液晶カラーテレビ用壁掛け金具
LCD Color TV Wall-Mount Bracket
Téléviseur couleur LCD et le support de
montage au mur
AN-65AG1
Wandhalter für LCD-Farbfernsehgerät
Ménsula de montaje el TV color de cristal
líquido en la pared
取扱説明書
OPERATION MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUAL DE MANEJO
・壁用金具取付ネジは同
梱しておりませんので
市販品をお求めください。
• The wall bracket mounting screws are not in-
cluded with the product, so please separately
purchase off-the-shelf screws.
• Les vis de fixation du support à base ne sont
pas fournies avec le produit; veuillez donc
acheter séparément des vis en vente dans le
commerce.
• Die Wandhalter-Befestigungsschrauben sind
nicht im Lieferumfang des Produkts enthalten.
Besorgen Sie sich daher bitte im Handel
erhältliche Schrauben.
適応機種 Used Models / Modéle utilisé /
Gebrauchtes Modell / Modelo usado /
• Los tornillos de montaje de ménsula en la pared
no vienen con el producto, compre los tornillos
por separado en la tienda.
LC-6 5 GE1
Please strictly observe the following.
Special skill is required to install the LCD color
TV, so please have it installed by a contractor
specializing in such installation. The customer
should not attempt to install the TV. Sharp shall
not be responsible for improper installation or
any accidents, damage, or injury resulting from
improper installation.
To the contractor
• To ensure the safety of the customer, conduct the
design so that the strength of the installation
location is sufficiently strong to support the weight of
the LCD color TV and the wall-mount bracket.
• Be sure to use two or more people to conduct the
work.
• The wall installation screws for the wall-mount
brackets are not included with the fixtures. Select
off-the-shelf screws that match the wall.
Outside dimension drawing
Base bracket
(Mark A: At a height at the center of the
LC-65GE1 screen)
558
528
343
280
A
B
18
518
220
220
Wall-mount bracket
440
280
26
14
A
B
460
35
440
468
478
Unit: mm
E-2
Accessories packaged with the TV
Base bracket: 1
Wall-mount bracket: 1
Angle setup bracket: 2
*Assembly completed
for perpendicular
installation.
Allen wrench: 1
Screws
For the angle setup
bracket
For installing the wall-
mount bracket unit
For fastening the
wall-mount bracket
Operation manual
(This manual)
M6 length:
8mm (2 screws)
M8 length:
15mm (2 screws)
M10 length:
30mm (4 screws) with
hexagonal sockets
*The screw notation M6 means the diameter of the threaded part is 6 mm.
*Please also store the screws that are not used.
Please use the following
• Wall installation screws (off-the-shelf) 17
Be sure to consult the dealership or a qualified contractor when installing the TV.
• Stand hole covers × 2 (Included with the LCD color TV)
• A plumb bob made by tying a coin with a hole in it to the end of a string.
• A pin, such as a thumbtack
• Cushion, soft cloth, etc.
• Tool (Phillips head screwdriver)
Installation location
• LCD color TVs have a viewing angle (range in which the image can be viewed correctly). The
best viewing position is from directly in front of the screen. Determine the TV installation location
after taking into consideration the viewing posture, line of sight, and the visual and aural ranges.
• Sharp shall bear no responsibility for damages, etc., caused by the LCD color TV falling due
Caution
to insufficient installation strength or improper installation.
Weight table (Unit: kg)
E-3
Wall-Mount Bracket Installation
Determine the location where the base bracket will be
installed.
(1) Use tape or other means to mark the measured positions
on the wall where the display will be installed. The center
of the “X” drawn from the four corners of the square marks
the center of the panel.
Included part
1
Base bracket
(2) Take the coin with the string and align it perpendicular to
the base bracket.
Use a pencil, etc., to mark the two screw hole locations.
Dimension lines
used as a guide
Cellophane tape, etc.
Cellophane tape, etc.
shaped screw holes
Wall-mount bracket
unit installation hooks
Use a pencil, etc., to
mark the screw hole
position on the wall
behind the bracket.
String
Base
bracket
outline
Center
line
Position the base
bracket so that the
center of it is aligned
with the string.
Display
outline
Position the base
bracket so that the
perpendicular parts
of it are parallel with
the string.
Weight
1572mm
*When marking on the wall, use a material that will not leave a permanent mark on
the wall and get the approval of the customer before beginning the work.
Tighten the screws
Temporarily remove the base bracket from the wall and loosely screw in off-the-shelf screws (8
mm dia. × 2 screws) in the screw hole positions marked on the wall. At this time, the screw
heads should extend more than 4 mm above the wall so that the base bracket can be hung on
the screw heads. Hang the base bracket on the installed screws, check to make sure the
bracket is not sagging to the left or right, and then firmly tighten the screws. Use off-the-shelf
screws to secure the remaining screw holes (15 screws). (The screw hole diameter is 9 mm.)
2
Min. 4mm
Use the weight with the string
used in Step 1 to make sure
the bracket is perpendicular.
E-4
Installing the wall-mount bracket (For Model 65 inch Separate Type)
• Be sure to use at least two people to perform the wall-mount bracket installation work for the LCD color TV.
• The installation work must be conducted while the LCD color TV is standing upright, so be careful that it
Caution
does not fall over.
Place the LCD color TV on a strong stand
1
about 20 to 30 cm high and remove the
two back terminal covers.
Two terminal covers,
top and bottom
Remove the terminal covers while
the LCD color TV is standing upright.
(2 covers top and bottom)
Remove the 3 fastening screws from both the left and right stands on the back of the
2
LCD color TV.
Keep the removed screws (short × 2 screws, long × 4 screws).
Long screws
Short screw
(1) Remove the 2 screws from each of the stand edge covers (total of 4 screws from the
3
left and right sides).
Use the removed screws (total of 4 screws) as shown in Step 2 on page 9.
(2) Remove the stand fastening screws (2 screws each on
the left and right sides).
Removing the edge covers reveals
the stand fastening screws in the
center of the stands, so remove
these screws.
Edge covers
Edge cover screws
E-5
Installing the wall-mount bracket (Continued)
Connect the system cables and power cord to the terminals on the back
4
of the LCD color TV.
System cables
Power cord
Use the cable holder at the center of the back of the LCD color TV and the cable holders
holding the speaker cables to connect the system cables.
5
6
Cable holders
Surround the system cables.
(1) Pass through
the band.
(2) Pull the band
forward and
catch it on
the hook.
Included part
Remove the screw hole plugs (4 plugs) of
the wall-mount bracket on the back of the
TV and then screw in the 4 wall-mount
Allen wrench
bracket unit screws (hexagonal socket
screws, M10 length: 30 mm) that are in-
Hexagonal socket screws
cluded with the wall-mount bracket unit.
Wall-mount bracket
(M10 length: 30 mm)
Screw hole plugs (4 plugs)
Mark A
Included hexagonal socket screws (4 screws)
Carefully keep the removed screw hole plugs.
Use an Allen wrench to screw in the included
hexagonal socket screws into the Mark A holes.
E-6
Set the angle of the wall-mount bracket
• Please perform this work before mounting the LCD color TV on the wall.
Caution
• When setting the angle of the wall-mount bracket, be careful not to pinch your fingers, etc.
Remove the perpendicular positioning screws from the wall-mount bracket (2 screws
1
each on the left and right sides).
Hole at the very top
Included part
Angle setup bracket screws
M8 length:
15mm (2 screws)
Angle setup bracket
These screws are used for the angle
setup in Step 2.
Assemble the included angle setup brackets as shown in the illustration and then use
2
them to set the TV to the desired angle.
For the screws, use the included angle setup bracket screws (M8 length: 15 mm × 2 screws)
and screws removed in Step 1.
First loosely tighten the 4 screws and then securely tighten them after the angle setup bracket
is set to the desired position.
The numbers 5, 10, 15, and 20 at the
screw holes mean that the higher the
number, the more the LCD color TV
slants downward. The angle that can
be set is limited depending on the
TV model.
0
20
0
2
15
15
10
5
10
5
E-7
Remove the stands
• Be sure to use at least 3 people for the work from this point onward.
Caution
• Be very careful when holding the LCD color TV at a slant or when lifting it up.
Lift up the LCD color TV and remove the stand.
While the stand is being held down, lift up the LCD color TV to remove it from the stand.
*Remove the LCD color TV from the stand while tipping it backward slightly.
1
Hold down the stand so that
it does not move.
Temporarily place the LCD color TV on a cushion or soft material and install the stand
2
hole covers that are included with the LCD color TV.
Hold the LCD color TV at a slant and align the stand hole covers (included with the LCD color
TV) with the stand insertion locations.
Use the screws removed during Step 3 on page 6 to attach the stand hole covers and speaker
cables.
Stand hole cover
E-8
Installing the LCD color TV on the wall
• Be sure to use at least 4 people when installing the LCD color TV to the base bracket.
Caution
• Be sure to perform Steps 1 and 2 below. Only performing Step 1 could result in the display falling and
injuring someone.
Install the wall-mount bracket attached to the LCD color TV to the base bracket.
Hang the square holes of the wall-mount bracket on the hooks (see page 5) of the base
1
bracket unit.
Check to make sure the hooks are securely inserted into the notches at the top of the slanted
side of the wall-mount bracket unit.
Hook
Notch
Wall
Included part
Fasten the screws in the wall-mount bracket
2
unit and bottom of the base bracket (Be sure
Wall-mount bracket fastening screws
M6 length: 8mm (2 screws)
to do this).
Fasten using the included wall-mount bracket
fastening screws (M6 length: 8 mm × 2 screws).
E-9
Printed in Japan
Imprimé au Japon
Printed on 100% post-consumer recycled paper.
Imprimé sur 100% de papier recyclé.
06E
DSC1
TINSE1082MPZZ (1)
|