StarTechcom Computer Drive SDOCK2U313 User Manual

Quick start guide  
USB 3.1 (10 Gbps) dual-bay dock for SATA drives  
SDOCK2U313  
Rear view  
DE: Bedienungsanleitung - de.startech.com  
FR: Guide de l'utilisateur - fr.startech.com  
ES: Guía del usuario - es.startech.com  
IT: Guida per l'uso - it.startech.com  
NL: Gebruiksaanwijzing - nl.startech.com  
PT: Guia do usuário - pt.startech.com  
Packaging contents  
• 1 x USB 3.1 to dual 2.5 in. or 3.5 in. hard drive docking station  
• 1 x USB 3.1 cable  
• 1 x Universal power adapter (NA/UK/EU/AUS)  
• 1 x Instruction manual  
Power adapter port  
USB 3.1 port  
System requirements  
• USB-enabled computer system with an available USB port  
• 2.5 in. or 3.5 in. SATA drive  
Installation  
Connect the docking station  
Warning! Hard drives and storage enclosures should be handled  
carefully, especially when they’re transported. If you’re not careful  
with your drives, you may lose data as a result. Always handle  
storage devices with caution. Make sure that you’re properly  
grounded by wearing an anti-static strap when you install any  
computer component. If an anti-static strap isn’t available, touch a  
large grounded metal surface (for example, the computer case) for  
several seconds to discharge any built-up static electricity.  
Note: To obtain the maximum USB throughput, you must use a  
computer with a USB 3.1 Gen 2 port.  
Supported operating systems are subject to change. For the latest  
requirements, please visit www.startech.com/SDOCK2U313.  
Product overview  
Front view  
1. Connect the external power adapter from the docking station to a  
power outlet.  
2. Press the Power button to turn on the docking station.  
3. Connect the included USB 3.1 cable from the docking station to  
an available USB port on the computer system. Your computer  
can either be turned on or turned off when you connect the USB  
cable.  
HDD2 slot  
HDD1 slot  
HDD2 Eject button  
HDD1 Eject button  
Install a hard drive  
Power button  
1. Carefully align a 2.5 in. or 3.5 in. SATA drive with an HDD slot on  
the docking station, so that the SATA power and data connectors  
on the drive are aligned with the corresponding connectors inside  
of the HDD slot.  
Power and  
activity LED  
2. Insert the 2.5 in. or 3.5 in. SATA drive into an HDD slot.  
3. Press the Power button to turn on the docking station.  
4. After the hard drive is installed and the docking station is turned  
on, your computer automatically recognizes the hard drive and it’s  
accessible as though the hard drive were installed internally in the  
system.  
Note: If your computer doesn’t automatically recognize the drive,  
it’s likely that your hard drive wasn’t initialized or it was formatted  
incorrectly.  
*actual product may vary from photos  
For the latest information, technical specifications, and support for  
this product, please visit www.startech.com/SDOCK2U313.  
Manual Revision: 04/22/2015  
 

Sharp Cell Phone GT I9000 User Manual
Sharp Convection Oven R 1870 User Manual
Shure Microphone 27C687 User Manual
Sony Laptop PCG F630 User Manual
Sony MP3 Docking Station RDPXF100IP User Manual
Star Micronics Printer SG 10 User Manual
Sterling Plumbing Door 5970 User Manual
Sylvania TV VCR Combo 6313CEY User Manual
Symphonic DVD VCR Combo SD7S3 User Manual
Targus Mouse 400 0088 001A User Manual