Scag Power Equipment Lawn Mower 7630001 User Guide

MODEL TS  
ACCESSORY FOR:  
STT - ALL MODELS  
STC - MODELS ABOVE SERIAL NUMBER 7630001  
THIS MANUAL CONTAINS THE OPERATING  
INSTRUCTIONS AND SAFETY INFORMATION  
FORYOUR SCAGACCESSORY. READING THIS  
MANUAL WILL PROVIDE YOU WITH MAIN-  
TENANCE AND ADJUSTMENT PROCEDURES  
TO KEEP YOUR ACCESSORY PERFORMING  
TO MAXIMUM EFFICIENCY. THE SPECIFIC  
MODELS THAT THIS BOOK COVERS ARE CON-  
TAINED ON THE INSIDE COVER. BEFORE  
OPERATING YOUR MACHINE, PLEASE READ  
ALL THE INFORMATION ENCLOSED.  
© 2003  
SCAG POWER EQUIPMENT  
DIVISION OF METALCRAFT OF MAYVILLE, INC  
WWW.SCAG.COM  
PART NO. 03142  
PRINTED 8-2003  
PRINTED IN USA  
 
2.1 SAFETY INFORMATION  
1.1 INTRODUCTION  
-NOTE-  
This manual has been prepared to provide the  
information you need to correctly assemble, operate,  
and maintain this Tiger Striper. Read it carefully and  
keep it for future reference.  
To avoid personal injury, it is imperative that all  
safety instructions be observed.  
1. Read this operator's manual and the  
operator's manual that is supplied with the  
machine this attachment is used on.  
The replacement of any part on this product by other  
than the manufacturer's authorized replacement part  
may adversely affect the performance, durability or  
safety of this product.  
A replacement manual is available from your  
authorized Scag Service Dealer or by contacting:  
Scag Power Equipment, Service Department at P.O.  
Box 152, Mayville, WI 53050. You may also contact  
indicate the complete model number of your Scag  
product when ordering a replacement manual.  
USE OF OTHER THAN ORIGINAL SCAG  
REPLACEMENT PARTS WILL VOID THE  
WARRANTY.  
If additional information or service is needed that is  
not outlined in this manual, please contact your Scag  
Power Equipment dealer. Scag dealers are trained in  
the latest service methods and carry a full line of Scag  
replacement parts.  
2. Before removing the Tiger Striper, disengage the  
mower, stop the engine and wait for all  
movement to stop.  
3. ALWAYS turn the engine OFF, remove the key  
and wait for all movement to stop before  
When ordering parts, always provide the complete  
model of this Tiger Striper.  
servicing, cleaning or removing the Tiger Striper.  
All information provided in this manual is based upon  
information available at the time of printing. Scag  
Power Equipment reserves the right to make changes  
at any time without notice or obligation.  
4. Do not modify or alter any component of the  
Tiger Striper attachment or mower.  
5. Do not allow any passengers to ride on the  
mower.  
1.2 DIRECTION REFERENCE  
The "Right" and "Left", "Front" and "Rear" of the  
machine are referenced from the normal operating  
position.  
2.2OPERATINGINSTRUCTIONS  
To operate the Tiger Striper, you will need to lower  
the roller to the operating position. The Tiger Striper  
can be easily removed or locked in the transport  
position whenever the machine is being transported  
or when striping is not needed.  
1. To unlock the Tiger Striper from the transport  
position, lift up slightly on the handle and turn the  
lock pin until the small roll pin lines up with the  
slot. See Figure 2-1 on page 2.  
1
 
3. Repeat on opposite side.  
Roll Pin  
4. Once the Tiger Striper is locked in the transport  
position, remove the ring pins securing the Tiger  
Striper to the mounting brackets. See Figure 2-3  
Lift Up on  
Handle  
Push and Turn Pin to line  
up Roll Pin with Slot  
to Unlock  
FIGURE 2-1  
3. Repeat this procedure on the opposite side.  
The machine is now ready to operate.  
Remove Ring Pins  
2.3 REMOVING THE TIGER STRIPPER  
FIGURE 2-3  
The Tiger Striper can be easily removed whenever  
the machine is being transported or when stripping is  
not needed. To remove the Tiger Striper, follow the  
instructionsbelow.  
5. Slide the Tiger Striper off of the mounting  
brackets.  
6. To install the Tiger Striper, slide the assembly on  
to the mounting brackets and reinstall the ring  
pins. Once the Tiger Striper has been reinstalled,  
follow Section 2.2 Operating Instructions for  
proper operation.  
1. Prepare the machine so there is easy and safe access  
to the work area. Remove the key and maintain all  
safety related work procedures. Always wear eye and  
hand protection.  
2. Lock the Tiger Striper up in the transport position by  
lifting upward on the handle, push and turn the lock  
pin 90 degrees. The small roll pin must be out of the  
slot in the bracket to lock in the transport position.  
SeeFigure2-2.  
3.1 ASSEMBLY INSTRUCTIONS - STT  
-NOTE-  
Use the illustrated parts list as a part  
number reference when following the  
assembly instructions.  
Roll Pin  
1. Remove all packaging materials. Lay out the  
mounting hardware and the Tiger Striper assembly for  
easy access.  
Push and  
Turn Pin to  
Lock  
2. Prepare the machine so there is easy and safe access  
to the work area. Remove the key and maintain all  
safety related work procedures. Always wear eye and  
hand protection.  
FIGURE 2-2  
2
 
3. Attach the mounting brackets to the cross bar  
between the wheel motor brackets using (4) u-  
bolts and (8) serrated flange nuts. See Figure  
3-1. Do not tighten the hardware.  
5. Install the left and right hand Striper Stop  
Brackets (p/n 423953 & p/n 423954) to the  
frame and secure with (4) 3/8-16 x 1" bolts and  
(4) elastic stop nuts. See Figure 3-2.  
(4) 3/8-16 Elastic  
Stop Nut  
-Note-  
423953 L.H.  
Stop Bracket  
If the Tiger Striper is installed on an STT with  
a serial number below 7219999, part  
number 423966 mounting spacer will need to  
be installed between the mounting bracket  
and cross bar. See Figure 3-1.  
(4) 3/8-16 x 1" Bolt  
423954 R.H.  
Stop Bracket  
(4x) U-Bolts  
Mounting  
Bracket  
FIGURE 3-2  
6. Install the Tiger Striper roller assembly to the  
mounting brackets and secure with the ring pins.  
(8x) Serrated Flange  
Nuts  
Mounting  
Bracket  
7. Once the Tiger Striper roller assembly is installed  
and secure, tighten the mounting hardware on  
both mounting brackets.  
STT with a serial number of 7219999 or Below  
8. Follow Section 2.2 Operating Instruction for  
proper operation.  
(4x) U-Bolts  
Mounting  
Spacer  
3.2 ASSEMBLY INSTRUCTIONS - STC  
Mounting  
Bracket  
-NOTE-  
Mounting  
Spacer  
Use the illustrated parts list as a part  
number reference when following the  
assembly instructions.  
Mounting  
Bracket  
(8x) Serrated Flange  
Nuts  
1. Remove all packaging materials. Lay out the  
mounting hardware and the Tiger Striper  
assembly for easy access.  
FIGURE 3-1  
2. Prepare the machine so there is easy and safe  
access to the work area. Remove the key and  
maintain all safety related work procedures.  
Always wear eye and hand protection.  
4. The edge of the mounting bracket should be  
under the wheel motor mounting plate for proper  
installation. See Figure 3-1.  
3
 
3. Attach the mounting brackets to the cross bar  
between the wheel motor brackets using (4) u-  
bolts and (8) serrated flange nuts. See Figure  
3-3. Do not tighten the hardware.  
4.1 LAWN STRIPING  
HOW DOES LAWN STRIPING WORK?  
The “stripe” that you see on the lawn is actually light  
reflecting off the blades of grass. The direction in  
which the grass is bent determines the “light” or  
“dark” stripe. When the blades of grass are bent  
away from you, the grass appears lighter in color  
because light is reflecting off of the length of the  
blade. When the blades of grass are bent towards  
you, the stripe appears darker as you are looking at  
more of the tips of the blades (a smaller reflective  
surface) and the shadows under the blades of grass.  
Cutting a lawn in the up/down, north/south, east/  
west, opposing directions provides the best stripe  
effect.  
-Note-  
The Tiger Striper can not be installed on an  
STC with a serial number below 7630001.  
(4x) U-Bolts  
Mounting  
Spacer  
Mounting  
Bracket  
You may find that certain grasses have a more  
noticeable stripe (stripe easier) than others. Cutting  
the grass at a different height can sometimes change  
the intensity of the stripe. A slightly higher cut  
(example: 3" versus 2.5") can provide more grass to  
be bent over, thus producing a more noticeable  
stripe. In some types of grass, this may have the  
opposite or no effect.  
Mounting  
Spacer  
(8x) Serrated Flange  
Nuts  
Mounting  
Bracket  
Grass that tends to be "stiff" and resists bending will  
not yield a stripe as well as a softer grass that bends  
easily.  
FIGURE 3-3  
Note that you do not need to cut the grass in order to  
stripe it. The roller simply needs to be in the  
unlocked/engaged position. You may find that when  
creating more advanced, overlapping striping  
4. The edge of the mounting bracket should be  
under the wheel motor mounting plate for proper  
installation. See Figure 3-3.  
patterns, you can complete the job faster by applying  
the overlaying stripes without the blades engaged.  
5. Install the Tiger Striper roller assembly to the  
mounting brackets and secure with the ring pins.  
Striping can be used to draw attention to particular  
landscape features. It can be used to further  
enhance the finished, manicured cut that your Scag  
mower delivers.  
6. Once the Tiger Striper roller assembly is installed  
and secure, tighten the mounting hardware on  
both mounting brackets.  
7. Follow Section 2.2 Operating Instruction for  
proper operation.  
4
 
"Checkerboard" pattern:  
LAWN STRIPING GUIDELINES  
A stripe pattern can add richness and depth to any  
lawn. Here are some guidelines to help produce  
various patterns and to enhance your striping  
techniques.  
Begin by mowing the perimeter around the property  
(Reference Figure 4-1). Next, mow in opposing  
directions (North and South or East and West)  
through the remaining portion of the property (as  
shown in Figure 4-1). Take care when turning at the  
end of each row to prevent turf damage. A simple  
"Y" type turn at the end of each row will reduce the  
chance of turf damage while setting the mower up  
for the next row to be mowed.  
Basic stripe pattern:  
Begin by mowing the perimeter around the property  
(Reference Figure 4-1). Next, mow in opposing  
directions through the remaining property (as shown  
in Figure 4-1). Take care when turning at the end of  
each row to prevent turf damage. A simple "Y"  
type turn at the end of each row will reduce the  
chance of turf damage while setting the mower up  
for the next row to be mowed.  
Now, travel in the opposite direction of the original  
mowing pattern (if you were mowing North and  
South, now mow East and West, etc). Reference  
Figure 4-2.  
Finish the job by mowing the perimeter again. This  
will remove any stripe pattern irregularities left from  
turning at the end of each row and delivers a finished  
look.  
Finish the job by mowing the perimeter again. This  
will remove any stripe pattern irregularities left from  
turning at the end of each row and delivers a  
finishedlook.  
FIGURE 4-2  
FIGURE 4-1  
"Diagonal or Criss-Cross" pattern:  
This pattern is acheived using the same techniques as  
the "Checkerboard" pattern. Simply apply the stripes in a  
diagonal direction. See Figure 4-3.  
FIGURE 4-3  
5
 
TIGER STRIPER ASSEMBLY - STT  
STT with a serial number of 7219999 or Below  
4 (4x)  
30  
5
15  
17  
1 (4x)  
30  
2
4 (4x)  
3 (4x)  
5
6
7
8
1 (4x)  
20  
9
16  
15  
10  
22  
11  
14  
12  
17  
19  
8
16  
18  
13  
31  
6
25  
21  
3 (4x)  
6
6
23  
7
24  
32  
12  
22  
10  
26  
11  
23  
27  
28  
29  
9
STT-TS Exploded View  
6
 
TIGER STRIPER ASSEMBLY - STT  
Ref.  
No.  
Part  
Number  
Description  
1
2
04021-09  
423953  
Nut, Elastic Stop 3/8-16  
Striper Stop, L.H.  
3
4
5
6
7
8
9
04001-19  
04100-01  
451660  
04041-11  
04001-22  
04019-04  
04050-02  
04051-01  
04060-01  
482896  
04001-31  
482894  
04019-03  
04066-02  
451661  
Bolt, Hex Head 3/8-16 x 1"  
U-Bolt, 5/16-18 x 1"  
Mounting Bracket Weldment, LH.  
Flatwasher, 3/8-.406 x 1-1/2" 7 Gauge  
Bolt, Hex Head 3/8-16 x 2-3/4"  
Nut, Serrated Flange 3/8-16  
Retaining Ring, .750 External "E"  
Ring, Spring 1-1/2" Dia.  
Pin, Slotted Spring .156 x 3/4"  
Spring, Lock Pin  
Bolt, Hex Head 3/8-16 x 2-1/2"  
Spring, Torsion L.H.  
Nut, Serrated Flange 5/16-18  
Quick Pin, .188 Dia.  
Mounting Bracket Weldment, R.H.  
Spring, Torsion R.H.  
Hub, Striper  
Pivot Weldment, L.H.  
Pivot Weldment, R.H.  
Pin, Lift Latch  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
482895  
43648  
451664  
451665  
43654  
04012-06  
04021-09  
423954  
482897  
461707  
48100-24  
43653  
423966  
451662  
451663  
Set Screw, 3/8-16 x 1/2"  
Nut, Elastic Stop 3/8-16  
Striper Stop, R.H.  
Grip, Lift Lever  
Roller Assembly (Incl. Item 28)  
Bushing, .752 Oilite  
Roller Shaft  
Spacer, Striper Mounting  
Hinge Weldment, L.H.  
Hinge Weldment, R.H.  
7
 
TIGER STRIPER ASSEMBLY - STC  
4 (4x)  
1
17  
6
7
8
20  
1
9
16  
5
10  
15  
16  
22  
11  
14  
18  
12  
8
13  
27  
6
19  
15  
7
21  
6
6
23  
24  
28  
12  
22  
10  
26  
11  
23  
25  
3
2
9
STC-TS Exploded View  
8
 
TIGER STRIPER ASSEMBLY - STC  
Ref.  
No.  
Part  
Number  
Description  
1
423966  
Spacer, Striper Mounting  
2
43653  
Roller Shaft  
3
4
5
48100-24  
04100-01  
451660  
Bushing, .752 Oilite  
U-Bolt, 5/16-18 x 1"  
Mounting Bracket Weldment, LH. **L.H. Mounting Bracket is used on the Right Side on STC  
6
7
8
9
04041-11  
04001-22  
04019-04  
04050-02  
04051-01  
04060-01  
482896  
04001-31  
482894  
04019-03  
04066-02  
451661  
Flatwasher, 3/8-.406 x 1-1/2" 7 Gauge  
Bolt, Hex Head 3/8-16 x 2-3/4"  
Nut, Serrated Flange 3/8-16  
Retaining Ring, .750 External "E"  
Ring, Spring 1-1/2" Dia.  
Pin, Slotted Spring .156 x 3/4"  
Spring, Lock Pin  
Bolt, Hex Head 3/8-16 x 2-1/2"  
Spring, Torsion L.H.  
Nut, Serrated Flange 5/16-18  
Quick Pin, .188 Dia.  
Mounting Bracket Weldment, R.H. **R.H. Mounting Bracket is used on the Left Side on STC  
Spring, Torsion R.H.  
Hub, Striper  
Pivot Weldment, L.H.  
Pivot Weldment, R.H.  
Pin, Lift Latch  
Set Screw, 3/8-16 x 1/2"  
Nut, Elastic Stop 3/8-16  
Roller Assembly (Incl. Item 3)  
Grip, Lift Lever  
Hinge Weldment, L.H.  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
482895  
43648  
451664  
451665  
43654  
04012-06  
04021-09  
461707  
482897  
451662  
451663  
Hinge Weldment, R.H.  
9
 
NOTES  
10  
 
LIMITED WARRANTY- COMMERCIAL ACCESSORY  
AnypartoftheScagcommercialaccessorymanufacturedbyScagandfound,inthereasonablejudgmentofScag,  
tobedefectiveinmaterialorworkmanship,willberepairedorreplacedbyanAuthorizedScagServiceDealerwithout  
charge for parts and labor.  
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within  
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of  
returningitbacktotheownerafterrepairorreplacementwillbepaidforbytheowner. Scag’sresponsibilityinrespect  
toclaimsislimitedtomakingtherequiredrepairsorreplacements,andnoclaimofbreachofwarrantyshallbecause  
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the  
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service  
Dealer.  
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for  
commercial purposes, or any other income-producing purpose including rental use.  
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident, or  
thathasbeenoperatedinanywaycontrarytotheoperating instructionsasspecifiedintheOperator'sManual. The  
warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any  
accessory or parts that have not been assembled or installed as specified in the Operator's Manual.  
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not  
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable  
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or  
durability. This warranty does not cover engines and electric starters, which are warranted separately by their  
manufacturer.  
ScagPowerEquipmentreservestherighttochangeorimprovethedesignofanyaccessorywithoutassumingany  
obligation to modify any accessory previously manufactured.  
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied  
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety  
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly  
andexclusivelylimitedtotherepairorreplacementofdefectivepartsandScagdoesnotassumeorauthorizeanyone  
toassumeanyotherobligationforthem. Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,  
so the above limitation may not apply to you.  
Scagassumesnoresponsibilityforincidental,consequentialorotherdamagesincluding,butnotlimitedto,expense  
forgasoline,oil,expenseofdeliveringthemachinetoanAuthorizedScagServiceDealerandexpenseofreturning  
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time  
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of  
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
 
© 2003  
PART NO. 03142  
PRINTED 8-2003  
PRINTED IN USA  
SCAG POWER EQUIPMENT  
DIVISION OF METALCRAFT OF MAYVILLE, INC  
WWW.SCAG.COM  
 

Radio Shack Musical Instrument Amplifier PPG850A User Guide
Radio Shack Radio TRC 442 User Guide
RCA Camcorder CC6384 CC6394 User Guide
RCA Handheld TV 18V100 User Guide
REL Acoustics Speaker Storm User Guide
Remington Trimmer 117535 01A User Guide
Rheem Water Heater RTH 74XN 1 User Guide
Samsung Dishwasher DMR78 User Guide
Screenlife Video Games Simpsons User Guide
Sennheiser Headphones HD 490 II User Guide