TABLE OF CONTENTS
SAFETY INSTRUCTIONS .................................................................. 2
INTRODUCTION............................................................................. 4
Package Contents ..................................................................... 4
Installing or Removing the Tilt/Swivel Base ............................ 5
Specifications ........................................................................... 6
Recommended Use of the Monitor .......................................... 7
CONTROLS AND ADJUSTMENTS ................................................... 8
Front User Controls. ................................................................ 8
"General" ................................................................................. 9
"Picture" .................................................................................. 9
"Geometry".............................................................................. 9
"Color"..................................................................................... 9
"Advance" .............................................................................. 10
"Porperty" .............................................................................. 10
"Signal" .................................................................................. 11
Contrast ................................................................................. 11
Energy Declaration ................................................................ 11
TECHNICAL INFORMATION......................................................... 12
Compatibility ......................................................................... 12
Pin Assignment............................................................... 12
Preset Timing Chart ........................................................ 13
TROUBLESHOOTING.................................................................... 14
DIMENSION .................................................................................. 15
PLUG & PLAY: DISPLAY DATA CHANNEL (DDC) ........................ 16
MANUFACTURER'S LIMITED WARRANTY. .................................. 16
1
¨ ¨ ¨
SAFETY INSTRUCTIONS
Usually when this product is sold a suitable power cord is provided by
the manufacturer. However, this product is sometimes resold or
transported to another area with a different power system and safety
requirements. Please pay attention to the selection of a suitable power
cord.
The plug on the power cord is intended to serve as the disconnect
device, the socket-outlet shall be installed near the equipment and
shall be easily accessible.
9. Do not allow anything to rest on the power cord. Do not locate this
product where persons can walk on the cord.
10. Never push objects of any kind into this product through cabinet slots
as they may touch dangerous voltage points or short out parts that
could result in the risk of fire or electric shock. Never spill liquid of
any kind on the product.
11. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points, or other risks.
Refer all servicing to service personnel.
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If when the operating instructions are followed, the product does
not operate normally, adjust only those controls that are covered
by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work
by a qualified technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating
a need for service.
3
¨ ¨ ¨
INTRODUCTION
Introduction
The monitor is a multiple frequency high-resolution color monitor for IBM
compatible PC's or Macintosh and workstation systems. The monitor is
equipped with microprocessor based intelligence and multiple frequency
scanning capability, allowing it to provide maximum compatibility for various
system platforms.
The monitor uses the latest screen technology including a 0.24mm AG
Trinitron® CRT to display crisp text and vivid color graphics. The full-function
digital control and On-Screen Display (OSD) system provides easy adjustment
of image geometry and color settings for different display modes with the
precision of a fixed frequency monitor.
The monitor also has full ergonomic features. In addition to the friendly controls
and user comfort features, the emission level of the electric and magnetic field
is kept low to meet the Swedish MPR II and TCO standards.
The monitor is also equipped with energy saving functions; it is compatible
with the VESA power saving standards.
Package Contents
The following lists all of the items included in the monitor package box. Please
save the original box and packing materials for future transportation or shipment
of the monitor.
Front View
User's Manual
Rear View
Power Cord
4
¨ ¨ ¨
INTRODUCTION
Installing or Removing the Tilt/Swivel Base
1.Turn off the system and all attached peripherals.
2.Carefully set the monitor upside down.
Remove the Tilt/Swivel Base:
1.Squeeze and hold the latches.
2.Pull the tilt/swivel base to the rear of the monitor and lift to remove the
base.
Installing the Tilt/Swivel Base:
1.Align the base with the slots on the bottom of the monitor and insert the tilt/
swivel base into the slots.
2.Push the tilt/swivel base firmly toward the front of the monitor until the
latches click into the locked position.
Insta ll
Re m o ve
5
¨ ¨ ¨
INTRODUCTION
Specifications
Color Picture Tube
43.1 cm / 17" (16" viewable screen size) diagonal
measurement, 90 degree deflection, Trinitron® CRT,
anti-glare, anti-reflection, anti-static
AG Pitch
0.24 mm, (at center)
Input Signal
Video: 0.7 Vp-p/75 ohm, analog positive
Sync: Separate Sync.:
Horizontal Sync.: positive/negative
Vertical Sync.: positive/negative
TTL Level
Composite Sync.: TTL Level, positive/negative
Scan Frequency
Horizontal: 30 to 85 kHz automatically
Vertical: 50 to 160 Hz automatically
Max. Resolution
Display Colors
Pixel Rate
1600 x 1200 pixel, non-interlaced
Analog input, unlimited colors
175.5 MHz
Plug & Play
DDC 1 / DDC 2B
Power Supply
Power Consumption
Dimensions
100-120 VAC/200-240 VAC, 50/60 Hz (automatically)
110W max.
418(W) x 430(H) x 447(D) mm
23 kgs(G.W.), 20 kgs(N.W.)
Operating Temperature: 0°C to 35°C
Weight
Environment
Consideration
Humidity
Temperature: –20°C to 60°C
Humidity 10% to 90%
20% to 80%
Storage
Note: Specifications are subject to change without notice.
6
¨ ¨ ¨
INTRODUCTION
Recommended Use of the Monitor
When setting up and using the monitor, pay special attention to the following
for optimum performance:
• Do not use your monitor against a bright background or where sunlight or
other light sources will shine directly on the screen.
• The monitor should be placed just below eye level (10°~15°) for optimum
viewing.
• Set the monitor's brightness to match ambient room light.
• For optimum focus, the contrast control should not be set to the maximum
level unless the input signal level is extremely low. Also, the brightness
control should be set to a point where the overall background area just
begins to disappear.
• Allow adequate ventilation around the monitor so that the heat from the
monitor can be properly dissipated.
• Neither the monitor itself, nor any other heavy objects, should rest on the
power cord. Damage to the power cord can cause fire or an electric shock.
• Keep the monitor away from high-capacity transformers, electrical motors,
or other strong magnetic fields.
• Your monitor should not be used in damp, dusty, or dirty areas.
• Handle your monitor with care when transporting it.
!
CAUTION
ê
• Do not scrape or knock the surface of the CRT with a pen, a
screwdriver and so on.
• Clean the CRT surface with a lint-free, nonabrasive, soft cloth, do
not use a solution or glass cleaner containing corpuscles like
abrasives, alcohols and alkalines.
7
¨ ¨ ¨
CONTROLS AND ADJUSTMENTS
Controls and Adjustments
Once you have installed the monitor with your system, please read the
instructions of this section which give you some guidelines on how to use the
monitor more efficiently. It leads you through the various function of the user
controls and explains how to adjust the monitor to your personal preference.
Front User Controls
1. Power Switch
To turn the monitor on or off.
2. Power LED Indicator
As long as the monitor is powered, this indicator is lit. In normal operation, it
lights green. While in power saving mode, the indicator will turn to amber.
3. Adjust Keys
•To adjust the parameter of the selected function.
•To adjust the contrast level of the screen.
4. Menu Key
To display and select the "General", "Picture", "Geometry", "Color",
"Advance", "Property", "Signal" functions.
Power Saving Note:
This monitor is equipped with a automatic power-saving circuitry design that
will work with any computer which meets the VESA DPMS standard. It also
meets the ENERGY STAR low power state definition.
8
¨ ¨ ¨
CONTROLS AND ADJUSTMENTS
(1) Press " " or " " to open the On-Screen menu function. Seven adjustment
3
4
functions will appear on the On-Screen menu.
Press " " key to scroll down through the selections.
3
A.General
a. Press " " to select Brightness or Contrast.
4
b. Press "+" or "–" to preferred picture.
B. Picture
C. Geometry
D. Color
a. Press " " to select Vertical and Horizontal position,
Vertical and Horizontal size.
b. Press "+" or "–" to preferred picture.
4
a. Press " " to select Side-pin, Balance, Keystone,
4
Parallel and Rotate.
b. Press "+" or "–" to preferred picture.
a. Press " " to select various white color temperature
4
standards.
b. In User item presss "+" to confirm action color
adjustment.
c. Press " " to select Red, Green and Blue.
4
d. Press "+" or "–" increase or decrease density.
9
¨ ¨ ¨
CONTROLS AND ADJUSTMENTS
E. Advance
a. Press " " to select Moire or Degauss.
4
b. Press "+" to proceed.
c. Press "+" or "–" to preferred picture.
Caution:
1. If moire reduction is overdone, picture quality,
i.e. focus and vertical line stability will both be
effected.
2. Proper adjustment is recommended for not
effecting picture perfermance.
F. Property
F-1. Status
F-2. Recall
Press " " to select Status, Recall or Language sub-
manual.
4
The status show the current input signal information
such as Resolution, Horizontal Frequency and Vertical
Frequency.
Confirm the Recall action by pressing the "+" or cancel
the action by pressing the "–".
10
¨ ¨ ¨
CONTROLS AND ADJUSTMENTS
F-3. Language
Press "+" or "–" to select the Language for OSD only.
(2) When OSD is off, "+" or "–" will increase or decrease contrast.
Energy Declaration
This monitor is equipped with a function for saving energy which supports the
VESA Display Power Management Signaling (DPMS) standard. This means that
the monitor must be connected to a computer which also supports the VESA
DPMS standard to fulfill the requirements of the NUTEK specification 803299/
94/96. The time settings for switching to a power saving mode are adjusted
from the system unit by software. From the first indication of inactivity to power
saving position A2 the total time must not be set to more than 70 minutes.
1. VESA Power-Management Proposal
2. Power Consumption (120/230 Vac)
Power
Consumption
VESA DPMS Standard
NUTEK
VESA state
LED indicator
H. sync
Off
V. sync
On
Video
Blank
Blank
Blank
State
Stand-by
Suspend
Off
Normal
operation
On
Green
<110W
Power Saving
Position A1
Suspend
Off
Amber
≤15W
On
Off
Power Saving
Position A2
Amber
≤5W
Off
Off
11
¨ ¨ ¨
TECHNICAL INFORMATION
Compatibility
This color monitor supports multiple operating platforms such as IBM
compatible and Macintosh family computers. This section provides you with
detailed information on the pin assignment of the D-Sub connector and the
preset timing chart of the prevailing video standards.
Pin Assignment
1
6
5
10
15
11
Ma le Mini D-15 C o nne c to r
Signal
15 Pin Mini D-Sub
Red Video
1
Green Video
Blue Video
Horizontal Sync
Vertical Sync
Ground
2
3
13
14
4,5,6,7,8,10,11
No Connection
SDA (DDC)
SCL (DDC)
9
12
15
12
¨ ¨ ¨
Note:This monitor is equipped with a micro-processor which allows the user
to set his own preferred mode(s) beyond those standard mode listed
below.
Preset Timing Chart
8 1 3 8 8
n g E l i s h
HORIZONTAL
VERTICAL
VESA
640x480
at 85 Hz
MAC
832x624
at 75 Hz
VESA
800x600
at 85 Hz
MAC
1152x864
at 75 Hz
VESA
1024x768
at 85 Hz
VESA
1280x1024
at 75 Hz
640x480
at 120 Hz
800x600
at 120 Hz
1024x768
at 100Hz
VGA
Display Format
Hotizontal Dots
Vertical Lines
640
480
720
400
640
480
640
480
832
624
800
600
800
600
1152
864
1024
768
1024
768
1280
1024
H. Frequency(kHz)
H. Sync. Polarity
Aµs (Period)
31.469
43.269
–
63.530
–
49.726
–
53.674
+
75.985
–
67.500
+
68.677
+
80.468
–
79.976
+
–
–
31.778
3.813
1.907
25.422
0.636
23.111
1.556
2.222
17.778
1.555
85.008
–
15.741
1.749
1.731
11.660
0.601
119.868
–
20.110
1.117
3.910
14.524
0.559
74.552
+
18.631
1.138
2.702
14.222
0.569
85.062
+
13.160
1.074
1.951
9.827
0.308
120.039
–
14.815
1.185
2.370
10.667
0.593
75.000
+
14.561
1.016
2.201
10.836
0.508
84.997
+
12.427
1.073
1.945
9.309
0.100
99.836
–
12.504
1.067
1.837
9.481
0.119
75.024
+
*Bµs (Pulse Width)
Cµs (Back Porch)
Dµs (Active Area)
Eµs (Front Porch)
V. Frequency(Hz)
V. Sync. Polarity
Oms (Period)
59.940
–
70.087
+
16.683
14.268
11.763
0.069
0.578
11.093
0.023
8.343
0.094
0.567
7.555
0.127
13.413
0.060
0.784
12.549
0.020
11.756
0.056
0.503
11.179
0.018
8.330
0.039
0.382
7.896
0.013
13.333
0.044
0.474
12.800
0.015
11.765
0.044
0.524
11.183
0.014
10.016
0.037
0.423
9.544
0.012
13.329
0.038
0.475
12.804
0.012
Pms (Pulse Width)
Qms (Back Porch)
Rms (Active Area)
Sms (Front Porch)
0.064
1.049
15.253
0.318
1.112
12.711
0.381
* Bµs (Pulse Width) should be more than 0.5 µs.
To reduce visual tiredness and eye strain, it is recommended to choose the highest refresh modes available.
English
TROUBLESHOOTING
Troubleshooting
Before calling an authorized service center please check that the items below
are properly connected or set.
In case of using a non-standard signal, please check the pin assignments and
the signal timing of your adapter with the specifications outlined in sections
"Pin Assignment Table" and "Preset Timing Chart".
Problem
Items to check
No picture
• Power Switch should be in the ON position and the power cord should be properly connected.
• Check the color of the power LED indicator; if it is orange, then the monitor is in a power
saving mode.
• Check if the horizontal/vertical frequency are out of range.
• Maximize the Brightness and Contrast controls.
"No Signal Input" is displayed on • The video card should be completely seated in its slot.
the screen
• The computer power switch should be in the ON position.
• The signal cable should be completely connected to the video card/computer.
Display image is not centered,
too small, or too large
• Change the Position and Size controls to adjust the image.
Image is scrolling or unstable
• The signal cable should be completely attached to the computer.
• Check the pin assignments and signal timings of the monitor and your video card.
Picture is fuzzy
• Adjust the Contrast and Brightness Controls.
• Push the degauss button once.
CAUTION: A minimum interval of 20 minutes should exist before the degauss button is pressed
a second time when not switching between modes.
Do not hold the button down continuously.
Picture bounces or a wave
pattern is present in the picture
• Relocate electrical devices that may be causing electrical interference.
• See the inside front cover of this manual for FCC information.
Edges of the display image are
curved either inward or outward
• Adjust the Pincushion control.
Color looks blotchy
• Press the Degauss button once.
No Plug & Play functionality
•Check if the host system is Plug & Play compatible.
•Check if the VGA card is DDC 1/DDC 2B compatible.
•Check if Window '95 is installed and the software key for DDC function is enabled).
Our PR705F has built-in Trinitron® CRT. The CRT is sensitive to shocks and
vibrations that may occur during transportation. Following are some adjustment
tips when below mentioned symptoms occur.
Symptom
Tip
Two horizontal lines are visible
on the screen
• This is normal charactristic of Trinitron® CRT.
• These are damper wires which are attached to the aperture grille are
designed to dampen and prevent shock and vibration in the
aperture grill.
Black fine vertical lines are
visible on the screen. Shock
and vibration may cause the
aperture grill to misallign
resulting in a few fine black
• Degaussing the screen.
• Tap lightly (do not hit) the side of the monitor.
If above mentioned remedies do not work, please do the following:
1. Display full white window or wallpaper background over the area
where the black lines appears.
vertical lines across the screen 2. Set Contrast and Brightness to the maximum, wait for a moment until
the problem is corrected. You may try to tap lightly the side of the
monitor to help expedite the alignment.
14
¨ ¨ ¨
DIMENSIONS
unit: mm
15
¨ ¨ ¨
PLUG & PLAY: DISPLAY DATA CHANNEL (DDC)
P
G
L
U
A
L
Y
P
Capability
Notice
: This monitor is equipped with Plug & Play capability(VESA DDC 1/
2B). To utilize this capability, your graphic card and hosting system
have to be Plug & Play compatible as well. When properly
plugged(Plug), the graphic card and hosting system will
automatically (Play)identify, configure, and most importantly,
optimize this monitor's capabilities, providing you with simple and
easy installation and setup.
MANUFACTURER'S LIMITED WARRANTY
The Manufacturer guarantees the Purchaser of this product with one-year free
parts & labor warranty in the unlikely event of product defect caused by material
or workmanship. The product should be returned with original packaging, proof
of purchase, or RMA Number. Furthermore, it is understood and agreed that the
returned product is freightage-prepaid and fully-insured for one-way transit by the
Purchaser within valid warranty period. The defective monitor will be repaired
and/or replaced depending on the defective condition verified by technicians, or
authorized/approved service companies. Due to world-wide distribution of this
product, various customized-warranty of this product may be provided from country
to country, please check the enclosed WARRANTY CARD, or, contact your local
vendors, for different warranty details at your best interest.
16
¨ ¨ ¨
|