E X S E RIE S
POLK AUDIO
5601 METRO DRIVE
BALTIMORE, MARYLAND 21215
(800)377-7655
Polk Audio
EX Series II Owner's Manual
POLK AUDIO EUROPE LTD.
TYTTENHANGER HOUSE
COURSERS ROAD
ST. ALBANS AL4 OPG
GREAT BRITAIN
TEL: 1727.827311
POLK AUDIO GERMANY
UNTERTUERKHEIMER STR. 24
D - 66117 SAARBRUECKEN
GERMANY
TEL: (49) 681 5800 888
"Polk Audio" and "The Speaker Specialists" are
trademarks of Britannia Investment Corporation used
under license by Polk Audio Incorporated.
EX SERIES II SUBWOOFER FEATURES:
BUILDING YOUR OWN SUBWOOFER ENCLOSURE
The EX Series II subwoofers use the latest technologies and highest quality materials to
Since the subwoofer enclosure is so critical to getting the best performance from your EX
provide you with the best bass response and greatest reliability possible. The EX Series II
subwoofers have been optimized to give skull-collapsing performance from a wide variety of
enclosure types. Some of their design elements are:
subs, you should ask yourself the following questions:
1. Do I really enjoy working with my hands?
2. Do I have good woodworking and mechanical skills?
• 1mm thick mineral filled polymer composite cones – ultra stiff and strong to
withstand the enormous pressures generated inside subwoofer enclosures without cone
breakup and distortion.
3. Do I have or have access to woodworking and electrical tools?
4. Do I have a solid understanding about musical reproduction in an automobile?
• Injection molded polypropylene dustcap – prevents distortion due to the build up of air
pressure behind the cap.
• Rubber surrounds – provide a much tighter and more durable air seal behind the
cone than foam, paper or cloth surrounds, for deep, tight, quick bass. In addition,
rubber surrounds do not dry rot like foam surrounds.
• If you answered "NO" to any of the above questions, we recommend you choose one of
these two possible alternatives. First, you may choose a pre-built subwoofer enclosure
available from companies like Obcon, ADD and Q-Logic or an enclosure kit from
BassLine and other manufacturers. The second alternative is to have your authorized
Polk Audio dealer design and build a woofer box for you.
• Four layer, 2" voice coil (EX10 and EX12 only) – handles heat generated when your
amp is really cranking.
• If you answered "YES" to all of the above, let’s review some basics before you begin.
• Vented pole piece – lets air circulate over the voice coil to keep it cool and in control
even when the bass is really thumping.
Effective planning will help ensure that your system performs the way that you want it
to. Every car is different, and everyone has slightly different musical tastes. You need to
make informed decisions before you begin to build your system. Polk EX subwoofers
are designed to work in a wide variety of enclosures, and each enclosure design has a
unique list of pros and cons. The following is the basic information about the most
popular automotive subwoofer enclosures.
It is not possible to provide all of the information for enclosure options here. This
manual will give you enough information to build a great sounding enclosure. If you
are interested in a greater choice of enclosure designs, your Polk EX Series II dealer
has extensive experience designing woofer boxes and will be more than happy to work
with you. If you prefer, you can call our Customer Service Department from 9AM to
5PM, Monday through Friday, Eastern Time at (800)377-7655 or email us at
4
5
FIGURE 1.
ACOUSTIC SUSPENSION ENCLOSURES
The acoustic suspension cabinet is a sealed airtight box,
and is the simplest, easiest box to build. It is a very
predictable enclosure with easily calculated
parameters and a smooth natural sound. Properly
built acoustic suspension cabinets have a
reasonably flat frequency response that begins
rolling off at 12 dB per octave at the frequencies
below its cabinet resonance. This works very well
inside a car because of a natural phenomenon
called “room gain” or “transfer function” that gives
you a 12 dB per octave increase in bass frequencies. You can
roughly calculate at what frequency this gain begins by using the
together and cancel themselves out, making no bass at all. If you plan on building an
infinite baffle system you must plan on sealing all of the air passages between the trunk and
the passenger compartment (not an easy job). Also the metal used on the rear decks of cars
does not make for a very good baffle board; the metal will tend to resonate and again cancel
out the bass frequencies. You should plan on mounting your woofers on a non resonant
wooden baffle. A properly designed infinite baffle enclosure will roll off at 6 dB per octave
below cabinet (speaker) resonance, and will have a very smooth frequency response. The
infinite baffle is the least efficient box design.
TUNED PORT ENCLOSURES
FIGURE 3.
The tuned port enclosure is similar to the acoustic suspension box
except that it uses a port to take the back wave from the
speaker and “tune” it to reinforce the front wave. A
equation F= 565 / L. F is the frequency at which bass gain begins, and L is the longest
dimension of your “room”. If, for example, you measured the longest dimension in the
interior of your car as 5.65 ft., the room gain begins at 565 / 5.65 or 100 Hz. If your goal
was perfectly flat frequency response, you would design your cabinet for this particular car
to have a resonance frequency of 100 Hz. Since most people want more bass than a flat
frequency response yields, tuning the cabinet at a lower frequency, say 50 Hz, would give
you a gain of 12 dB per octave between 100 and 50 Hz and flat response from 50 Hz down.
The larger the cabinet, the lower the resonant frequency, and the lower the efficiency. Two
identical systems will sound very different in a Honda vs. a Cadillac. The bigger the car, the
lower the frequency at which room gain begins.
system becomes more efficient when the
frequencies of the port and the front wave are in
phase. It is absolutely critical that the dimensions
of the box and the port are perfect, or the back and
front waves will cancel each other out, reducing
your bass output. Tuned port enclosures tend to be
peaky in the bass, and many people (particularly
Bassheads) like the punchiness of the sound. Tuned port
enclosures roll off at a very steep 18 dB per octave below cabinet
resonance, which means that the room gain of the car will not help to extend the lowest of
frequencies. In addition, the woofer becomes “unloaded” below the tuning frequency of the
port and very loud musical information below these frequencies can damage a woofer.
FIGURE 2.
INFINITE BAFFLE
Also known as free air enclosures, this essentially means mounting
your woofers in the rear deck of your car, and not building a box
BAND-PASS ENCLOSURES
FIGURE 4.
Band-Pass boxes can be built in a near infinite amount of
around the speakers. At first glance, this would seem to be a very easy
configurations. They incorporate at least two
way to install your new speakers, but many problems can occur if this
individual chambers and are by far the most
is not done exactly right. In the acoustic suspension design described
complicated box to model and build. The theory
behind band-pass boxes is to limit the frequencies
produced by the subwoofer, thereby making it more
efficient in the frequencies that it produces.
A by-product of this efficiency is that it is often
possible to build a band-pass box much smaller
than its equivalent acoustic suspension box and get
the same quantity of acoustic output. If you have a very
small car with limited room for a subwoofer box, a band-pass box
above, the box is providing two major functions: first, the air that is
sealed within the box acts as a spring to help support the suspension of
the speaker. As the woofer cone moves in towards the box, the air in the
box pressurizes; and as the cone moves out a vacuum forms. This helps to
keep the cone from traveling too far and destroying itself. An Infinite Baffle design
has no box; therefore, it has no trapped air behind the speaker to act as a spring. If your
speakers are not specifically designed for infinite baffle use they can be damaged. Your new
EX Series II woofers are designed for use in enclosures and are not recommended for
infinite baffle use. The second thing that a sealed box provides is sound wave isolation
created from the front of the speaker cone due to the waves that are created from the back of
the speaker cone. If the two wave fronts are not isolated from each other they will mix
may be a good choice. The downsides of the band pass box are numerous. First, the
construction must be flawless, any airleaks or rattles will seriously degrade performance.
6
7
PARTS YOU WILL NEED TO BUILD YOUR ENCLOSURE
There are three choices of enclosure material:
Second, designing band-pass boxes is as much art as science, just because a computer
program says that a certain design will work is no guarantee that you will like the
performance of the finished design. Third, all subwoofer enclosures exhibit a phenomenon
known as “group delay”. It means that the sounds from the subwoofer will lag in time from
the sounds created by your high frequency speakers. This causes a smearing of the sound
and in worst cases a ping-pong effect from the highs in the front of your car to the bass in
the rear. Band-pass boxes are especially prone to long group delays. Finally, the pressures
and vacuums formed within a band-pass box can be extremely high, if the subwoofer you
are utilizing does not have a very stiff cone. It can buckle under the high pressures, making
very bad noises. The Polk EX subwoofers utilize 1mm thick mineral filled cones, and are
extremely well suited for use in band-pass enclosures.
1. Particle board
2. Medium density fiberboard (MDF)
3. Marine grade plywood
These materials range in price as well as availability. Particle board is the most common,
least costly, and can be purchased at most hardware stores. MDF and marine grade plywood,
although preferable, are usually much harder to find, and more costly. Whichever you
choose, we recommend that its thickness be 3/4". This will provide the rigidity necessary for
optimum performance.
If you have never built an enclosure before, we are going to try to make this as easy and
painless as possible. If you have built enclosures before, you can skip this section and go
right to the specification page to get the technical parameters.
TOOLS YOU WILL NEED TO BUILD YOUR ENCLOSURE
If you have decided to build your own enclosure for your Polk EX subwoofers, here is a list
of the tools you should have available.
1. Wood (particle board, MDF, or marine grade plywood ) 4' x 8' x 3/4" sheet
2. Wood glue (one bottle)
3. 1 1/4"x #8 wood screws (one box)
4. Caulking gun and silicon caulk (two tubes)
5. Terminal cup (one per speaker) available at electronic parts stores
6. Speaker wire
7. Carpet (optional)
8. Grilles to protect your subwoofers (optional)
9. Solderless speaker connectors (available at electronic parts stores)
• Calculator
• Assorted drill bits
• Screwdriver bit for drill or manual screwdriver
• Circular saw
• Tape measure
• Drill - electric or cordless
• Jig saw
8
9
FIGURE 5.
DESIGNING YOUR POLK EX SUBWOOFER ENCLOSURE STEP BY STEP
1.) How much room do you have to work with in your car or truck?
2.) Which of the above enclosures sounds the best to you?
When designing your subwoofer enclosure, the first thing you need to figure out is just how
large an enclosure will fit in your vehicle. When an enclosure is going in the trunk of a car,
you first need to measure your trunk to find the maximum height, width, and depth
available. Pay attention to trunk hinges and tension bars. If your enclosure is going in an
area other than a trunk, make sure you check for similar obstructions. After measuring,
subtract 1.5" from each dimension. This compensates for the thickness of the material you
use, and will give you your usable (internal) dimensions. Record these dimensions in the
space below for future reference.
17 1/2" 16"
34"
Maximum dimensions
Usable dimensions
Height:__________inches
Width:___________inches
Depth:___________inches
(Minus 1.5 inches)=______inches
(Minus 1.5 inches)=______inches
(Minus 1.5 inches)=______inches
Usable volume=________cubic inches
Usable volume=________cubic feet
35 1/2"
You now have all the dimensions you need to begin cutting out your wood. The illustration
above shows a diagram of the enclosure with all the panel sizes that need to be cut.
After you have cut all of the wood, it’s time to start assembling your enclosure. Before you
assemble your enclosure there are a few things we recommend doing. You will need to cut
out the hole for your EX subwoofer and your terminal cup. The terminal cup is a connector
that allows you to plug and unplug the wires from your amplifier into the enclosure. You
may want to have a friend help you with assembly since it’s hard to hold the pieces together
and assemble them at the same time. When building your subwoofer enclosure, we suggest
that you use wood glue in combination with wood screws for the strongest joint. We also
suggest that you use one screw about every three inches along the seams of your enclosure.
Assemble the enclosure as shown in the above diagram, but leave one side off. We suggest
that you leave off the baffle board. This will allow you to seal your enclosure more easily,
and an air-tight seal is crucial! The best way to insure an air-tight seal is to seal the inside of
your enclosure with quality silicone caulk. This also includes sealing around your input
terminal cup, and, if you are using a ported enclosure, around your port. It is not advised to
use silicone around your subwoofer when mounting it to the baffle. Instead, we recommend
using the foam gasket weather stripping supplied with your EX subwoofer. When mounting
your subwoofer to the baffle board, pre-drill your mounting holes using the template
supplied. This will make the mounting of your subwoofer easier and will help prevent
damage to your subwoofer from a slip of the drill. When securing your subwoofer to the
enclosure we recommend using bolts and tee-nuts, but if you prefer, you can use wood
screws. Whichever you use, make sure it is at least 1.25" long. This will insure a good grip
into the wood.
Multiply your usable Width x Height x Depth. The product will be the usable (internal) volume
of your enclosure in cubic inches. Divide this number by 1728 (the number of cubic inches in a
cubic foot). This will give you the internal volume in cubic feet. Divide your internal cubic feet
by 2 (only if you are using a pair of EX subwoofers). Compare this number to the chart on page
14 of this manual. Choose the recommended enclosure which is closest in size. Now that you
have all of your needed dimensions, you can begin cutting your wood. From the above chart
you can tell how big each piece of wood should be. Here’s a sample enclosure.
Maximum dimensions
Height:__________inches
Usable dimensions
(Minus 1.5 inches)=______inches
17.5
16
Width:___________inches
(Minus 1.5 inches)=__3_4___inches
35.5
Depth:___1_1_.5______inches
(Minus 1.5 inches)=__1_0___inches
5440
Usable volume=________cubic inches
3.15
Usable volume=________cubic feet
By looking on the chart at the bottom of page 14 of this manual, you’ll find that this usable
volume is slightly more than double the recommended volume for a single EX12, in either
a sealed or vented enclosure. Assuming that you will be using a pair this will work out well.
If you are using a single subwoofer, you can cut your width in half. Since we will be using a
pair of EX12 subwoofers for our sample enclosure, we now need to determine the center
divider displacement and the resulting total usable volume. This can be figured out by
multiplying the height x depth x thickness of the divider, and subtracting that number from
the total usable cubic inches. Using the example above yields the following result:
[5440 in3 - (16" x 10" x 3/4")] = [5440 in3 - 120 in3] = 5320 in3 total usable volume.
10
11
AMPLIFIER POWER REQUIREMENTS
Your speakers will work well with a variety of electronic components. As little as 50 watts
per channel will deliver adequate listening levels in most cars. If you have a noisy car or
intend to play your system at loud listening levels, more power is necessary to achieve the
best performance. More power is always better. Consult your Polk Audio dealer for
specific recommendations.
When building a ported enclosure we suggest that, whenever possible, you locate the port on
the same baffle as your subwoofer. Your port should be unobstructed both in front of and
behind it by at least 1 to 2 times the diameter of the port. If, on the inside of your enclosure,
the port comes within 1 to 2 times its diameter of the rear wall, you will need to “bend”
your port tube. If you are using PVC pipe you can either cut your port on a 45 degree angle
and rotate the cut portion by 90 degrees, and glue (using PVC cement) or you could buy a
90 degree elbow from your local hardware store. If you are using a card board port tube you
will have to use the cut and rotate method. Since you will be unable to install a “bent” port
from outside the enclosure, you can now see why we recommended leaving your baffle
board off until last.
SAFE LIMITS OF OPERATION
Your Polk loudspeakers are made with the highest quality materials for years of trouble-free
performance. However, damage to loudspeakers can occur when an amplifier, regardless of
its wattage, is made to play at higher listening levels than its power can clearly produce
(usually beyond the “1 to 2 o’clock” position on the volume control).
Finally, one last thing you could do to your enclosure before installing it is to stuff it. The
primary reason for stuffing an enclosure is to “trick” the woofer into thinking that the
enclosure is larger than it actually is. You would want to do this if you build your box
smaller than the recommended size. By stuffing the box you can build the box as much as
10% smaller than recommended and still achieve the same net result as the full size
unstuffed box. The easiest way to do this is to use dacron pillow stuffing which can be
purchased from craft stores fairly inexpensively. The rule of thumb for stuffing your
enclosure is 1 pound of dacron per cubic foot. When putting the dacron into your enclosure,
do not pack it in, rather place it evenly around the inside of the enclosure. When stuffing a
ported enclosure, it is important not to obstruct the port with the dacron.
This results in very high levels of audible distortion, originating in the amplifier, which
adds a harsh, gritty sound to the music. Contrary to popular belief, a speaker is more likely
to be damaged by trying to get too much volume from a low-powered amp than from a
high-powered one.
LOW FREQUENCY CUT - OFF FOR SYSTEMS WITH SUBWOOFERS
Now that you have a subwoofer in your system, you may want to decrease the amount of
bass going to your mid-range speakers. This will get you better midrange sound and
increase the power handling. There are two ways to roll off the bass before it gets to the mid-
range speakers. One way is to use a “bass blocker”, a capacitor placed in series with the
main input. The other route is to use an electronic crossover device which allows filtering
below 100 Hz or so.
Although your new EX subwoofers were designed to work in a wide variety of enclosures and
configurations, we have included only the most popular ones. For more enclosures and
configurations, please contact your local authorized Polk Audio dealer. We hope that this
manual has helped to take the mystery out of designing an enclosure for your new Polk
Audio EX Subwoofers.
TECHNICAL ASSISTANCE
Good luck and enjoy your new Polk EX Series II Subwoofers. If you need assistance or have
any questions, call 1-800-377-POLK (7655) between 9am and 5pm, Monday through Friday
Eastern Time.
12
13
EX SERIES II SUBWOOFER SPECIFICATIONS
EX SERIES II 1 YEAR WARRANTY
Polk Audio, Inc. warrants the original purchaser only that this Polk Audio EX Series II
EX8
EX10
EX12
THIELE/SMALL PARAMETERS
Product (the Product) will be free from defects in materials and workmanship for a period
of (1) one year from the date of original retail purchase from a Polk Audio Authorized
Dealer. However, this warranty will automatically terminate prior to the expiration of the
(1) one year period if the original retail purchaser sells or otherwise transfers the Product to
any other party. The original retail purchaser shall herein after be referred to as "you." To
allow Polk Audio to offer the best possible warranty service, please fill out the Product
Registration Card(s) and send them to the Factory at the address provided in the
Registration Card within (10) ten days of the date of purchase.
Type
subwoofer
8"
subwoofer
10"
subwoofer
12"
Driver Complement
Nominal Impedance
Frequency response
Fs (Hz)
Re
Le
Qms
Qes
4ohms
20-300Hz
44.64Hz
3.73 ohms
1.57 mH
11.43
4ohms
20-400Hz
32.47Hz
3.34 ohms
1.55 mH
8.27
4ohms
20-500Hz
24.47Hz
3.38 ohms
1.40 mH
8.14
0.57
0.54
0.48
0.31
0.30
Qts
0.45
1.59 ft3
44.56L
150watts
400watts
92 dB
0.177 in.
4.5 mm
2.0 in.
4 11/16"
120 mm
5 1/16"
130 mm
9 1/16"
230 mm
Vas (cubic feet)
Vas (liters)
0.66 ft3
18.51L
125watts
300watts
90 dB
4.72 ft3
132.02L
150watts
400watts
93 dB
Defective Products must be shipped, together with a proof of purchase, prepaid insured to
the Authorized Polk Audio Dealer from whom you purchased the Product, or to the Factory
at the address given in this booklet. Products must be shipped in the original shipping
container or its equivalent; in any case the risk of loss or damage in transit is to be borne by
you. If, upon examination at the Factory or Polk Audio Authorized Dealer it is determined
that the unit was defective in materials or workmanship at any time during the Warranty
period, Polk Audio or the Polk Audio Dealer will, at its option, repair or replace this Product
at no additional charge, except as set forth below. All replaced parts and Products become
property of Polk Audio. Products replaced or repaired under this Warranty will be returned
to you, within a reasonable time, freight prepaid.
Power Handling (watts continuous)
Power Handling (watts peak)
Sensitivity (SPL at 1 watt / 1 meter)
Xmax (inches)
Xmax (millimeters)
Voicecoil Diameter
Mounting depth (inches) top mount
(millimeters)
Mounting depth (inches) bottom mount 4 1/4"
(millimeters)
Mounting diameter (inches)
(millimeters)
RECOMMENDED ENCLOSURES
Sealed
Sealed volume(cubic feet)
(liters)
Ported
Ported volume(cubic feet)
(liters)
Port diameter (inches)
(millimeters)
Port length (inches)
(millimeters)
Tuning frequency (Hz)
Bandpass
Bandpass total volume (cubic feet)
(liters)
Front chamber volume (cubic feet)
(liters)
0.177 in.
4.5 mm
1.5 in.
3 7/8"
85 mm
0.177 in.
4.5 mm
2.0 in.
5 3/8"
135 mm
5 3/4"
145 mm
10 7/8"
276 mm
110 mm
7 1/8"
180 mm
This Warranty does not include service or parts to repair damage caused by accident,
disaster, misuse, abuse, negligence, inadequate packing or shipping procedures,
commercial use, voltage inputs in excess of the rated maximum of the unit, cosmetic
appearance of the cabinetry not directly attributable to defects in materials or
workmanship, or service, repair, or modifications of the Product which has not been
authorized or approved by Polk Audio.
.5 ft3
14.2 L
.65 ft3
18.4 L
.95 ft3
26.9 L
.75 ft3
21.2 L
3 in.
75 mm
10 1/4"
255 mm
45Hz
1.0 ft3
28.3 L
3 in.
75 mm
11 1/4"
280 mm
38 Hz
1.25 ft3
35.4 L
4 in.
100 mm
12 5/16"
305 mm
40 Hz
This Warranty is in lieu of all other expressed Warranties. If this Product is defective in
materials and workmanship as warranted above, your sole remedy shall be repair or
replacement as provided above. In no event will Polk Audio, Inc. be liable to you for any
incidental or consequential damages arising out of the use or inability to use the Product,
even if Polk Audio, Inc. or a Polk Audio Dealer has been advised of the possibility of such
damages, or any other claim by any other party. Some states do not allow the exclusion or
limitation of consequential damages, so the above limitation and exclusion may not apply
to you. This Warranty gives you specific legal rights which may vary from state to state.
1.1 ft3
31.1 L
.70 ft3
19.8 L
.38 ft3
10.8 L
3 in.
75 mm
12 3/8"
310 mm
58 Hz
1.1 ft3
31.1 L
.50 ft3
14.2 L
.60 ft3
17.0 L
3 in.
75 mm
9 7/8"
250 mm
51 Hz
1.5 ft3
42.4 L
.75 ft3
21.2 L
.72 ft3
20.4 L
4 in.
100 mm
19 3/16"
480 mm
46 Hz
Back chamber volume (cubic feet)
(liters)
Port diameter (inches)
(millimeters)
Port length (inches)
(millimeters)
Back chamber tuning frequency (Hz)
This warranty applies only to Products purchased in the United States of America, its
possessions, and U.S. and NATO armed forces exchanges and audio clubs. The Warranty
terms and conditions applicable to Products purchased in other countries are available
from the Polk Audio Authorized Distributors in such countries.
14
15
|