Seagate Computer Drive ST9808211A User Guide

Product Manual  
®
Momentus 5400.2  
ST9100823A  
ST9808211A  
ST960822A  
ST9408114A  
ST9308110A  
100310040  
Rev. D  
August 2007  
 
Contents  
6.0  
Momentus 5400.2 Product Manual, Rev. D  
i
 
ii  
Momentus 5400.2 Product Manual, Rev. D  
 
iv  
Momentus 5400.2 Product Manual, Rev. D  
 
1.0  
Introduction  
This manual describes the functional, mechanical and interface specifications for the following Seagate®  
Momentus®5400.2 drives:  
• ST9100823A  
• ST960822A  
• ST9808211A  
• ST9408114A  
• ST9308110A  
These drives provide the following key features:  
• 5,400-RPM spindle speed and 8-Mbyte buffer combine for superior performance.  
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.  
• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.  
• Tunneling Magnetoresistive (TMR) recording heads and EPRML technology, which provide the drives with  
increased areal density.  
• State-of-the-art cache and on-the-fly error-correction algorithms.  
• Full-track multiple-sector transfer capability without local processor intervention.  
• 800 Gs nonoperating shock and 250 Gs operating shock.  
• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.  
• The 3D Defense System™, which includes Drive Defense, Data Defense, and Diagnostic Defense, offers the  
industry’s most comprehensive protection for disc drives.  
• Support for S.M.A.R.T. drive monitoring and reporting.  
• Support for Read Multiple and Write Multiple commands.  
• Support for autodetection of master/slave drives that use cable select (CSEL).  
Figure 1. Momentus 5400.2 PATA disc drive  
Momentus 5400.2 Product Manual, Rev. D  
1
 
                                                     
2
Momentus 5400.2 Product Manual, Rev. D  
 
2.0  
Drive specifications  
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal  
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate  
ST9100823A, ST9808211A, ST960822A, ST9408114A, and ST9308110A model drives.  
2.1  
Specification summary  
The specifications listed in this table are for quick reference. For details on specification measurement or  
definition, see the appropriate section of this manual.  
Table 1:  
Specifications  
Drive specification  
ST9100823A ST9808211A ST960822A ST9408114A ST9308110A  
Formatted Gbytes (512 bytes/sector)  
Guaranteed sectors  
100  
80  
60  
40  
30  
195,371,568  
156,301,488  
117,210,240  
78,140,160  
58,605,120  
Bytes per sector  
512  
Physical read/write heads  
Discs  
4
3
2
3
2
2
1
2
1
2
Cache (Mbytes)  
8
Recording density, BPI (bits/inch typical)  
Track density. TPI (tracks/inch typical)  
703,000  
115,000  
86  
2
Areal density (Gbits/inch max)  
Spindle speed (RPM)  
5,400  
Internal data transfer rate OD  
(Mbytes/sec max)  
48.25  
100  
I/O data-transfer rate (Mbytes/sec max)  
ATA data-transfer modes supported  
Height  
PIO modes 0–4; Multiword DMA modes 0–2; Ultra DMA modes 0–5  
9.5 +/-0.2 mm (0.374 +/-.008 inches)  
Width  
69.85 +/-0.25 mm (2.750 +/-0.010 inches)  
Length  
100.2 +/-0.25 mm (3.945 +/-0.010 inches)  
Weight (typical)  
100 grams (0.22 lb)  
Average latency (msec)  
Power-on to ready (sec typical)  
Standby to ready (sec typical)  
Startup current 5V (typical)  
Track-to-track seek time (msec typical)  
Average seek time (msec typical)  
Average seek, read (msec typical)  
Average seek, write (msec typical)  
Full-stroke seek (msec)  
Seek power (typical)  
5.6  
3.5  
3.0  
1.0 amps  
1.0 (read), 1.5 (write)  
12.5  
12.5  
14.5  
22 (typical); 24 (max)  
2.3 watts  
Momentus 5400.2 Product Manual, Rev. D  
3
 
         
Table 1:  
Specifications  
Drive specification  
ST9100823A ST9808211A ST960822A ST9408114A ST9308110A  
Read/write power (typical)  
Idle mode (typical)  
2.05/2.1 watts  
0.99 watts  
Standby mode  
0.2 watts (typical)**  
0.2 watts (typical)**  
5V ± 5%  
Sleep mode  
Voltage tolerance (including noise)  
5° to 55°C (operating)  
–40° to 70°C (nonoperating)  
Ambient temperature  
Temperature gradient  
20°C (operating)  
(°C per hour max, noncondensing)  
30°C (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity (noncondensing)  
Relative humidity gradient  
Wet bulb temperature (°C max)  
Altitude, operating  
30% per hour max  
30°C (operating)  
40°C (nonoperating)  
–304.8 m to 3,048 m (–1000 ft to 10,000 ft)  
–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)  
Altitude, nonoperating  
(below mean sea level, max)  
Shock, operating (Gs max at 2 msec)  
Shock, nonoperating (Gs max at 2 msec)  
Shock, nonoperating (Gs max at 1 msec)  
Shock, nonoperating (Gs max at 0.5 msec)  
250  
800  
900  
400  
Vibration, operating (max displacement may  
apply below 10 hz)  
1.0 Gs (0 to peak, 5–500 Hz)  
5.0 Gs (0 to peak, 10–500 Hz)  
Vibration, nonoperating (max displacement  
may apply below 22 hz)  
Drive acoustics, sound power (bels)  
Idle*  
2.4 (typical)  
2.6 (max)  
2.6 (typical)  
2.8 (max)  
Quiet seek  
2.9 (typical)  
3.1 (max)  
Performance seek  
14  
Nonrecoverable read errors  
1 per 10 bits read  
330,000 power-on hours  
Mean Time Before Failure (MTBF)  
At nominal power, 25°C ambient temperature.  
Max case temperature: 65°C at the case measurement location shown in Figure 4.  
Load/Unload (U/UL) cycles  
25°C, 50% relative humidity  
600,000 software-controlled power on/off cycles  
20,000 hard power on/off cycles  
32°C, 80% relative humidity  
5°C, 80% relative humidity  
5°C, 10% relative humidity  
55°C, 16% relative humidity  
600,000 software-controlled power on/off cycles  
20,000 hard power on/off cycles  
Service life  
Warranty  
5 Years  
5 Years  
*During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
**Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes  
will not contribute to battery power consumption.  
4
Momentus 5400.2 Product Manual, Rev. D  
 
2.2  
Formatted capacity  
Model  
Formatted capacity  
Guaranteed sectors  
195,371,568  
156,301,488  
117,210,240  
78,140,160  
Bytes per sector  
ST9100823A  
ST9808211A  
ST960822A  
ST9408114A  
ST9308110A  
100 Gbytes  
80 Gbytes  
60 Gbytes  
40 Gbytes  
30 Gbytes  
512  
512  
512  
512  
512  
58,605,120  
2.3  
Default logical geometry  
Cylinders  
Read/write heads  
Sectors per track  
16,383  
16  
63  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
2.4  
Physical organization  
Model  
Read/write heads  
Number of discs  
ST9100823A  
ST9808211A  
ST960822A  
ST9408114A  
ST9308110A  
4
3
3
2
2
2
2
2
1
1
Momentus 5400.2 Product Manual, Rev. D  
5
 
                       
2.5  
Recording and interface technology  
Technology  
Specification  
Interface  
Parallel ATA  
Recording method  
RLL 0,11  
Recording density BPI (bits/inch typical)  
Track density TPI (tracks/inch typical)  
703,000  
115,000  
2
Areal density (Gbits/inch max)  
86  
Spindle speed (RPM) (± 0.2%)  
Internal data-transfer rate OD (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
Interleave  
5,400  
48.25  
100 (Ultra DMA mode 5)  
1:1  
Cache buffer  
8 Mbytes (8,192 kbytes)  
2.6  
Physical characteristics  
Height  
(mm)  
(inches)  
9.5 +/–0.2  
0.374 +/–0.008  
Width  
(mm)  
(inches)  
69.85 +/–0.25  
2.750 +/–0.010  
Length  
(mm)  
(inches)  
100.2 +/–0.25  
3.945 +/–0.010  
Typical weight  
(grams)  
(pounds)  
100  
0.22  
6
Momentus 5400.2 Product Manual, Rev. D  
 
                                         
2.7  
Seek time  
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using  
drive diagnostics. The specifications below are defined as follows:  
• Track-to-track seek time is an average of all possible single-track seeks in both directions.  
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between  
random tracks, less overhead.  
Typical seek times (msec)*  
Track-to-track  
Read  
1.0  
Write  
1.5  
Average  
12.5  
22.0  
5.56  
14.5  
24.0  
5.56  
Full-stroke  
Average latency  
*Measured in performance mode  
Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,  
regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.  
However, due to the manner in which these drives are formatted, benchmark tests that include command  
overhead or measure logical seeks may produce results that vary from these specifications.  
2.8  
Time to ready  
Time to ready  
Typical  
3.5  
Max  
8.0  
Power-on to Ready (sec)  
Standby to Ready (sec)  
3.0  
8.0  
Momentus 5400.2 Product Manual, Rev. D  
7
 
                     
2.9  
Power specifications  
The drive receives DC power (+5V) through the interface connector.  
2.9.1 Power consumption  
Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on  
an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient temperature.  
• Spinup power  
Spinup power is measured fromthe time ofpower-onto thetimethat the drive spindle reaches operating speed.  
• Seek mode  
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does  
not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on  
three random seek operations every 100 msecs. This mode is not typical.  
Read/write power and current  
Read/write power is measured with the heads on track, based on three 63 sector read or write operations  
every 100 msecs.  
• Idle mode power*  
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in  
a random track location.  
• Standby mode  
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/  
write electronics are in power-down model  
Table 2:  
DC power  
Power dissipation  
Spinup (typical)  
Idle, performance mode*  
Idle, active*  
Idle, low power mode*  
Seeking  
+5V average (watts, 25° C)  
1.00 amps  
1.85  
0.99  
0.85  
2.3  
Read  
2.05  
2.1  
Write  
Standby  
0.20  
0.20  
Sleep  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
8
Momentus 5400.2 Product Manual, Rev. D  
 
                                     
2.9.1.1  
Typical current profile  
Figure 2. Typical 5V startup and operation current profile  
2.9.2  
Conducted noise  
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on  
the +5 volt line.  
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave  
injected noise at up to 10 MHz.  
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.  
2.9.3  
Voltage tolerance  
Voltage tolerance (including noise):  
5V ± 5%  
Momentus 5400.2 Product Manual, Rev. D  
9
 
                 
2.9.4  
Power-management modes  
The drive provides programmable power management to provide greater energy efficiency. In most systems,  
you can control power management through the system setup program. The drive features the following  
power-management modes:  
Table 3:  
Power management modes  
Power modes  
Active (operating)  
Idle, performance  
Idle, active  
Heads  
Spindle  
Rotating  
Rotating  
Rotating  
Rotating  
Stopped  
Stopped  
Buffer  
Tracking  
Tracking  
Floating  
Parked  
Parked  
Parked  
Enabled  
Enabled  
Disabled  
Disabled  
Disabled  
Disabled  
Idle, low power  
Standby  
Sleep  
• Active mode  
The drive is in Active mode during the read/write and seek operations.  
• Idle mode  
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc  
access is necessary.  
• Standby mode  
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the  
standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a  
specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby  
mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all  
commands and returns to Active mode any time disc access is necessary.  
• Sleep mode  
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer  
is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a  
Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby  
mode with all current translation parameters intact.  
• Idle and Standby timers  
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and  
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive  
activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive  
accepts all commands and returns to Active mode when disc access is necessary.  
10  
Momentus 5400.2 Product Manual, Rev. D  
 
                   
2.10  
Environmental specifications  
Ambient temperature  
2.10.1  
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.  
Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions.  
Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.  
Operating  
5° to 55°C (41° to 131°F)  
Nonoperating  
–40° to 70°C (–40° to 158°F)  
2.10.2  
Temperature gradient  
Operating  
20°C per hour (68°F per hour max), without condensation  
30°C per hour (86°F per hour max)  
Nonoperating  
2.10.3  
Humidity  
2.10.3.1  
2.10.3.2  
2.10.4  
Relative humidity  
Operating 5% to 90% noncondensing (30% per hour max)  
Nonoperating 5% to 95% noncondensing (30% per hour max)  
Wet bulb temperature  
Operating 30°C (86°F max)  
Nonoperating 40°C (104°F max)  
Altitude  
Operating  
Nonoperating  
–304.8 m to 3,048 m (–1,000 ft to 10,000 ft)  
–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)  
Momentus 5400.2 Product Manual, Rev. D  
11  
 
                             
2.10.5  
Shock  
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive  
mounting screws. Shock may be applied in the X, Y or Z axis.  
2.10.5.1  
Operating shock  
These drives comply with the performance levels specified in this document when subjected to a maximum  
operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more  
than two times per second.  
2.10.5.2  
Nonoperating shock  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse  
of 2 msec duration.  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 900 Gs based on a nonrepetitive half-sine shock pulse  
of 1 msec duration.  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 400 Gs based on a nonrepetitive half-sine shock pulse  
of 0.5 msec duration.  
2.10.6  
Vibration  
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the  
drive mounting screws. Vibration may be applied in the X, Y or Z axis.  
2.10.6.1  
Operating vibration  
The following table lists the maximum vibration levels that the drive may experience while meeting the perfor-  
mance standards specified in this document.  
5–500 Hz 1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.  
2.10.6.2  
Nonoperating vibration  
The following table lists the maximum nonoperating vibration that the drive may experience without incurring  
physical damage or degradation in performance when subsequently put into operation.  
10–500 Hz  
5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.  
12  
Momentus 5400.2 Product Manual, Rev. D  
 
               
2.11  
Acoustics  
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-  
surements are consistent with ISO document 7779. Sound power measurements are taken under essentially  
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.  
Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is  
defined by the following equation:  
(Number of seeks per second = 0.4 / (average latency + average access time)  
Table 4:  
Drive level acoustics  
Acoustic mode  
Idle*  
Quiet Seek  
Performance Seek  
2.4 bels (typ)  
2.6 bels (max)  
2.6 bels (typ)  
2.8 bels (max)  
2.9 bels (typ)  
3.1 bels (max)  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
2.12  
Electromagnetic immunity  
When properly installed in a representative host system, the drive operates without errors or degradation in  
performance when subjected to the rradio frequency (RF) environments defined in the following table:  
Table 5:  
Electromagnetic immunity  
Performance  
level  
Reference  
standard  
Test  
Description  
Electrostatic discharge  
Radiated RF immunity  
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV  
B
A
EN 61000-4-2: 95  
EN 61000-4-3: 96  
80 to 2,000 MHz, 10 V/m,  
80% AM with 1 kHz sine  
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz  
ENV 50204: 95  
Electrical fast transient  
Surge immunity  
± 1 kV on AC mains, ± 0.5 kV on external I/O  
± 1 kV differential, ± 2 kV common, AC mains  
B
B
A
EN 61000-4-4: 95  
EN 61000-4-5: 95  
EN 61000-4-6: 97  
Conducted RF immunity  
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz  
sine  
Power Frequency H-field 1 A/m, 50Hz/60Hz, 3 axes  
immunity  
A
EN 61000-4-8: 97  
EN 61000-4-11: 94  
Voltage dips, interrupts  
30% Reduction for 25 cycles  
>95% Reduction for 250 cycles  
>95%, 0.5 cycles  
C
C
B
A - 1) No upset or degradation in performance beyond manufacturer’s specified limits.  
2) No data loss.  
B - 1) Unit self recovers without user intervention.  
2) No data loss.  
C - 1) Upset OK provided that unit will function after user intervention.  
Momentus 5400.2 Product Manual, Rev. D  
13  
 
                               
2.13  
Reliability  
Measurement type  
Specification  
14  
Nonrecoverable read errors  
1 per 10 bits read, max.  
Mean time between failures  
(MTBF)  
330,000 power-on hours  
At nominal power, 25°C ambient temperature.  
Max case temperature: 65°C at the case measurement location shown in Figure 4.  
Load/Unload (U/UL)  
25°C, 50% relative humidity  
600,000 software-controlled power on/off cycles  
20,000 hard power on/off cycles  
32°C, 80% relative humidity  
5°C, 80% relative humidity  
5°C, 10% relative humidity  
55°C, 16% relative humidity  
600,000 software-controlled power on/off cycles  
20,000 hard power on/off cycles  
Service Life  
Warranty  
5 Years  
5 Years  
2.14  
Agency certification  
Safety certification  
2.14.1  
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections  
of IEC950 and EN 60950 as tested by TUV North America.  
2.14.2  
Electromagnetic compatibility  
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-  
tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product  
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and  
the immunity levels are defined by EN 55024.  
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous  
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply  
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the  
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O  
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators  
should confirm EMC compliance and provide CE marking for their products.  
14  
Momentus 5400.2 Product Manual, Rev. D  
 
                                                           
Korean RRL  
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-  
graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic  
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information  
and Communication Republic of Korea.  
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-  
ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-  
nized lab.  
• EUT name (model numbers): ST9100823A. ST9808211A, ST960822A, ST9408114A, and ST9308110A.  
• Certificate numbers:  
ST9100823A  
ST9808211A  
ST960822A  
ST9408114A  
ST9308110A  
E-D011-04-3510(B)  
E-D011-04-3506(B)  
E-D011-04-3503(B)  
E-D011-04-3502(B)  
E-D011-04-3504(B)  
• Trade name or applicant: Seagate Technology International  
• Manufacturing date: August 2004  
• Manufacturer/nationality: Seagate Technology International  
Australian C-Tick (N176)  
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548  
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-  
cation Authority (ACA).  
2.14.3  
FCC verification  
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached  
as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-  
keted to the customer. As a subassembly, no Federal Communications Commission verification or certification  
of the device is required.  
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total  
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B  
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is  
likely to result in interference to radio and television reception.  
Radio and television interference. This equipment generates and uses radio frequency energy and if not  
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio  
and television reception.  
This equipment is designed to provide reasonable protection against such interference in a residential installa-  
tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause interference to radio or television, which can be determined by turning the equipment on and off,  
you are encouraged to try one or more of the following corrective measures:  
• Reorient the receiving antenna.  
• Move the device to one side or the other of the radio or TV.  
• Move the device farther away from the radio or TV.  
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.  
Momentus 5400.2 Product Manual, Rev. D  
15  
 
                 
If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-  
gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:  
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-  
intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-  
ber 004-000-00345-4.  
2.15  
Environmental protection  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances.  
European Union Restriction of Hazardous Substances (RoHS)  
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical  
substances, including Lead (Pb), in electronic products effective July 2006.  
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the rep-  
resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our  
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document  
their compliance with our requirements by providing material content declarations for all parts and materials for  
the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion  
of any RoHS-regulated substance in such parts or materials.  
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws  
and regulations which restrict chemical content in electronic products. These systems include standard  
operat-ing procedures that ensure that restricted substances are not utilized in our manufacturing operations,  
labora-tory analytical validation testing, and an internal auditing process to ensure that all standard operating  
procedures are complied with.  
16  
Momentus 5400.2 Product Manual, Rev. D  
 
     
3.0  
Configuring and mounting the drive  
This section contains the specifications and instructions for configuring and mounting the drive.  
3.1  
Handling and static discharge precautions  
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-  
charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:  
Caution:  
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s  
exposure to ESD.  
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal  
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire  
installation procedure.  
• Handle the drive only by its edges or frame.  
• The drive is fragile—handle it with care. Do not press down on the drive top cover.  
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.  
• Do not touch the connector pins or the printed circuit board.  
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids  
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are  
used to seal out dirt and contamination.  
3.2  
Jumper settings  
3.2.1  
Master/slave configuration  
Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the  
4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable  
select option, see Section 3.2.2.  
The “Master or single drive” option is the factory default setting.  
Drive is master (or single drive)  
Drive is slave  
Cable select  
Figure 3. Jumper settings  
Momentus 5400.2 Product Manual, Rev. D  
17  
 
                     
3.2.2  
Cable-select option  
Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,  
CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To  
enable cable select, set a jumper as shown in Figure 3. Refer to your computer manual to determine whether  
your computer supports this option.  
3.3  
Drive mounting  
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting  
holes. See Figure 4 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow  
these important mounting precautions when mounting the drive:  
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.  
• Use only M3 x 0.5 mounting screws.  
• Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).  
• Four (4) threads (0.080 inches) minimum screw engagement recommended.  
3.945 +/-0.010  
(100.2 +/-.25)  
0.490 +/- .010  
(12.446 +/- .254)  
.157  
(3.9878)  
.399  
(10.135)  
0.673 +/- .010  
(17.09 +/- .254)  
Breather Hole  
Do not cover  
or seal.  
2.750 +/- .010  
(69.85 +/- .25)  
3.567  
(90.60)  
Recommended case temp.  
measurement location  
.551  
2X M3 X 0.5-6H  
Mounting holes  
Both sides  
(13.99)  
.374 +/- .008  
(9.5 +/- .2)  
.12 min. full thread  
2X .118 (3.00)  
Both sides  
4X M3 X 0.5-6H  
Mounting holes  
.10 min. full thread  
3.567  
(90.60)  
.551  
(13.99)  
inches  
(mm)  
2.430  
(61.72)  
.399  
(10.135)  
.160  
(4.06)  
Detail A  
Detail A  
Figure 4. Mounting dimensions—top, side and end view  
18  
Momentus 5400.2 Product Manual, Rev. D  
 
               
4.0  
ATA interface  
These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports  
ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The  
drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.  
For detailed information about the ATA interface, refer to the draft of AT Attachment with Packet Interface  
Extension (ATA/ATAPI-6), NCITS T13 1410D, subsequently referred to as the Draft ATA-6 Standard.  
4.1  
ATA interface signals and connector pins  
The following table summarizes the signals on the 44-pin ATA interface connector. For a detailed description of  
these signals, refer to the Draft ATA-6 Standard.  
Table 6:  
Connector signals  
Connector  
Contact  
Cable  
Conductor  
Cable  
Conductor  
Connector  
Contact  
Signal Name  
Signal Name  
RESET-  
DD7  
1
1
2
2
Ground  
DD8  
3
3
4
4
DD6  
5
5
6
6
DD9  
DD5  
7
7
8
8
DD10  
DD4  
9
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
DD11  
DD3  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
43  
DD12  
DD2  
DD13  
DD1  
DD14  
DD0  
DD15  
Ground  
DMARQ  
DIOW-  
DIOR-  
IORDY  
DMACK-  
INTRQ  
DA1  
(keypin)  
Ground  
Ground  
Ground  
PSYNC:CSEL  
Ground  
IOCS16-  
PDIAG-  
DA2  
DA0  
CS1FX-  
DASP-  
+5 V (Logic)  
CS3FX-  
Ground  
+5V (Motor)  
No connection  
Ground (Return)  
43  
Momentus 5400.2 Product Manual, Rev. D  
19  
 
                   
4.1.1  
Supported ATA commands  
The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA  
commands, refer to the Draft ATA-6 Standard...  
Table 7:  
Supported commands  
Command name  
Command code (in hex)  
ATA-standard commands  
ATA Device Configuration Overlay  
ATA Service  
B1  
A2  
H
H
Check Power Mode  
Download Microcode  
Execute Device Diagnostics  
Flush Cache  
98 E5  
H,  
H
92  
90  
H
H
E7  
H
Flush Cache Extended  
Format Track (Legacy)  
Identify Device  
EA  
H
50  
H
EC  
H
Idle  
97 E3  
H,  
H
Idle Immediate  
95 E1  
H,  
H
Initialize Device Parameters  
Read Buffer  
91  
H
E4  
H
Read DMA  
C8 C9  
H,  
H
Read DMA Extended  
Read Log Extended  
Read Multiple  
25  
22  
H
H
C4  
H
Read Multiple Extended  
Read Native Max Address  
Read Native Max Address Extended  
Read Sectors  
29  
H
F8  
H
H
27  
20 21  
H,  
H
Read Sectors Extended  
Read Verify Sectors  
Read Verify Sectors Extended  
Recalibrate  
24  
H
40 41  
H,  
H
42  
10  
H
H
Security Disable Password  
Security Erase Prepare  
Security Erase Unit  
Security Freeze Lock  
Security Set Password  
F6  
F3  
F4  
F5  
F1  
H
H
H
H
H
20  
Momentus 5400.2 Product Manual, Rev. D  
 
                                         
Table 7:  
Supported commands  
Command name  
Security Unlock  
Seek  
Command code (in hex)  
F2  
H
H
H
70  
91  
Set Drive Parameters  
Set Features  
EF  
H
Set Max Address  
Note: Individual Set Max com-  
F9  
H
Address  
00  
01  
02  
03  
H
H
H
H
H
mands are identified by the value Password  
placed in the Set Max Features  
register as defined to the right.  
Lock  
Unlock  
Freeze Lock 04  
Set Multiple Mode  
Sleep  
C6  
H
99 E6  
H,  
H
S.M.A.R.T.  
B0  
H
Standby  
96 E2  
H, H  
Standby Immediate  
Vendor Unique  
Write Buffer  
94 E0  
H, H  
9A FA FB  
H,  
H
H,  
H
E8  
Write DMA  
CA CB  
H, H  
Write DMA Extended  
Write Log Extended  
Write Multiple  
35  
32  
H
H
C5  
H
Write Multiple Extended  
Write Sectors  
39  
H
30 31  
H,  
H
Write Sectors Extended  
34  
H
ATA-standard power-management commands  
Check Power Mode  
Idle  
98 or E5  
H
H
H
H
H
H
H
97 or E3  
H
Idle Immediate  
95 or E1  
H
Sleep  
99 or E6  
H
Standby  
96 or E2  
H
Standby Immediate  
ATA-standard security commands  
Security Set Password  
Security Unlock  
Security Erase Prepare  
Security Erase Unit  
94 or E0  
H
F1  
F2  
F3  
F4  
H
H
H
H
Momentus 5400.2 Product Manual, Rev. D  
21  
 
                                               
Table 7:  
Supported commands  
Command name  
Command code (in hex)  
Security Freeze Lock  
Security Disable Password  
F5  
F6  
H
H
22  
Momentus 5400.2 Product Manual, Rev. D  
 
   
4.1.2  
Identify Device command  
The Identify Device command (command code EC ) transfers information about the drive to the host following  
H
power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 7 on  
page 20. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or  
vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.  
Thefollowingcommandscontaindrive-specificfeaturesthatmaynotbeincludedintheDraftATA-6Standard.  
Word  
Description  
Value  
0C5A  
0
Configuration information:  
• Bit 15: 0 = ATA; 1 = ATAPI  
• Bit 7: removable media  
• Bit 6: removable controller  
• Bit 0: reserved  
H
1
Number of logical cylinders  
16,383  
2
ATA-reserved  
0000  
16  
H
3
Number of logical heads  
4
Retired  
0000  
H
H
5
Retired  
0000  
6
Number of logical sectors per logical track: 63  
Retired  
003F  
H
7–9  
10–19  
20  
0000  
H
Serial number: (20 ASCII characters, 0000 = none)  
ASCII  
H
Retired  
Retired  
Obsolete  
0000  
0400  
0000  
x.xx  
H
H
H
21  
22  
23–26  
Firmware revision  
(8 ASCII character string, padded with blanks to end of string)  
27–46  
47  
Drive model number (40 ASCII characters, padded with blanks  
to end of string)  
ST9100823A  
ST9808211A  
ST960822A  
ST9408114A  
ST9308110A  
(Bits 7–0) Maximum sectors per interrupt on Read multiple and  
Write multiple (16)  
8010  
H
48  
Reserved  
0000  
H
49  
Standard Standby timer, IORDY supported and may be disabled  
ATA-reserved  
2F00  
H
H
H
H
H
50  
0000  
0200  
0200  
0007  
51  
PIO data-transfer cycle timing mode  
Retired  
52  
53  
Words 54–58, 64–70 and 88 are valid  
Number of current logical cylinders  
Number of current logical heads  
Number of current logical sectors per logical track  
Current capacity in sectors  
54  
xxxx  
xxxx  
xxxx  
xxxx  
H
55  
H
H
H
56  
57–58  
Momentus 5400.2 Product Manual, Rev. D  
23  
 
   
Word  
Description  
Value  
xxxx  
59  
Number of sectors transferred during a Read Multiple or Write  
Multiple command  
H
60–61  
Total number of user-addressable LBA sectors available  
(see Section 2.2 for related information)  
ST9100823A = 195,371,568  
ST9808211A = 156,301,488  
ST960822A = 117,210,240  
ST9408114A = 78,140,160  
ST9308110A = 58,605,120  
62  
63  
Retired  
0000  
H
H
Multiword DMA active and modes supported (see note following  
this table)  
xx07  
64  
65  
Advanced PIO modes supported (modes 3 and 4 supported)  
0003  
0078  
H
Minimum multiword DMA transfer cycle time per word (120  
nsec)  
H
66  
Recommended multiword DMA transfer cycle time per word  
(120 nsec)  
0078  
H
67  
Minimum PIO cycle time without IORDY flow control (240 nsec)  
Minimum PIO cycle time with IORDY flow control (120 nsec)  
ATA-reserved  
00F0  
H
H
H
H
H
68  
0078  
0000  
0000  
0000  
69–74  
75  
Queue depth  
76–79  
80  
ATA-reserved  
Major version number  
007E  
H
H
81  
Minor version number  
0000  
82  
Command sets supported  
346B  
H
83  
Command sets supported  
7D01  
H
84  
Command sets support extension  
Command sets enabled  
4003  
H
85  
34xx  
H
H
86  
Command sets enabled  
3xxx  
87  
Command sets enable extension  
4003  
H
88  
Ultra DMA support and current mode  
(see note following this table)  
xx3F  
H
89  
Security erase time  
0000  
0000  
0040  
H
H
H
90  
Enhanced security erase time  
Advanced power management value  
Master password revision code  
Hardware reset value (see description following this table)  
Auto acoustic management setting  
ATA-reserved  
91  
92  
FFFE  
H
93  
xxxx  
xxxx  
H
94  
H
95–127  
128  
129–159  
0000  
0001  
H
Security status  
H
Seagate-reserved  
xxxx  
H
24  
Momentus 5400.2 Product Manual, Rev. D  
 
Word  
160–254  
255  
Description  
ATA-reserved  
Integrity word  
Value  
0000  
xxA5  
H
H
Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data.  
Description (if bit is set to 1)  
Bit  
0
Word 63  
Multiword DMA mode 0 is supported.  
Multiword DMA mode 1 is supported.  
Multiword DMA mode 2 is supported.  
Multiword DMA mode 0 is currently active.  
Multiword DMA mode 1 is currently active.  
Multiword DMA mode 2 is currently active.  
1
2
8
9
10  
Bit  
0
Word 88  
Ultra DMA mode 0 is supported.  
Ultra DMA mode 1 is supported.  
Ultra DMA mode 2 is supported.  
Ultra DMA mode 3 is supported.  
Ultra DMA mode 4 is supported.  
Ultra DMA mode 0 is currently active.  
Ultra DMA mode 1 is currently active.  
Ultra DMA mode 2 is currently active.  
Ultra DMA mode 3 is currently active.  
Ultra DMA mode 4 is currently active.  
Ultra DMA mode 5 is currently active.  
1
2
3
4
8
9
10  
11  
12  
13  
Bit  
Word 93  
13  
1 = 80-conductor cable detected, CBLID above VIH  
0 = 40-conductor cable detected, CBLID below VIL  
Momentus 5400.2 Product Manual, Rev. D  
25  
 
4.1.3  
Set Features command  
This command controls the implementation of various features that the drive supports. When the drive receives  
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-  
rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.  
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the  
Features register are defined as follows:  
Table 8:  
Features register values  
02  
03  
Enable write cache (default).  
H
Set transfer mode (based on value in Sector Count register).  
H
Sector Count register values:  
00  
01  
08  
09  
Set PIO mode to default (PIO mode 2).  
Set PIO mode to default and disable IORDY (PIO mode 2).  
PIO mode 0  
H
H
H
H
PIO mode 1  
0A  
PIO mode 2  
H
0B  
PIO mode 3  
H
0C  
PIO mode 4 (default)  
Multiword DMA mode 0  
Multiword DMA mode 1  
Multiword DMA mode 2  
Ultra DMA mode 0  
H
20  
21  
22  
40  
41  
42  
43  
44  
45  
H
H
H
H
H
H
H
H
H
Ultra DMA mode 1  
Ultra DMA mode 2  
Ultra DMA mode 3  
Ultra DMA mode 4  
Ultra DMA mode 5  
05  
55  
82  
Enable advanced power management  
Disable read look-ahead (read cache) feature.  
Disable write cache.  
H
H
H
AA  
Enable read look-ahead (read cache) feature (default).  
Report full capacity available  
H
F1  
H
Note. At power-on or after a hardware or software reset the default values of the features are as indicated  
above.  
26  
Momentus 5400.2 Product Manual, Rev. D  
 
       
5.0  
Compatibility summary  
5.1  
Installation considerations  
Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard  
drive. Refer to your system’s user manual for the location of the hard drive compartment and the specific  
instructions regarding replacement. Refer to your system manufacturer’s support website for the most up-to-  
date information. Read and follow all instructions regarding the proper steps to be taken when replacing the  
system hard drive. Some mobile systems are sealed and require specialized tools to gain access to the hard  
drive. Special training or tools may be needed to service some mobile computers. In some cases, opening the  
case may void your warranty. Consult your system documentation. Seagate recommends taking your system  
to an authorized service technician to replace your hard drive.  
Momentus 5400.2 Product Manual, Rev. D  
27  
 
     
System Compatibility  
Seagate Product Assurance has tested Momentus drives in the systems listed in Table 9. Testing included mul-  
tiple BIOS versions and operating systems. This testing was done to demonstrate compatibility with various  
hardware and software configurations. Hardware and software combinations, other than those tested, may  
also be compatible with this drive.  
Table 9:  
Tested systems  
Gateway 300SE  
Gateway 450RGH  
Gateway 500XL  
Gateway 700S  
Gateway 700X  
ABIT BL7  
Acer Aspire 2000  
Amilio  
ASUS P4SGL-VM  
AZZA P4X2-AV  
Bonatti  
EVO D300  
EVO D300V  
EVO D310  
EVO D310M  
EVO D310V  
EVO D500  
EVO D500M  
EVO D500S  
Lavie LJ700/7E  
Lavie LL750/8  
Lavie LL970/9D  
Lavie LR700/9E  
Lavie LS830/9D  
Microstar MSI-6561  
Microstar MSI-6566E  
Millennia 920I PRO  
MIM 2020  
Micron T2000  
Micron T2100  
Micron T2200  
Thinkpad  
Thinkpad A22E  
ThinkpadG40  
Thinkpad T30  
Thinkpad T40  
Tian YI S180  
EVO D510  
EVO D510 SFF  
EVO D510C  
MIT-RHE-BT  
Netvista  
Transport GX3  
Transport T1000  
Transport V1000  
Travel Mate 660  
Travel Mate 800LCI  
Travel Mate 800LCI  
Travel Mate 2500  
Travel Mate 290VCI  
Travel Mate 650  
Travel Mate 660  
Travel Mate 800  
Travel Mate 8000  
Trigem S7 7570  
Trigem V7 7600  
NECUNI-TRI-NT  
Micron V2000  
Vaio PCG-V505/B  
Vaio PCG-ZIR/P  
Vaio PCV RX770  
Vaio PCV7753  
Vaio PCV-7753  
Valuestar VC300/4D  
Valuestar VF500/8D  
Valuestar VF500/D  
Valuestar VG17H/8  
Valuestar VG17H2Z38  
Valuestar VT500/4D  
Veriton 7200D  
Brasilia  
EVO E-6000  
EVO N620C  
EVO W-4000  
FID 2040  
FID 2100  
FMV 16C/V  
Optiplex GX150  
Optiplex GX260  
Optiplex GX400  
Pavillion 774Y  
Pavillion ZD7000  
Pavillion ZT3000  
Pavillion ZV5000  
Pavillion ZX5000  
Sony PCV-RZ60  
Performance  
Client Pro 345  
Client Pro 345E  
Compaq NX9500  
Compaq D315  
HP D330  
HP D330 MT  
HP D330 UT  
HP D530  
FMV Biblo MG 75HT/ST  
FMV Biblo NB75H/T  
FMV Biblo NH90H/T  
FMV CE50G7 (IVY6)  
FMV NB18C  
Gigabyte GA-7DXR+  
Gigabyte GA-8IDX  
Gigabyte GA-8SIML  
Gigabyte GA-8SR533  
HP/Compaq NX7000  
IBM XNote  
Imedia 7150(Discovery)  
Inspirion 8100  
Inspirion 1150  
Inspirion 2650  
Inspirion 300M  
Inspirion 5100  
Inspirion 5150  
Inspirion 600M  
Inspirion 8600  
Inspirion 9100  
Inspirion XPS  
Intel 845GBV  
Intel SPRINGDALE-G  
Intellistation EPVO  
Intellistation M PRO  
JIA HE H150  
Latitude 100L  
Latitude 8600  
Latitude D400  
Latitude D505  
Latitude D600  
Latitude D800  
Latitude X300  
HP D530 CMT  
HP D530 SFF  
HP D530 USDT  
Dimensio GX400  
Dimension 4100  
Dimension 4100 XPSZ  
Dimension 4400  
Dimension 4500S  
Dimension 4600  
Dimension 8100  
Dimension 8200  
Dimension 8250  
Dimension 8300  
Dimension XPS  
Dynabook TX/2513CMCW  
Compaq E -6000  
Gateway E Series  
Gateway E-2000  
Gateway E-4000  
Gateway E-4100  
Gateway E4600  
Gateway E6000  
Gateway E-6100  
Elite ECS-K7S6A  
Elite ECS-L4S5MG  
Elite K7S5A  
Performance 1400  
Performance 1500  
Powerbook 5  
Powerbook 5,2  
Powerbook 5,2  
Powerbook G4  
Precision 330  
Precision 340  
Precision 350  
Precision 360  
Precision 530  
Precision M60  
Presario 2100  
Presario 2500  
Presario 6000  
Presario 8000  
Presario 8000Z  
Presario R3000  
Presario X1000  
Pro S P4-1300SE  
Pro S P4-1400  
Qosmio E10/1JCDT  
IBM R50  
Veriton 7500  
VGN-A70P  
W 6000  
Workstation XW5000  
Workstation XW8000  
Presario X1000  
MPC X3000  
IBM R50P  
SB-4100A  
SB-4100-C  
SB-4100-E  
SB-4100-B  
Shuttle AV40  
Slotek SL-85SD  
Scnic  
Yi He A760D  
Zhao Yang E260  
Zhao Yang E600A  
Zhao Yang S620  
Equium 3140CS  
Equium 3150  
Equium 5070CS  
ES2 300X  
ES2 500S  
ESX- SB-400 E PC  
ESX500S  
28  
Momentus 5400.2 Product Manual, Rev. D  
 
   
5.2  
BIOS versions tested  
The following list indicates the types of BIOS Seagate tested during the compatibility testing process. The list  
highlights the major BIOS manufacturers. Individual systems contain variations of these BIOS versions and  
were tested with regard to their implementation in the individual systems.  
Table 10:  
Tested BIOS versions  
Release  
Vendor  
ACER  
ACPI  
Revision  
1.01  
Ver. 1.20  
Various  
AMI  
Various  
4.71F1  
4.8.4F1  
Various  
38118  
68xxx  
Apple  
Apple  
Award  
Compal  
Compaq  
Compaq  
Compaq  
Compaq  
Dell  
Various  
v2.00  
Various  
Various  
v1.08  
78xxx  
8602  
F.07  
Various  
Various  
Various  
Various  
A03  
Gateway  
HP  
Various  
Various  
1.1  
IBM  
Insyde SCU  
Insyde  
Insyde  
Intel  
Various  
Mobilepro  
786B2  
Various  
Various  
v1.11  
M1300  
Medion  
Micron  
Mobile Pro  
NEC  
A02  
37763  
1.0D-1373-0812  
Various  
4.00.01  
Various  
Various  
Various  
V1.04 EC1.01M  
Various  
Phoenix  
Toshiba  
Various  
Various  
Momentus 5400.2 Product Manual, Rev. D  
29  
 
   
5.3  
Operating system versions tested  
This list indicates the types of Operating Systems Seagate tested during the compatibility testing process and  
highlights the major OS manufacturers. Several variations of the major operating systems have been tested.  
Table 11:  
Operating systems tested  
Manufacturer  
Apple  
Version/Release  
MacOS 9.22  
Apple  
MacOS X 10.2.3  
Microsoft  
Microsoft  
Microsoft  
Microsoft  
Microsoft  
MSDOS 6.22  
Windows 98, 98SE, ME (multiple languages)  
Windows 2000, 2000-Pro (+SP 1 thru 4) (multiple languages)  
Windows NT 4.0 (+SP 6 and 6a) (+Japanese)  
Windows XP, XP Pro, XP Home (+SP1) (multiple languages)  
5.4  
Compatibility test configurations  
The Momentus drives have been tested to demonstrate compliance with ATA/ATAPI-6 in both the master drive  
and slave drive positions. These tests were preformed to ensure the functionality to ATA/ATAPI-6 specifications  
and the compatibility of Seagate Momentus drives with other ATA/ATAPI-6 compliant peripherals.  
5.5  
Software utilities  
The following is a brief overview of a some of the Seagate utilities used during the Seagate competitive analy-  
sis process.  
The Seagate SeaTools application is an exclusive disc drive diagnostic software designed to troubleshoot most  
hard drive issues. Desktop edition works with most ATA, SATA, or SCSI drives in desktop systems and has a  
98 percent accuracy rate.  
The Seagate DiscWizard™ application simplifies the installation of disc drives. This software also overcomes  
many system BIOS and operating system limitations that can complicate the installation of higher-capacity ATA  
(IDE) interface drives.  
This is a list of some of the third party utilities used in the testing process.  
Vendor  
AMI  
Application  
Diagnostic  
Apple  
Macbench  
Intel  
PCI-EXE  
Microsoft  
Symantec  
Winbench99  
Norton Utilities  
5.6  
Other certification  
Microsoft software compatibility.  
30  
Momentus 5400.2 Product Manual, Rev. D  
 
                   
6.0  
Seagate Technology support services  
Internet  
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is  
available 24 hours daily by email for your questions.  
Presales Support:  
Technical Support:  
Warranty Support:  
mySeagate  
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides  
self-service access to critical applications, personalized content and the tools that allow our partners to  
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,  
password-protected Web interface-anytime, anywhere in the world.  
spp.seagate.com  
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You  
may register for customized communications that are not available on the web. These communications contain  
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the  
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.  
Seagate Service Centers  
Presales Support  
Our Presales Support staff can help you determine which Seagate products are best suited for your specific  
application or computer system, as well as product availability and compatibility.  
Technical Support  
Seagate technical support is available to assist you online at support.seagate.com or through one of our call  
centers. Have your system configuration information and your “ST” model number available.  
SeaTDD(+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or  
comments 24 hours daily and exchange messages with a technical support specialist during normal business  
hours for the call center in your region.  
Momentus 5400.2 Product Manual, Rev. D  
31  
 
   
Customer Service Operations  
Warranty Service  
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct  
customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-  
related issues. Resellers or end users of drive products should contact their place of purchase or Seagate  
warranty service for assistance. Have your serial number and model or part number available.  
Data Recovery Services  
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery  
services labs are currently located throughout the world. . Additional information, including an online request  
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx  
Authorized Service Centers  
Seagate Service Centers are available on a global basis for the return of defective products. Contact your  
customer support representative for the location nearest you.  
USA/Canada/Latin America support services  
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/  
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.  
Global Customer Support  
Presales, Technical, and Warranty Support  
Call Center  
USA, Canada,  
and Mexico  
Toll-free  
Direct dial  
1-800-SEAGATE  
+1-405-324-4700  
Data Recovery Services  
Call Center  
Toll-free  
Direct dial  
FAX  
USA, Canada,  
and Mexico  
1-800-475-01435  
+1-905-474-2162  
1-800-475-0158  
+1-905-474-2459  
Europe, the Middle East and Africa Support Services  
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the  
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.  
Asia/Pacific Support Services  
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,  
go to the "Contact Us" page on www.seagate.com.  
32  
Momentus 5400.2 Product Manual, Rev. D  
 
demonstrate compliance 30  
density 6  
Index  
Diagnostic Defense 1  
diagnostic software 1  
discs 5  
Numerics  
3D Defense System 1  
dissipation 8  
Download Microcode 20  
Drive Defense 1  
drive diagnostics 7  
drive monitoring 1  
drive self-test 1  
A
acoustics 13  
Active mode 10  
agency certification (regulatory) 14  
altitude 11  
ambient conditions 3  
ambient temperature 7, 11  
areal density 1, 6  
ATA interface 19  
ATA-standard commands 20  
Australian C-Tick 15  
autodetection 1  
E
electrical fast transient 13  
electromagnetic compatibility 14  
Electromagnetic Compatibility Directive 14  
electromagnetic immunity 13  
electrostatic discharge 13  
EMC compliance 14  
average seek time 7  
EN 60950 14  
enclosures 15  
environmental specifications 11  
EPRML 1  
error-correction algorithms 1  
errors 14  
European Union 14  
B
BIOS manufacturers 29  
BPI 6  
buffer 1, 6  
burst 1  
European Union Restriction of Hazardous Substanc-  
Execute Device Diagnostics 20  
C
cable select 1  
cable-select option 18  
cache 1, 6  
F
case temperature 11  
CE mark 14  
FCC verification 15  
Features register 26  
Flush Cache 20  
Flush Cache Extended 20  
formatted capacity 5  
frequency 13  
certification 14  
Check Power Mode 21  
commands 20  
compatibility 28  
compatibility summary 27  
compatibility test configurations 30  
compliance 14  
conducted noise 9  
conducted RF immunity 13  
configuring the drive 17  
connector pins 19  
CSA C22.2 (950) 14  
CSEL 18  
G
guaranteed sectors 5  
H
handling 17  
heads 1, 5  
height 6  
C-Tick 15  
current profile 9  
humidity 11  
cycles 14  
I
I/O data-transfer rate 6  
Identify Device 20  
Identify Device command 23  
Idle 8, 21  
Idle and Standby timers 10  
D
Data Defense 1  
data-transfer rates 1  
DC power 8  
Momentus 5400.2 Product Manual, Rev. D  
33  
 
Idle Immediate 21  
pins 19  
Idle mode 10  
PIO 19  
Idle mode power 8  
IEC950 14  
power consumption 8  
power dissipation 8  
Information Technology Equipment 14  
Initialize Device Parameters 20  
interface 6, 19  
power frequency h-field immunity 13  
power management 10  
power on/off cycles 14  
power specifications 8  
power-management commands 21  
power-management modes 10  
Power-on to Ready 7  
precautions 18  
interface signals 19  
interference 15  
interleave 6  
internal data-transfer rate OD 6  
ISO document 7779 13  
programmable power management 10  
J
R
jumper settings 17  
radiated RF immunity 13  
radio and television interference 15  
radio frequency (RF) 13  
random track location 8  
Read Buffer 20  
K
Korean RRL 15  
L
Read DMA 20  
LBA mode 5  
length 6  
Read DMA Extended 20  
read errors 14  
Load/Unload 14  
logical geometry 5  
Read Multiple 1, 20  
Read Multiple Extended 20  
Read Native Max Address 20  
Read Native Max Address Extended 20  
Read Sectors 20  
Read Sectors Extended 20  
Read Verify Sectors 20  
Read Verify Sectors Extended 20  
read/write heads 5  
M
master/slave 1  
Master/slave configuration 17  
maximum temperature 11  
Mean time between failures 14  
modes 19  
monitoring 1  
mounting the drive 17, 18  
MTBF 14  
read/write power and current 8  
recording and interface technology 6  
recording density 6  
recording heads 1  
recording method 6  
register 26  
N
noise 9  
relative humidity 11  
nominal power 3  
reliability 14  
nonoperating shock 12  
nonoperating vibration 12  
nonrecoverable read errors 14  
resistance 9  
RoHS 16  
O
S
operating shock 12  
operating system 28  
operating vibration 12  
OS manufacturers 30  
other certification 30  
S.M.A.R.T. 21  
S.M.A.R.T. drive monitoring 1  
safety certification 14  
screws 18  
SeaTools 1  
sectors 5  
security commands 21  
Security Disable Password 22  
Security Erase Prepare 21  
P
physical characteristics 6  
physical organization 5  
34  
Momentus 5400.2 Product Manual, Rev. D  
 
Security Erase Unit 21  
Security Freeze Lock 22  
Security Set Password 21  
Security Unlock 21  
Seek 21  
seek mode 8  
seek time 7  
Seeking 8  
Service Life 14  
servo electronics 8  
Set Features 21  
Set Features command 26  
Set Max 21  
W
Warranty 14  
weight 6  
wet bulb temperature 11  
width 6  
Write Buffer 21  
Write DMA 21  
Write DMA Extended 21  
Write Multiple 1, 21  
Write Multiple Extended 21  
Write Sectors 21  
Write Sectors Extended 21  
Set Multiple Mode 21  
shock 12  
signals 19  
single-track seeks 7  
Sleep 8, 21  
Sleep mode 10  
software utilities 30  
sound 13  
specifications 3  
spindle speed 6  
Spinup 8  
spinup power 8  
Standby 8, 21  
Standby Immediate 21  
Standby mode 8, 10  
Standby to Ready 7  
static-discharge precautions 17  
subassembly 15  
support services 31  
surge immunity 13  
T
technical support services 31  
temperature 11  
temperature gradient 11  
third party utilities 30  
time to ready 7  
timers 10  
TMR 1  
track density 6  
track-to-track seek time 7  
TUV North America 14  
U
UL 1950 14  
V
vibration 12  
voltage 9  
voltage dips, interrupts 13  
voltage tolerance 9  
Momentus 5400.2 Product Manual, Rev. D  
35  
 
36  
Momentus 5400.2 Product Manual, Rev. D  
 
 
Seagate Technology LLC  
920 Disc Drive, Scotts Valley, California 95066-4544, USA  
Publication Number: 100310040, Rev. D, Printed in U.S.A.  
 

RCA Car Stereo System RS2654 User Guide
Rival Fryer S16SG CN User Guide
Roberts Radio Stereo System CD9912 User Guide
RocketFish TV Video Accessories RF TVMLPT01 User Guide
Sakar Camcorder 32490 User Guide
Samsung Cell Phone SPH M570 User Guide
Samsung CRT Television WS 32Z308T User Guide
Samsung DVD Player HDR SR10 User Guide
Sanus Systems Indoor Furnishings VMA201 User Guide
Sanyo Battery Charger CP 2400SCR User Guide