908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 1
ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 31
Instruction
manual
Cordless Jigsaw
MODEL 643
PATENT PENDING
MODEL 8924
IMPORTANT
To learn more about Porter-Cable
visit our website at:
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Copyright © 2001 Porter-Cable Corporation
Part No. 908937 - 12-20-02
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 3
TOOL USE AND CARE
1. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
2. Do not force tool. Use the correct tool for your application. The
correct tool will do the job better and safer at the rate for which it is designed.
3. Do not use tool if switch does not turn it on or off. A tool that cannot
be controlled with the switch is dangerous and must be repaired.
4. Disconnect battery pack from tool and place the switch in the locked
or OFF position before making any adjustments, changing accessories,
or storing the tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
6. When battery pack is not in use, keep it away from other metal
objects like: paper clips, coins, keys, nails, screws, or other small metal
objects that can make a connection from one terminal to another.
Shorting the battery terminals together may cause sparks, burns, or a fire.
7. Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with sharp cutting edge are less likely to bind and are easier
to control.
8. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation. If
damaged, have the tool serviced before using. Many accidents are caused
by poorly maintained tools.
9. Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool may create a risk
of injury when used on another tool.
SERVICE
1. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel may result in a
risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance Section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instructions may create a
risk of shock or injury.
SPECIFIC SAFETY RULES AND SYMBOLS
1. Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring. Contact with a “live” wire
will also make exposed metal parts of the tool “live” and shock the operator.
2. Be aware that this tool is always in an operating condition, because it
does not have to be plugged into an electrical outlet. Always set the trigger
switch to the locked OFF position when installing or removing the battery pack
or saw blade.
3. Keep blades sharp.
4. Keep hands away from cutting area. When sawing never reach
underneath or behind the material being cut for any reason.
5. When you have finished a cut be careful not to come into contact with
the blade. Turn off the motor immediately.
6.
WARNING: EXERCISE EXTREME CAUTION WHEN BLIND CUTTING
TO BE CERTAIN THAT THERE ARE NO FOREIGN OBJECTS SUCH AS
ELECTRICAL WIRE, CONDUIT, PLUMBING PIPES, ETC., THAT MAY COME
INTO CONTACT WITH THE BLADE.
3
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 4
7. Some wood contains preservatives which can be toxic. Take extra care
to prevent inhalation and skin contact when working with these materials.
Request, and follow, all safety information available from your material supplier.
8.
WARNING: There are certain applications for which this tool was
designed. Porter-Cable strongly recommends that this tool NOT be modified
and/or used for any application other than for which it was designed. If you
have any questions relative to its application DO NOT use the tool until you
have written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
SYMBOL
V
A
DEFINITION
.......................... volts
.......................... amperes
Hz
W
.......................... hertz
.......................... watts
PSI
Min.
.......................... pounds per square inch
.......................... minimum
Max. .......................... maximum
in.
MM
h
min
s
.......................... inch
.......................... millimeters
.......................... hours
.......................... minutes
.......................... seconds
.......................... alternating current
.......................... direct current
.......................... no load
n0
.......................... alternating or direct current
.......................... Class II Construction
…/min .......................... revolutions or reciprocation per minute
SAFETY INSTRUCTIONS FOR CHARGER AND BATTERIES
1. SAVE THESE INSTRUCTIONS. This manual contains important safety
and operating instructions for Porter-Cable Battery Charger.
2. Before using a battery charger, read all instructions and cautionary
markings on (1) battery charger, (2) battery pack, and (3) product using battery.
3. CAUTION: To reduce risk of injury, a Porter-Cable charger should only be
used to charge a Porter-Cable battery pack. Other types of batteries may
burst causing personal injury and damage. Do not charge a Porter-Cable
battery pack with any other charger.
4. Do not expose charger to rain, snow or frost.
5. Do not abuse cord. Never carry charger by cord or yank it to disconnect
from receptacle. Pull by plug rather than cord when disconnecting charger.
Have damaged or worn power cord and strain reliever replaced immediately.
DO NOT ATTEMPT TO REPAIR POWER CORD.
6. Make sure cord is located so that it will not be stepped on, tripped over,
or otherwise subjected to damage or stress.
4
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 5
7. Do not use an extension cord unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure:
A. That the pins on plug of extension cord are the same number, size and
shape as those of plug on charger.
B. That the extension cord is properly wired and in good electrical
condition.
C. Wire Size of cord is at least as specified in following chart:
LENGTH OF CORD IN FEET
25
50
100
150
16
AWG SIZE OF CORD
18
18
18
D. If an extension cord is to be used outdoors it must be marked with the
suffix W-A or W following the cord type designation. For example –
SJTW-A to indicate it is acceptable for outdoor use.
8. Do not operate charger with damaged cord or plug – have them replaced
immediately, to avoid a hazard. DO NOT ATTEMPT TO REPAIR POWER CORD.
9. Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it to a qualified serviceman.
10. Do not disassemble charger or battery pack. Take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
11. Unplug charger from outlet before attempting any maintenance or
cleaning – to reduce risk of electric shock.
12. Charge the battery pack in a well ventilated place, do not cover the
charger and battery pack with a cloth, etc., while charging.
13. Do not store the charger or battery pack in locations where the
temperature may reach or exceed 122°F (50°C) (such as a metal tool shed, or
a car in the summer), which can lead to deterioration of the storage battery.
14. Do not charge battery pack when the temperature is BELOW 40°F or
ABOVE 104°F (4.4/40°C). This is very important for proper operation.
15. Do not incinerate battery pack. It can explode in a fire.
16. Do not charge battery in damp or wet locations.
17. Do not attempt to charge any other cordless tool or battery pack with the
Porter-Cable charger.
18. Do not short across the terminals of the battery pack: EXTREMELY
HIGH TEMPERATURES COULD CAUSE PERSONAL INJURY OR FIRE.
19. Double insulated tools are equipped with a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a polarized outlet. Do
not change the plug in any way. Double Insulation eliminates
the need for the three wire grounded power cord and grounded power supply
system.
20. Dispose of expended batteries properly. The
Porter-Cable Battery Packs contains rechargeable,
nickel-cadmium batteries. These batteries must be
recycled or disposed of properly. Drop off expended
battery packs at your local replacement battery
retailer, your local recycling center, or at a Porter-
Cable Service Center (see list on back page of this
manual). Applicable fees for the collection and
recycling of these batteries (in the United States),
RBRC™ is a Trademark of the
have been paid to the RBRC™. For further
Rechargeable Battery Recyling
Corporation.
information, call: 1-800-8-BATTERY.
5
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 6
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable Model 643 Cordless Jigsaw is designed for cutting materials of
the following MAXIMUM thickness: wood 41/3", plastic and fiberglass 11/4",
aluminum and nonferrous metals 13/16", mild steel 3/8", and stainless steel 1/8".
ASSEMBLY
ANTI-SPLINTER BASE INSERT INSTALLATION
The anti-splinter base insert is used to
reduce chipping and splintering of the
top fibers of plywood, paneling, and
other splinter prone materials. When this
insert is used it is not necessary to have
the good or finished side of the work
down during the cutting operation.
Install the insert as shown in Fig. 1.
NOTE: When using the anti-splinter
insert, the base should be set to the
forward most position (Fig. 9).
Fig. 1
ANTI-MAR PLASTIC SUB-BASE INSTALLATION
CAUTION: REMOVE BATTERY PACK.
The anti-mar plastic sub-base is used when cutting on finished surfaces to
prevent the normal metal base from scratching, gouging, or otherwise marring
the surface of the material to be cut.
To install the plastic sub-base, remove the six screws (Fig. 9) from the bottom
of the base, remove the metal sub-base, place the plastic sub-base on the
saw, and reinstall the six screws. Be sure to save the metal sub-base for
reuse.
BLADE INSTALLATION
1. Remove anti-splinter insert if installed.
2. Gently squeeze the switch trigger until the blade shaft moves slowly and stop
the motor when the blade shaft is at or near the bottom of its stroke (Fig. 6).
CAUTION: REMOVE BATTERY PACK.
B
A
Fig. 2
Fig. 3
6
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 7
3. Open the blade clamp by rotating the
movable lever (B), Fig. 2, towards the
stationary lever (A), Fig. 2, as far as it will go
and hold.
4. While holding the blade clamp open;
move lever (A) as far forward as it will go,
(see Figs. 2 & 3), and hold.
NOTE: Steps 3 and 4 should be done in
one motion.
5. With the teeth of the blade toward the
front of the saw, insert the blade through the
blade guide into the blade holder as far as it
will go and release the levers (Fig. 4).
Fig. 4
6. Pull up on the blade (Fig. 3) until it locks in place. The blade is properly
installed when the levers are aligned as shown in Fig. 4.
BLADE REMOVAL
1. Remove the anti-splinter insert if installed.
2. Gently squeeze the switch trigger until the blade shaft moves slowly and stop
the motor when the blade shaft is at or near the bottom of its stroke (Fig. 6).
CAUTION: REMOVE BATTERY PACK.
3. Open the blade clamp by rotating the movable lever (B), Fig. 2, towards the
stationary lever (A), Fig. 2, as far as it will go.
4. Move the blade shaft forward until the blade is clear of the blade guide.
5. Grasp the tip of the blade, move it towards the blade holder lever/right
hand side of saw and pull the blade out of the clamp.
OPERATION
TO START AND STOP SAW
Make sure power circuit voltage is the same as shown on the specification
plate on the saw, and that saw switch is OFF. Connect battery pack.
1. Squeeze trigger switch (A), Fig. 5, to start motor. Release trigger to stop
motor.
2. Lock-Out Button – A lock-out button (B), Fig. 5, is provided to prevent
unintentional starting. To lock the switch trigger “OFF”, push the button to the
right.
To UNLOCK the lock-out, push the button to the left.
B
A
Fig. 5
7
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 8
VARIABLE SPEED
This saw is equipped with a variable speed control switch. The speed range is
0 to 2200 SPM. The speed is adjusted by squeezing the switch trigger. The more
the switch trigger is squeezed the higher the speed.
Use higher speed for fast cutting when finish and accuracy are not critical.
Use slower speed when accuracy and finish are critical or for delicate
materials.
BLADE ORBIT
The blade orbit may be varied by turning knob (A), Fig. 6, to any of four
positions indicated by the numbers “0” through “3”, with “0” producing no
orbit and “3” producing maximum orbit. The orbit may be adjusted with or
without the motor running. Move knob (A), Fig. 6, to the detent in the housing
corresponding to the number on the housing. The knob is shown in the
vertical position “3”. The horizontal position would be setting “0”. Metal
cutting should be performed in orbit setting “0”.
Use of higher orbit settings when performing intricate scroll cuts may cause
blade breakage. The lower orbit settings are recommended for scrolling. Orbit
position “0” will produce the most accurate cuts with less splintering and the
longest blade life.
A
B
Fig. 6
CHIP BLOWER
This saw is equipped with a chip blower to keep the cutting area free of chips.
Use knob (B), Fig. 6, to turn the chip blower on and off. The knob is shown in
the “ON” position, to turn the chip blower “OFF” turn the knob clockwise until
it stops.
PLUNGE CUTTING
WARNING: When cutting into a
wall avoid contact with all
exposed metal on the tool to
prevent electrical shock hazard
resulting from accidentally cutting
into a live wire. HOLD SAW AS
ILLUSTRATED IN FIG. 7.
Fig. 7
8
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 9
One of the distinctive and important
features of the Porter-Cable jigsaw is the
ability to start the cut, (in wood only)
within an area, without making drilled
holes first. This is especially important
when making cutouts for electrical
outlets in finished walls, openings in
cabinet tops for sinks and openings for
plumbing fixtures.
NOTE: When plunge cutting, it is
recommended the orbit knob be set
to position “3”.
Fig. 8
First, measure the area to be cut out and
mark it clearly with a pencil, chalk or
scriber. Choose a convenient starting point and hold the jigsaw over the point
and inside the line of waste. Tip the machine forward until the front edge of the
base rests firmly on the surface of the material with the tip of the blade clear
of the work surface, as shown in Fig. 8. Turn motor “ON” and slowly lower the
back of the machine until the base is fully seated on the surface of the work.
Now, guide the cutting along the inside of the marked area. If sharp corners
are desired cut right up to the corner of the marked edge. Stop and back up
just a bit, start the turn and cut along the side. Do the same at each corner
until you end up where you started. Then, go back and cut into each corner
from the opposite direction. The base of the machine is wide enough so you
will have a solid guiding surface on either side of the cut.
BASE ADJUSTMENT
The base may be adjusted two ways, front to rear and tilted either left or right
for making bevel cuts. The base has a detent at the 0 (90 degree) setting and
at 15, 30 and 45 degree setting both left and right of center.
The base is set at its forward most position at the factory. The base can be
adjusted to the rear for making flush cuts around walls and other similar areas.
To move the base forward or backward, turn the saw on its side, loosen screw
(A), Fig. 9, move the base to the desired position and retighten the screw.
NOTE: When making bevel cuts, the base should be set to the
forward most position (Fig. 9).
A
Fig. 9
9
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 10
A
Fig. 10
Fig. 11
To tilt the base, pull the lever out of the end of clamp screw (A), Fig. 10, rotate
the lever toward the front of the saw (Fig. 11) and turn the lever counter-
clockwise until the base can be tilted. Set the base at the desired setting and
tighten the screw by turning the lever clockwise.
NOTE: After each 90 degree or half turn, it will be necessary to move
the lever back to the opposite side of the saw.
USING THE SAW
First, secure the material in a bench vise or with clamps to the work table. This
is especially important when sawing small pieces or thin material. As the work
progresses in scroll or curved cut-out pieces, the material can be readjusted
to accommodate the movement of the saw. If the work is large enough it can
be held by hand across saw horses. The saw cuts freely with only light forward
feed pressure on the tool. Forcing the saw will not make it cut faster.
To start the cut, secure the work, mark the line of cut clearly, place the forward
edge of the saw base firmly on the edge of the material, start the motor and
move the blade into the work.
DO NOT FORCE, LET THE SAW DO THE WORK. Move the machine forward
only rapidly enough to keep the blade cutting.
You will find that the open throat and clear forward edge of the saw base make
it easy to follow the line and cut closely to the pattern. You need not cut
oversize for hand finishing or sanding on most materials.The smoothness of
cut will often make further sanding unnecessary.
10
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 11
BATTERY OPERATION
CHARGING THE BATTERY PACK GENERAL
Before using your cordless tool for the first time, the battery pack should be
fully charged. If the battery pack is installed, remove it by following
instructions under INSTALLING OR REMOVING BATTERY PACK.
As a battery pack approaches the discharged state, you will notice a sharp
drop in tool performance. When the tool is unable to perform the task at hand,
it is time to recharge the battery pack. Recharging the battery pack before this
condition is reached will reduce the total work life of the pack. Discharging the
pack beyond this point can damage the pack.
NOTE: Battery temperature will increase during and shortly after use.
Batteries may not accept a full charge if they are charged immediately
after use. Allow the battery pack to cool to room temperature before
charging for best results.
The battery charger may rest on the four pads provided on the bottom of the
case or be mounted on a wall by utilizing the two key hole slots provided.
CAUTION: Vent slots in top and bottom of charger must not be
obstructed. Do not charge battery when temperature is BELOW 40°F
or ABOVE 104°F (4.4/40°C).
NORMAL CHARGING
Make sure power circuit voltage is the same as that shown on the charger
specification plate. Connect charger to power source. The red and green lights
will flash once to indicate that power is connected properly and the charger is
ready for operation.
Position the battery pack on charger, align rails on battery pack (A) Fig. 13 with
four tabs (C) Fig. 12 on charger. Slide battery forward on charger until it stops.
The green light (A) Fig. 12 should begin to flash rapidly indicating that the
battery pack is receiving a “fast charge”. (If the green light does not flash or if
the red light (B) illuminates, see DIAGNOSTICS”). After approximately one
hour, the “Fast Charge” indicator light should glow continually, indicating that
the battery pack is fully charged and that the charger is now in a “Maintenance
Charge” mode. The battery pack can be left on “Maintenance Charge” until
you are ready to use it.
Depending on room temperature, line voltage, and existing charge level, initial
battery charging may take longer than one hour.
Disconnect charger from power source when not in use.
A
B
C
Fig. 12
11
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 12
DIAGNOSTICS
The charger is equipped with a diagnostic system that automatically checks
the battery pack each time a pack is inserted into the charger.
If no problems are found, the charger will automatically switch to “Fast
Charge” mode as described in NORMAL CHARGING. If a problem is found, it
will be indicated by the charger indicator lights (see Fig. 12), as follows:
• If the green light (A) flashes slowly after battery pack is inserted in charger,
the battery pack temperature is either too high or too low for charging. If left
alone, the charger will continue to monitor the battery pack temperature and
will begin charging when the temperature reaches an acceptable level.
• If the red light (B) flashes continuously, the battery pack has failed (pack is
not chargeable and requires replacement).
INSTALLING OR REMOVING BATTERY PACK
WARNING: Always set the trigger switch to the locked OFF position when
installing or removing the battery pack.
TO REMOVE BATTERY PACK: Depress the battery release button (B) Fig. 13,
and pull battery pack out of tool.
TO INSTALL BATTERY PACK: Align rails (A) Fig. 13, on battery pack with slots
on tool and push battery pack onto tool until it locks in place.
A
B
Fig. 13
12
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 13
MAINTENANCE
KEEP TOOL CLEAN
All plastic parts should be cleaned with a soft damp cloth. NEVER use
solvents to clean plastic parts. They could very possibly dissolve or otherwise
damage the material.
FAILURE TO START
Should your tool fail to start, make sure battery pack is charged and properly
installed in drill.
BATTERY
The battery pack will discharge by itself without damage if stored for long
periods of time, and may require recharging before use.
LUBRICATION
For your continued safety and electrical protection, lubrication and service on
this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE
SERVICE STATION or a PORTER-CABLE/DELTA FACTORY SERVICE
CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
Authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected; worn parts replaced, when necessary; relubricated with fresh
lubricant, and performance tested.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY
SERVICE CENTER. All repairs made by these agencies are fully guaranteed
against defective material and workmanship. We cannot guarantee repairs
made or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable •
Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-
Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.
WARNING: Since accessories other than those offered by Porter-Cable
• Delta, have not been tested with this product use of such accessories
could be hazardous. For safest operation, only Porter-Cable •Delta
recommended accessories should be used with this product.
13
908937 - 12-20-02.qxd 12/20/02 10:02 AM Page 14
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.
14
908937 - 12-20-02.qxd 12/20/02 10:04 AM Page 48
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
Cleveland 44125
ARIZONA
MINNESOTA
ILLINOIS
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Minneapolis 55429
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
MISSOURI
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
MARYLAND
St. Louis 63119
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
COLORADO
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
OHIO
MICHIGAN
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center,
or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the
nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame
al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-Cable
•
•
•
•
•
Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable
•
Delta, Centro de Servicio Autorizado o Centro de
Servicio de Fábrica Porter-Cable
Servicio de Fábrica Porter-Cable
•
Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
•
Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-
Cable
•
Delta, s’adresser à tout distributeur Porter-Cable
•
Delta, centre de service agréé ou centre de service d’usine Porter-Cable
•
Delta. Si
Delta le
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable
•
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 836-2840
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-
Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design),
PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®,
QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™,
Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®,
Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Printed in U.S.A.
|