Soehnle Postal Equipment 9222 User Manual

FOR MEASURABLE SUCCESS  
COUNTING SCALE 9222  
Operating Manual  
Trade, Commerce and Industry  
 
1. GENERAL INFORMATION  
Application  
The Soehnle Professional Counting Scale 9222 is  
designed for weighing goods and calculating unit  
totals.  
Cleaning  
All you need to clean the equipment is a damp  
cloth and a commercial cleaning agent. Do not use  
scouring agents.  
Safety Notices  
Maintenance and Service  
Read the operator manual carefully before using  
the equipment for the first time. It contains impor-  
tant information on the installation, correct use and  
maintenance of the equipment.  
The scales do not require regular maintenance.  
However, it is worth checking their accuracy at  
regular intervals. The frequency will depend on  
the application and condition of the scales.  
The manufacturer shall not be held liable if the  
following notices are not complied with: Observe  
the regulations in place when using electrical com-  
ponents with important safety requirements. Never  
carry out work on energised scales. Improper instal-  
lation will invalidate the warranty. The electrical  
connections must comply with the ratings printed  
on the power supply unit.  
The equipment is designed for use in buildings.  
Note the permissible operating ambient tempera-  
tures (specifications).  
The equipment complies with electromagnetic  
compatibility requirements. Avoid exceeding the  
maximum values specified in the standards. If  
you have any problems, contact your Soehnle  
Professional service partner.  
Note  
In accordance with European directive 89/336/EEC  
this device is fitted with noise suppression. How-  
ever, the display reading can be affected by extreme  
electrostatic or electromagnetic interference, e.g.  
using a radio or mobile phone in the immediate  
vicinity of the equipment. At the end of the inter-  
ference the product can be used again for its pur-  
pose, however it may need to be switched on  
again. In the event of permanent electrostatic inter-  
ference we recommend earthing the platform.  
This device is a measuring instrument. Drafts, vibra-  
tions, rapid changes in temperature and solar irradi-  
ation can affect the scale reading.  
The scales comply with safety rating IP 54. High air  
humidity, steam, aggressive fluids and contamination  
must be avoided.  
3
 
ENGLISH  
Counting Scale 9222  
Warranty/Liability  
Specifications  
If the supplied goods contains a defect attributable  
to Soehnle Professional, Soehnle Professional shall  
be entitled to rectify the defect or provide a replace-  
ment. Replaced parts shall become the property  
of Soehnle Professional. Should the rectification  
or replacement not prove unsatisfactory, statutory  
provisions shall apply. The warranty period is for  
2 years and starts on the day of purchase. Please  
keep your invoice as a receipt. For service please  
contact your dealer or the Soehnle Professional  
customer service department.  
Weighing range:  
Numeral script:  
Accuracy:  
6 kg / 15 kg / 50 kg  
0,2 g / 0,5 g / 1 g  
1/30.000 / 1/30.000 / 1/50.000  
Operating temperature: 0° – 40°C  
Power supply:  
Interface:  
9V / 500 mA, AC-Adapter;  
6V-Akkus eingebaut  
RS-232  
Disposal  
Faulty batteries must be disposed of in  
accordance with national and local envi-  
ronmental regulations and raw materials  
must be recycled.  
No liability shall be accepted in particular for  
damage arising from the following situations:  
Unsuitable, improper storage or use, faulty assem-  
bly / commissioning by the buyer or third parties,  
natural wear, modification or tampering, faulty or  
negligent handling, in particular overuse, chemical,  
electro-chemical, electrical interference or humidity,  
insofar as these are not attributable to Soehnle  
Professional.  
PB  
Should operational, climatic or other effects result  
in a significant change to the operating conditions  
or the condition of the material, the warranty for  
the overall operation of the equipment shall be-  
come invalid. Where Soehnle Professional provides  
a warranty in individual cases, this implies freedom  
from defects to the goods for the duration of the  
warranty period.  
Soehnle Professional GmbH & Co. KG  
Manfred-von-Ardenne-Allee 12  
DE-71522 Backnang  
Phone +49 (0) 71 91 / 34 53-0  
Keep the original packaging in case it is required  
for returning the goods.  
Fax  
+49 (0) 71 91 / 34 53-211  
4
 
2. USING THE SCALES FOR THE FIRST TIME  
Supplied Contents  
Switching on/off  
On  
button, and off  
Scales  
Switch the scales on using the  
Off  
button (see illustration). Do not load  
Platform  
Wall power supply  
using the  
the scales at this point.  
Attention: Carefully place the items to be weighed  
on the scales. Do not permanently load the platform.  
Avoid impacts or overloading beyond the specified  
maximum load as this could damage the scales.  
Assembling the Scales  
1. Remove the cover from the platform and place  
the platform on the scales.  
2. Assemble the scales at the application point.  
3. Use the adjustable legs and the spirit level  
to ensure the scales are mounted horizontally.  
4. Attach the wall power supply. The installed  
battery charges up (LED lit).  
5. The scales are ready for operation.  
Connection  
for other  
scales  
RS-232C  
interface  
(inactive)  
Off  
On  
ON and OFF  
buttons  
5
 
ENGLISH  
Counting Scale 9222  
3. INPUT AND CONTROL  
Control Keys  
01  
13  
02  
14  
03  
15  
ALARM  
x1  
7
4
1
0
8
5
2
.
9
6
Off  
On  
0
04  
16  
05  
17  
06  
18  
ADD  
TOTAL  
PLU  
07  
19  
08  
20  
09  
21  
A
3
B
10  
22  
11  
23  
12  
24  
GN R  
C
PLU shortcut keys (to call up  
stored unit weights directly)  
Sum total key (show overall unit totals  
and weights after adding)  
01  
13  
12  
24  
To input numerical values  
PLU shortcut keys for saving,  
loading or modifying saved unit weights  
("Product Look Up")  
0
9
PLU  
Input the reference weight  
(unit weight)  
x1  
Reset display to zero /  
delete input  
C
Input the reference amount  
(unit total)  
Zero setting key  
Tare  
0
Toggle key between 2 scales  
(inactive)  
A
B
Change the display between gross,  
net and tare weights  
Limit setting  
ALARM  
(max./min total weight/unit total)  
Adding values  
ADD  
6
 
Display  
NET  
kg  
g
Total weight  
PLU  
kg  
g
Reference weight or amount  
Calculated unit total  
A B C D  
Hi  
Lo  
ACC  
Display Symbols  
Charge battery  
Net weight  
Display in kilograms  
Display in grams  
Idle  
Zero report  
Load above upper target weight  
Load below lower target weight  
PLU memory  
Sum total memory  
7
 
ENGLISH  
Counting Scale 9222  
4. WEIGHING AND COUNTING  
Zero setting  
Counting  
If after powering up the scales there is  
Counting with an unknown unit  
weight (method 1)  
0
no load on the scales but the display is  
not zero, press  
0
. Possible zero setting  
Place the counted reference unit  
total on the platform.  
range –2%…+2% of the weighing range.  
The display shows  
.
Enter the unit total and press  
within 4 seconds to calculate the  
unit weight, otherwise the input will  
be deleted automatically.  
Calculating / Deducting  
the Tare Weight  
Other amounts placed on the scales will now also  
be counted.  
Weighing with the tare weight  
calculated  
Place the container on the platform.  
Press  
Counting with an unknown unit  
weight (method 2)  
.
The display goes to zero.  
When the scales are unladen press  
. "SAMPLE" appears in the sec-  
ond line of the display and "100"  
in the third line.  
Enter the unit total.  
Place the counted reference unit  
total on the platform.  
The display shows  
.
Weighing with the tare weight  
manually entered  
Enter the known tare weight in  
grams.  
Press  
display flashes.  
until the value in the  
Wait briefly until the scales have  
calculated the unit weight.  
Place the container on the platform.  
Place the items to be weighed on  
the scales.  
Other amounts placed on the scales will now also  
be counted.  
The net weight is displayed when the scales come  
Counting with an unknown unit  
weight (method 3)  
to rest. The display shows  
.
Place the counted reference unit  
total on the platform.  
Deleting the Tare Weight  
When the scales are unladen press  
.
Press  
. "SAMPLE" appears in the  
second line of the display and "100"  
in the third line.  
Enter the unit total.  
8
 
Remove the reference pieces from  
the platform and wait briefly until  
the scales have calculated the unit  
weight.  
"LoAd. Hi" is displayed.  
Enter upper target weight.  
Press  
ALARM  
.
"LoAd. Lo" is displayed.  
Other amounts placed on the scales will now also  
be counted.  
Enter lower target weight.  
ALARM  
Press  
.
If the limits are exceeded a signal sounds and the  
Compensating fluctuating weights  
Place other reference pieces on the scales. Press  
to calculate the exact unit weight.  
warning arrow flashes on  
or  
.
Removing the limits  
C
Select the target levels and delete with  
.
Counting with a known unit weight  
x1  
Enter the known unit weight in  
grams.  
Press  
Sum Total  
x1  
within 4 seconds, other-  
Calculate the unit weight as  
described in "Counting".  
ADD  
wise the input will be deleted auto-  
matically.  
Place the goods on the scales and  
Other amounts placed on the scales will now also  
be counted.  
wait until  
appears.  
and empty the scales.  
ADD  
Press  
Place more goods on the scales and  
wait until  
appears.  
ADD  
Setting Target Weights /  
Press  
again and empty the  
Quantities  
scales...  
A top and bottom limit can be set for  
The number of added readings is shown on  
the left. Up to 180 readings can be stored.  
ALARM  
weight or counted readings.  
ALARM  
Press  
.
Attention  
Changing the PLU deletes the sum total memory.  
The same unit totals cannot be added one after  
another as the scales will assume that the plat-  
form has not been cleared beforehand. A warn-  
ing sounds.  
"PCS. Hi" is displayed.  
Enter the maximum unit total.  
Press  
ALARM  
.
"PCS. Lo" is displayed.  
Enter the minimum unit total.  
ALARM  
Press  
.
9
 
ENGLISH  
Counting Scale 9222  
Displaying the sum total  
Selecting PLUs  
Press  
.
Selecting PLUs stored under  
01  
12  
24  
the PLU shortcut keys  
13  
Deleting the sum total in the memory  
Press the required PLU shortcut key. For the  
lower limit press the key again.  
C
Press  
.
PLU is activated.  
Saving PLU (Product Look Up)  
PLUs are used to store information on parts that are  
used regularly, so that the data can be retrieved  
quickly from the memory. The PLU number contains  
data on the tare weight, name and unit weight.  
Depending on the model, the scales can store up  
to 1000 PLUs.  
Selecting the PLUs stored under 0–199  
PLU  
Press  
until you hear the audible signal.  
Enter the PLU number.  
PLU  
Press  
.
PLU is activated.  
Note: The PLU numbers of the shortcut keys and the  
numerical keys are shown identically on the right.  
Note the displayed unit weight (e.g. a different value  
may be stored under PLU-013 via the PLU shortcut  
keys and the numerical keys).  
01  
13  
12  
24  
Saving under the PLU shortcut keys  
Calculate the unit weight  
as described in "Counting".  
PLU  
PLU  
Press  
.
Press the required PLU shortcut key,  
Editing PLUs  
01  
13  
e.g.  
.
Call up the PLU to be changed.  
Press PLU . The unit weight will flash.  
Enter a new unit weight.  
For the lower value press the PLU  
shortcut key again.  
PLU  
PLU  
Press  
.
Press  
.
PLU is programmed.  
The new PLU is stored.  
Saving under the numerical keys 0-999  
Calculate the unit weight  
as described in "Counting".  
Programming the PLUs  
PLU  
with Tare Weight  
PLU  
Press  
.
Place the tare weight on the scales.  
Enter the required numerical value  
Press  
.
for the PLU number.  
Continue as described in "Saving PLU  
(Product Look Up)".  
PLU  
Press  
.
PLU is programmed.  
10  
 
Programming the Tare Weight  
Zero point calibration  
< A/D reading  
as Standard  
Place the tare weight on the scales before  
switching them on.  
< reading 0 (grams)  
< "Pnt 0"  
Switch on the scales.  
Make sure that the scales are empty.  
Wait until the A/D reading (1st row) is stable,  
Continue as described in "Saving PLU  
(Product Look Up)".  
then press  
to continue.  
Setting the calibration weight  
Error Messages  
< A/D reading  
< calibration weight 0 (grams)  
Max. weighing range exceeded  
> Take the items off the scales  
< "Pnt. CAL"  
Place the calibration weight (min. 1/3 of the  
weighing range) on the platform. Enter the  
weight in grams via the keypad. Wait until  
Piep  
Zero setting not possible  
> Deviation from zero point too high  
the A/D reading is stable, then press  
.
User Calibration  
The calibration was successful.  
Press  
and switch on the scales with the  
On  
key.  
C
Select using  
"CAL 4"  
Error Message "Err. Ad"  
> Calibration weight too low  
and confirm using  
.
> Deviation from calibration weight  
too high  
Selecting the maximum weight  
Select the maximum weight in kg  
C
(2nd row) using  
with  
and confirm  
Use a calibration weight with at least 1/3 of the  
weighing range. You should calibrate in the range  
in which you need to achieve the highest degree  
of accuracy.  
.
The power-up initialisation starts when the  
scales are discharged.  
11  
 
ENGLISH  
Counting Scale 9222  
Soehnle Professional GmbH & Co. KG  
Manfred-von-Ardenne-Allee 12  
DE-71522 Backnang  
Phone +49 (0) 71 91 / 34 53-0  
Fax  
+49 (0) 71 91 / 34 53-211  
Scales, System Solutions And Special Developments  
07/2009 470.070.002  
 

Snapper Air Cleaner 31H700 User Manual
Sonance Speaker System LCR1 User Manual
Sony Cassette Player 30TW User Manual
Sony Cell Phone 1904 User Manual
Sony Headphones MDR E11LP User Manual
Sony Home Security System Ssc M383 User Manual
Sony Projection Television KV 21FS120 User Manual
Sprint Nextel Network Card S720 User Manual
Sylvania DVD Player DVL700D User Manual
Sylvania Flat Panel Television A01PDUH User Manual