3-800-386-22(1)
Home Theater
Active Speaker System
Operating instructions
SA-VA15
© 1995 by Sony Corporation
TABLE OF CONTENTS
Overview 4
Getting Started
Precautions 6
Unpacking 6
Installing the Speaker Stands 7
Choosing the Best Location 7
Speaker System Hookups 8
Audio Component Hookups 9
Home Theater Operations
Enjoying Surround Sound 10
Adjusting the Surround Sound 11
Adjusting the Sound 12
Using an External Center Speaker 12
Additional Information
Troubleshooting 13
Specifications 13
Glossary 14
Index 14
3
Overview
The SA-VA15 is an active home-theater speaker system
incorporating a Dolby Pro Logic decoder and super
woofer speakers. Its design features include easy
connection to your current TV/VCR setup. You can
connect this speaker system without having to
reconnect the cords of your TV and VCR. Also, you
don't have to connect a center speaker to optimize the
surround effects. Easy operation via the supplied
remote ensures maximum enjoyment of the home-
theater sound this system provides.
Three different types of surround sound
accommodate a variety of program sources
Dolby Surround (Pro Logic) mode
Lets you enjoy superb theater-like presence and
surround effects in your home when playing back
video software encoded with the Dolby Surround
system.
HALL surround mode
Provides a sense of presence similar to that of an open-
air stadium. Ideal for maximum enjoyment of
broadcasts of sporting events like football.
SIMULATED surround mode
Creates simulated stereo surround effects from
monaural sound sources, like old movies or monaural
TV shows.
4
Overview
Built-in center speakers let you enjoy Dolby
Pro Logic Surround sound
Dynamic Bass Roar (DBR) super woofer
system provides theater-like bass sound
The use of a center speaker is a key factor in obtaining
a full surround effect when playing sources encoded
with the Dolby Pro Logic Surround sound system.
Center speakers in a movie theater make central
sounds, such as dialogue, clearer and create a unified
sound image.
To provide a theater-like experience complete with
dynamic bass sounds, this speaker system incorporates
the Super Acoustically-loaded Woofer (SAW) design
(see below) in the left and right front speakers to form
a DBR super woofer system.
Normally, you have to install a center speaker
separately, but this speaker system makes it easy to set
up a high-performance home theater system by
incorporating a high-quality center speaker system into
the front speakers.
Chamber
Drive unit
Main duct
In addition, rear speakers are also provided with this
system to create a complete home-theater that lets you
enjoy the maximum surround effect.
Top view
What is the SAW design?
The SAW design features a centrally-positioned woofer
drive unit, two chamber construction, and a long main duct.
Through precision control of the acoustics of the two
chambers, the unit can reproduce powerful ultra low
frequencies without muddiness.
Center channel
tweeters
In addition, we also included two super woofer modes
designed to bring the dynamic bass sounds found in
movie theaters (mode 1) and concert halls (mode 2) to
your living room.
Front view
Center channel
Full range unit
tweeters
Full range unit
Power turns on and off automatically
The speakers turn on automatically when a sound
signal is input and turn off when you've finished
watching a program and the sound signal goes out. So
you don't have to bother using the power switch every
time you use the system.
Super woofers
Rear speakers
How the center speaker works
The front left and right speakers are equipped with center
channel tweeters (see above) angled inwards at 30° to
reproduce high-frequency center channel sounds. Low-
frequency center channel sounds are mixed with the front
channel signals and reproduced through the front left and
right full range units. This design produces a high-quality
centralized sound image for the center channel which
exactly matches the quality of the front channel sound to
provide superior sound quality and a unified sound image
without a cumbersome external center speaker.
5
Getting Started
Precautions
Unpacking
Check that you received the following items with your
speaker system:
• Front L/R speaker connecting cord, 3.5 m (1)
• Rear speakers SS–SR151 (2)
On safety
• Should any solid object or liquid fall into the cabinet,
unplug the speaker system and have it checked by
qualified personnel before operating it any further.
• Rear speaker connecting cords, 10 m (2)
• Audio connecting cord, 1.5 m (1)
• Remote commander (remote) RM–J15 (1)
• Size AA (R6) batteries (2)
• Speaker Stands (2)
• Screws (8)
On power sources
• Before operating the speakers, check that the operating
voltage is identical with your local power supply. The
operating voltage is indicated on the nameplate on the
rear of the speakers.
• The speakers are not disconnected from the AC power
source as long as they are connected to the wall outlet,
even if the speakers themselves have been turned off.
• If you are not going to use the speakers for a long time, be
sure to disconnect the speakers from the wall outlet. To
disconnect the AC power cord, grasp the plug itself;
never pull the cord.
• One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet only one
way. If you are unable to insert the plug fully into the
outlet, contact your dealer.
Inserting batteries into the remote
Insert two size AA (R6) batteries with the + and – on
the battery compartment. When using the remote,
point it at the remote sensor g on the left front
speaker.
• Should the AC power cord need to be changed, have it
done at a qualified service shop only.
]
}
}
On placement
]
• Do not place the speakers near heat sources, or in a place
subject to direct sunlight, excessive dust or mechanical
shock.
• Good ventilation is essential to prevent internal heat
buildup. Place the speakers in a location with adequate air
circulation, and in a way that does not block the rear
ventilation holes.
When to replace batteries
Under normal use, the batteries should last for about 6
months. When the remote no longer operates the
speakers, replace both batteries with new ones.
On cleaning
• Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
Notes
• Do not leave the remote in an extremely hot or humid
place.
• Do not use a new battery with an old one.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
• If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
For the customers in the USA
For detailed safety precautions, see the “IMPORTANT
SAFEGUARDS” leaflet.
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
6
Getting Started
Installing the Speaker Stands
Choosing the Best Location
Be sure to install the supplied speaker stands before
you use the speakers.
To obtain high sound quality and a proper sound
image from the front speakers, place the speaker with
the built–in operation panel to the left of your TV and
the other to the right of your TV so that the center
channel tweeters angle towards the center of the room.
1
Spread a towel, or other soft cloth, over a table
and lay the speakers down.
For the best central sound image, place the left and
right speakers within 8 feet of each other and
equidistant from the TV.
8 feet (max)
2
Align the pins on the stands with the holes on the
bottom of the speakers.
Speaker stand
Place the rear speakers so that they fire directly across
at each other about 2 to 3 feet above your listening
position.
Bottom of speaker
3
Use a screw driver to fasten the stands to the
bottom of the speakers with the supplied wood
screws (4 for each speaker).
2-3 feet
4
Make sure the stands are securely attached and
stand the speaker upright.
7
Getting Started
Speaker System Hookups
This section describes how to connect the speaker system and how to connect your TV or VCR to the speakers.
The arrow ç indicates signal flow.
Right rear speaker
(SS-SR151)
Left rear speaker
(SS-SR151)
STEP 3
STEP 4
TV
STEP 1
STEP 2
Right front
speaker
Left front
speaker
VCR
1
Twist the speaker cord coating and strip it from
the end of the cords.
STEP 1
Connecting the front speakers
left speaker
right speaker
R-ch SPEAKER
INPUT
2
Insert the stripped wire into speaker terminals.
R-ch SPEAKER
OUTPUT
right
left
To disconnect, pull the
connector out. Never pull
the cord itself.
To connect, depress the
middle of the male
connector until it clicks
into the female connector.
+
R
–
–
L
+
REAR SPEAKERS
+
–
STEP 2
Connecting the rear speakers
Use the supplied speaker cords to connect the rear
speakers to the REAR SPEAKER terminals on the back
of the left front speaker.
Be sure to match the speaker cord to the appropriate
speaker terminal: + (red) to + (red) and - (black) to -
(black). If the cords are reversed, the sound will be
distorted and will lack bass.
For Customers in Canada
Use only the supplied rear speakers SS-SR151.
8
Getting Started
If you have an additional VCR or LD player
Connect it to the 2 IN jacks and connect the 2 OUT jacks
STEP 3 Connecting your TV
to the AUDIO IN jack on the back of your TV.
If the audio and video output jacks on your TV and
VCR are already connected, and your TV has stereo
AUDIO OUT jacks, you can start enjoying surround
sound simply by connecting the speaker system to
your TV as shown below.
STEP 4 Connecting the AC power cord
Connect the AC power cord to a wall outlet.
Important
• Set the volume on your TV to MIN (minimum).
• If your TV has an ON/OFF switch for its internal speaker,
set it to OFF and enjoy the sound from this speaker
system.
Audio Component Hookups
TV
front left speaker
Since this speaker system incorporates its own internal
amplifier and preamplifier, you can also connect an
audio component, such as a CD player.
R
L
OUTPUT
VIDEO
IN
1
CD
OUT
front left speaker
R
AUDIO
L
OUT
R
L
IN
R
L
1
OUT
If you use AUDIO OUT jacks marked VARIABLE
After making the connection as shown above, turn up the
volume on the TV. Use this speaker system‘s volume control
for regular volume adjustment. Turning down the volume
on the TV reduces the AUDIO OUT signal level and may
cause a loss in sound quality and/or the auto-power off
function (see page 10) to activate.
Note
Do not connect an amplified audio source. The combined
amplification from the component and the speaker's internal
amplifier may damage the speakers.
Hooking up the Sony HCD-VA550
For the best possible sound (or if your TV only has a
monaural AUDIO OUT jack, or no AUDIO OUT jacks)
Connect the speaker system directly to your VCR or cable
box.
(Optional Compact Disc Deck Receiver)
1 Connect the LINE OUT FIXED jacks on the HCD-VA550 to
the 2 IN jacks on the left front speaker. Be sure to connect
it to the 2 IN jacks.
The following connections suppress noise from the TV and
let you enjoy high quality sound.
HCD-VA550
front left speaker
R
L
LINE OUT
FIXED
1 Connect your VCR or cable box to the 1 IN jacks on the left
front speaker.
IN
R
L
2
OUT
2 Connect your TV to the 1 OUT jacks on the left front
speaker.
Make sure you use the 1 or 2 IN jacks that correspond to
the VIDEO IN jack you are using on your TV set (i.e.,
VIDEO 1).
2 Connect the CONTROL S OUT jack on the HCD-VA550
component to the CONTROL S IN jack on the front left
speaker.
TV
front left speaker
HCD-VA550
front left speaker
R
L
INPUT
CONTROL S
OUT
VIDEO
IN
1
R
AUDIO
L
OUT
IN
CONTROL S
Notes
• The automatic power on/off function (see page 10) is not
activated by the signal from the HCD-VA550 to prevent
unwanted outbursts of sound.
• See the operating instructions supplied with your HCD-
VA550 for details regarding its operation.
VCR/cable
box
L
AUDIO R
VIDEO
OUTPUT
9
Home Theater Operations
4
Press either DOLBY SUR, HALL or SIMULATED
on the remote, or SURROUND on the operation
panel a few times, according to the program you
want to enjoy.
Enjoying Surround Sound
You can take advantage of the speaker's surround
sound simply by choosing a surround mode according
to the type of program you are watching. This system
is provided with three different surround modes:
program
recent movies
concerts
DOLBY SUR HALL
SIMULATED OFF
r
DOLBY SUR. (Dolby Pro Logic Surround)
Reproduces superb theater-like presence and surround
effects from video software encoded with Dolby
Surround.
r
r
r
r
music
sports
HALL
Provides a sense of presence similar to that of an open-
air stadium. Ideal for maximum enjoyment of
broadcasts of sporting events like football.
old movies
r
monaural TV
programs
r
SIMULATED
education, news
r
Creates simulated stereo sound effects from monaural
sound sources, like old movies or TV shows.
To listen without surround effects
Press SURROUND OFF on the remote, or press
SURROUND on the operation panel a few times until
OFF is displayed.
MUTE
POWER
DOLBY SUR
HALL
SIMULATED
SURROUND OFF
5
Press MASTER VOL. (VOLUME) to adjust the
volume.
To select a suitable SUPER WOOFER mode
Press SUPER WOOFER MODE 1 or 2.
SUPER WOOFER MODE 1 provides powerful bass
sound ideal for movies. SUPER WOOFER MODE 2 is a
more subtle effect designed for music.
SUPER WOOFER
MODE (1,2,OFF)
INPUT 1
INPUT 2
MASTER VOL
To mute the sound
Press MUTING.
To restore the sound, press MUTING again.
AC STANDBY
indicator
(red)
For other sound adjustments, see page 12.
POWER
indicator
(red/green)
The speakers turn on and off automatically
(Auto power on/off function)
Three minutes after the sound signal goes out (when
you turn off the TV, or the currently playing video/
laserdisc ends), the speakers turn off automatically and
the POWER indicator turns red.
The speakers turn themselves back on the next time you
turn on the TV or start playback from the VCR.
SURROUND MASTER VOLUME
POWER INPUT
1
2
3
Press POWER.
The POWER indicator lights (green) and the
speakers turn on. Once you turn the speakers on,
they turn themselves off and on automatically
with the auto power on/off function.
If you press POWER when the speakers are on
They enter standby mode and the auto power on/off
function does not function. You have to press POWER
again to turn on the speakers.
Press INPUT 1 or 2 on the remote or INPUT on
the operation panel to select the program source.
For example, if you connected your VCR to the 1
IN jacks, select INPUT 1.
The respective INPUT indicator lights up.
Note
Some videos and laser discs may use Dolby Surround sound
even if it's not indicated on the package.
Start playback from the program source.
10
Home Theater Operations
Changing the display
To adjust the level
press
You can dim the display, or turn it off, according to
your preference.
between the right and left
front speakers
BALANCE L or R
Press DIMMER a few times until the display mode you
desire appears.
The display returns to full brightness temporarily
when you press one of the buttons on the control panel
or the remote.
of the center speaker
of the rear speaker
CENTER, then press
ADJUST + or –
REAR, then press
ADJUST + or –
4
Press TEST TONE on the remote to turn off the
test tone.
To restore the center,rear, or balance levels to the
factory setting
Press CENTER, REAR, or BALANCE L or R, then press
RESET.
Adjusting the Surround Sound
Although this speaker system is factory preset to
provide balanced surround sound without adjustment,
you can adjust the volume of each speaker and the
delay time to accommodate the conditions in your
living room or your individual preference.
Note
Pressing buttons other than MASTER VOL., RESET,
CENTER, REAR, or BALANCE L or R cancels the test tone.
Adjusting the delay time
By adjusting the delay time you can enhance the spatial
characteristics of the sound to obtain a theater-like
presence regardless of the size of your room. If the rear
speakers are close to your listening position, choose a
longer delay time.
DELAY TIME
TEST TONE
REAR
ADJUST +/–
RESET
CENTER
BALANCE L/R
You can adjust the settings individually for DOLBY
SUR, HALL, and SIMULATED.
1
2
3
Choose any surround mode.
Playback a program.
Adjusting the speaker volumes
The test tone feature lets you adjust the volume of the
sound coming from each speaker to the same level, so
that the surround sound will be even and natural.
Press DELAY TIME on the remote once to display
the current delay time.
Make the following adjustments from your listening
position.
4
Press DELAY TIME a few times to choose the
delay time you prefer, either 15, 20, or 30 ms.
The factory setting is 20 ms.
1
2
Choose the DOLBY SUR mode.
Press TEST TONE on the remote.
The test tone comes from each speaker in
sequence:
To restore the delay time to the factory setting
Press DELAY TIME and then RESET.
/ Left Front (L) / Center / Right Front (R)
Resetting an entire surround mode
Rear ?
Press the button for the surround mode you want to
reset (i.e., HALL) and then press RESET while the
name of the surround mode is being displayed.
All of the adjustments in that mode, including the bass
and treble (page 12), are reset to the factory settings.
3
Adjust the volume levels so that you hear the test
tone from each speaker at the same volume level
when you are in your listening position:
11
Home Theater Operations
Adjusting the Sound
Using an External Center
Speaker
Although this speaker system's sound quality is
already adjusted. You can change the settings, as you
like, for each surround mode individually. The
following settings remain stored in their respective
surround mode until you change them.
Since this system incorporates a center speaker (see
page 5), you don't have to connect a center speaker.
However, it is possible to connect an active center
speaker to the CENTER OUT terminal.
left front speaker
active center speaker
INPUT
OUT
CENTER
DELAY TIME
S. WOOFER
ADJUST +/–
RESET
TEST TONE
REAR
CENTER
BALANCE L/R
If you make this connection, be sure to make the
following adjustments for Dolby Pro Logic Surround.
Connecting a center speaker lets you choose from 4
different Dolby Pro Logic Surround center modes:
NORMAL, WIDE, 3 CH (3 Channel logic), or
PHANTOM. Use the NORMAL or WIDE mode when
center and rear speakers are connected. For details on
Dolby Pro Logic Surround sound, see page 14.
SUPER WOOFER
MODE (1, 2, OFF)
1
2
Playback a program and choose a surround mode.
Make the following sound adjustments according
to your preference and/or the type of program
you are watching.
To
press
adjust the super
woofer level
S.WOOFER,
then press ADJUST + or –
adjust the bass level
adjust the treble level
adjust the balance
BASS, then press ADJUST + or –
TREBLE, then press ADJUST + or –
BALANCE L or R*
SURROUND
CENTER MODE
1
Press SURROUND on the front left speaker to
choose PRO LOGIC. (“PRO LOGIC” appears in
the display instead of “DOLBY SUR” when you
connect an external center speaker.)
* Since BALANCE L and R control sound from the front
speakers, they have little effect on DOLBY SUR when the
source software has a high proportion of center-channel
sound.
2
3
Press CENTER MODE on the front left speaker a
few times until the center mode you want appears
in the display.
To restore the factory settings
Press RESET after pressing either S.WOOFER, BASS,
TREBLE, or BALANCE L or R.
Adjust the speaker volume and delay time, if
necessary, by referring to page 11.
12
Additional Information
General
Specifications
Troubleshooting
Power requirement
Power consumption
120 V AC, 60 Hz
USA: 110 W
Canada: 120 W
If you experience any of the
following difficulties while using
the speakers, use this
troubleshooting guide to help you
remedy the problem. Should any
problem persist, consult your
nearest Sony dealer.
Audio Power Specifications
Dimensions
Approx. 180 x 1040 x
290 mm (w/h/d)
(7 1/8 x 41 x 11 2/5
inches)
Approx. 250 x 1040 x
360 mm (w/h/d,
including speaker base)
(9 6/7 x 41 x 14 5/8
inches)
For front full range/center woofer
speakers: with 8 ohm loads, both
channels driven, from 70 Hz – 20 kHz;
rated 20 watts per channel minimum
RMS power, with no more than 0.9%
total harmonic distortion from 250
milliwatts to rated output.
There’s no sound from any of the
speakers.
Amplifier section
Mass
Front (L): 16 kg
(35 lb 3 oz)
Front (R): 13 kg
(28 lb 9 oz)
Rear: 700 g/pc
(1 lb 9 oz)
/ Check that components are
Continuous RMS
power output
total 100 W
connected securely to the
speakers.
/ Make sure you selected the
correct input (1 or 2).
/ Press MUTING to cancel
the muting function.
/ Press MASTER VOLUME +
to turn up the volume.
Center tweeter
20 W (8 ohms at 10
kHz,10 % THD)
Front full range/
Center woofer
Super woofer
20W + 20W (8 ohms at
1 kHz, 10 % THD)
20 W (8 ohms at 40 Hz,
10 % THD)
Supplied accessories
Rear speakers SS-SR151
(2)
Front L/R speaker
connecting cord, 3.5 m
(1)
Rear
10 W + 10 W (8 ohms at
1 kHz, 10 % THD)
Rear speaker
connecting cord, 10 m
(2)
Audio connecting cord,
1.5 m (1)
Remote Commander
RM-J15 (1)
Sony batteries SUM-3
(NS) (2)
Input sensitivity/
Impedance
450 mV, 50 kilohms
No sound or only a very low sound
level is heard from the rear speakers.
/ Surround sound is turned
Output
1/2: 450 mV, 1 kilohm
Center: 350 mV, 1
kilohm
Rear: Accepts only
supplied rear speakers
SS-SR151
R-ch: Accepts only SA-
VA15 R-ch speaker
with supplied exclusive
speaker cord
off.
/ Adjust the volume of the
rear speakers (see page 11).
/ Check the sound image
balance with TEST TONE
(see page 11).
Severe hum or noise is heard.
/ Move the connecting cord
away from any
Tone control
Front/Center
Bass: ±10 dB at 100 Hz
Treble: ±10 dB at
10 kHz
transformers or motors and
least 3 meters (10 feet) from
any fluorescent lights.
/ Connect the speakers to
your VCR or cable box
instead of your TV
Speaker section
Type
Bassreflex type
SAW type
Bassreflex type
Front speaker
DBR super woofer
Rear speaker
(see page 9).
Speaker unit
Front speaker
system
Center tweeter: 5 cm
cone type (x2)
Front full range/Center
woofer: 10 cm cone
type (x2)
Remote operations cannot be
performed.
/ Point the remote towards
the remote sensor on the
left front speaker.
Super woofer: 13 cm
cone type (x2)
/ Remove any obstructions
between the remote and
this system's left front
speaker.
8 cm cone type (x2)
Rear speaker
/ Replace the batteries in the
remote.
13
Additional Information
• PHANTOM mode
Select PHANTOM mode if you do not
want to use the center speaker to output
sound. The sound of the center channel is
output from the front speakers.
Glossary
Index
Center mode
Front
speaker (L)
Front
A, B
Speaker setting to enhance the Dolby Pro
Logic Surround mode. Select one of the
following four center modes according to
your speaker system.
speaker (R)
Adjusting
bass 12
delay time 11
speaker volume 11
super woofer level 10, 12
treble 12
• NORMAL mode
Select NORMAL mode if you connect a
small sized active center speaker to this
speaker system. Since a small speaker
cannot produce enough bass, the bass
sound of the center channel is output from
the front speakers.
volume 10
Audio component hookups 9
Rear
speaker (L)
Rear
speaker (R)
C
Front
Small
Front
The test tone is output:
Center mode 12, 14
speaker (L) center speaker speaker (R)
/ Front (L) + (R) / Rear
NORMAL mode 12, 14
PHANTOM mode 12, 14
3 CH LOGIC mode 12, 14
WIDE mode 12, 14
Delay time
Time lag between the surround sound output
from front speakers and rear speakers. By
adjusting the delay time of the rear speakers,
you can obtain the feeling of presence. Make
the delay time longer when you have placed
the rear speakers in a small room or close to
your listening position, and make it shorter
when you have placed them in a large room
or apart from your listening position.
Connecting. See Hookups
D, E, F, G
Delay time 11, 14
Rear
speaker (L)
Rear
speaker (R)
Dolby Pro Logic Surround 12,
14
The test tone is output as shown on page 12.
center mode 12, 14
Dolby Surround sound 14
• WIDE mode
Dolby Pro Logic Surround
Select WIDE mode if you connect an active
center speaker equivalent to the two front
speakers. With the WIDE mode, you can
take full advantage of Dolby Surround
sound.
Decoding system of Dolby Surround sound
standardized in TV programs and movies.
Compared with the former Dolby Surround
system, Dolby Pro Logic Surround improves
sound image by using four separate channels:
off-screen audio effects, on-screen dialog,
left-to-right panning, and music. These
channels manipulate the sound to be heard
and enhance the action as it happens on the
screen. To take advantage of Dolby Pro Logic,
you should have at least one pair of rear
speakers and/or one center speaker. You also
need to select the appropriate center mode to
enjoy a full effect.
H, I, J, K, L, M
Hookups
AC power cord 9
audio components 9
speakers 8, 9
TV/VCRs 9
Center speaker
Front
Front
speaker (R)
speaker (L)
N, O
NORMAL mode 12, 14
P, Q
PHANTOM mode 12, 14
Dolby Surround
Rear
speaker (L)
Rear
speaker (R)
Encoding and decoding system of Dolby
Surround sound for consumer use. Dolby
Surround decodes the extra channels on the
Dolby Surround-encoded sound tracks of
movie videos and TV programs and produces
sound effects and echoes that make the action
seem to envelop you.
R
Remote 10, 11, 12
The test tone is output as shown on page 12.
S
• 3 CH LOGIC mode
Select 3 CH LOGIC mode if you don't want
to use the rear speakers to output sound.
The sound of the rear channel is output
from the front speakers to let you
experience some of the surround sound
without using rear speakers.
Speakers
connection 8, 9
placement 7
Speaker volume 11
Surround sound 10, 11
Center speaker
Front
Front
speaker (L)
speaker (R)
T
Test tone 11
3 CH LOGIC mode 12, 14
Troubleshooting 13
TV/VCR hookups 9
U, V
Unpacking 4
The test tone is output:
/ Front (L) / Center / Front (R)
W, X, Y, Z
Watching video programs 10
WIDE mode 12, 14
14
Printed in Malaysia
Sony Corporation
|