&
2356, 2358, 2359 2360
Instruction Manual
DELUXE MIXMASTER MIXER
®
Instruzioni per l'Uso
DELUXE MIXMASTER MIXER
®
Mode d'Emploi
BAT TEUR DELUXE MIXMASTER
Gebrauchsanleitung
DELUXE MIXMASTER MIXER
®
®
Manual de Iinstrucciones
BATIDORA MIXMASTER® DELUXE
Anvandarhandledning
DELUXE MIXMASTER MIXERN
®
Do not place Mixer or bowls on or near a hot gas or
electric burner, or in a heated oven.
12. Do not use Mixer for other than intended use.
13. Do not leave Mixer unattended while it is operating
UNIT FOR
USE
When your
Mixer is first used, you may experience
an odor and possibly a slight wisp of smoke from your mixer motor.
This is caused by the heat curing of the insulation which protects the
motor and is normal. After the first few uses, this effect will disappear.
FOR PROOUCTS PURCHASEO IN
reduce the risk of electrical
CANADA ONLY:
this appliance
T
O
has a polarized plug (one blade is wider than the other). As a
safety feature, this plug will fit in a polarized plug only one way.
If the plug does not fit fully in the outlet: reverse the plug.
If it still does not fit, contact a qualified electrician.
00 NOT ATTEMPT TO OEFEAT THIS SAFETY FEATURE.
FEATURES
The Mix-Finder® dial tells you at a glance
which mixing speed to use. No problem
ejecting the beaters either – just push
the ejector button beside the handle.
When making bread, the Sunbeam®
Deluxe Mixmaster® electronically
controls the speed of the dough hooks
to deliver just the right power for proper
kneading action.
®
Thank you for choosing the Sunbeam
Deluxe Mixmaster® Mixer. For generations we
have been helping cooks prepare moist
cakes, light and fluffy meringue, and chewy
cookies. You can even make bread with your
Sunbeam Deluxe Mixmaster® Mixer.
®
The Sunbeam® Deluxe Mixmaster®
Mixer offers you a choice of 12 different
mixing speeds. The bowl-fit beaters
and bowls have been designed to mix
ingredients thoroughly and evenly.
You’ll love being able to make so many
things with your mixer!
11
1
2
3
10
9
8
7
4
5
6
1. Beater Ejector
6. Dough Hooks
11. Mixing Guide
2. Large Mixing Bowl
3. Small Mixing Bowl
4. Bowl-Fit Beaters
5. Turntable
7. Stand
Some models do not have
the worklight feature.
8. Worklight
*
*
9. Mixer-Release Trigger
10. Mix-Finder® Dial
3
As you release the mixer-release trigger,
the top of the top of the trigger should
clamp around the metal pivot.
ASSEMBLING THE STAND MIXER
Before assembling the mixer, be
sure the Mix-Finder® dial is in the
ZERO position and the electric cord
is unplugged.
For models equipped with a head-lock
feature–To lower the mixer-head for
normal operation, support the mixer
head with one hand. Then press in on
the head-lock latch. Gently lower the
mixer head until the mixer head is in a
normal operating position.
ATTACHING THE TURNTABLE
Place the revolving turntable into
the base of the stand using the socket
corresponding to the size of the bowl.
Latched Opening
Ball Bearing
Extension
Mixer-Release
Trigger
Large
Small
Bowl
Bowl
Be sure the mixer head is securely
attached to the stand before using.
ATTACHING THE MIXER HEAD
Press in on the mixer-release trigger,
located at the rear of the stand.
NOTE: This mixer is NOT intended
for use away from the stand.
For models equipped with a head lock
feature – While pressing in on the
mixer-release trigger, press in on the
head-lock latch. This is best
accomplished by using the thumb and
forefinger of the same hand and
pressing inward.
ADDING THE MIXING BOWL
Place the desired mixing bowl onto
the turntable so that the groove in the
bottom of the bowl fits into the correct
groove in the turntable.
This will open the top of the stand to
receive the mixer head. Place the mixer
head on the top of the stand so that the
metal pivot, located on the bottom of
the mixer head, goes into the open
groove on the top of the stand.
Mixing bowls should NEVER be used in
a conventional oven, microwave oven,
on top of the range, or on any other
heated surface.
NOTE: If mixing bowls are scratched
or chipped, do not use mixer. Mixer
bowl should not be used to blend in
hot liquids.
Mixer
Head
Metal
Mixer-Release
Pivot
Trigger
Stand
4
Attaching the Beaters
Be sure the Mix-Finder® dial is in the
ZERO position and unplug electric cord
from the electrical outlet.
Side of
Bowl
Lift mixer head up and back to pull it
out of the way of the bowl, while
holding in an upright position.
Conical Square
Beater
Beater
Insert the beaters, one at a time,
using a combination pressing and
twisting motion, until the beaters
snap into position.
If a beater should not properly snap
into place, pull it out of the socket
and rotate it one quarter turn.
Reinsert the beater into the socket
until it snaps into position.
NOTE: It is important that the beaters go
into the correct sockets. Otherwise the
mixer will not give you the proper
mixing action. Do not risk ruining a
recipe or damaging your mixer. Read
the following instructions carefully.
Attaching the Dough Hooks
Set the Mix-Finder® dial in the OFF
position and unplug the electric cord
from the electrical outlet.
One of the beaters is conical in shape
and has a nylon button on the bottom.
It goes into the socket on the side of
the mixer nearest the side of the bowl.
The other beater is square-shaped and
goes into the socket nearest the center
of the bowl. See beater symbols located
on the front of the mixer head.
Lift mixer head up and back to tilt it out
of the way of the bowl, while holding in
an upright position.
NOTE: The dough hooks must go into
the correct sockets. The mixer will
operate with the dough hooks in the
wrong position. However, you will not
get proper kneading action and you
could risk ruining a recipe or damaging
your mixer. Read the following
Square
Beater
instructions carefully.
Conical-Shaped
Beater
Nylon
Button
5
The dough hook with the small washer
and foot goes into the socket on the
side of the mixer nearest the side of
the bowl. The other dough hook with
the large washer goes into the socket
nearest the center of the bowl. See the
dough hook symbols located on the
front of the mixer head.
About the Worklight Feature
Some of our models have a
worklight that lights the area
inside the mixing bowl.
As soon as the electric cord is
plugged in, the worklight will glow.
It will continue to glow until the
electric cord is unplugged from
the electrical outlet.
Worklight
Beater-Bowl Drive Adjustment
Operating Instructions
Automatic bowl rotation is factory set.
Occasionally, a simple adjustment
may be necessary when the bowl
fails to rotate.
About the Mix-Finder® Dial
The Mix-Finder® dial is used for turning
the mixer ON and OFF and for selecting
its 12 mixing speeds.
To make this adjustment, tilt the mixer
head back. Hold the mixer head in an
upright position and locate the
Rotate the Mix-Finder® dial in a clockwise
direction, to increase mixing speed;
and in a counterclockwise direction,
to decrease mixing speed.
As you rotate the Mix-Finder® dial,
notice that a numbered speed
is aligned with the indicator on top
of the mixer head. This numbered
speed indicates the speed at which
the mixer is operating.
adjustment screw on the underside
of the mixer head. Loosen the locking
nut and turn the adjustment screw on
the underside of the mixer head.
Loosen the locking nut and turn the
adjustment screw clockwise, to lower
the mixer head; or counter clockwise,
to raise the mixer head. Retighten the
locking nut. The beater with the nylon
button should lightly touch the bottom
of the mixing bowl.
Rotate the Mix-Finder® dial until the
indicator is opposite the numbered
speed you wish to use.
Locking
Nut
Adjustment
Screw
Speed
Indicator
Mix-Finder®
Dial
Mixing
Guide
6
Mixing Guide
The mixing guide on your mixer has been designed to help you take the guess work
out of preparing foods.
Next to each of the numbered speeds on the Mix-Finder® dial are descriptions
of the mixing task best suited to that mixing speed. Use those descriptions as
a mixing guide when preparing your favorite recipes.
Speed
Setting
Mixing
Guide
Example
1
Fold-Kneaded Use when mixing dry ingredients or when folding
two portions of a recipe together, such as a beaten
egg white into a batter or when directions call for
LOW speed. Use for kneading bread.
2
3
Stir
Use when stirring liquid ingredients or when gentle action
is needed to moisten dry ingredients.
Blend
Use when quick breads require a brisk action,
just enough to blend ingredients but not enough
to develop a smooth batter.
4
Mix
Use when mixing dry ingredients and liquid ingredients
together alternately in a recipe.
5
6
Combine
Use when recipe calls for combining ingredients together.
Cake Mixes Use when preparing packaged cake mixes or
when directions call for MEDIUM speed.
7
8
9
Cream
Whip
Use when creaming sugar and butter together.
Use to whip potatoes or to develop a smooth batter.
Whip/Cream Use to whip whipping cream or to develop a light,
fluffy texture.
10
11
12
Desserts
Frostings
Use to beat air into whipped desserts.
Use when preparing light, fluffy frostings and candies.
Egg Whites Use when aerating eggs and egg whites.
Use when directions call for HIGH speed.
NOTE: Due to variations in ingredient temperatures and quantities, the Mixing Guide
speeds are only suggested. If necessary, adjust speeds as needed to achieve
desired results.
7
To remove the worklight lens, place
the Mix-Finder® dial in the ZERO position
and unplug mixer from electrical outlet.
Remove beaters or dough hooks
from mixer sockets and remove
bowl from turntable.
CARING FOR YOUR MIXER
EJECTING THE BEATERS OR DOUGH HOOKS
After you’ve finished mixing, turn the
Mix-Finder® dial to OFF and unplug the
electric cord from the electrical outlet.
Push the ejector button located near
the handle to remove beaters or
dough hooks.
Holding the mixer head in an upright
position, use a small screwdriver to
remove the screw holding the
worklight lens in place.
Scrape excess batter off the beaters
using a rubber or plastic spatula. Do not
strike beaters on the rim of the bowl.
Squeeze the worklight lens, as shown,
until the tabs on the lens clear the
housing. Tilt the worklight lens down
and out of the housing.
CLEANING YOUR MIXER
To clean the mixer, wipe the mixer head,
stand, and turntable with a damp cloth,
then dry. DO NOT IMMERSE THE
MIXER HEAD OR STAND IN WATER.
Avoid the use of abrasive cleaners, as
they may mar the finish of the mixer.
Wash the beaters and bowls in hot,
soapy water after each use. Rinse
thoroughly and dry. Beaters and
bowls may also be washed in an
automatic dishwasher.
To clean the worklight lens, wash in
warm, soapy water. Rinse and dry
thoroughly.
To replace the worklight bulb, unscrew
from socket. Replace with new bulb.
CARE AND CLEANING OF THE WORKLIGHT
(For models with worklight feature only.).
The worklight bulb should be replaced
as soon as it burns out. You may also
wish to remove the worklight lens
periodically for cleaning.
8
NOTE: Replacement bulbs may be
purchased from local hardware or
department stores or from your
nearest authorized Sunbeam Service
Center (6 watt maximum bulb
can be used.)
MIXING AND BAKING SUGGESTIONS
• Ingredients should be added to the
mixing bowl as they are specified in
the recipe. When combining dry
and wet ingredients, you may wish
to moisten ingredients on Speed 1
or 2, then turn to the desired
mixing speed.
To replace the worklight lens,
repeat the steps described in
“To remove the worklight lens”
in reverse order.
• Use the mixing speed that is
recommended in the recipe. When
using a recipe that is not in this book,
use the handy mixing guide on the
Mix-Finder® dial of the mixer to help
you find the correct speed to use.
STORING YOUR MIXER
Store the mixer in a dry location,
such as on a counter top or table top,
or in a closet or cupboard.
Place the small mixing bowl inside
the large mixing bowl with the beaters
inserted into the proper sockets.
Place the dough hooks in the
• If times are specified in the recipe,
use them! BE CAREFUL NOT TO
OVERMIX. Overmixing can cause a
mixture to become very tough.
• Should an object, such as a spatula,
fall into the bowl while the mixer is
operating, turn the mixer off
small mixing bowl. Store the bowls
on the turntable. The beaters will help
hold the bowls in position. Wind the
electric cord into a coil, secure it
with a twist fastener.
immediately. Then, remove the object.
• Remove beaters and place in sink
for easy clean-up.
• When preparing your favorite
recipe, DO NOT exceed 3-1/2 cups
of flour grain in a recipe.
MAINTENANCE
The motor of your stand mixer has
been carefully lubricated at the
factory and does not require
any additional lubricant.
Other than the recommended
cleaning and worklight replacement,
no further user maintenance
should be necessary.
Return the mixer to the nearest
Sunbeam Service Center for
servicing or repairs.
9
Combine a small portion of the dry
ingredients with the wet ingredients.
Mix on Speed 6. Continue adding dry
ingredients until the mixture becomes
sticky, then turn to Speed 1. Gradually
add remaining dry ingredients.
BREADS
Special Instructions for Making
Kneaded Breads
When making kneaded breads,
your mixer will require more care
than when making ordinary mixtures,
such as cake batter and cookie dough.
The elasticity of the bread dough
and the shape of the dough hooks
may cause your mixer to do some
unusual things.
If there is high humidity in the air,
it may be necessary to add additional
flour to the recipe. The high humidity
could also extend the amount of time
necessary for baking.
Guide the mixing bowl with your hands.
Use caution to keep hands out of the
way of the dough hooks.
The bowl may tend to rock back and
forth. We suggest that you guide the
bowl with one hand to help control
the rocking action. AVOID GETTING
YOUR HANDS TOO NEAR THE
DOUGH HOOKS!
Do not attempt to scrape the bowl
while the mixer is operating. Stop the
mixer and scrape the sides of the bowl
as necessary. Use a rubber or
plastic spatula only.
The kneading action may cause the
mixer to slide on a slippery work
surface. Be sure the work surface
and rubber feet on the bottom
of the mixer are clean and dry.
DO NOT attempt to feed dough into
the dough hooks with your hands,
a spatula, or any other utensil while
the mixer is plugged into an outlet
CAUTION: Do not use the mixer too near or in operation.
the edge of a table or counter top,
where it could fall off.
If times are specified in the recipe, use
them! BE CAREFUL NOT TO OVERMIX.
Overmixing can cause a mixture to
become tough. We suggest that
your total mixing time should be
6 – 8 minutes.
DO NOT LEAVE YOUR MIXER
UNATTENDED WHEN USING THE
DOUGH HOOKS.
Should an object, such as a spatula,
fall into the bowl while the mixer
is operating, turn the mixer off
Bread Making Instructions
for Dough Hooks
Ingredients should be added to the
mixing bowl as they are specified
in the recipe.
immediately. Then remove the object.
Remove dough hooks and place in
sink for easy clean-up.
10
DOUGH RISING TIPS
HOW TO SHAPE DOUGH FOR A LOAF PAN
A large, well-greased, glass mixing bowl 1. Using a rolling pin, roll dough
is an excellent container in which to
raise or proof yeast dough. The ideal
temperature is 85°F in a draft-free area.
Cover with a light cloth.
into a rectangle.
2. Roll dough into a loaf, starting
from narrow end.
The final rising should be after the
dough has been shaped and placed
on the greased baking sheet or pan
recommended in the recipe. Again,
cover the rising dough and place
in a warm draft-free area.
If you live in a high altitude area, yeast
breads will require a shorter rising time.
Allow the dough to rise only until it has
doubled in size. Slightly less flour
should be used because flour is dryer
at higher altitudes.
3. Flatten ends with sides of hands,
as shown.
How to Punch Down Yeast Dough
1. Plunge fist into center of risen
dough to punch out excess air.
4. Pinch along seam to seal.
2. Fold outer edges over into center.
Turn dough over and let rise until
doubled, if recipe directions
so specify.
5. Fold ends under and place seam-side
down in a well-greased loaf pan.
11
WARRANTY
Sunbeam Products Inc. warrants that, for a period of two years from date of purchase, this product
shall be free of mechanical and electrical defects in material and workmanship. Our obligation
hereunder is limited to repair or replacement, at manufacturers option, of this product during the
warranty period, provided that the product(s) purchased in the United States are sent postage
prepaid directly to:
SUNBEAM APPLIANCE SERVICE STATION
117 Central Industrial Row
Purvis, MS 39475
Answers to questions regarding this warranty or your nearest U.S.A. authorized service location
may be obtained by calling toll free I-800-597-5978 or by writing to Sunbeam
at PO. Box 948389, Maitland, Florida-332794-8389.
-
Consumer Affairs
For products purchased in Canada please return them, postage prepaid, directly to:
SUNBEAM APPLIANCE SERVICE STATION (KND)
Please call 1-800-667-8623 or email us
Answers to questions regarding this warranty or your nearest Canadian authorized service location
may be obtained by calling toll free in Canada l-800-667-8623. For warranty information or an
authorized service location outside of the United States and Canada please see the warranty service
card inserted in the product packaging.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE;
DOING SO MAY DELAY THE PROCESSING OF YOUR WARRANTY CLAIM.
This warranty does not cover normal wear of parts or damage resulting from any of the following:
negligent use or misuse of the product, use on improper voltage or current, use contrary to
operating instructions, or disassembly, repair, or alteration by any person other than an authorized
service center. Product repair or replacement as provided under this warranty is your exclusive
remedy. Sunbeam Products Inc. shall not be liable for any incidental or consequential damages for
breach of any expressed or implied warranty on this product. Except to the extent prohibited by
applicable law, any implied warranty of merchantability or fitness for a particular purpose on this
product is limited in duration to the duration of the above warranty. Some states and provinces do
not allow the exclusion or limitation of incidental or consequential damages, or allow limitation on
how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary state
to state or province to province.
©1997 Sunbeam Corporation or its affiliated companies. All rights reserved.
®
®
®
®
Sunbeam, Mixmaster, Mix-Finder and Burst of Power are registered trademarks
of Sunbeam Corporation or its affiliated companies.
The configuration and/or color combination of the Mixmaster® Mixer are trademarks
of Sunbeam Corporation or its affiliated companies.
Distributed by Sunbeam Products Inc., Delray Beach, Florida 33445, or an affiliated company.
©
1997 Sunbeam Corporation ou ses filiales. Tous droits réservés
®
®
®
®
Sunbeam, Mixmaster , Mix-Finder
,
et Burst of Power sont des marques déposées
de Sunbeam Corporation ou de ses filiales.
La configuration et/ou la combinaison de couleurs du batteur Mixmaster®
sont des marques de commerce de Sunbeam Corporation ou de ses filiales.
Distribué par Sunbeam Products Inc., Delray Beach, Florida 33445, ou de ses sociétés filiales
.
©1997 Sunbeam Corporation o sus compañías afiliadas. Todos los derechos reservados.
®
®
®
®
Sunbeam, Mixmaster , Mix-Finder y Burst of Power son marcas registradas
de Sunbeam Corporation o de sus compañías afiliadas.
La configuración y/o la combinación de colores de la Batidora Mixmaster® son marcas registradas
de Sunbeam Corporation o de sus compañías afiliadas.
Distribuído por Sunbeam Products Inc., Delray Beach, Florida 33445, ou par une de ses filiales
.
©1997 Sunbeam Corporation o società controllate. Tutti i diritti riservati
®
®
®
®
Sunbeam, Mixmaster Mix-Finder e Burst of Power sono dei marchi registrati della
,
®
Sunbeam Corporation o delle società controllate. La configurazione e/o la combinazione di colori della Mixmaster Mixer
sono dei marchi registrati della Sunbeam Corporation o società controllate.
Distribuito dalla Sunbeam Products, Inc. Delray Beach, Florida 33445, o da una società consociata
.
©1997 Sunbeam Corporation oder die angeschlossenen Unternehmen. Alle Rechte vorbehalten.
®
®
®
®
Sunbeam, Mixmaster Mix-Finder und Burst of Power sind eingetragene Warenzeichen der Sunbeam Corporation oder der
,
®
angeschlossenen Unternehmen. Die Konfiguration und/oder die Farbenkombination der Mixmaster Mixer
sind Warenzeichen der Sunbeam Corporation oder der angeschlossenen Unternehmen.
Vertrieben durch Sunbeam Products Inc, Delray Beach, Florida 33445, oder eine angegliederte Firma
.
©1997 Sunbeam Corporation eller närstående bolag. Alla rättigheter förbehålls.
®
®
®
®
Sunbeam, Mixmaster Mix-Finder och Burst of Power är registrerade varumärken
,
tillhörande Sunbeam Corporation eller närstående bolag.
Mixern Mixmaster®'s konfiguration och/eller färgkombination är varumärken
tillhörande Sunbeam Corporation eller närstående bolag.
Distribuerad av Sunbeam Products, Inc., Delray Beach, Florida 33545, eller ett närstående bolag
.
U . S . P a t e n t N o . 4 , 2 7 7 , 1 8 1
P . N . 3 0 0 5 8 - 1 1
|