Planet Technology Network Card NAS 7100 User Manual

1-Bay SATA NAS Server  
NAS-7100  
Quick Installation Guide  
Version:1.0  
 
Thank. you. for. purchasing. PLANET. 1-Bay. SATA. NAS. Server,. NAS-7100.. In. this.  
installation.guide,.it.illustrates.the.simply.installation.for.user.to.install.a.HDD.and.  
install. NAS-7100. to. Windows. system.. For. more. information,. please. also. refer. to.  
the.User’s.manual.in.our.CD-ROM.  
 
System  
Package Contents  
The.following.items.should.be.included.in.the.NAS65.packaging.  
If. any. of. these. items. are. damaged. or. missing,. please. contact. your. dealer. for.  
replacements.  
•. NAS-7100  
•. Quick.Installation.Guide  
•. Setup.CD  
•. Ethernet.Cable.  
•. Power.Adapter.with.Power.Core  
System Requirements  
•. Windows.95,.98,.ME,.NT.4.0,.2000/2003,.XP.or.Vista.  
•. Ethernet.Network.employing.10BaseT,.100BaseTX.or.1000BaseT.  
•. TCP/IP.protocol.  
Front Panel  
Rear Panel  
 
HDD Install/Remove  
The.NAS-7100.supports.one.3.5-inch.Serial-ATA.(SATA).hard.drive..NAS-7100.does.  
not support low profile or half high hard drive.  
HDD Install  
1..Make.sure.the.NAS-7100.is.powered.off  
2..Open.top.cover.of.NAS-7100  
3..Make.sure.your.hard.drive.is.SATA.interface.and.make.sure.you.back.up.all.pre-  
existing.data.before.use.it.on.NAS-7100  
4..Pull.up.the.HDD.tray.then.slide.and.push.the.HDD.into.the.tray,.make.sure.con-  
nector.well.connecting  
5..Push.down.the.HDD.tray  
6. Put the top cover of NAS-7100 back to finish HDD install  
HDD Remove  
1..Make.sure.the.NAS-7100.is.power.off.  
2..Open.top.cover.of.NAS-7100  
3..Pull.up.the.HDD.tray,  
4..Pull.out.the.HDD.till.SATA.connector.release.then.the.HDD.can.slide.out.of.HDD.  
tray  
 
System Installation  
Boot up  
1..Connect. the. network. cable. to. LAN. port. on. the. rear. of. NAS-7100.. Connect. the.  
others.end.to.your.hub.or.switch.  
2..Connect. the. supplied. power. adapter. to. a. power. outlet. and. plug. the. power. cord.  
into.NAS-7100’s.power.input.on.the.rear.panel.  
3..Power.on.  
.
Locate. the. NAS-7100’s. power. switch. on. the. NAS-7100. real. panel.. Press. it. once.  
to.power.on.the.NAS  
4..The.NAS-7100.self-test.  
.
The. NAS-7100. will. run. a. brief. self-test.. During. the. self-test,. all. of. NAS-7100’s.  
LED will be illuminated or flashing.  
5..Booting.up.  
.
When.the.self-test.is.complete,.boot.up.will.start..The.Ready.LED.will.blink.con-  
tinuously,. and. the. LAN. LED. will. blink. occasionally.. Boot. up. should. take. approxi-  
mately.1-3.minutes.  
6..Boot.up.completed.  
.
When.the.Ready.LED.stops.blinking,.and.remains.on,.boot.up.is.complete..If.the.  
Status. (Orange). LED. stays. on,. or. if. the. NAS-7100. repeatedly. beeps,. there. is.  
a. hardware. problem.. Consult. the. Troubleshooting. section. of. the. User. Guide. for.  
possible.solutions.  
Shutdown  
To. shutdown. the. NAS-7100,. press. the. power. switch. to. start. the. shutdown.  
sequence..Wait.for.all.LEDs.to.turn.off.  
Removing a USB device  
1..Press.the.USB.eject.button.(for.USB.1.or.2).on.the.rear.panel.  
2..Wait.for.the."USB".LED.turn.off.  
3..Remove.the.USB.device.  
You.can.also.use.the.Windows.utility.installed.from.the.CD-ROM:  
1..Select.“Safely.Remove.USB.Device".  
2..Select.the.desired.NAS.and.USB.device,.and.click.the."Eject".button.  
3..Wait.for.the.message.telling.you.it.is.safe.to.remove.the.USB.device.  
If. the. USB. device. is. not. removed,. it. will. not. be. re-connected.. You.  
must.remove.and.re-insert.the.USB.device.to.have.it.re-connected.  
Note  
 
Configuration  
•. This.procedure.only.needs.to.be.done.ONCE,.by.the.NAS-7100’s.Administrator.  
•. Other. LAN. users. should. follow. the. advice. given. in. using. your. NAS. described. in.  
the.following.section.  
Quick Setup with the NAS Wizard  
1..Please. insert. User’s. Manual. and. Utility. CD. into. the. CD-ROM. drive. to. initiate. the.  
autorun.program..Once.completed.a.menu.screen.will.appear.  
2..Click. on. “Initial. Utility”. hyper. link. to. initiate. the. installation.. If. the. autorun. pro-  
gram. is. not. process. in. your. PC,. you. can. click. the. “Start”. button. and. choose.  
“Run..(Suppose.E”.is.your.CD-ROM.drive)..When.the.dialog.box.appears,.enter.  
“E:\Utility\Setup.exe”.and.press.enter.key..You.will.see.the.dialog.box.as.below..  
Please.click.the.“Setup”.button..  
3..After. click,. you. will. see. the. screen. as. below.. The. utility. will. auto. search. your.  
network and find out your NAS-7100.  
 
A. list. of. all. the. NAS-7100s. on. your. network. will. show. on. the. left. side.. The. right.  
side.displays.details.of.the.currently.selected.NAS-7100..  
If.the.desired.NAS-7100.is.not.listed,.check.the.following:  
• The NAS-7100 has finished the start up and boot process.  
•. Your.PC.and.the.NAS-7100.are.on.the.same.IP.segment.  
•. Click.“Refresh”.button.to.search.again.  
Otherwise,.select.the.desired.NAS-7100,.and.click.the."Next".button.  
4..The. following. screen. will. then. be. displayed.. You. can. set. the. IP. settings. in. this.  
screen. Please click “Next” after the configured.  
Obtain an IP address  
Select.this.only.if.your.LAN.has.a.DHCP.Server..  
automatically (DHCP  
Client)  
This.option.is.recommended..You.need.to.enter.the.  
following.data.  
•. IP.address.-.The.utility.will.suggest.a.unused.IP.  
address.within.the.address.range.used.on.your.  
LAN..If.you.wish,.you.can.change.this,.but.you.  
must.ensure.the.address.is.unused.  
•. Network.Mask.-.This.must.match.the.value.used.  
by.PCs.on.your.LAN.  
Fixed IP Address  
•. Gateway.-.This.must.match.the.value.used.by.PCs.  
on.your.LAN.  
 
5. You can configure the time settings in this screen. Please click “Next” after the  
configured.  
The.Default.Name.is.shown..You.may.change.this.if.  
you.wish.  
Server Name  
Normally,.this.name.should.match.the.Workgroup.  
Workgroup Name  
name.used.by.PCs.on.your.LAN.  
Select.your.time.zone.from.the.list.  
Time Zone  
Enter.the.local.date.(mm/dd/yyyy.format).and.time.  
Local Date/Time  
6. Please check the configured settings of this screen, if all the configure are cor-  
rect..Please.click.“Save”.button..  
 
7..After.click."Save",.you.will.see.the.dialog.box.to.prompt.you.again..Please.click.  
“OK”.to.save.or.click.“Cancel.to.check.the.settings..  
8..If.you.would.like.to.install.Flash-Map”.to.helps.you.to.mapping.NAS-7100.now,.  
please. click. “Yes”. and. refer. to. the. manual. in. our. bundled. CD. disk,. otherwise,.  
please click “No” to finish the configuration, then close the initial utility.  
10  
 
Using Your NAS-7100  
To Use the NAS storage  
1..Open.Network.Neighborhood.(or.My.Network.Places).  
2..Locate. the. NAS-7100.. If. it. is. not. listed,. double-click. Entire. Network.. Then. dou-  
ble-click.the.Workgroup.that.the.NAS-7100.is.in..(By.default,.the.NAS-7100.is.in.  
Workgroup.)  
3..Double. click. on. the. NAS-7100. icon.. You. will. then. see. a. list. of. shares. (shared.  
folders). You can read and write files to these shares, unless the NAS-7100 ad-  
ministrator.has.blocked.access.  
4..To.create.a.shortcut.to.an.NAS-7100.folder,.drag.its.icon.to.the.desktop,.and.ac-  
cept.Windows.offer.to.create.a.shortcut.  
Mapping a Network Drive  
1..Right-click.on.the.desired.share.  
2..On.the.pop-up.menu,.select."Map.Network.Drive...".  
3..Select.a.drive.letter.for.this.folder,.check.the.Reconnect.at.Logon.checkbox,.then.  
click.“OK.  
4..This.drive.will.now.be.available.in.Windows.Explorer,.and.from.the.File-.Open.or.  
File-Save.As.dialog.in.all.Windows.applications.  
Using the Web Interface  
The.Web.interface.of.the.NAS-7100.has.three.major.functions:  
•. Users.may.change.their.password.to.match.their.Windows.Logon.  
•. Server. management. can. be. performed.. Default. ID. is. “admin”. and. default. pass-  
word.is.empty  
•. Download.manager.  
To connect to the NAS with your Web Browser  
1..In. your. Browser's. Address. or. Location. bar,. enter. "HTTP://". and. the. NAS-7100.  
Server’s. IP. Address.. (To. connect. via. the. Internet,. additional. setup. is. required..  
See.the.User.Manual.for.details.)  
2. To browse the files and folders on the NAS-7100, click Disk (Public data) or Flash  
(Public.Data).on.the.main.screen.  
3. To view or download a file, click on its name. To download any file, right-click its  
name.and.choose.“Save.target.as...”  
11  
 
Other Configuration  
If. you. want. to. set. more. detail. settings. of. NAS-7100,. please. refer. to. our. manual.  
and configure with your Web Browser. If you have any difficulty on resolving the  
problem.while.installing.or.using.NAS-7100,.please.feel.free.to.contact.PLANET.for.  
support.  
12  
 

Petsafe Pet Care Product PAC00 12893 User Manual
Philips Answering Machine Telephone Answering Machine User Manual
Philips Blu ray Player BDP3305 User Manual
Philips Electric Shaver 5841XL User Manual
Philips Flat Panel Television UA 35T User Manual
Philips TV Cables SWV6602 User Manual
Philips TV DVD Combo Real Flat TV DVD User Manual
Plantronics Headphones W745A User Manual
Porter Cable Trimmer 23 6602 56 User Manual
PYLE Audio Headphones PLVWH1 User Manual