I N S T A L L A T I O N I N S T R U C T I O N S
S O NA N C E EL L IP SE L C R I N-C EI L I NG SP EA K E R
PN. 33-2528
INTRODUCTION
RECOMMENDED PLACEMENT CONTINUED
Thank you for purchasing the Sonance Ellipse LCR in-ceiling speaker.
When properly installed, this product will provide you with years of
entertainment pleasure.
Proper placement of the Ellipse LCR is critical for maximum
performance. Try to apply as many of the following recommendations
in your installation.
To obtain the full potential of your new speakers, please read all
instructions before starting the installation. If you do not have the
necessary skills to install the speakers yourself, contact your
authorized Sonance dealer for installation options.
The speakers should be located from eight to eighteen feet from the
listener. The minimum recommended spacing from speaker to listening
position would be approximately 6 feet in a room with eight foot
ceilings. The height and size of the television will largely determine this
distance. Keep in mind that if the television is placed at eye level and
the speakers are installed less than six feet in front of the listening
position the picture and sound could seem very disconnected.
If possible the speakers should be located a minimum of three to four
feet from the front wall this is the wall the television is on.
PARTS LIST
Each Ellipse speaker package includes the following items:
(1) Sonance Ellipse LCR speaker
The left and right speakers should be separated approximately eight to
twelve feet apart with the center speaker placed as close to the middle
as possible. The Sonic Eye on all three speakers should be pivoted
toward the listening position.
(1) Paintable grille
(1) Plastic paint plug to protect speaker during painting
(1) Mounting cutout template ( in packaging )
8 to 18 feet
OPTIONAL ACCESSORIES
FlexBracket - part number 91922
Plastic template to reserve a hole in new construction.
Designed to be used with the Flexbar mountinTgM system.
Acoustical Enclosure - part number 91921
A 1/2" medium density fiberboard enclosure designed
specifically for the Ellipse LCR speaker.
TV
Sonafill in-ceiling - part number 91928
Sonafill is a retrofitable acoustical treatment for that virtually
eliminates the noise produced by resonating drywall and
dramatically improves mid-bass sound quality
RECOMMENDED PLACEMENT
The design of many homes today leaves little space for box or in-wall
LCR speakers. The use of in-ceiling LCR speakers has become quite
common in the last few years. Most of these installations have used
speakers not well suited for this purpose. The Ellipse LCR was
specifically designed to solve this problem.
3 to 4 feet
8 to 18 feet
The most important consideration when using in-ceiling LCR speakers
is maintaining good cohesion between picture and sound. As a general
rule you should try to install the speakers no more than 4 to 6 feet
away from the top of the television. In a room with 8 foot ceilings and
using a rear projection or large tube television this should be very
easy.
TV
Using the following recommendations will insure your installation
achieves maximum performance from the speakers.
Left Center Right Speaker Placement
1
INSTALLING THE SPEAKERS
Step 1
Remove the paint plug from the
speaker. Attach the wire from your
amplifier to the terminals on the back of
the speaker. Double check the polarity
of the speaker wires, amplifier + to
speaker + and amplifier - to speaker -.
Proper polarity is critical in home theater
installations.
PAINTING THE SPEAKERS AND GRILLES
Speakers and grilles can be painted before installation, which will
eliminate the "paint scar" if the speaker needs to be removed for
service. Speakers may also be painted after installation, but before the
grilles are attached. All speakers come from the factory fitted with a
plastic "paint plug." Use the paint plug to protect the drivers while the
flange is being painted with the ceiling.
Step 2
To install the Ellipse LCR, insert one side
of the Flexbar clamps through the hole
in the drywall. Once the feet are
through the hole, insert the other side
of the Flexbars into the cutout.
Sonance suggests always painting the grilles separate from the
speaker. The grilles may be lightly sprayed with thin paint (5 parts
thinning agent to 1 part paint), but be careful not to plug the holes.
Too much paint will adversely affect the sound of the speaker.
Once the grilles and flange are painted and dry, remove the paint plug
from the flange and install the grilles.
Note: The maximum clamp thickness is
1-1/4" (32mm)
ADJUSTING YOUR SPEAKERS
The Sonic Eye
The unique sealed pivoting enclosure can direct sound toward or away
from the listening area. To pivot the Sonic Eye, apply light pressure to
the tweeter ring and the outside edge of the midrange. Do not apply
pressure to the midrange cone or the tweeter dome. If you have any
questions about how the Sonic Eye should be adjusted, consult your
authorized Sonance dealer.
Step 3
Tighten the four screws on the front of
the baffle. The Flexbars will
automatically begin clamping the
speaker. When you notice resistance on
the four screws, the speaker has been
clamped successfully.
Here are some suggestions:
Orient the Sonic Eye toward the listening area if the speakers are
widely separated and the music fails to blend into a central image
when the system is operated in stereo.
The flange is designed to flex and
conform to any small imperfections in
the wall surface. The screws should not
be tightened so far that the flange bows
out.
When using the Ellipse LCR in a home theater, point the Sonic Eye on
all three speakers towards the listening position for more accurate
sound.
Step 4
After the four Flexbar screws are
tightened the grille can be installed.
Insert about half of the grille into the
groove at the edge of the speaker.
Gently fit the remaining half of the grill
into the speaker by working your hands
around the speaker fitting the grille into
the groove as you go along.
Note: The torque applied to the
mounting screws can be adjusted for
proper grille fit.
3
Ellipse 1.0 LCR
TECHNICAL ASSISTANCE AND SERVICE
The Technical Assistance Department at Sonance is available at (800)
582-0772 or (949) 492-7777 to answer any questions concerning the
operation and installation of your speakers between the hours of 7:00
AM and 5:00 PM Pacific time, Monday through Friday, except holidays.
Speaker Design
In-ceiling LCR infinite baffle
Tweeter
Midrange
Woofer
1/2" (13mm) Cloth dome, pivoting
4" (102 mm) Polypropylene cone, pivoting
6-1/2" (165 mm) Black glass composite cone with a
rubber surround
In the event your unit should need repair or service, you may return
the unit to your authorized dealer or use the following guidelines:
Frequency Response 50Hz – 20kHz ±3dB
1. Be prepared to state the model number and / or serial number,
date of purchase and dealer's name and address when calling.
Impedance
Power
8 ohms nominal, 6 ohms minimum
5 watts minimum; 125 watts maximum
89dB 1W / 1m
Sensitivity
2. Contact Sonance directly at (800) 582-0772 or (949) 492-7777 or
Grille
Aluminum
Speaker Dimensions 10-1/2" (267mm) x 15-1/2" (394mm) x 5-7/8" (149mm)
3. If you are returning the product directly to Sonance, call us to
obtain a return authorization number before shipping. YOU MUST
HAVE PRIOR AUTHORIZATION TO RETURN YOUR UNIT.
Cutout Dimensions
9" (171mm) x 14" (356mm) elliptical
Weight
8.0 lbs (3.63 kg) each
4. The original packaging must be used. If the original packaging is
unavailable, replacements can be obtained from Sonance for a
small fee.
Ellipse 2.0 LCR
Speaker Design
In-ceiling LCR infinite baffle
5. Ship the product via a package delivery service such as UPS or
Federal Express. Please do not use the U.S. Postal service.
Tweeter
Midrange
Woofer
1" (25mm) Aluminum dome, pivoting
4" (102 mm) Aluminum cone, pivoting
6-1/2" (165 mm) Black aluminum cone with a rubber
surround and extended pole piece
6. Write the return authorization number on the outside of the box.
7. Ship to:
Attn: Quality Assurance Department
Sonance
Frequency Response 40Hz – 20kHz ±3dB
Impedance
Power
6 ohms nominal, 4 ohms minimum
5 watts minimum; 150 watts maximum
90dB 1W / 1m
212 Avenida Fabricante
San Clemente, CA 92672-7531
Sensitivity
8. FREIGHT COLLECT SHIPMENTS WILL BE REFUSED !
Grille
Aluminum
Speaker Dimensions 10-1/2" (267mm) x 15-1/2" (394mm) x 5-7/8" (149mm)
Cutout Dimensions
9" (171mm) x 14" (356mm) elliptical
Limited Lifetime Warranty
Sonance warrants to the original retail purchaser only that this Sonance product will be free
from defects in materials and workmanship, provided the speaker was purchased from a
Sonance Authorized Dealer after September 1, 2003. Purchases made before that date carry a
limited 5 year warranty.
Weight
9.0 lbs (4.1 kg) each
10 1/2" (267mm)
Defective products must be shipped, together with proof of purchase, prepaid insured to the
Sonance Authorized Dealer from whom they were purchased, or to the Sonance factory at the
address listed on this installation instruction manual. Freight collect shipments will be refused.
It is preferable to ship this product in the original shipping container to lessen the chance of
transit damage. In any case, the risk or loss or damage in transit is to be borne by the
purchaser. If, upon examination at the Factory or Sonance Authorized Dealer, it is determined
that the unit was defective in materials or workmanship at any time during this warranty
period, Sonance or the Sonance Authorized Dealer will, at its option, repair or replace this
product at no additional charge, except as set forth below. If this model is no longer available
and can not be repaired effectively, Sonance, at its sole option may replace the unit with a
current model of equal or greater value. In some cases where a new model is substituted, a
modification to the mounting surface may be required. If mounting surface modification is
required, Sonance assumes no responsibility or liability for such modification. All replaced parts
and product become the property of Sonance. Products replaced or repaired under this
warranty will be returned to the original retail purchaser, within a reasonable time, freight
prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster,
misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use,
voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of
the product which has not been authorized or approved by Sonance. This Warranty also
excludes normal cosmetic deterioration caused by environmental conditions. This Warranty will
be void if the Serial Number on the product has been removed, tampered with or defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in
materials or workmanship as warranted above, the purchaser's sole remedy shall be repair or
replacement as provided above. In no event will Sonance be liable for any incidental or
consequential damages arising out of the use or inability to use the product, even if Sonance
or a Sonance. Authorized Dealer has been advised of the possibility of such damages, or for
any claim by any other party.
14" (356mm)
Some states do not allow the exclusion or limitation of consequential damages, so the above
limitation and exclusion may not apply. All implied warranties on the product are limited to the
duration of this expressed Warranty. Some states do not allow limitation on the length of an
implied warranty. If the original retail purchaser resides in such a state, this limitation does not
apply.
w
w
w
.
s
o
n
a
n
c
e
.
c
o
m
Sonance • 212 Avenida Fabricante • San Clemente, CA 92672-7531, USA • (800) 582-7777 or (949)492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772
©2007 Sonance. Sonance, Sonic Eye, Flexbar, and Sonafill are trademarks of Dana Innovations.
|