S K 6 F
P R O F E S S I O N A L M I X E R
OWNER’S MANUAL
STANTON MAGNETICS, LLC
[email protected] • (954) 929-8999
w w w . s t a n t o n m a g n e t i c s . c o m
© 2001, Stanton Magnetics, LLC
DESCRIPTION OF FUNCTIONS
1. Mic level: Controls the
overall microphone output
level.
user to preview a mix.
the master output
between channels 1 and
2.
phono signal inputs for
channels 1 and 2.
10. Power indicator:
Blue LED indicates
whether mixer is ON or
OFF.
27. Microphone input:
1/4” connector
2. Send: Controls the
level of the effect send
output. this is used to set
the level of the signal
going to the outboard
effects processor or
stomp box.
18. Cue select: In "CUE"
position, the pre-selected
signal of control (9) will be 28. Ground posts :
monitored as a stereo sig- Connect to the turntables’
nal in the headphones. In ground connectors to
"MASTER" position, the
pre-selected signal of
controls (13) and (17) will
be monitored as a stereo
signal in the headphones.
11. Input selector
switches: Selects phono
or line inputs. FLASH™
position allows users to
quickly trigger the phono
input.
eliminate electrical hum.
Ground connectors are
usually supplied with
turntables.
3. Return: Controls the
level of the effect return
input. This is used to
control the level of the
processed signal going
back into the mixer
12. Input Fader Reverse:
Reverses the direction of
each respective input
channel fader. Includes
bi-color LED to indicate
the status of the reverse
function. When LED is
green, the fader is nor-
mal. When LED is red,
the fader direction is
reversed.
29. Send & return con-
nections: The send out-
put is used to connect the
mixer to the line input of
your effects processor or
sampler. The return input
is used to feed the signal
back from the line output
of the outboard unit. This
creates the effects loop.
19. Headphone outputs:
Connection for 1/4” and
3.5mm headphone jacks.
Recommended imped-
ance is 32-200 ohms for
maximum volume.
4. FX: Effect ON/OFF for
each channel, MIC, and
cue.
20. Crossfader Curve
adjustment: Adjusts the
shape of the crossfader
curve from a quick cut for
scratching and cutting to
a longer fade for mixing.
5. Gain: Controls the
input level of each chan-
nel.
30. Program reverse:
Interchanges the outputs
of channels 1 and 2.
13. Channel fader:
Controls the input chan-
nel level.
6. EQ: Individual controls
for low and high frequen-
cy equalization with (+9/-
26 dB) Note: Any
changes made to EQ set-
tings will change the over-
all output level.
21. Crossfader Reverse:
Reverses the direction of
the crossfader.
14. Headphone mute:
Mutes the headphones
without having to change
its level.
22. Power switch:
Selects power "ON" or
"OFF".
7. Master level: Controls
the overall signal output
level.
15. Input Level Meter:
Monitors each channel’s
input level with peak hold
function
23. Power supply con-
nector: Input connection
for the accompanying
power supply.
8. Headphone level:
Controls the overall head-
phone output level. It is
recommended head-
phones with an imped-
ance rating of 200 ohms
or less be used for maxi-
mum volume.
16. Crossfader Reverse
LED: Bi-color LED indi-
cates the status of the
crossfader reverse func-
tion. When LED is green,
the crossfader is normal.
When LED is red, the
crossfader direction is
reversed.
24. Master output: TRS
balanced 1/4” master out-
puts.
25. Outputs: Record out
and unbalanced master
RCA.
9. Cue pan: Fades the
headphone output
between channels 1 and
2, effectively allowing the
17. Crossfader: Fades
26. Inputs: Line and
FADER CLEANING
TECHNICAL SPECIFICATIONS
Line inputs:
Phono inputs:
Send:
Return:
DJ mic input:
Master output:
2 (RCA), 150 mV / 27K ohm
2 (RCA), 3 mV / 47K ohm
2 (1/4”), 150 mV / 27K ohm
2 (1/4”), 775 mV / 1K ohm
1 (1/4 inch), 1.5 mV / 3K ohm
1 (1/4” TRS Balanced/RCA unbalanced),
1.2 V / 100 ohm
1 (RCA), 245 mV / 100 ohm
1 (1/4 inch), 32 - 200 ohms recommended
20 Hz - 20 kHz, +/- 2 dB
+ 9/-26 dB (Hi, Low)
The SK FOUR faders may need lubrication from time to time. This will extend
the fader life and eliminate any potential damage due to extended heavy usage.
Follow the instruction below the lubricate your faders:
1. Remove the 3 fader knobs and
screws located in the corners of the lubricant into both ends of the fader
face plate and take the plate off the and slide the fader back and forth a few
4
3. Spray a small amount of cleaner or
mixer.
times to spread the fluid evenly
throughout the fader.
Record output:
Headphone output:
Frequency Response:
Tone Control :
Gain Control:
S/N Ratio:
2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (remov-
4. Shake and wipe off excess fluid
ing the 2 inner screws will detach the before re-assembling the fader.
fader from the fader plate) and discon-
nect the cable coming from the mixer.
20dB / 1 Khz
Less than 70dB
T.H.D:
Dimension(LxWxD):
Weight:
less than 0.2%
12 3/8” x 10 1/4” x 4” ( 314 x 260 x 102 mm)
7 lbs (3.2 Kg)
ROTATING AND REPLACING THE INPUT SWITCHES
REPLACING INSTRUCTIONS
ROTATING INSTRUCTIONS
1. Remove the PROTEKT™ panel
1 . Remove the PROTEKT™ panel
(Cleaning instructions step 1)
(Cleaning instructions step 1)
WARRANTY
2. Remove the 2 outer screws from
the toggle switch plate (removing the
2 inner screws will detach the switch
from the plate)
2. Remove the 2 outer screws from
the toggle switch plate (removing the
2 inner screws will detach the switch
from the plate)
This unit has been designed and manufactured using quality components.
Therefore, it is warranted to be free from defects in materials (limited as specified
below), and workmanship for a period of twelve (12) months from the original pur-
chase date. During this period, all service and parts necessary to repair a defect
will be free of charge. This limited warranty applies to mechanical parts which are
subject to wear and tear as specified:Faders, specified durability: 15,000 cycles;
Rotary potentiometers, specified durability: 10,000 cycles; Switches, specified
durability: 10,000 cycles. Consequently, the parts listed above are warranted to
be free from defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
3. Remove the switch assembly and
disconnect the cable coming from the
mixer.
3. Rotate the plate to the desired posi-
tion and tighten the screws back in
the top and bottom holes
4. Set the replacement switch assem-
bly in the desired position and place
the screws back in the top and bottom
holes.
For the warranty to be valid, please complete the warranty registration card
attached or fill out the online registration
REPLACEMENT PARTS
To replace the cross or channel faders, follow steps 1 and 2 of the
cleaning instructions. The following replacement parts are available
from Stanton or your local Stanton dealer.
Mail completed warranty cards to:
LF-SK6
Channel fader
Stanton Magnetics, LLC, 2821 Evans Street • Hollywood, FL 33020
CF-SK6
CFF1
Crossfader
Focus Fader
PP-SK6F
PP-SK6F-B
PL-SK6
3PL-SK6
PS-18US
PS-18EU
PS-18UK
Silver face plate
Blue face plate
Two way input toggle switch
Three way input toggle switch with FLASH
US Power Supply (110v)
European Power Supply (220v)
UK only Power Supply (240v)
|