R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
P1500
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Poulan
1030 Stevens Creek Road
Augusta, GA 30907
Poulan
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
545154716 Rev. 4 3/4/09 BRW
IDENTIFICATION OF SAFETY SYMBOLS
Store unit indoors in a high, dry place out of the reach of
children.
When servicing unit, use only identical replace-
ment parts.
Always stop unit and disconnect spark plug before
cleaning or servicing.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
Use unleaded gasoline and two--stroke oil mixed at a ratio of
40:1 (2.5%).
SAFETY RULES
If situations occur which are not covered in
this manual, use care and good judgment. If
WARNING: When using gardening
youneed assistance, contact your authorized
service dealer or call 1-800-554--6723.
appliances, basic safety precautions must al-
ways be followed to reduce the risk of fire and
serious injury. Read and follow all instructions.
This power unit can be dangerous! Operator
is responsible for following instructions and
warnings on unit and in manual. Read entire
instruction manual before using unit! Be thor-
oughly familiar with the controls and the prop-
er use of the unit. Restrict the use of this unit
to persons who have read, understand, and
will follow the instructions and warnings on
the unit and in the manual. Never allow chil-
dren to operate this unit.
OPERATOR SAFETY
S Dress properly. Always wear safety glasses
or similar eye protection when operating, or
performing maintenance, on your unit (safety
glasses are available). Eye protection should
be marked Z87.
S Always wear face or dust mask if operation is
dusty.
S Always wear heavy, long pants, long sleeves,
boots, and gloves. Wearing safety leg guards
is recommended.
INSTRUCTION
MANUAL
S Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
S Secure hair above shoulder length. Secure or
remove loose clothing or clothing with loosely
hanging ties, straps, tassels, etc. They can
be caught in moving parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants thrown
by spinning line.
SAFETY INFORMATION ON THE UNIT
DANGER:Never use blades or flailing
devices. This unit is designed for line trimmer
use only. Use of any other accessories or at-
tachments will increase the risk of injury.
3
S Stay alert. Do not operate this unit when you
are tired, ill, upset or under the influence of al-
cohol, drugs, or medication. Watch what you
are doing; use common sense.
S Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Wear hearing protection.
S Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
S Keep handles free of oil and fuel.
UNIT / MAINTENANCE SAFETY
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your right to your left. Cutting on left
side of the shield will throw debris away from
the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
WARNING: Disconnect the spark
plug before performing maintenance except
carburetor adjustments.
S Look for and replace damaged or loose parts
before each use. Look for and repair fuel
leaks before use. Keep in good working
condition.
S Replace trimmer head parts that are chipped,
cracked, broken, or damaged in any other
way before using the unit.
S Maintain unit according to recommended pro-
cedures. Keep cutting line at proper length.
S Use only 0.080 inch (2 mm) diameter Pou-
lan/WEED EATER brand line. Never use
wire, rope, string, etc.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbure-
tor by starting the engine and letting it run until
it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the
shaft.
S Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and securely
fastened.
S Store unit out of reach of children.
WARNING: The engine exhaust
from this product contains chemicals known
totheState of California to cause cancer, birth
defects or other reproductive harm.
S Make sure unit is assembled correctly as
shown in this manual.
S Make carburetor adjustments with lower end
supported to prevent line from contacting any
object.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has beenlinked to blood vesseldam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by your au-
thorized service dealer.
S Keep others away when making carburetor
adjustments.
S Use only recommended Poulan/WEED
EATER accessories and replacement parts.
S Have all maintenance and service not ex-
plained in this manual performed by an autho-
rized service dealer.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit.
S Avoid spilling fuel or oil. Wipe up all fuel spills.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before remov-
ing fuel cap.
S Always store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Keep others including children, animals, by-
standers, and helpers at least 50 feet (15 me-
ters) away. Bystanders should be encour-
aged to wear safety glasses. Stop engine
immediately if you are approached.
4
ASSEMBLY
ATTACHING SHIELD
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
ADJUSTING THE HANDLE
WARNING: When adjusting the assist
handle, be sure it remains above the safety label
and below the mark or arrow on the shaft.
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an upright
position; retighten wing nut.
4. Securely tighten wing nut onto bolt.
Slot
Shield
Bracket
Wing
Nut
Line Limiter
Blade
PIVOT
5
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Muffler
Assist Handle
Shaft Mark
or Arrow
Shaft
Safety Label
Spark Plug
Primer
Bulb
Throttle
Trigger
Trimmer
Head
STOP
Switch
Shield
Choke Lever
Fuel Mix Fill Cap
Line Limiter
Blade
Starter Handle
CHOKE
STOP SWITCH
The STOP switch is used to stop the engine. To
stop the engine, push and hold the switch in the
STOP position until the engine stops.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the RUN position.
PRIMER BULB
The PRIMER BULB removes air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
CAUTION: Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
FUEL REQUIREMENTS
WARNING: Remove fuel cap slowly
This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.
when refueling.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
IMPORTANT
Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major en-
gine performance and durability problems.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/WEED EATER brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 fluid ounces (95 ml) of oil with 1
gallon (4 liters) of unleaded gasoline. DO NOT
USE automotive oil or marine oil. These oils will
WARNING: Alternative fuels (not gas-
oline) such as E--15 (15% alcohol), E--20 (20%
alcohol), E--85 (85% alcohol) are NOT classified
as gasoline and are NOT approved for use in
2--stroke gasoline engines. Use of alternative
fuels will cause problems such as: improper
clutch engagements, overheating, vapor lock,
power loss, lubrication deficiency, deterioration
of fuel lines, gaskets and internal carburetor
components, etc. Alternative fuels cause high
6
moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
HELPFUL TIP
6. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
If your engine switch reads
“push to stop”, it is always
in the ON position.
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
8. Once the engine starts, allow it to run 10 se-
conds, then move the choke lever to the
RUN position. Allow the unit to run for 30
more seconds at RUN before releasing the
throttle trigger.
HOW TO STOP YOUR UNIT
S To stop the engine, push and hold the STOP
switch in the STOP position until the engine
stops.
S If engine does not stop, move choke to the
FULL CHOKE position.
HOW TO START YOUR UNIT
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1-800-554 -6723.
NOTE: If engine dies with the choke le-
ver in the RUN position, move the choke
lever to the HALF CHOKE position and
pull the rope until engine runs, but no
more than 6 pulls.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
STARTING A WARM ENGINE
1. Move the choke lever to the HALF CHOKE
position.
tion
2. Squeeze and hold the throttle trigger. Keep
throttle trigger fully squeezed until the en-
gine runs smoothly.
3. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
4. Allow engine to run 15 seconds, then move
1. Set unit on a flat surface.
the choke lever to RUN.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
NOTE: If engine has not started, pull starter
rope 5more pulls. If engine still does not run, it
is probably flooded.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position; then, pull the
rope to clear the engine of excess fuel. This
could require pulling the starter handle many
times depending on how badly the unit is
flooded. If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
Primer Bulb
Choke
Lever
Starter Handle
7
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
WARNING: Use only 0.080 inch (2
mm) diameter line. Other sizes of line will not
advance properly and will result in improper
cutting head function or can cause serious
injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off dur-
ing cutting and become a dangerous missile
that can cause serious injury.
OPERATING POSITION
Eye protection
ALWAYS WEAR:
CUTTING METHODS
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
whichcandamage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
Long pants
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Heavy shoes
Tip of the Line
Line Crowded Into
Cut from your right to your left.
Does The Cutting Work Area
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
S Release the throttle trigger.
S Push and hold the STOP switch in the
STOP position until the engine stops.
Wrong
S The line will easily remove grass and
weeds fromaround walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4--5 inches (10--13 cm) and
use at less than full throttle.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
TRIMMER LINE ADVANCE
S For mowing or sweeping, use full throttlefor
a good clean job.
The trimmer line will advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at full throttle.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
The most efficient line length is the maximum
length allowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
Trimming
To advance line:
S Operate the engine at full throttle.
S Hold the trimmer head parallel to andabove
the grassy area.
S Tap the bottom of the trimmer head lightly
on the ground one time. Approximately 2
inches (5 cm) of line will be advanced with
each tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient line length.
3 inches (8 cm)
above ground
SCALPING -- The scalping technique re-
moves unwanted vegetationdown to the
ground. Hold the bottom of the trimmer head
about 3 inches (8 cm) above the ground and
at an angle. Allow the tip of the lineto strikethe
ground around trees, posts, monuments, etc.
This technique increases line wear.
8
Scalping
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
Swee
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Mowing
MAINTENANCE
CLEAN AIR FILTER
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
HELPFUL TIP
1. Clean the air filter cover and the area
around it to keep dirt from falling into the
carburetor chamber when the cover is
opened.
2. Open air filter cover by pushing button
(see illustration). Remove air filter.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Replace air filter and close cover.
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan/WEED EATER may
not pay for repairs under warranty. It is
your responsibility to maintain and per-
form general maintenance.
CHECK FOR LOOSE
Button
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
Air Filter
S Housing Screws
S Assist Handle Screws
S Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S STOP Switch -- Ensure STOP switch func-
tions properly by pushing and holding the
switch in the STOP position. Make sure en-
gine stops. Restart engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
Air Filter Cover
MUFFLER AND SPARK ARREST-
ING SCREEN
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen.
For normal homeowner use, however, the
muffler and spark arresting screen will not re-
quire any service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your authorized service dealer.
INSPECT AND CLEAN UNIT AND
LABELS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
9
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch (0.6 mm). Igni-
tion timing is fixed and nonadjustable.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
4. Reinstall the spark plug boot.
SERVICE AND ADJUSTMENTS
2. Remove trimmer head by turning counter-
clockwise (looking from bottom of unit).
3. Thread replacement trimmer head onto the
shaft by turning clockwise. Only tighten
hand tight!
LINE REPLACEMENT
1. Remove spool by firmly pulling on tap
button.
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut
two lengths of 12-1/2 feet (3.8 meters) of
0.080 inch (2 mm) diameter Poulan/
WEED EATER brand line.
CARBURETOR IDLE SPEED
ADJUSTMENT
WARNING: Never use wire, rope,
string, etc., which can break off and becomea
dangerous missile.
4. Insert ends of the lines about 1/2 inch (1
cm) into the small holes on the inside of
spool.
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head will be spinning during this procedure.
Wear your protective equipment and observe
all safety precautions.
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
Spool
Small
Holes
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Line exit holes
Line in Notch
To adjust idle speed:
Allow engine to idle. Adjust speed until engine
runs without stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
crease enginespeed if enginestalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed.
Line in Notch
Hub
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
Idle Speed Screw
6. Push the lines into the notches, leaving 3
to 5 inches (7 -- 12 cm) unwound.
7. Insert the lines into the the exit holes in
the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
10. Pull the lines extending outside of the hub
to release the lines from the notches.
REPLACING THE TRIMMER HEAD
1. Hold the dust cup with a wrench to keep
the shaft from turning while removing and
installing trimmer head.
Air Filter Cover
Dust
If you require further assistanceor are unsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
10
STORAGE
HELPFUL TIP
WARNING: Perform the following
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
11
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Carburetor requires
adjustment.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
1. See “Carburetor Idle Speed Adjustment”
in Service and Adjustments Section.
2. Crankshaft seals worn. 2. Contact an authorized service dealer.
3. Compression low.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Fuel mixture incorrect. 1. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
2. Air filter dirty.
3. Carburetor requires
adjustment.
2. Clean or replace air filter.
3. Contact an authorized service dealer.
1. Fuel mixture incorrect.
1. See “Fueling Engine” in Operation
section.
Engine runs
hot.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
12
LIMITED WARRANTY
Poulan, a division of Husqvarna Consumer
In Canada, contact:
Poulan
Outdoor Products N.A., Inc., warrants to the
original consumer purchaser that each new
Poulan brand gasoline tool or attachment is free
from defects in material and workmanship and
agrees to repair or replace under this warranty
any defective gasoline product or attachment as
follows from the original date of purchase.
2 YEARS - Parts and Labor, when used for
household purposes.
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan for this
tool. This warranty does not cover tune--up,
spark plugs, filters, starter ropes, cutting line, or
rotating head parts that will wear and require
replacement with reasonable use during the
warranty period. This warranty does not cover
pre--delivery setup or normal adjustments
explained in the instruction manual. This
warranty does not cover transportation costs.
In the event you have a claim under this
warranty, you must return the product to an
authorized service dealer.
WARRANTIES
EXCEPT
THOSE
EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION
OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION MAY
NOT APPLY TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
The policy of Poulan is to continuously
improve its products. Therefore, Poulan
reserves the right to change, modify, or
discontinue models, designs, specifications,
and accessories of all products at any time
without notice or obligation to any purchaser.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan, a division of Husqvarna Consumer
Outdoor Products N.A., Inc.
1030 Stevens Creek Road
Augusta, GA 30907
1--800--554--6723
U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and Poulan are
pleased to explain the emissions control system
warranty on your year 2009 and later small off--
road engine. In California, all small off--road en-
gines must be designed, built, and equipped to
meet the State’s stringent anti--smog stan-
dards. Poulan must warrant the emission
control system on your small off--road engine
for the periods of time listed below provided
there has been no abuse, neglect, or improp-
er maintenance of your small off--roadengine.
Your emission control system includes parts
such as the carburetor, the ignition system and
the fuel tank. Where a warrantable condition
exists, Poulan will repair your small off--road
engine at no cost to you. Expenses covered
under warranty include diagnosis, parts and
labor. MANUFACTURER’S WARRANTY
COVERAGE: If any emissions related part
on your engine (as listed under Emissions
Control Warranty Parts List) is defective or a de-
fect in the materials or workmanship of the en-
gine causes the failure of such an emission re-
lated part, the part will be repaired or replaced
by Poulan. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off--road en-
gine owner, you are responsible for the per-
formance of the required maintenance listed
in your instruction manual. Poulan recom-
mends that you retain all receipts covering
maintenance on your small off--road engine,
but Poulan cannot deny warranty solely for
the lack of receipts or for your failure to en-
sure the performance of all scheduled main-
tenance. As the small off--road engine owner,
you should be aware that Poulan may deny
you warranty coverage if your small off--road
engine or a part of it has failed due to abuse,
neglect, improper maintenance, unapproved
modifications, or the use of parts not made or
approved by the original equipment manufac-
turer. You are responsible for presenting your
small off--road engine to an Poulan authorized
13
repair center as soon as a problem exists. War-
ranty repairs should be completed in a reason-
able amount of time, not to exceed 30 days. If
you have any questions regarding your war-
ranty rights and responsibilities, you should
contact your nearest authorized service cen-
ter, call Poulan at 1--800--554--6723, or send
e-mail correspondence to emission.warranty
@HCOP--emission.com. WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off--road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years fromthe initialdate of purchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved Poulan
servicing center. If you have any questions
regarding your warranty rights and responsi-
bilities, you should contact your nearest au-
thorized service center, call Poulan at
1--800--554--6723, or send e-mail correspon-
CONSEQUENTIAL DAMAGES: Poulan
may be liable for damages to other engine
components caused by the failure of a war-
ranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD -ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. Poulan is not liable to cover failures of
warranted parts caused by the use of add--on or
modified parts. HOW TO FILE A CLAIM: If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center, call
Poulan at 1--800--554--6723, or send e-mail
correspondence
to
emission.warranty
@HCOP--emission.com. WHERE TO GET
WARRANTY SERVICE: Warranty services or
repairs shall be provided at all Poulan service
centers. Call: 1--800--554--6723 or send e-mail
correspondence
to
emission.warranty
@HCOP--emission.com. MAINTENANCE,
REPLACEMENT AND REPAIR OF EMIS-
SION RELATED PARTS: Any Poulan ap-
proved replacement part used in the perfor-
mance of any warranty maintenance or repair
on emission related parts will be provided
without charge tothe owner if thepart is under
warranty. EMISSION CONTROL WARRAN-
TY PARTS LIST: Carburetor, air filter (covered
up to maintenance schedule), ignition system:
spark plug (covered up to maintenance sched-
ule), ignition module, muffler including catalyst (if
equipped), fuel tank. MAINTENANCE
STATEMENT: The owner is responsible for
the performance of all required maintenance
as defined in the instruction manual.
dence
to
emission.warranty@HCOP--
emission.com. WARRANTY PERIOD: Any
warranted part which is not scheduled for re-
placement as required maintenance, or which
is scheduled only for regular inspection to the
effect of “repair or replaceas necessary” shall
be warranted for 2 years. Any warranted part
which is scheduled for replacement as re-
quiredmaintenance shall bewarranted for the
period of time up to the first scheduled re-
placement point for that part. DIAGNOSIS:
The owner shall not be charged for diagnostic
labor which leads to the determination that a
warranted part is defective if the diagnostic
work is performed at an approved Poulan
servicing center.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
14
|