TABLE OF CONTENTS
SAFETY INSTRUCTIONS ................................................................. 2
INTRODUCTION ............................................................................ 4
Package Contents .................................................................... 4
Installing or Removing the Tilt/Swivel Base........................... 5
Feature Highlights ................................................................... 5
Maximum Compatibility .................................................. 5
Latest Screen Technology ................................................ 5
Ergonomics concerned ..................................................... 6
Instant Power Saving Solution ......................................... 6
Specifications .......................................................................... 6
Recommended Use of the Monitor ......................................... 7
CONTROLS AND ADJUSTMENTS .................................................. 8
Front User Controls. ................................................................ 8
"Picture" Menu ........................................................................ 9
"Status" Menu........................................................................ 10
"Color" Menu ........................................................................ 11
Contrast and brightness control ............................................ 11
Exit Switch ............................................................................. 11
Energy Declaration ................................................................ 12
TECHNICAL INFORMATION........................................................ 12
Compatibility ......................................................................... 12
Pin Assignment Table .................................................... 12
Preset Timing Chart ....................................................... 13
TROUBLESHOOTING ................................................................... 14
DIMENSION/ABMESSUNGEN/DIMENSION................................ 43
PLUG & PLAY: DISPLAY DATA CHANNEL (DDC) ...................... 44
MANUFACTURER'S LIMITED WARRANTY.................................. 45
1
♦♦♦
SAFETY INSTRUCTIONS
Usually a suitable power cord is provided by the manufacturer, while
this product is sold. However, this product is sometimes, resold or
transported to another area of different power system and safety
requirements, please pay attention to the selection of a suitable power
cord.
The plug on the power cord is intended to serve as the disconnect
device, the scoket-outlet shall be installed near the equipment and
shall be easily accessible.
9. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
10. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electric shock. Never spill liquid of
any kind on the product.
11. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risk.
Refer all servicing to service personnel.
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally, when the operating
instructions are followed, adjust only those controls that are covered
by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the product to normal
operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating
a need for service.
3
♦♦♦
INTRODUCTION
Introduction
The monitor is a multiple frequency high-resolution color monitor for IBM
compatible PC's or Macintosh and workstation systems. The monitor is
equipped with microprocessor based intelligence and multiple frequency
scanning capability, allowing it to provide maximum compatibility for various
system platforms.
The monitor uses the latest screen technology including a 0.25mm Aperture
Grille CRT to display crisp text and vivid color graphics with a max. resolution
up to 1600 x 1200 pixels. Furthermore, it supports VESA 85Hz modes to
provide a flicker free display. The full-function digital control and On-Screen
Display (OSD) system provides easy adjustment of image geometry and
color settings for different display modes with the precision of a fixed
frequency monitor.
The design of the monitor is also ergonomics concerned. In addition to the
friendly controls and user comfort features, the emission level of the elec-
tric and magnetic field is kept low to meet the Swedish MPR II and TCO
standards.
The monitor is also equipped with energy saving functions; it is compatible
with the VESA power saving standards. The lowest power consumption is
Package Contents
less than 8 W.
The following lists all of the items included in the monitor package box.
Please save the original box and packing materials for future transportation
or shipment of the monitor.
Fro nt Vie w
Re a r Vie w
Use r's Ma nua l
Po we r
C o rd
4
♦♦♦
INTRODUCTION
Installing or Removing the Tilt/Swivel Base
1.Turn off the system and all attached peripherals.
2.Carefully set the monitor upside down.
Remove the Tilt/Swivel Base:
1.Squeeze and hold the latches.
2.Pull the tilt/swivel base to the rear of
the monitor and lift to remove the base.
Installing the Tilt/Swivel Base:
1.Align the base with the slots on the bot-
tom of the monitor and insert the tilt/
swivel base into the slots.
Insta ll
Re m o ve
2.Push the tilt/swivel base firmly toward the front of the monitor until the
latches click into the locked position.
Feature Highlights
Maximum Compatibility
• Automatically scans all horizontal frequencies between 30kHz and 95kHz,
and all vertical frequencies between 50 Hz and 160 Hz.
• Supports multiple operating platforms such as IBM compatible PC's or
Macintosh computers (with optional adapter).
• Multiple graphic standards with high refresh rates:
640 x 480/160Hz, 800 x 600/147Hz, 1024 x 768/117Hz, 1280 x 1024/
85Hz, 1600 x 1200/75Hz.
• Supports wide range of graphics standards including VGA, Super VGA,
8514/A, XGA, Mac II 13" (640 x 480), Mac 16" (832 x 624), Mac 21"
(1152 x 870), as well as all VESA standards.
Latest Screen Technology
• 0.25 mm Aperture Grille 17" CRT (43.1 cm) for maximum clarity and
detailed pictures.
• Special anti-reflection, anti-glare and anti-static coating of the screen face
provides better focus, contrast and color performance.
• Cylindrical screen reduces image distortion and glare.
• Full feature digital control and multi-lingual OSD system allows easy
adjustment of geometry and color. Furthermore the monitor provides
even advanced adjustments like trapezoid, parallelogram, side-pin, pin-
balance, convergence and rotation which allow the user to fine-tune the
screen image.
5
♦♦♦
INTRODUCTION
Ergonomics Concerned
• Electric and magnetic field emissions are kept low to meet the Swedish
MPR II and TCO standard.
• Front user controls allow easy access and comfort to adjust the screen
image to your personal preferences.
• Horizontal and vertical full-scan capabilities allow you to use the entire
screen area in most resolutions.
• A tilt/swivel base for horizontal and vertical adjustments always provides
the optimum viewing angle.
Instant Power Saving Solution
• The monitor is compatible with VESA DPMS (Display Power Management
Signalings) standard which provides four power saving modes by detecting
horizontal and vertical sync signals.
• The monitor consumes 65 W to 110 W depending on the screen contents
in normal operation; when a power saving mode is activated, it con-
sumes less than 15 W in Stand-by mode, less than 15 W in Suspend
mode and less than 8 W in Off mode.
Specifications
Color Picture Tube
43.1 cm / 17" (16" viewable screen size) diagonal measurement, 90 degree
deflection, Aperture Grille CRT, anti-glare, anti-reflection, anti-static, medium
short persistence phosphor, dark bulb
Dot Pitch
0.25 mm, Aperture Grille
Input Signal
Video: 0.7 Vp-p/75 ohm, analog positive
Sync:
Separate Sync.: TTL Level
Horizontal Sync.: positive/negative
Vertical Sync.:
positive/negative
Composite Sync.:TTL Level, positive/negative
Scan Frequency
Display Area
Horizontal: 30 to 95 kHz automatically
Vertical: 50 to 160 Hz automatically
Horizontal 300 mm (adjustable)
Vertical 225 mm (adjustable)
Max. Resolution
Display Colors
Video Bandwidth
Misconvergence
Plug & Play
1600 x 1200 pixel, non-interlaced
Analog input, unlimited colors
135 MHz
Center 0.3 mm, Corner 0.4 mm maximum
DDC 1 / DDC 2B
Power Supply
Power Consumption
Dimensions
100-120 VAC/200-240 VAC, 50/60 Hz (automatically)
110W max.
418(W) x 430(H) x 446.5(D) mm
21.3 kgs(G.W.), 18.5kgs(N.W.)
Weight
Environment
Consideration
Operating Temperature:
Humidity
0°C
20%
–20°C
10%
to
to
to
to
35°C
80%
60°C
90%
Storage
Temperature:
Humidity
Note: Specifications are subject to change without notice.
6
♦♦♦
INTRODUCTION
Recommended Use of the Monitor
When setting up and using the monitor, pay special attention to the follow-
ing for optimum performance:
• Do not use your monitor against a bright background or where sunlight
or other light sources will shine directly on the screen.
• The monitor should be placed just below eye level (10°~15°) for
optimum viewing.
• Set the monitor's brightness to match the ambient room light.
• For optimum focus, the contrast control should not be set to the maxi-
mum level unless the input signal level is extremely low. Also, the bright-
ness control should be set to a point where the overall background area
just begins to disappear.
• Allow adequate ventilation around the monitor so that the heat from the
monitor can properly dissipate.
• Neither the monitor itself, nor any other heavy objects, should rest on the
power cord. Damage to the power cord can cause fire or electrical shock.
• Keep the monitor away from high-capacity transformers, electrical motors,
or other strong magnetic fields.
• Your monitor should not be used in damp, dusty, or dirty areas.
• Handle your monitor with care when transporting it.
CAUTION
!
• Do not scrap or knock the surface of CRT with a pen, a
screwdriver and so on.
• Clean the CRT surface with a lint-free, nonabrasive, soft cloth,
and should not use the solution or glass cleaner containing
corpuscles like an abrasive, alcohol and an alkaline solution.
7
♦♦♦
CONTROLS AND ADJUSTMENTS
Controls and Adjustments
Once you have installed the monitor for your system, please read the
instructions of this section which give you some guidelines on how to use
the monitor more efficiently. It leads you through the various function of
the user controls and explains how to adjust the monitor to your personal
preference.
Front User Controls
BNC/D15
▲
▼
–
+
8
7
6
5
4
3
2
1
1. Power Switch
To turn the monitor on or off.
2. Power LED Indicator
As long as the monitor is powered, this indicator is lit. In normal operation,
it lights green. While in power saving mode, the indicator will turn to
amber.
3. Degauss Switch
To manually degauss the monitor.
4. Exit Switch
To exit OSD window.
5. Control Keys
•To adjust the parameter of the selected function.
•To adjust the contrast level or brightness of the screen.
6. Status Key
To display and select the "Mode", "Off time", "Power save", "Recall",
"Language" and "Location" functions.
•"Mode" shows horizontal/vertical frequency and polarity
•"Off time" sets OSD window display time.
•"Power save" enables or disable the power saving function.
•"Recall" recalls the factory settings of the "Picture", "Color" and "Converge"
parameters.
•"Language" selects the OSD menu language.
•"Location" moves the position of the OSD window.
7. Color Key
To display and select the color mode.(four different color modes can be
chosen)
8. Picture Key
To display and select the "Position", "Size", "Pincushion", "Geometry",
"Rotation" and "Others" functions.
Power Saving Note:
This monitor is equipped with a automatic power-saving circuitry design that
will work with any computer which meets the VESA DPMS standard. It meets
the ENERGY STAR low power state definition.
8
♦♦♦
CONTROLS AND ADJUSTMENTS
"Picture" Menu
A.Position:
a. Press the "+" or "–"key to reposition the display to
the right or left.
Picture
Position
Size
Pincushion
Geometry
b. Press the "▲" key to move the entire picture upwards
and "▼" to move it downwards.
Rotation
Others
B. Size:
Picture
Position
a. Press the "+" or "–" key to enlarge or reduce the
horizontal width.
Size
Pincushion
Geometry
b. Press the "▲" key to enlarge the vertical size or "▼"
to reduce it.
Rotation
Others
C. Pincushion:
Picture
Position
a. Press the "▼ " or "▲" key to select "Sidepin" or
"Balance".
b. Press the "+" or "–" key to adjust the picture according
to your preferences.
Size
Pincushion
Sidepin
Geometry
Rotation
Others
79
D. Geometry:
a. Press the "▼" or "▲" key to select "Keystone" and
"Parallel".
Picture
Position
Size
Pincushion
Keystone
Geometry
b. Press the "+" or "–" key to adjust the picture according
to your preferences.
Rotation
Others
90
E. Rotation:
Press the "+" or "–" key to rotate the picture.
Picture
Position
Size
Pincushion
Raster
Geometry
Rotation
Others
50
F. Others:
a. Press the "▼ " or "▲" key to select the Moire or
Convergence.
b. Press the "+" key to proceed.
Picture
Position
Size
Moire
Converg
Pincushion
Geometry
Rotation
Others
: Proceed
c. Press the "+" or "–" key for prefered adjustment.
d. Press the "▼ " or "▲ " key to select the H./V.
Convergence.
Moire
50
e. Press the "+" or "–" key for prefered adjustment.
Caution:
1. If moire reduction is overdone, picture quality, for
example, focus and vertical line stability will be
effected sametimes.
R
B
R
B
46
2. Proper adjustment is recommanded for not effecting
picture perfermance.
9
♦♦♦
CONTROLS AND ADJUSTMENTS
"Status" Menu
A. Mode:
To display timing information for the resolution,
frequency and polarity of the current mode.
Status
1280 x1024
Mode
Off time
Power save H: 63.8 KHz
Recall
V: 59.8
Hz
Language
Location
H. SYNC:
V. SYNC:
+
+
B. Off time:
Press the "+" or "–" key to specify an Off time between
5 and 255 seconds.
tatus
Mode
OSD
After
OFF
EC
Off time
Power save
Recall
8
Language
Location
C. Power save:
Press the "+" key to enable or the "–" key to disable
the power saving function.
Status
VESA DPMS
Mode
Off time
Power save
Recall
: ON
: OFF
Language
Location
D. Recall:
a. Press the "▼" or "▲" key to select "Picture", "Color"
or "Converge".
Status
Mode
Off time
Picture
Color
Power save
Converge
Recall
b. Confirm the Recall action and proceed by pressing
the "+" key or cancel the action by pressing the "–
" key.
Language
Location
:Proceed
Status
Mode
Confirm
Off time
Power save
:YES
:NO
Recall
Language
Location
E. Language:
Press the "▼ " or "▲" key to select between English,
German, French, Spanish or Italian language for the
OSD menu.
Status
Mode
Off time
English
Power save
Recall
Deutsch
ça
Fran is
ño
Espa
l
Language
Location
Italiano
F. Location:
a. Press the "+" key to shift the OSD window to the
right or the "–" key to shift it to the left.
b. Press the "▲" key to move the OSD window
upwards or "▼" to move it downwards.
Status
Mode
OSD
Off time
Power save
Recall
Language
Location
10
♦♦♦
CONTROLS AND ADJUSTMENTS
"Color" Menu
Color
a. By pressing the "Color" key you can select between
mode 1, 2, 3 or 4 to store your user defined color
settings.
Mode 1
Mode 2
Mode 3
Mode 4
62
68
62
°K
9300
b. Press the "▼" or "▲" key to select the R/G/B gain,
then press the "+" key to increase or press the "–" key
to decrease the respective color intensity.
Mo d e 1
Color
Mode 1
52
51
61
Mode 2
Mode 3
Mode 4
°K
7500
Mo d e 2
Color
Mode 1
50
50
50
Mode 2
Mode 3
Mode 4
°K
6500
Mo d e 3
Color
Mode 1
Mode 2
Mode 3
Mode 4
58
47
23
°K
5000
Mo d e 4
Contrast and Brightness Control
When the OSD menu is switched off, proceed as follows
to adjust the contrast or brightness:
a. Press the "+" or "–" key to increase or decrease the
contrast level of the screen.
:50
b. Press the "▲" or "▼" key to increase or decrease the
brightness level.
:100
Exit Switch
You can turn off the OSD window by pressing this key.
11
♦♦♦
CONTROLS AND ADJUSTMENTS
Energy Declaration
This monitor is equipped with a function for saving energy which supports
the VESA Display Power Management Signaling (DPMS) standard. This means
that the monitor must be connected to a computer which also supports the
VESA DPMS standard to fulfill the requirements of the NUTEK specification
803299/94/96. The time settings for switching to a power saving mode are
adjusted from the system unit by software. From the first indication of inac-
tivity to power saving position A2 the total time must not be set to more than
70 minutes.
2. Power Consumption (120/230 Vac)
1. VESA Power-Management Proposal
Power
Consumption
VESA DPMS Standard
NUTEK
VESA state
On
LED indicator
Green
H. sync
Off
V. sync
On
Video
Blank
Blank
Blank
State
Stand-by
Suspend
Off
Normal
operation
<110W
Power Saving
Position A1
Suspend
Off
Amber
<15W
<8W
On
Off
Power Saving
Position A2
Amber
Off
Off
According to TCO guidelines, the optimum TCO readings are measured when
brightness and contrast are adjusted to their center position.
TECHNICAL INFORMATION
Compatibility
This color monitor supports multiple operating platforms such as IBM
compatible and Macintosh family computers. This section provides you with
detailed information on pin assignment of the D-Sub connector and the
preset timing chart of the prevailing video standards.
Pin Assignment
1
6
5
10
15
11
Ma le Mini D-15 C o nne c to r
15 Pin Mini D-Sub
Signal
Red Video
1
Green Video
Blue Video
Horizontal Sync
Vertical Sync
Ground
2
3
13
14
4,5,6,7,8,10,11
No Connection
SDA (DDC)
SCL (DDC)
9
12
15
12
♦♦♦
Note:This monitor is equipped with a micro-processor which allows the
user to set his own preferred mode(s) beyond those standard mode
listed below.
Preset Timing Chart
8 1 3 8 8
n g E s h
HO RIZO NTAL
VERTICAL
VESA
640x480
at 85 Hz
VESA
800x600
at 85 Hz
MAC
1152x864
at 75 Hz
VESA
1024x768
at 85 Hz
VESA
VESA
640x480
at 120 Hz
800x600
at 120 Hz
1024x768
at 100Hz
VGA
832x624
at 75 Hz
1280x1024 1280x1024
Display Format
at 75 Hz
at 85 Hz
Hotizontal Dots
Vertical Lines
640
480
720
400
640
480
640
480
832
624
800
600
800
600
1152
864
1024
768
1024
768
1280
1280
1024
1024
H. Frequency(kHz)
H. Sync. Polarity
31.469
43.269
–
63.530
–
49.726
–
53.674
+
75.985
–
67.500
+
68.677
+
80.468
–
79.976
+
91.146
+
–
–
µ
s
(Period)
A
31.778
3.813
1.907
25.422
0.636
23.111
1.556
2.222
17.778
1.555
85.008
–
15.741
1.749
1.731
11.660
0.601
119.868
–
20.110
1.117
3.910
14.524
0.559
74.552
+
18.631
1.138
2.702
14.222
0.569
85.062
+
13.160
1.074
1.951
9.827
0.308
120.039
–
14.815
1.185
2.370
10.667
0.593
75.000
+
14.561
1.016
2.201
10.836
0.508
84.997
+
12.427
1.073
1.945
9.309
0.100
99.836
–
12.504
1.067
1.837
9.481
0.119
75.024
+
10.971
1.016
1.422
8.127
0.406
85.024
+
µ s
*B (Pulse Width)
µ
s
(Back Porch)
C
µ
D
s
(Active Area)
µ
s
(Front Porch)
E
V. Frequency(Hz)
V. Sync. Polarity
Oms (Period)
59.940
–
70.087
+
16.683
14.268
11.763
0.069
0.578
11.093
0.023
8.343
0.094
0.567
7.555
0.127
13.413
0.060
0.784
12.549
0.020
11.756
0.056
0.503
11.179
0.018
8.330
0.039
0.382
7.896
0.013
13.333
0.044
0.474
12.800
0.015
11.765
0.044
0.524
11.183
0.014
10.016
0.037
0.423
9.544
0.012
13.329
0.038
0.475
12.804
0.012
11.761
0.033
0.483
11.234
0.011
Pms (Pulse Width)
Qms (Back Porch)
Rms (Active Area)
Sms (Front Porch)
0.064
1.049
15.253
0.318
1.112
12.711
0.381
* Bµs (Pulse Width) should be more than 0.5 µs.
To reduce visual tiredness and eye strain, it is recommended to choose the highest refresh modes available.
English
TROUBLESHOOTING
Troubleshooting
Before calling an authorized service center, please check that the items below
are properly connected or set.
In case of using a non-standard signal, please check the pin assignments and
the signal timing of your adapter with the specifications outlined in sections
"Pin Assignment Table" and "Preset Timing Chart" in chapter 4.
Problem
Items to check
•
Power Switch should be in the ON position and the power cord should be properly connected.
•
Check the color of the power LED indicator; if it is orange, then the monitor is in a power
No picture
saving mode.
•
Check if the horizontal/vertical frequency are out of range.
•
Maximize the Brightness and Contrast controls.
•
"No Signal Input" is displayed on The video card should be completely seated in its slot.
•
•
The signal cable should be completely connected to the video card/computer.
the screen
The computer power switch should be in the ON position.
•
Change the Position and Size controls to adjust the image.
Display image is not centered,
too small, or too large
•
The signal cable should be completely attached to the computer.
•
Check the pin assignments and signal timings of the monitor and your video card.
Image is scrolling or unstable
•
Adjust the Contrast and Brightness Controls.
•
Push the degauss button once.
Picture is fuzzy
CAUTION: A minimum interval of 20 minutes should exist before the degauss button is pressed
a second time when not switching between modes.
Do not hold the button down continuously.
•
Relocate electrical devices that may be causing electrical interference.
•
See the inside front cover of this manual for FCC information.
Picture bounces or a wave
pattern is present in the picture
•
Adjust the Pincushion control.
Edges of the display image are
curved either inward or outward
•
Press the Degauss button once.
Color looks blotchy
•C
heck if the host system is Plug & Play compatible.
No Plug & Play functionality
•C
heck if the VGA card is DDC 1/DDC 2B compatible.
•C
heck if Window '95 is installed and the software key for DDC function is enabled.
•C
heck if the manufacturer's original detachable signal cable is being used(D-15 only).
This monitor is build-in Trinitron™ CRT. This CRT is very sensitive to shocks
and vibrations that may occur during transportation. Following are some
adjustment tips when below mentioned symptoms occur.
Symptom
Tip
•
™
One(15") or two(17")
horizontal lines are visible on
the screen
This is normal charactristic of Trinitron CRT.
•
These are damper wires which are attached to the apeture grille and
are designed to dampen and prevent which shock and vibration of the
aperture grill.
•
Black fine vertical lines are
visible on the screen. Shock
and vibration may cause the
aperture grill misalligned,
which results few fine black
Degaussing the screen.
•
Tap lightly (do not hit) the side of the monitor.
If above mentioned remedies do not work, please do the following:
1. Display full white window or wallpaper background over the area
where the black lines appears.
vertical lines across the screen 2. Set Contrast and Brightness to the maximum, wait for a moment until
the problem is corrected. You may try to tap lightly the side of the
monitor to help the expedite of the alignment.
14
♦♦♦
|