Microwave Drawer®
InstallatIon Manual
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE ThIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE ThESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES ANd dImENSIoNS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on pages 2 and 3. See Figure 1 (for 24") or Figures 3 and 4 (for 30") .
ImPoRtANt NotES to thE CoNSUmER
UNPACkING yoUR mICRoWAvE dRAWER
Keep this manual with your Operation Manual for future
reference.
• Remove all packing
materials from inside
theMicrowaveDrawer.
DO NOT REMOVE
THE WAVEGUIDE
COVER, which is
located on the top
of the Microwave
Drawer.
Sealing
surface
• As when using any microwave oven generating heat, there are
certain safety precautions you should follow. These are listed
in the Operation Manual. Read all and follow carefully.
Waveguide
cover
• Be sure your Microwave Drawer is installed and grounded
properly by a qualified installer or service technician.
ImPoRtANt SAfEty INStRUCtIoNS
If the information in this manual is not followed
exactly, a fire or electrical shock may result that could cause
property damage, personal injury or death.
Sealing
surface
• Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misaligned or bent
Oven
cavity
To reduce the risk of tipping, the Microwave
Drawer must be secured by a properly installed Anti-Tip
block.
drawer, damaged drawer seals and sealing surfaces, broken
or loose Microwave Drawer guides and dents inside the cavity
or on the front side of the drawer. If there is any damage, do
not operate the Microwave Drawer and contact your dealer or
a SHARP AUTHORIZED SERVICER.
• This Microwave Drawer must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
ImPoRtANt NotES to thE INStALLER
• Read all of the Installation Manual before installing the
Microwave Drawer.
Never leave children alone or unattended in
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
• Remove all packing material before connecting the electrical
supply.
Stepping, leaning or sitting on the drawer
may result in serious injuries and can also cause damage to the
Microwave Drawer.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
• Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch
Stop/Clear to prevent unintended use.
TINSKB147MRR1
E 1
30" mICRoWAvE dRAWER mEASUREmENtS
Figures 3, 4 and 5 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.
A. 6" (152.40 mm)
C
A
B
B. Suggested electrical
outlet location*
E
D
This Microwave Drawer can be installed below any electric or
gas wall oven.
C. Anti-Tip block
D. 5" (127 mm)
F
G
K
H
* Can also be installed using an electrical outlet in an adjacent
cabinet within the area where the provided electrical cord can
reach. Power cord access hole in cabinet should be a minimum
E. 3-1/2" (88.90 mm)
F. 4" (101.60 mm)
I
Q
J
I
G. 28-7/16" (722.31 mm)
opening
N
L
1 1/2" diameter hole and deburred of all sharp edges.
H. 14-13/16" (376.24 mm)
to bottom of Anti-Tip
block
IMPORTANT
Always allow sufficient power cord length to the
M
electrical outlet to prevent tension.
O
Always check electrical codes for requirements.
I. Allow 3/4" (19.05 mm)
overlap
A. 84" (2133.6 mm) wall
cabinet
P
J. 23-1/2" (596.9 mm)
minimum depth
B. Optional wall oven
cutout illustrated in
sketch
Figure 4
K. Allow 3/16" (4.76 mm) overlap
L. 36" (914.4 mm) countertop height
M.Allow 7/16" (11.09 mm) overlap
N. Floor must support 100 lb (45.4 kg)
C. Suggested electrical
outlet location*
D. 6" (152.40 mm)
E. Anti-Tip block
A
O. 19" (482.6 mm) to top of floor (recommended)
P. 30" (762 mm) cabinet minimum
F. 3-1/2" (88.90 mm)
G. 5" (127 mm)
B
Q. 14-13/16" (376.24 mm) opening
H. 4" (101.60 mm)
I. 2" (50.8 mm) minimum
E
D
C
J. 28-7/16" (722.3 mm)
opening
F
L
A
C
G
B
J
K. Allow 3/16" (4.76 mm)
overlap
I
A. 21-5/8"
(549.28 mm)
B. 4-11/16"
(119.06 mm)
C. 1-3/4"
(44.45 mm)
D. 21-7/8"
(555.63 mm)
H
J
K
G
F
L. 14-13/16" (376.24 mm)
to bottom of Anti-Tip
block
O
M
N
M
I
Q
M.Allow 3/4" (19.05 mm)
overlap
P
D
N. 23-1/2" (596.9 mm)
minimum depth
H
R
E
E. 30" (762 mm)
F. 15" (381 mm)
O. 14-13/16" (376.24 mm)
opening
Figure 5
S
P. Allow 7/16" (11.11 mm)
overlap
G. 14-19/32" (370.68 mm)
Figure 3
H. 1-11/16" (42.86 mm) door thickness
I. 15" (381 mm) auto drawer opening
J. 4" (101.6 mm)
Q. Floor must support 100 lb (45.4 kg)
R. 19" (482.6 mm) to top of floor (recommended)
S. 30" (762 mm) cabinet minimum
ANtI-tIP BLoCk
NORMAL INSTALLATION STEPS
Anti-Tip block must also be moved
Anti-Tip block
6"
and installed. When installed to
the wall, make sure that the screws
completely penetrate the dry wall
and are secured in wood or metal
so that the block is totally stable.
When fastening, be sure that the
screws do not penetrate electrical
wiring or plumbing.
(152.4 mm)
ANTI-TIP BLOCK INSTALLATION INSTRuCTIONS
To reduce the risk of tipping of the drawer, the Anti-Tip block must
be properly installed located 14 13/16-inches above the floor on
which the Microwave Drawer will sit. The 6-inch Anti-Tip block
must be provided by the installer. See Figures 1 and 6 (for 24") or
Figures 3, 4 and 6 (for 30"). The Anti-Tip block prevents serious
injury that might result from spilled hot liquids.
3 1/2"
(89 mm)
Figure 6
If the Microwave Drawer is ever moved to a different location, the
E 3
ELECtRICAL oUtLEt
dRAWER INStALLAtIoN
Suggested electrical
outlet location*
5" (127 mm)
Mounting
flange
4"
(101.6 mm)
Figure 8A
Parts supplied
Figure 7
1. Place the drawer adjacent to the wall or
cabinet opening. Plug the power supply cord
into the electrical outlet.
The electrical requirements are a 120 volt 60 Hz, AC only,
15 amp. or more protected electrical supply. It is recommended
that a separate circuit serving only this appliance be provided.
2. Carefully guide the drawer into the prepared
opening. Avoid pinching the cord between
the oven and the wall.
4 Screws
The drawer is equipped with a 3-prong grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded. Should you only have a 2-prong outlet, have a qualified
electrician install a correct wall receptacle.
Figure 8B
3. Slide the drawer all the way until the
mounting flange is flush with the face of the cabinet. See
Figure 8A.
Note: If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or service person.
4. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16" bit. See Figure 8A.
* Can also be installed using an electrical outlet in an adjacent cabinet
within the area where the provided electrical cord can reach.
5. Secure the drawer with the 4 screws supplied. See Figure 8B.
Always check electrical codes for requirements.
modEL ANd SERIAL NUmBER LoCAtIoN
GRoUNdING INStRUCtIoNS
The name plate includes model and serial number. Open the
Microwave Drawer fully. The label is beyond the back wall of
the microwave cavity facing up from the flat surface.
This appliance must be grounded. The Microwave Drawer is
equipped with a cord having a grounding wire with a grounding
plug. It must be plugged into a wall receptacle that is properly
installed and grounded in accordance with the National
Electrical Code and local codes
CARE, CLEANING ANd mAINtENANCE
Refer to the Operation Manual for cleaning instructions.
and ordinances. In the event of
3-Prong plug
an electrical short circuit,
grounding reduces risk of
electric shock by providing an
escape wire for the electric
current.
BEfoRE yoU CALL foR SERvICE
Read the BEFORE YOU CALL and operating instruction sections
in your Operation Manual. It may save you time and expense.
The list includes common occurrences that are not the result of
defective workmanship or materials in this appliance.
Grounding pin
– Improper use
of the grounding plug can result
in a risk of electric shock. Do
not use an extension cord. If
3-Prong receptacle
Grounded receptacle box
Refer to the warranty in your Operation Manual for Sharp’s
service number and address. Please call or write if you have
inquiries about your microwave product and/or need to order
parts.
the power supply cord is too short, have a qualified electrician
or serviceman install an outlet near the appliance.
SHARP ELECTRONICS OF CANADA LTD
335 Britannia Road East • Mississauga, Ontario • L4Z 1W9
E 4
|