LIGHT & EASY™ STEAM MOP
S3250CW
OWNER’S GUIDE
WWW.SHARKCLEAN.COM
S3250CW_11_IB_ENG_100913.indd
1
10-09-13 10:57 AM
corners. Keep power cord
away from heated surfaces.
21. Extreme caution should be
exercised when using this
appliance to clean stairs.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only
11. DO NOT unplug by pulling on
power cord. To unplug, grasp
the plug not the power cord.
Do not use extension cords or
outlets with inadequate current
carrying capacity.
22.Never use steam mop without
micro-fiber pad attached.
23.Keep your work area well lit.
1. Use the system only for its
WHEN USING YOUR SHARK®
24.Store steam mop indoors in a
cool, dry place.
intended use.
STEAM MOP, BASIC SAFETY
12. DO NOT put any objects into
openings. Do not use with any
opening blocked.
2. DO NOT use outdoors.
PRECAUTIONS SHOULD ALWAYS
25.To avoid circuit overload, do
not operate another appliance
on the same socket (circuit) as
the steam cleaner.
3. DO NOT leave the appliance
BE FOLLOWED, INCLUDING THE
unattended when plugged in.
13. DO NOT put hands or feet
under the steam mop. Unit
gets very hot.
FOLLOWING:
Always unplug the power cord
from the electrical outlet when
not in use and before servicing.
26.If an extension cord is
absolutely necessary, an
extension cord rated a
WARNING:
TO REDUCE
14. Use ONLY on flat, stable
horizontal surfaces. Do not use
on walls, counters, windows,
chairs or tables.
4. DO NOT allow the appliance
to be used as a toy. Close
attention is necessary when
used by or near children, pets
or plants.
THE RISK OF FIRE, ELECTRIC
minimum of 15 ampere, 14
gage cord should be used.
Cords rated for less amperage
may overheat. Care should be
taken to arrange cord so that
it cannot be pulled or tripped
over.
SHOCK OR INJURY READ ALL
INSTRUCTIONS BEFORE USING
YOUR LIGHT & EASY™.
15. DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or
other delicate, steam sensitive
materials.
5. Use only as described in this
manual.
DANGER OF SCALDING.
Please use caution when
6. Use only manufacturer’s
recommended accessories.
27.DO NOT leave unattended
when the system is connected
to a power supply or electrical
outlet. Turn off all controls
before unplugging the unit.
using the steam mop. The steam
16. DO NOT add cleaning
emitted from the openings is very 7. DO NOT operate the appliance
solutions, scented perfumes,
oils or any other chemicals to
the water used in this appliance
as this may damage the unit
or make it unsafe for use. If
you live in a hard water area,
we recommend using distilled
water in your steam mop.
with a damaged plug or cord,
hot.
or if the unit has been dropped,
damaged left outdoors or
POLARIZED PLUG:
28 DO NOT store unit with damp
or wet micro-fiber cleaning
pad attached. Never leave the
steam mop in one spot on any
surface for any period of time
with a damp or wet micro-fiber
cleaning pad attached as this
will damage your floors
dropped into water. To avoid
TO REDUCE THE RISK OF ELECTRIC
the risk of electric shock, do
not disassemble or attempt to
repair the appliance on your
own. Return the appliance to
EURO-PRO Operating LLC (see
warranty) for examination and
repair. Incorrect re-assembly
or repair can cause a risk of
electrical shock or injury to
persons when the appliance is
used.
SHOCK, this appliance has a
polarized plug (one blade is wider
than the other). As a safety
feature, this plug will fit into a
polarized outlet only one way. If
the plug does not fit fully into the
outlet, reverse the plug. If it still
does not fit, contact a qualified
electrician. Do not attempt to
defeat this safety feature.
17. When in use, NEVER turn
the appliance over or on its
side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS
OR PLANTS.
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand
high heat. Do not use on
18. Carefully remove the micro-
fiber pad immediately after you
have unplugged and allowed
the product to cool.
unsealed wood or unglazed
ceramic floors. On surfaces
that have been treated with
wax or some no wax floors, the
sheen may be removed by the
heat and steam action. It is
always recommended to test an
isolated area of the surface to
be cleaned before proceeding.
We also recommend that
you check the use and care
instructions from the floor
manufacturer.
8. To protect against a risk
of electric shock, DO NOT
immerse the steam mop into
water or any other liquids.
19. When cleaning the steam mop,
unplug the power cord from
the electrical outlet and clean
with a dry or damp cloth. Do
not pour water or use alcohol,
benzene or paint thinner on the
unit.
9. DO NOT handle plug or steam
mop with wet hands or operate
appliance without shoes.
10. DO NOT pull or carry by
power cord, use power cord
as handle, close a door on the
power cord, or pull the power
cord around sharp edges or
20 To reduce the risk of fire,
DO NOT use a flammable or
combustible liquid to clean a
floor.
TOLL FREE: 1-800-418-0934
S3250CW_11_IB_ENG_100913.indd 2-3
10-09-13 10:57 AM
Quick Start
fig. 5
fig. 3
fig. 4
fig. 1
fig. 2
ASSEMBLE
FILL
STEAM CLEANING
4 Plug in the mop. Wait 30
BACKSAVER
1
Fit together the extension tubes
as shown in the illustration.
(fig. 1)
3
Remove the cap to fill the
water tank. Use the filling flask
and funnel to fill the tank with
water to the “MAX FILL” line.
Replace the water tank cap.
(fig. 3)
5
Use the Shark® Light &
Easy™ with backsaver
benefit to access tight
areas. Press the release
button on the handle
to lock the Light &
seconds for the unit to heat up
and the steam to be ready.
2
Place the micro-fiber cleaning
pad underneath the mop head,
with quick fastener strips facing
up. Simply press the mop to the
pad to attach it. (fig. 2)
Push the handle toward the
mop head in a pumping motion.
Customize steam output by slow
or fast mopping with a forward
and backward motion. (fig. 4)
Easy™ Steam Mop in the
backsaver position. Press
the release button on the
handle again to straighten
the handle. (fig. 5)
TOLL FREE: 1-800-798-7398
S3250CW_11_IB_ENG_100913.indd 4-5
10-09-13 10:57 AM
Contents
GETTING STARTED.................................................................2
USING YOUR STEAM MOP...................................................6
USING YOUR ACCESSORIES...............................................9
STORAGE AND CARE OF YOUR STEAM MOP ..........10
TROUBLESHOOTING ............................................................12
WARRANTY AND REGISTRATION...................................13
Thank you for
purchasing
the Shark®
™
Light & Easy
Steam Mop.
This manual covers model number:
S3250CW 11
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1550 Watts
Water
Capacity: 250 ml (8 oz.)
TOLL FREE: 1-800-798-7398
S3250CW_11_IB_ENG_100913.indd 6-1
10-09-13 10:57 AM
English
Getting Started
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you
buy them, so you get a quality
Shark® Light & Easy™ Steam Mop.
c
b
a
d
f
e
fig. 1
fig. 2
a Upper Handle Tube with Backsaver
benefit
ASSEMBLY
3 Insert the assembled handle piece
into the steam mop base. Push the
tube base together until you hear a
click. (fig. 2)
IMPORTANT: Never use the Light &
1
Remove all the parts from the
package. Verify all the listed parts
are included.
Easy™ Steam Mop without attaching
a micro-fiber cleaning pad to avoid
damage to your floor and mop.
b Lower Tube
c Steam Mop Base
d 2 All-Purpose Cleaning Pads
e Filling Flask
2 Slide the Upper Handle Tube (the
tube with the handle) into the Lower
Tube (the short tube). Push the two
extension tubes together until you
hear them click into place. (fig. 1)
f Funnel
2
TOLL FREE: 1-800-418-0934
3
S3250CW_11_IB_ENG_100913.indd 2-3
10-09-13 10:57 AM
English
Getting Started - cont’d
Your micro-fiber cleaning
pads should be replaced
every 3 months to maximize
cleaning performance.
fig. 2
fig. 3
fig. 1
ATTACHING THE MICRO-FIBER PAD
Replacement micro-fiber pads are
by calling 1-800-418-0934.
FILLING THE WATER TANK
2 A filling flask and funnel are included
with your Light & Easy™ Steam Mop
to make filling the water tank easy.
Fill the flask with water and use the
funnel to pour it into the tank. Keep
the water level under the MAX FILL
line. (fig. 3)
1
Place the micro-fiber cleaning pad
on the floor with the quick fastener
strips facing up. Place the Light &
Easy™ Steam Mop on the top of the
pad to attach. (fig. 1)
IMPORTANT: Unplug the Light &
Easy™ Steam Mop before filling the
water tank with water. (fig. 2)
1
Remove the water tank cap by
turning it counter-clockwise to the
unlocked position. (fig. 3)
IMPORTANT: Only add water to
the tank. Chemicals or cleaning
solutions may be unsafe or cause
damage.
3 Replace the water tank cap and turn
it clockwise to the locked position.
4
TOLL FREE: 1-800-418-0934
5
S3250CW_11_IB_ENG_100913.indd 4-5
10-09-13 10:57 AM
English
Using Your Light & Easy™ Steam Mop
When you use your steam mop for the
first time or if you have not used the unit
in awhile, it may take a minute or two
for the water to travel through the pump
and into the heater to create steam. Get
it started by pumping the handle a few
times. If you have waited a few minutes
and you still do not see any steam,
reference the troubleshooting section
on page 11.
™
If your Light & Easy Steam
Mop stops steaming, it could
be out of water. Unplug the
power cord from the electrical
outlet and refill the water tank
at anytime.
fig. 1
fig. 4
fig. 2
fig. 3
fig. 5
IMPORTANT: Your steam mop needs
water to make steam! Never use your
steam mop without water in the tank.
1
Pull and twist the quick release
cord holder to unwrap the power
cord completely. (fig. 1) Plug into
a 120-volt electrical outlet. (fig. 2)
The “On” light will turn blue. If the
light does not turn on, reference the
troubleshooting section on page 11.
(fig. 3)
2 Wait 30 seconds for the boiler to
heat the water. Pump the handle
a few times to prime the pump,
activate steam and moisten the
micro-fiber pad. (fig. 4)
3 Mop with a forward and backward
motion to customize steam output
automatically. (fig. 5)
Sweep or vacuum your floors prior
to cleaning with your Light & Easy™
Steam Mop.
great quick cleaning products to
complement your Light & Easy™
Steam Mop.
6
TOLL FREE: 1-800-418-0934
7
S3250CW_11_IB_ENG_100913.indd 6-7
10-09-13 10:57 AM
English
Using Your Light & Easy™ Steam Mop - cont’d
Care of Your Light & Easy™ Steam Mop
fig. 1
fig. 1
fig.3
fig.2
AFTER USE AND STORAGE
4 To store the cooled Shark® Light &
1
When you have finished using the
Light & Easy™ Steam Mop, unplug
the cord from the outlet and place
the mop into the upright position
(fig. 1) and let the unit cool 2-3
minutes. Release steam by pumping
the handle several times.
Easy™ Steam Mop, hang on a large
hook. (fig. 3)
1
Clean under furniture and tight
areas using the Shark® Backsaver™
locking handle. Press the handle
release button and apply slight
pressure to bend the handle. The
Shark® Backsaver™ joint will lock at
a perfect, access-maximizing angle.
(fig. 1)
NOTE: If you want to store the
Light & Easy™ Steam Mop standing
upright, make sure it is leaning
against a wall for added support and
safety. Always store your Shark®
Light & Easy™ Steam Mop with the
micro-fiber cleaning pad removed.
Store away from children and high
traffic areas.
2 Carefully separate micro-fiber
cleaning pad from steam mop,
avoiding contact with the hot pocket
or dirt. (fig. 2)
2 Press the release button on the
handle again to straighten.
3 Empty the water tank before storage.
Remove the water tank cap and
empty the tank over a sink. Replace
the water cap.
8
TOLL FREE: 1-800-418-0934
9
S3250CW_11_IB_ENG_100913.indd 8-9
10-09-13 10:57 AM
English
Care of Your Light & Easy™ Steam Mop
Trouble Shooting
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Your steam-mop should be securely plugged into a
120V AC electrical outlet only.
The Light & Easy™
Steam Mop will not
turn-on.
Check your fuse or breaker.
If your unit still does not work, call 1-800-418-0934.
fig. 4
Light & Easy™
Steam Mop will not
make steam.
Is there water in the water tank? If not, add water to your
Steam Mop following instructions on page 5.
Light & Easy™
Steam Mop leaves
water on the floor.
Is your micro-fiber cleaning pad too wet? Unplug your
Steam Mop and change the micro-fiber cleaning pad.
Do not leave your steam-mop on the floor with a damp or
wet cleaning pad.
Light & Easy™
Steam Mop left
white spot on the
floor.
Do you have hard water? If you do, you might want to
switch to distilled water.
Make sure the water is securely on the water tank.
The pad might be dirty, change the pad.
If you washed the pocket with powder detergent, then the
pad may have residual detergent left on it. Wash it again
with liquid detergent.
fig. 5
CARE OF YOUR MICRO-FIBER
CLEANING PAD
ORDERING REPLACEMENT PARTS
If you are cleaning in a kitchen area where there might be a
build-up of grease, use a de-greasing agent such as an all-
purpose cleaner or dish soap and paper towels to clean the
area first.
To order additional parts and
accessories, feel free to contact us at
www.sharkclean.com or call
1-800-418-0934.
Floors are cloudy,
streaky or spotty
after steaming.
1
Wash pads in warm water. Wash
separately from other laundry. Only
use liquid detergent (no powder
detergent). Do not use fabric
softeners. Line dry or dry on a low
dryer setting. (fig. 5)
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to
switch to distilled water.
NOTE: Some parts may be available
at your local retailer. Contact customer
service for any other servicing.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if
the leftover cloudiness is removed.
2 If there are loose threads on the
pad carefully cut the threads with
scissors. Do not pull on them or cut
at the base. (fig. 6)
Make sure the steam pad is attached correctly.
Light & Easy™
Steam Mop is hard
to push.
IMPORTANT: The micro-fiber
cleaning pad may be very hot
from the steam. Use caution when
removing. Let the unit cool for 2-3
minutes.
Check to see if the cleaning pad is excessively dirty.
Replace if the pad is too dirty or wet.
10
TOLL FREE: 1-800-418-0934
11
S3250CW_11_IB_ENG_100913.indd 10-11
10-09-13 10:57 AM
English
Notes
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and $ 9.95 to cover the cost of
return shipping and handling must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………............................………............
ADDRESS: ………………………………………………………………………………………………...........................................
S3250CW 11
DATE OF PURCHASE: ………………….........….. MODEL: ……………….....................................................
NAME AND ADDRESS OF STORE: …………………………………...........................………………………………..
12
TOLL FREE: 1-800-418-0934
13
S3250CW_11_IB_ENG_100913.indd 12-13
10-09-13 10:57 AM
|