 15 seconds.
The disc compartment may be opened at any time.
CAUTION
Do not put anything except a compact disc into the compartment. Foreign objects
can damage the mechanism.
Do not force the compartment by hand during the opening and closing operations.
Keep the disc compartment closed when not in use to prevent dirt and dust from
entering the mechanism.
SUPER BASS
To enhance Bass effect to the desired level using the Bass Control Button.
PLAYING DISCS
Open the disc compartment, and load a CD.
Close the disc compartment and the unit will search for the first tray to contain a CD
and the display will show the total playing time of the CD.
Press the CD DISC Button to select the CD of your choice.
Press the PLAY/PAUSE Button and disc play will begin from the beginning of the
first track.
A particular track can be selected by pressing the ꢀ & ꢁ Buttons. If this is done
before pressing the PLAY/PAUSE Button, disc play will start with the selected track
when the PLAY/PAUSE Button is pressed.
At the end of the disc, the unit will switch to stop mode
- 8 -
Notes:
If the disc is deeply scratched, or too dirty, disc play may not start.
If an improperly centered disc is played, noise can be heard in the
mechanism. The use of such discs should be avoided.
IMPORTANT INFORMATION
This compact disc player has built-in error compensation circuits to correct minor
defects in a disc. There are limits, however, to the amount of corrections available.
In some cases, the CD player may skip some tracks on a disc during disc play. This
problem may be caused by defects (such as scratches) in the disc being played
which are too large for the error compensation circuits to handle. If you encounter
this problem, check the CD player's operation as follows, before having the unit
serviced.
Play a new disc. If the CD player operates normally, the skipping problem is probably
due to a defective disc.
TO STOP A CD PART WAY THROUGH
Press the STOP Button. Disc play will stop, the display will show the total number of
tracks and the total playing time of the CD.
To temporarily stop disc play (pause mode), press the PLAY/PAUSE Button. Disc
play will pause at the current play position.
To resume disc play, press the PLAY/PAUSE Button again. The Play indicator will
be displayed.
TRACK SKIP
TO SKIP TO THE NEXT TRACK ON A DISC
For example, to skip ahead to the beginning of track 5 while track 4 is playing:
Press the ꢁ Button once. Disc play will resume at the beginning of track 5.
The CD player will skip ahead to the next track each time the ꢁ Button is
pressed. Repeatedly pressing the Forward Skip Track Button makes the CD player
skip ahead through the disc track by track. Once the beginning of the last track
is reached the CD player will not advance any further.
TO SKIP BACK TO THE PREVIOUS TRACK ON A DISC
For example to skip back to the beginning of track 3 while track 4 is playing:
Press the ꢀ Button twice. Disc play will resume at the beginning of track 3.
The CD player will skip back one track each time the ꢀ Button is pressed. If this
Button is pressed once in the middle of a track, the CD player will skip back to the
beginning of that track. To make it skip back to the previous track press the ꢀ
Button twice.
Repeatedly pressing the ꢀ Button makes the CD player skip back through the disc
track by track. Once the beginning of the first track is reached, the CD player will
not go back any further.
- 9 -
Notes:
The ꢁ & ꢀ Buttons can be used to select a desired track to play before
disc play starts. In this case the number of the selected track will be displayed until the
Play/Pause Button is pressed.
DISC SKIP
To skip to the next disc simply press the DISC SKIP Button. The unit will cycle
through position 1 - 2 - 3 - 1 - 2 . . . . . .etc
REPEAT DISC PLAY
If the REPEAT Button is pressed during normal or programmed disc play the following
repeat functions are displayed in sequence in the CD Display.
REPEATALLDISC
REPEAT1DISC
REPEAT1
Repeats All the Tracks on All the Discs
Repeats all the tracks on the Current disc.
Repeats the current track on the Current disc.
To cancel a repeat mode, keep pressing the REPEAT Button until the REPEAT Indicator
disappears.
PROGRAMMED DISC PLAY
It is not possible to enter programs during disc play. Press the STOP Button first,
then follow the instructions below.
ENTERING A PROGRAM
1.
Press the PROGRAM Button and the CD Display will display the word
Progam edit and 01 d:--
2.
3.
Select the disc that the first track is on using the Disc Skip Button.
Select the desired track using the Track skip buttons until the desired track
is reached and the display will show Progam edit and
01 d2:04.
4.
5.
Press the PROGRAM Button once again and the selected disc and track
number is then stored in memory. The CD Display will change to Progam
edit and 02 d2:--
Repeat steps 2 - 4 to enter additional tracks. You can store up to 32
programs in memory.
Notes:
If the PLAY/PAUSE Button is pressed before the PROGRAM Button is
pressed to store a track, the track will not be programmed and the disc
will start playing from the first selected track.
Any track can be programmed to play more than once.
If you press the STOP Button during PROGRAM mode, the entire program
will be erased from memory.
- 10 -
LISTENING TO PROGRAMMED TRACKS
Program your selection of tracks by following the procedure shown above.
Press the PLAY/PAUSE Button.
Disc play will start at the beginning of the first programmed track.
TO CLEAR THE PROGRAMMED MEMORY
If the disc is playing, press the STOP Button.
Press the STOP Button again. All the programs will then be erased from memory.
The program memory will also be cleared if the Function Selector is changed to
another function, or if the power is switched off.
LISTENING TO TAPE
INSERTION AND REMOVAL OF CASSETTES
Press the Stop/Eject Button to open the Cassette Door.
Slip your cassette tape into the cassette door with the exposed section of tape at
the bottom and the playback side facing you.
Close the Cassette Door securely before starting.
When finished, press the STOP/EJECT Key to open the Cassette Door, and retrieve
your cassette tape.
PLAYING TAPES
Select the TAPE Option using the FUNCTION Selector.
Insert your cassette tape.
Press the PLAY Key to start the tape.
Use the PAUSE Key whenever you want to suspend playback.
Press the STOP/EJECT Key when finished.
RECORDING
RECORDING FROM THE RADIO
Select the AM or FM STEREO Option using the FUNCTION Selector.
Tune in your station and insert a cassette tape into tape deck.
Press the RECORD Key and the PLAY Key at the same time to start recording.
Press the STOP/EJECT Key when finished.
RECORDING FROM CD
Select the CD Option using the FUNCTION Selector, and insert your disc.
Press the RECORD Key and the PLAY Key at the same time to start recording.
Press the CD PLAY/PAUSE Button to start the disc.
Press the STOP/EJECT Key when finished.
- 11 -
COPYRIGHT NOTICE WARNING
Most records, compact discs, audio and video cassettes, radio and television broadcasts
contain material which is subject to copyright laws. It is unlawful to record such material in
any form whatsoever, whether on disc or tape, without the permission of the copyright
owner concerned. Any person who makes a recording of such material without the
consent of the copyright owner infringes on copyright laws and may be liable to pay
substantial damages to the copyright owner, and in some cases subject to criminal
prosecution.
HEADPHONES
Headphones should have a 3.5 mm diameter stereo plug with an impedence of 8-32 ohms.
When headphones are connected, the speakers are automatically disconnected.
- 12 -
REMOTE CONTROL
1.
2.
3.
4.
5.
6.
7.
8.
STANDBY Button
STOPButton
PLAY / PAUSE Button
CD SKIP Buttons
PROGRAMButton
DISCSKIPButton
MUTEButton
VOLUMEUP/DOWNButtons.
BATTERY INSTALLATION
Insert 2 R03S (AAA or equivalent) size batteries into the battery compartment of the
remote control and replace the cover (Batteries are not included).
BATTERYREPLACEMENT
When the batteries become too weak, the operating distance of the remote control is
greatly reduced and you will need to replace the batteries.
Note:
To maintain the accuracy and long life of the transmitter, do not press two
or more Buttons simultaneously.
If the remote control is not to be used for a long time, remove the batteries
to prevent possible damage through leaking batteries.
Do not mix different types of batteries, or old batteries with new ones.
USING THE REMOTE CONTROL CORRECTLY
Point the remote control at the Remote Sensor.
The functions of the Buttons on the remote control are the same as the corresponding
controls on the main unit.
When there is a strong ambient light source, the performance of the infrared Remote
Sensor may be degraded, causing unreliable operation.
The maximum effective distance for remote control operation is about 5 metres (16.5 feet).
MUTE
Press the MUTE Button on the remote control to switch off the sound, (the MUTE
indicator will light up).
Press MUTE again to restore the sound to the previous level ( the MUTE indicator will
go off.
- 13 -
CASSETTE CARE
Two common causes of trouble experienced when using cassettes are:—
(a) Tape jamming - Leading to uneven speed in playback, and
(b) Tape tangling - Where the tape wraps itself around vital parts of the mechanism.
To reduce the likelihood of these problems occurring, the following
precautions should be observed.
Check that there are no loose layers of tape visible through the
cassette center window (see Fig. 1). Take up any loose layers,
using a pencil or hexagonal barrelled ballpoint pen, before inserting
the cassette into the machine (see Fig. 2).
If the cassette feels "tight" while performing operation shown in Fig.
2, the tape may be jamming due to "ridges" formed in the winding of
the tape (visible through the center window). These may be removed,
in most cases, by fast winding of the cassette from one end to the
other and back again.
Use only well-known brands of tape.
Avoid use of C-120 cassettes.
Furthermore, do not expose cassettes to direct sunlight, dust or oil, and do not touch the
tape surfaces.
HEAD CLEANING
The ta[e heads, pinch roller and capstan require periodic cleaning. This removes particles
of the metal oxide coating that wear off the tape and accumulate on these parts and impair
performance. Switch off the power, press the STOP/EJECT Button to open the cassette
door, and press the PLAY Button. Clean the tape heads, pinch roller and capstan with a
soft cloth or cotton bud dampened in isopropylalcohol or special tape head cleaner.
Erase head
Record/
Capstan
Pinch
Roller
PREVENTION AGAINST ACCIDENTAL ERASURE
To prevent a recording on a cassette tape being erased
accidentally, break off the tab on the rear of the tape, as in the
diagram. Now recording on this side is no longer possible. You
can render this protection ineffective by covering the hole with
a piece of adhesive tape.
TAB FOR SIDE A
- 14 -
MAINTENANCE AND CARE
Electronic products of this kind should never be subjected to extreme temperatures or high
humidity. For instance, this set should not be placed in bathing areas or around stoves and
radiators.
If necessary, clean the unit with a piece of cloth dampened with water only (Be sure the
AC Power Cord is disconnected from the Mains). Never use a polish or a strong detergent
as this will damage the finish of the cabinet.
This equipment has been designed and manufactured to meet the highest international
standards, but, like any electrical apparatus which is operated at mains voltage, care must
be taken if you are to obtain the best results and safety is to be assured. This is
particularly important with audio equipment.
DO. . .
Read the operating instructions before you attempt to use the equipment.
DO. . .
Ensure that all electrical connections (including the mains plug, extension leads
and interconnections between pieces of equipment) are properly made and in
accordance with the manufacturer's instructions. Check that the mains fuse
rating is correct.
DO. . .
Always consult your dealer if you are ever in doubt about the installation,
operation or safety of your equipment. He is the best person to advise you.
DON'T. . .
Obstruct the necessary ventilation - especially DON'T stand the set close to
curtains or on soft furnishing such as carpets. Overheating can cause
unnecessary damage and shorten the life of the set.
Remember that to obtain the best performance and lasting satisfaction from your
equipment, have it regularly checked by a reliable service organization. Ensure that it is
correctly used by all family members.
ABOVE ALL. . .
Never let children push anything into holes or slots in the case - this could result in an
electric shock.
- 15 -
SPECIFICATIONS
Power Supply
AC:
120V ~ 60 Hz
Radio Frequency Coverage
FM:
88 - 108 MHz
AM:
530 - 1710 kHz
Recording System
Recording System:
Erasing System:
DCBias
Magnetic Erase
General
Speaker Impedance
Headphones:
8 Ohms
3.5mm stereo jack plug, 8-32 Ohms
CD Player
PickUp:
3-Beam, Semiconductor Laser
16-Bit Linear 2x Oversampling
Encoding:
Due to continuing improvements, the features and design are subject to change without notice.
For service assistanceand product information, please call: 1-800-968-9853.
- 16 -
MADE IN CHINA
|