4-000-806-11 (1)
US
Instruction Manual
Personal Navigation System
Instruction Manual
NV-U44
©2008 Sony Corporation
Table of Contents
Menu operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Address search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Intersection search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Quick Link search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Favorites search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Map operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Map scrolling mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Using the map tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Adding an interim destination to the current route. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Viewing the turn-by-turn list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Address book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
continue to next page r
3
Editing the address book data on the unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Transferring address book data from your computer to the unit . . . . . . . . . . . . . . . . . . . . . . 53
Transferring address book data from the unit to your computer . . . . . . . . . . . . . . . . . . . . . . 53
4
Basic Operations
Common procedures to operate the system are explained.
General operations can be performed on the touch screen. Gently touch the displayed icons with
your finger.
Note
Do not press the display with excessive force. Do not use any sharp object, such as a pen, etc., to tap on
the display.
Menu operations
The main menu appears when you turn on the unit (except during route guidance, in which case
the map appears).
1
2
MENU
VOICE/
POS.
3
4
5
6
7
1 Press to show the main menu.
2 To check the battery status and current time.
3 Press to show the current position on the map.
4 Touch to show the navigation menu.
5 Touch to show the application menu.
6 Touch to show the setting menu.
7 Touch to return to the previous display.
continue to next page r
5
Other basic menu operations
To
Touch
cancel the setting
“Cancel”
confirm the selection/proceed to the next step “Done” or “OK”
About the battery status indication
The battery status can be checked by the indicator in the main menu.
Indicator
Status
Adapter connected.
Fully charged.
Not fully charged.
Low battery.
Battery is empty. Charge battery immediately.
6
Gesture Command operations
Frequently-used operations can be performed by assigning finger strokes such as a line, etc.
For navigation
In the map display (except in map scrolling mode), draw the command stroke as below.
To
Make
start navigation to your home (page 15)
a circumflex
an “L” shape
start navigation to a destination stored in
“Favorite 1”
“Favorite 2”
a mirror-reversed “L”
a clockwise circle
change map scale to the “Preset Scale”
a counterclockwise circle
continue to next page r
7
For photo playback
In the photo playback display, draw the command stroke as below.
To
Make
start the slideshow
(only when playback controls are shown)
a dot
skip to the previous file
skip to the next file
a horizontal line (right to left)
a horizontal line (left to right)
skip to the previous folder
a vertical line (downwards)
a vertical line (upwards)
skip to the next folder
8
Keyboard operations
The keyboard display appears when you need to enter text.
When entering addresses, you need only enter characters in upper case, as the system
automatically converts them to appropriate characters. You can change the case or enter special
characters/symbols when necessary.
The following types of keyboards are selectable:
• “QWERTY + 123”: QWERTY layout with number keys.*
• “QWERTY”: Large QWERTY layout without number keys.*
• “ABC”: Alphabetical layout without number keys.
* “QWERTY” refers to the top row of letters, reading from the left, of a traditional typewriter style keyboard.
QWERTY layout with number keys:
Entry field
continue to next page r
9
To
Touch
enter an alphabetical character
enter a number
the desired character key
the desired number key*1
enter a special character
“ÀŐŇ” to switch to the special character
keyboard, then the desired character; and
“ABC” to switch back
enter a symbol
“@!?” to switch to the symbol keyboard, then
the desired symbol key; and “ABC” to switch
back
enter a space
“Space”
“Backspace”
“Caps”
delete a character
change the case
proceed to the next step
show the candidate list*2
confirm the entry
“Next”
“Search”
“Done”
*1 When another keyboard type is selected, touch “123” to switch to the numeric keyboard.
*2 The candidate list automatically appears when candidates are narrowed down as you continue inputting
characters.
10
Navigation
Checking the GPS status
About the GPS status indication
The GPS status can be checked by the color of the current position icon.
If the current position is not displayed, press VOICE/POS. to show the icon.
Current position icon
Indication
Status
Signals are insufficient for navigation.
Reception temporarily interrupted (e.g., in a tunnel).
Signals are sufficient for navigation.
Note
Acquisition of GPS signal may take up to 10 minutes, especially for the first time. Make sure that you are in
an open space for faster acquisition.
Tip
If GPS signal reception is poor after turning on the unit, the information bar appears at the top of the
display.
You can also check the GPS status by the message on the information bar.
By touching the information bar, you can jump to the display where you can view detailed GPS status
continue to next page r
11
Route searching
You can search for a route in various ways.
The following route search methods are available.
Address search
Address search allows you to set the destination by entering the address information such as
house number, street name, etc.
Note on the state selection
The system recognizes the state you usually drive in and sets it as default, so that you do not need to enter
the same state name at each address search.
When GPS detects that the current position is not in the default state, the state selection display
automatically appears, allowing you to set the desired state.
Full address search
Follow the procedure below if you know the house number, street name, and the city name of the
destination.
1 In the menu display, touch
, then “Enter Address.”
If the state selection display appears, select the new (current) state or “Change to Different
State.”
When selecting “Change to Different State,” enter the state name, then select the desired state.
The house number input display appears.
2 Enter the house number.
The street name input display appears.
3 Enter the street name.
The list of street candidates appears.
4 Select the desired street in the list.
The city name input display appears.
5 Enter the city name.
The list of city candidates appears.
continue to next page r
13
6 Select the desired city in the list.
If more than one address candidate exists, the list of candidates appears. In this case, select
the desired address.
The address confirmation display appears.
7 Select “Go.”
Route guidance starts.
Street search
If the house number is not known, a search can be made to an approximate point on the street.
1 In the menu display, touch
, then “Enter Address.”
If the state selection display appears, select the new (current) state or “Change to Different
State.”
When selecting “Change to Different State,” enter the state name, then select the desired state.
The house number input display appears.
2 Select “Skip” without entering the house number.
The search method options appear.
3 Select “Representative Point of the Street.”
The street name input display appears.
4 Enter the street name.
The list of street candidates appears.
5 Select the desired street in the list.
If more than one city or address candidate exists, the setting display(s) appears. In this case,
set the city or select the address.
The address confirmation display appears.
6 Select “Go.”
Route guidance starts.
To set the destination in another state
You can select a different state when “State” appears in the name input displays.
Select “State,” enter the state name, then select the desired state.
Tips
• The state can be set by entering its standard 2-letter abbreviation (e.g., NY for New York).
• The list of state/city/street candidates automatically appears without touching “Search” when narrowed
down to 4 candidates.
continue to next page r
14
Home search
If you register your home, you can search for a route there.
1 In the menu display, touch
, then “Take Me Home.”
Route guidance starts.
Tip
If you select “Take Me Home” without having registered a home address, the registration display
automatically appears.
With Gesture Command
In the map display, draw
.
POI search
POI (Points Of Interest) search allows you to set facilities such as restaurants, hotels, gas
stations, etc., as the destination.
The system searches for POIs near the current position.
To search for the POIs in another city
You can specify the city before selecting the POI search method.
In this case, the system searches for POIs in the city center.
1 In the menu display, touch
, then “Find a Place.”
The search method selection display appears.
2 Select “Points of Interest.”
3 Select “Change City.”
4 Enter the city name.
5 Select the desired city in the list.
To switch back to the nearby search, select “Nearby.”
continue to next page r
15
By POI name
You can search for a route to a POI by directly entering its name.
1 In the menu display, touch
, then “Find a Place.”
The search method selection display appears.
2 Select “Points of Interest.”
3 Select “By Name.”
The POI name input display appears.
4 Enter the POI name.
The list of POI candidates appears in order of distance from the current position.
5 Select the desired POI.
The POI confirmation display appears.
6 Select “Go.”
Route guidance starts.
Tip
If there are too many POI candidates in the list after step 4 above, you can narrow down by selecting
category(ies). Select “Category” to show the category list, then select the desired category(ies).
continue to next page r
16
By POI category
You can search for a route to a POI by selecting its category(ies).
1 In the menu display, touch
, then “Find a Place.”
The search method selection display appears.
2 Select “Points of Interest.”
3 Select “Category.”
The list of category candidates appears.
4 Select the desired category.
Select sub category when necessary until the POI candidates are narrowed down.
The list of candidates appears in order of distance from the current position.
5 Select the desired POI.
The POI confirmation display appears.
6 Select “Go.”
Route guidance starts.
Tip
If there are too many POI candidates in the list after step 4 above, you can narrow down by entering the
POI name. Select “Name” to show the POI name input display, then enter the POI name.
Intersection search
The intersection can be set as a destination, if available for the selected street.
1 In the menu display, touch
, then “Find a Place.”
The search method selection display appears.
2 Select “Find Intersection.”
The street name input display appears.
3 Enter the street name.
The list of street candidates appears.
4 Select the desired street in the list.
If more than one city candidate exists, the city name input display appears. In this case, enter
the city name, then select the desired city.
The street name input display appears.
5 Enter the other street name.
The list of street candidates appears.
6 Select the street.
The address confirmation display appears.
7 Select “Go.”
Route guidance starts.
Tip
The intersection search can also be made by selecting “Enter Address” in step 1 above and skipping the
continue to next page r
17
City center search
The city center can be set as a destination.
1 In the menu display, touch
, then “Find a Place.”
The search method selection display appears.
2 Select “Find City.”
The city name input display appears.
3 Enter the city name.
The list of city candidates appears.
4 Select the desired city in the list.
The address confirmation display appears.
5 Select “Go.”
Route guidance starts.
Tip
The city center search can also be made by selecting “Enter Address” in step 1 above and skipping the
Quick Link search
Quick Link allows for quick access to the preset POI name/category.
Frequently-used POI categories (e.g., “Gas Station”) are preset in Quick Links as default, which
can be changed if desired.
1 In the menu display, touch
, then “Find a Place.”
The search method selection display appears.
2 Select the desired Quick Link.
The list of POI candidates appears in order of distance from the current position.
3 Select the desired POI.
The POI confirmation display appears.
4 Select “Go.”
Route guidance starts.
continue to next page r
18
Changing a POI name/category in Quick Links
1 In the menu display, touch
, then “Find a Place.”
2 Select “Quick Link Settings,” then the desired Quick Link.
3 Select the desired setting method.
Select
To set
By Name
the POI name.
Enter the name.
Category
the POI category.
Select category(ies).
Category and By Name
the POI category and name.
Select category(ies) c “By Name,” then
enter the name.
Recent destinations search
The system stores previous destinations, allowing you to select one quickly from the list.
1 In the menu display, touch
, then “My Places.”
The search method selection display appears.
2 Select “Recent Destinations.”
The list of searched destinations appears in reverse chronological order.
3 Select the desired item in the list.
The address/POI confirmation display appears.
4 Select “Go.”
Route guidance starts.
continue to next page r
19
Address book search
You can select the destination saved in the address book.
For details on how to manage the address book, see page 35.
1 In the menu display, touch
, then “My Places.”
The search method selection display appears.
2 Select “Address Book.”
The list of groups appears.
3 Select the desired group.
The list of data in the selected group appears.
4 Select the desired entry in the list.
The address/POI confirmation display appears.
5 Select “Go.”
Route guidance starts.
Favorites search
You can select a destination that is saved in the Favorites.
1 In the menu display, touch
, then “My Places.”
The search method selection display appears.
2 Select “Favorite 1,” “Favorite 2,” “Favorite 3,” or “Favorite 4.”
Route guidance starts.
With Gesture Command
In the map display, draw one of the command strokes:
– Favorite 1:
– Favorite 2:
continue to next page r
20
Option menu in the address/POI confirmation display
The option menu in the address/POI confirmation display provides various useful operations.
When the confirmation display appears after setting a destination, select “Options,” then one of
the following items.
Item
Purpose
Interim Destination*2 (page 32)
Saves the selected point to the address book.
Edits the selected address book entry.
Adds the point as an interim destination in the
current route. The system navigates you to
this point before the current destination.
*1 Appears depending on your selection. “Edit Item” appears when you select “My Places” c “Address
Book.” In other cases, “Save This Location” appears.
*2 Available only during route guidance.
Fine adjusting the destination point
You can jump from the address/POI confirmation display to the map scrolling mode, and fine
adjust the destination point.
1 Select “Map” in the address/POI confirmation display.
The map in the scrolling mode appears.
2 Drag the screen to fine adjust the destination point, then select “Go.”
Route guidance starts.
21
During route guidance:
Straight-ahead driving
F
G
H
F Distance/ETA (Estimated Time of Arrival) to destination
G Distance to next turn
H Next instruction
Approaching an intersection
I
I Next turn instruction
continue to next page r
23
Approaching an intersection (closer)*
J
K
K Bar indication of the distance to next turn
Approaching an intersection (even closer)*
L
L Current position
continue to next page r
24
Map scrolling mode
You can switch to map scrolling mode by touching the map, whether during route guidance or
not.
By placing the desired point into the crosshair, you can view the information on the point or open
the map options.
Operations in map scrolling mode
To
Operation
scroll a map
drag the screen
touch the point
move the desired point to the center of the
screen
pan the map
touch and hold the center of the crosshair
until the beep sounds, then drag it in the
desired direction
exit the map scrolling mode
press VOICE/POS.
(The current position reappears.)
continue to next page r
25
Using the map tools
The map tool bar appears when you touch “Options” on the map display.
1
2
MENU
VOICE/
POS.
3
4
5
6
7
8
1 To show the main menu.
2 To toggle the map orientation (heading up/north up).
3 During route guidance:
To repeat the last voice guidance.
In other cases:
To return to the current position display.
4 To show more map options.
6 To zoom in/out the map.
Touch
7 To adjust the voice guidance volume.
Touch
/
.
/
.
To turn off the sound, touch
.
8 To hide the map tool bar.
* Available only during route guidance.
continue to next page r
26
More map options
More options are available by selecting “More…” in the map tool bar.
Item
Purpose
Navigate to Here*1
Save This Location (page 35)
Quit Navigation*3
Starts route guidance to the point.
Saves the point to the address book.
Edits the address book entry.
Exits the current route guidance.
Routes a detour for a specified distance from
the current position.
Search from Here*1*4
Searches for POIs near the selected point.
*1 Available only for the point selected in map scrolling mode.
*2 Available only for address book entry icons.
*3 Available only during route guidance.
*4 Appears when
is touched.
*5 Available only if more than one destination point exists.
27
Route planning
Creating a new itinerary
The procedure to create a new itinerary is explained below.
1 In the menu display, touch
, then “Route Planning.”
2 Select “Route Planning,” then “Options.”
3 Select “New Route.”
The route planning display appears in which the current position is set as the start point.
4 Select “Add” to add a route point in your itinerary.
The search method selection display appears.
5 Select the desired search method to set the route point.
Select
To set
Enter Address
Home
by address search (page 13)
your home as the route point (page 15)
Find a Place
My Places
search (page 20)
Browse Map
the current position as the route point
Current Position
continue to next page r
28
6 After setting the route point, select “Done.”
The route planning display reappears with the selected point added in the list.
The last setting is listed as the final destination.
Repeat step 4 to 6 to continue adding route points. Up to 10 route points can be set.
7 Select “Calculate Route.”
The route calculation starts.
After the calculation is complete, the route confirmation display appears.
8 Select one of the following items.
Item
Purpose
Go
Starts the route guidance.
Changes the route calculation conditions.
Change Condition
continue to next page r
29
Editing route points
You can edit the selected route points while creating an itinerary.
Select the desired route point in the route planning display, then one of the following items.
Item
Purpose
Change Location
Shows the search method selection display to
set the route point again.
Delete
Deletes the selected point from the itinerary.
Changes the order of route points.
Change Order
Select the point to move c
/
c “Done.”
Tip
You can open the route planning display and modify your itinerary, even after starting route guidance.
continue to next page r
30
Option menu for route planning
The option menu in the route planning/route confirmation display provides various useful
operations.
When the route planning/route confirmation display appears, select “Options,” then one of the
following items.
Item
Purpose
Save Route
Saves the current route.
Select an unregistered line in the list, then
enter the name.
To overwrite a registered route, select a
registered line in the list c “OK.”
Saved Routes*1
Edits the route/starts the route guidance.
Select the route, then one of the following
options.
– “Edit”: Shows the route planning display to
edit the route point.
– “Rename”: Changes the name of the
selected route.
– “Delete”: Deletes the selected route.
– “Start Navigation”: Starts the route
guidance.
Shows/changes the current route profile
settings.
Calculation Condition*1
Sets the route calculation conditions.
New Route*1
Shows the route planning display to create a
new itinerary.
Sort by Distance*1
Sorts the route points in order of distance
from the start point.
Simulation*2
Simulates the current route.
*1 Appears only in the option menu of the route planning display while setting the route point(s).
*2 Appears only in the option menu of the route confirmation display after setting the route points.
continue to next page r
31
Adding an interim destination to the current route
During route guidance, you can add an interim destination.
1 In the menu display, touch
, then select the desired search method to set
the interim destination.
For details on search methods, see “Route searching” on page 13.
You can select the desired search method, except for home search and Favorites search.
2 After setting the interim destination, select “Options” in the address/POI
confirmation display.
3 Select “Interim Destination.”
The route guidance to the interim destination starts.
Skipping to the next destination
If more than one destination point exists during route guidance, you can cancel the current
destination and reroute to skip to the next destination.
1 In the map display, select “Options,” “More...,” then
2 Select “Skip to Next Destination.”
.
The current destination is canceled, and the route guidance to the next destination starts.
Blocking the route
During route guidance, you can detour for a specified distance from the current position. For
example, if traffic congestion occurs ahead of the route, you can reroute to avoid this area.
1 In the map display, select “Options,” “More...,” then
.
2 Select “Block Route.”
The distance setting display appears.
3 Select the desired distance, then “Detour.”
Recalculation starts.
32
Viewing the entire route
During route guidance, you can view the entire route to the destination.
1 In the map display, select “Options,” then “Turns.”
2 Select “Confirm Route.”
The entire route appears.
To change the route calculation conditions
1 Select “Change Condition,” then the desired option.
Route guidance starts.
Viewing a map of the vicinity of the destination
During route guidance, you can view a map of the vicinity of the current destination.
1 In the map display, select “Options,” then “Turns.”
2 Select “Show Destination.”
A map of the vicinity of the current destination appears.
34
Destination management
Destinations on “Recent Destinations,” “Address Book,” and “Favorites” can be managed.
Recent destinations
You can delete the history of “Recent Destinations.”
1 In the menu display, touch
2 Select “Delete.”
, “My Places,” then “Recent Destinations.”
3 Select the item to delete.
To select all items, select “All.”
To unselect all items, select “Clear.”
4 Select “Done,” then “OK.”
The selected item(s) is deleted.
Address book
You can register the destinations or points on the map to the address book.
From the navigation menu
1 In the menu display, touch
, then select the desired search method.
For details on search methods, see “Route searching” on page 13.
You can select the desired search method, except for home search, address book search, and
Favorites search.
2 After setting the destination, select “Options” in the address/POI confirmation
display.
3 Select “Save This Location.”
The registration display appears.
continue to next page r
35
4 Set the following items.
Item
Purpose
Name
Group
Enters the name.
Selects the group to categorize.
To create a new group, select “New Group,”
then enter the group name.
Phone
Icon
Enters the phone number.
Selects the icon to show on the map.
To select from the facility icon list, select
“Facilities Icons” c category(ies) c icon.
Sound
Configures the sound setting.
– “Sound Function”: Sets to “ON” to have
notification sound upon approach.
– “Sound Source”: Selects the sound source.
– “Distance of Starting to Play Back”:
Selects the distance at which the sound
will be output.
5 Select “Done.”
The destination is added to the address book and indicated by the selected icon on the map.
From the map option menu
1 In the map display, touch the map to switch to the map scrolling mode, then
select the desired point.
2 Select “Options,” then “More...”
Follow the procedure from step 3 above to add the selected point to the address book.
Tip
Favorites
You can register destinations to “Favorite 1,” “Favorite 2,” “Favorite 3,” and “Favorite 4”
separately.
1 In the menu display, touch
2 Select “Favorites.”
, then “General.”
3 Select “Favorite 1,” “Favorite 2,” “Favorite 3,” or “Favorite 4.”
4 Select the desired search method.
For details on search methods, see “Route searching” on page 13.
You can select the desired search method, except for Favorites search.
5 After setting the destination, select “Done” in the address/POI confirmation
display.
The destination is stored in the selected Favorite.
To change the registration in Favorites
Follow the procedure above and overwrite a registered Favorite.
36
Photo Playback
You can view photo files stored on a “Memory Stick Duo” inserted in the unit.
Insert a “Memory Stick Duo” containing photo files shot by a Sony digital still camera in the
unit.
Supported photo file type
• File format
JPEG
• File extension
.JPG
• Number of pixels
Max. 12 mega pixels
Viewing photos
1 In the menu display, touch
The list of folders/files appears.
To move to the upper level, touch
, then “Photo.”
.
To list files as thumbnails, select “Thumbnail.”
2 Select the desired folder/file.
If you select a folder, then select the desired file.
The photo playback display appears with the selected photo file.
continue to next page r
37
Photo playback controls
Touch the display if the photo playback controls are not shown.
File name/shooting date and time
1
2
3
4
5
6
7
1 To exit the photo browser.
2 To select a file from the list.
3 To skip to the previous file.
4 To start the slideshow.
5 To skip to the next file.
6 To open the option menu for photo playback.
7 To hide the playback controls.
With Gesture Command
In the photo playback display, draw one of the command strokes:
– Start the slideshow (only when playback controls are shown): z
– Skip to the previous file:
– Skip to the next file:
– Skip to the previous folder:
– Skip to the next folder:
Option menu for photo playback
The following options for photo playback are available.
Select “Opt.” in the tool bar, then one of the following items.
Item
Purpose
Clockwise
Rotates the current photo clockwise in 90
degree steps.
Counterclockwise
Rotates the current photo counterclockwise in
90 degree steps.
38
Photo settings
The following photo settings are configurable.
In the photo file list, select “Settings” c the desired item c the desired option.
Item
Purpose
Playing Interval
Repeat
Sets the slideshow interval.
Repeats the slideshow.
Slideshow Range
Plays slideshow of all photo files in a
“Memory Stick Duo” or the currently selected
folder.
File Order
Sorts photo files by shooting date or name.
39
Settings
The setting menu includes the following categories.
• “Map” (page 44)
• “Route Profile” (page 45)
Route planning settings
The following route planning settings are configurable.
In the menu display, touch
c “Route Planning” c the desired item c the desired option.
Item
Purpose
Route Planning (page 28)
Opens the route planning display to create an
itinerary.
Simulation
Simulates the last route.
40
Address book settings
The following address book settings are configurable.
In the menu display, touch
c “Address Book” c the desired item c the desired option.
Item
Purpose
Edit Item
Edits the address book entry.
Select the group, then one of the following
items.
– Entry in the list: Opens the display where
you can delete an entry, or change the name/
group/phone/icon/sound setting.
– “Move”: Categorizes entry(ies) to another
group. Select the entry(ies) to move c
“Move To” c the new group c “OK.”
– “Delete”: Deletes an entry(ies). Select an
entry(ies) to delete c “Done” c “OK.”
Edit Groups
Edits the group setting.
– “New Group”: Creates a new group.
– “Rearrange Group Order”: Changes the
order of groups. Select the group c
“Done.”
/
c
– “Edit Group Name”: Changes the group
name.
– “Delete Group”: Deletes the group and all
its entries.
Make Backup
Backs up the address book data on a
“Memory Stick Duo.”
Restore Address Book
Import Items
Restores the address book data from a
“Memory Stick Duo.”
Imports the address book entry(ies) from a
“Memory Stick Duo.”
Select the file in the “Memory Stick Duo” c
all entries or individual entry c “Done” c
“OK” c “OK.”
Export Items
Exports the address book entry(ies) to a
“Memory Stick Duo.”
Select the group c entry(ies) c “Done” c
“Done” c “Done,” select/create a file, then
select c “OK” c “OK.”
41
General settings
The following settings related to the system are configurable.
In the menu display, touch
c “General” c the desired item c the desired option.
Item
Purpose
Volume (Operation Sound)
Presets the volume level for touch screen
operation sound: “Level 3,” “Level 2,” “Level
1,” “OFF.”
Units
Selects the distance unit: “Kilometers,”
“Miles.”
Time Format
Selects the clock indication: “12hr (AM /
PM),” “24hr.”
Time Zone
Select Language
Display
Sets the time zone automatically or manually.
Selects the language for on-screen display.
Adjusts the display settings.
– “Brightness, Day / Night Mode”: Switches
the display brightness automatically or sets
the brightness for day time/night time use:
“Automatic,” “Day,” “Night.” The
brightness level for day time and night time
use can be adjusted manually.
– “Touchscreen Calibration”: Performs the
touch screen calibration when the touch
function is off the mark. Touch the targets in
sequence.
Input Home Address
Registers your home address.
– “Enter Address”: Sets from the navigation
menu. For details on how to set the address,
– “Map”: Selects on the map. For details on
how to select the point on the map, see
Start the Configuration Wizard
Daylight Saving Time
Configures the basic settings by following the
wizard (i.e., to perform the Startup
Configuration Wizard again).
Sets daylight saving time automatically by
GPS or manually.
– “Automatic”: Updates automatically by
GPS.
– “Manual (+1h)”/“Manual (+30min)”: Sets
manually.
– “OFF”: Standard time.
continue to next page r
42
Item
Purpose
GUI Day / Night Mode
Power Saving (Display OFF)
Selects the color theme of menu displays.
Turns off the display automatically after
several minutes of inactivity: “ON,” “OFF.”
Selects the keyboard type: “QWERTY +
123,” “QWERTY,” “ABC.”
Password Lock
Locks the unit by setting a 4-digit numerical
password to prevent unauthorized access:
“ON,” “OFF.” Once activated, you will need
to enter the password when you turn on the
unit.
To activate, select “ON,” enter the password,
reenter the password to confirm, then select
“OK.”
To deactivate, select “OFF,” enter the
password, then select “OK.”
Change Password
Changes the password for locking the unit.
Enter the current password, enter the new
password, then reenter the new password.
Reset Factory Default
Product Information
Resets settings to default.
Views the ID number and status (cradle
connection, etc.) of the unit.
Firmware Version
Views the detailed GPS status information.
Views the firmware version.
Memory Stick Information
Views the information of the currently
inserted “Memory Stick Duo,” such as used/
free space; formats the “Memory Stick Duo.”
To format, select “Format” c “OK”
repeatedly.
Demonstration Mode
– “Automatic Demonstration”: Sets to start
the demonstration automatically after
several minutes of inactivity: “ON,” “OFF.”
– “Start Demonstration”: Starts the
demonstration.
Registers destinations in Favorites.
Track Log
– “Store Track Log”: Logs your position at
regular intervals while driving, and stores
the data on a “Memory Stick Duo” inserted
in the unit for later use on your computer,
etc.
– “Delete All Track Logs”: Deletes all track
logs stored on a “Memory Stick Duo.”
43
Map settings
The following map display settings are configurable.
In the menu display, touch
c “Map” c the desired item c the desired option.
Item
Purpose
2D / 3D Map View
Selects the default map view.
– “2D”: Overhead view.
– “3D” (level 1): Aerial view (high angle).
– “3D” (level 2): Aerial view (medium angle).
– “3D” (level 3): Aerial view (low angle).
Map Orientation
Map Color
Selects the default orientation of 2D map.
– “In Direction of Travel”: Heading up.
– “Always North”: North up.
Selects the map color schemes for day time
use and night time use.
Automatic Map Color Change
Switches the map color scheme automatically.
Presets the map scale level for clockwise and
counterclockwise circles of Gesture
Command.
Landmark Icon
Shows landmark icons on the map.
The settings can be configured separately for
each facility.
Driving Trail
Shows driving trail on the map: “ON,” “OFF.”
Deletes driving trail.
Delete Driving Trail
Address Book Icon
Shows the address book entry icons on the
map: “ON,” “OFF.”
Road Width
Selects the width of the road shown on the
map: “Wide,” “Standard.”
Font Size
Selects the size of the fonts shown on the
map: “Large,” “Medium,” “Small.”
Icon Size
Selects the size of the icons shown on the
map: “Large,” “Medium,” “Small.”
Zoom While Scrolling
Compass and Speedometer
Zooms out the map/fixes the scale when
scrolling: “ON,” “OFF.”
Shows the current speed and direction on the
map when no route guidance is in progress:
“ON,” “OFF.”
Map Version
Views the version of the current map.
44
Route profile settings
The following route profile settings are configurable.
In the menu display, touch
c “Route Profile” c the desired item c the desired option.
Item
Purpose
Ferries
Allows the use of ferries/avoids them unless
no alternative is available: “Allow,” “Avoid.”
Carpool Lanes
Allows the use of carpool lanes/avoids them
unless no alternative is available: “Allow,”
“Avoid.”
Driving Route History
Calculation Condition
Uses the driving route history when
calculating the route: “Use,” “Not Use.”
Sets the route calculation conditions.
45
Guidance settings
The following route guidance settings are configurable.
In the menu display, touch
c “Guide” c the desired item c the desired option.
Item
Purpose
Volume (Guide)
Presets the volume level for voice guidance:
“Level 3,” “Level 2,” “Level 1,” “OFF.”
Voice Attention (Merge)
Automatic Zoom
Intersection Zoom
Select Voice
Activates the audio warning on merge: “ON,”
“OFF.”
Zooms out the map automatically when
driving on the highway: “ON,” “OFF.”
Shows the magnified view of an intersection:
“ON,” “OFF.”
Selects the guidance voice type.
For details on how to import guidance voice
data from your computer, see “Guidance
To select the desired item, select the item c
“Done.”
To delete the item, select the item to delete c
“Delete” c “OK.”
46
Using the PC Application Software
You can install the PC application software to your computer. Using the software, you can
manage various data to use on the unit.
System requirements
Computer
• IBM PC/AT compatible machines
• USB port
OS
• Microsoft Windows 2000 Professional with Service Pack 4 (or later)
• Microsoft Windows XP Home Edition/Professional with Service Pack 3 (or later)
• Microsoft Windows XP Media Center Edition/Media Center Edition 2004/Media Center
Edition 2005
• Microsoft Windows Vista Home Basic/Home Premium/Business/Ultimate with Service Pack 1
(or later)
Monitor
High color (16-bit color) or more, 800 × 600 dots or more
Other
Internet connection for data download and support
Notes
• The following system environments are not supported.
– Non IBM PC type computers, such as Macintosh, etc.
– Homemade computers
– OS upgraded computers
– Multi-monitor environment
– Multi-boot environment
• Depending on the computer condition, operation may not be possible even with the recommended
environment.
47
Installing the software
2 Enter your model number, then click “Continue.”
3 Select “Drivers,” then “nav-u tool” to download the software.
4 Follow the instructions at the website and complete the installation.
Connecting the unit to your computer
1 Turn on the unit and your computer.
2 Connect the unit to your computer with the USB cable.
Note
While using the software or transferring data, do not:
– disconnect the USB cable.
– turn off or reset the unit.
– shut down the computer, enter computer standby mode, or restart the computer.
Disconnecting
After using the software or completing the transfer, exit the software, then disconnect the USB
cable.
48
Guidance voice data management
You can transfer guidance voice data from your computer to the unit, using the software.
Before starting, connect the unit to your computer and start the software.
You can also transfer data to the “Memory Stick Duo” inserted in the unit.
1 Select “Guidance Voice Manager.”
If the guidance voice data on your computer does not appear, select “Browse,” then specify
the data location on your computer.
2 Select the drive corresponding to the unit/“Memory Stick Duo.”
3 In the list, check the box(es) of the guidance voice data to transfer, then select
.
Transfer starts.
4 Select “OK.”
The guidance voice data is transferred to the unit/“Memory Stick Duo.”
Note
In step 3 above, a notification appears if free space is insufficient on the unit/“Memory Stick Duo.” Delete
unnecessary data by selecting “OK” c “Show” in “Target” c the data to delete c “Delete” c “OK” c “OK.”
50
Map data management
You can transfer and replace the map data on the unit, using the software (e.g., to restore map
data if necessary).
Before starting, connect the unit to your computer and start the software.
1 Select “Map Manager.”
If the map data does not appear, select “Browse,” then specify the data location.
2 In the list, select the map to transfer, then
.
3 Select “OK.”
Transfer starts.
4 Select “OK.”
The map on the unit is replaced.
51
Address book data management
Address book data on the unit or your computer can be managed, using the software. You can
transfer or import the address book data on the unit or your computer.
Editing the address book data on your computer
You can edit the address book data on your computer, using the software.
1 Select “Address Book Manager.”
If the data does not appear in the list, select “Browse,” then specify the data location.
2 Select
.
3 Select the group/entry to edit, then the desired edit menu.
Select
Add
To
add a new group/entry.
edit the selected group/entry.
Edit
4 Select “OK” after editing is complete.
5 Select “Save item(s) to PC.”
The address book data on the computer is updated.
To delete the group/entry
In step 3 above, select the group/entry to delete c “Delete” c “OK.”
Editing the address book data on the unit
You can edit the address book data on the unit, using the software.
Before starting, connect the unit to your computer and start the software.
1 Select “Address Book Manager.”
2 Select
.
the address book data on the unit, then select “Apply to the Unit.”
continue to next page r
52
Transferring address book data from your computer to the unit
You can transfer address book data from your computer to the unit, using the software.
Before starting, connect the unit to your computer and start the software.
1 Select “Address Book Manager.”
2 Select
.
If the data does not appear in the list, select “Browse,” then specify the data location.
3 Check the box(es) of the group(s)/entry(ies) on your computer.
4 Select “Transfer including group name.” or “Transfer only item(s).”
5 Select “Transfer.”
Transfer starts.
6 Select “Apply to the Unit,” then “OK.”
The address book data is transferred to the unit.
Note
In step 5 above, a notification appears if free space is insufficient on the unit. Delete unnecessary address
Transferring address book data from the unit to your computer
You can transfer address book data from the unit to your computer, using the software.
Before starting, connect the unit to your computer and start the software.
1 Select “Address Book Manager.”
2 Select
.
3 Check the box(es) of the group(s)/entry(ies) on the unit.
4 Select “Save to PC.”
5 Select “Save.”
Transfer starts.
6 Select “OK.”
The address book data is transferred to your computer.
Note
In step 4 above, a notification appears if free space is insufficient on your computer. Delete unnecessary
data from your computer.
53
|
